Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
2
Intended use en
8Intended use
Intended use
Read these instructions carefully. You will only
be able to use your appliance safely and
effectively when you have read them. These
operating and installation instructions should
be retained, and passed onto the buyer if the
appliance is sold.
The manufacturer is exempt from all
responsibility if the requirements of this
manual are not complied with.
The images shown in these instructions are for
guidance only.
Do not remove the appliance from its
protective packaging until it is installed in the
unit. Do not switch on the appliance if it is
damaged in any way. Contact our Technical
Assistance Service.
Before installing your new hob, ensure that it is
being installed according to the assembly
instructions.
This appliance is not suitable for use in a
marine craft, caravan or mobile home.
This appliance must only be used in well
ventilated places. It must not be connected to
a combustion product removal device.
This appliance is not intended for operation
with an external clock timer or a remote
control.
This appliance has been designed for home
use only, not for commercial or professional
use. This appliance is only intended for
cooking purposes, not as a heating system.
The warranty will only be valid if the appliance
is used for the purpose for which it was
designed.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
Never leave the appliance unattended during
operation.
Do not use lids or protective barriers for
children which are not recommended by the
hob manufacturer. They may cause accidents
such as those due to the overheating, ignition
or detachment of fragments of materials.
a person responsible for their safety. Children
should be supervised to ensure that they do
not play with the appliance.
All operations relating to installation,
connection, regulation and conversion to
other gas types must be performed by an
authorised technician, respecting all
applicable regulations, standards and the
specifications of the local gas and electricity
suppliers. Special attention shall be paid to
ventilation regulations.
This appliance leaves the factory set to the
gas type that is indicated on the specifications
plate. If this needs to be changed, please
consult the assembly instructions. It is
recommended you contact the Technical
Assistance Service to change to another gas
type.
Before installing, you need to check that local
distribution conditions are compatible with the
appliance's adjustment indicated on the
specifications plate (gas type and pressure,
power, voltage).
Before you begin, turn off the appliance's
electricity and gas supply.
The supply cable must be attached to the unit
to prevent it from touching hot parts of the
oven or hob.
Appliances with electrical supply must be
earthed.
Cabinets installed above the gas cooktop
must have a minimum clearance of 650 mm
(24”).
The gas pressure regulator supplied with the
appliance must be installed in line with the gas
pipe. (N.G. only).
For pressure testing in excess of 3.5 kPa (1/
2 psig) the appliance and its individual shutoff
valve must be disconnected from the gas
supply piping system.
Important. When using a very large pot, leave
a gap of at least 50 mm (2”) to avoid
damaging any parts in bench top wood,
plastic or other non-heat resistant materials.
Never leave oil or hot fat unattended.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
3
en Important safety information
(Important safety
information
Important safety information
DO NOT MODIFY THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE
MATERIALS IN THE APPLIANCE STORAGE
DRAWER OR NEAR THE APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY
OF THIS APPLIANCE WHILE IT IS IN
OPERATION.
DO NOT USE THIS APPLAINCE AS A SPACE
HEATER.
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or death.
:Warning – Risk of deflagration!
Accumulation of unburned gas in an enclosed
area carries a risk of deflagration. Do not
subject the appliance to draughts. These
might blow out the burners. Carefully read the
instructions and warnings on the operation of
gas burners.
:Warning – Risk of poisoning!
The kitchen will become hot and humid and
combustion products produced when this gas
appliance is used. Make sure the kitchen is
well ventilated, particularly when the hob is in
operation: either keep the natural ventilation
apertures open, or install a ventilation system
(extractor hood). Intense prolonged use of the
appliance may require additional or more
effective ventilation: open a window or
increase the power of the ventilation system.
:Warning – Risk of burns!
■ The hotplates and their immediate vicinity
get very hot. Never touch the hot surfaces.
Keep children under 8 years old well away
from this appliance.
Risk of burns!
■ If the liquefied gas bottle is not upright,
liquefied propane/butane can enter the
appliance. Intense darting flames may
therefore escape from the burners.
Components may become damaged and
start to leak over time so that gas escapes
uncontrollably. Both can cause burns.
Always use liquefied gas bottles in an
upright position.
Risk of fire!
■ Do not store or use corrosive chemicals,
products which produce fumes,
inflammable materials or non-food products
below or near this domestic appliance.
Risk of fire!
■ Fat or oil which is overheated can catch fire
easily. Never leave fat or oil to heat up
unattended. If oil or fats do catch fire, never
use water to put the fire out. Put the fire out
by covering the pan with a lid and switch off
the hotplate.
:Warning – Risk of injuries!
■ Pans which are damaged, are not the right
size, hang over the edge of the hob or are
not positioned correctly can cause serious
injuries. Follow the advice and warnings
provided relating to the cooking pans.
Risk of injuries!
■ In the event of a malfunction, turn off the
appliance’s gas and electricity supply. For
repairs, call our Technical Assistance
Service.
Risk of injuries!
■ Do not tamper with the appliance's interior.
If necessary, call our Technical Assistance
Service.
Risk of injury!
■ If a control knob is too stiff to turn or it is
loose, it must not be used. Contact our
after-sales service immediately to have the
control knob repaired or replaced.
:Warning – Risk of electric shock!
Do not clean the appliance using steam
cleaners.
What to do if you smell gas
■ Do not try to light the appliance.
■ Do not touch any electrical switch; do not
use any phone in your building.
■ Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
■ If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
an authorised person.
:Warning – Risk of fire!
■ The hotplates get very hot. Do not rest
inflammable objects on the hob. Do not
store objects on the hob.
4
5Installation and connection
Installation and connection
Statutory requirements
This installation must conform with the following:
■ Manufacturer’s Installation instructions
■ Local Gas Fitting Regulations
■ Municipal Building Codes
■ Refer to AS/NZS 5601.1 for Gas Installations
■ S.A.A. Wiring Code
■ Local Electrical Regulations
■ Any other statutory regulations
Preparing to install
Installation and connection en
Refer to AS/NZS 5601.1 for piping size details. These
built-in cooktops are intended to be inserted in a
benchtop cutout.
Do not stick the cooktop onto the worktop with silicone.
Only an officially authorised technician should connect
the appliance.
Before you begin, turn off the gas and electricity supply.
Before connecting the unit, check whether the local
connection conditions (type of gas) are compatible with
the unit’s setting. Observe any special conditions
imposed by local suppliers (utilities). The specifications
of this cooktop are stated on the data label located on
the bottom of the cooktop base.
A duplicate data label is supplied for adhesion to an
accessible location near the hotplate if the data label on
the base of the hotplate cannot be accessed when the
hotplate is installed.
PLQ
PLQ
¸
PLQ
PLQ
5
en Installation and connection
Clearances
A range hood fitted above the top must be installed
according to the installation instructions for the range
hood. A minimum distance of 650 mm is required for a
range hood and 750 mm for an exhaust fan.
Any adjoining wall surface situated within 200 mm from
the edge of any hob burner must be a suitable noncombustible material for a height of 150 mm for the
entire length of the hob. Any combustible construction
above the hotplate must be at least 650 mm above the
top of the burner and no construction shall be within
450 mm above the top of the burner.
PLQ
PLQ
A minimum depth of 50 mm from the top of the worktop
surface must be provided for the appliance.
If the base of the hotplate can be touched, a protecting
shield must be fitted.
Installation of cooktop into the kitchen
bench
Side clearances: If the distance measured from the
periphery of the nearest burner to any vertical surface is
less than 200 mm, the surface shall be protected in
accordance with clauses 6.10.1.2 of AS/NZS 5601.1.
Make an appropriate size cut in the work surface.
On wood work surfaces, varnish the cutting surfaces
with a special glue. This protects them from moisture
which could collect under the work surface.
Note: Wear protective gloves to fit the hob.
Depending on the model, the adhesive seal may be
factory-fitted. If this is the case, it should not be
removed under any circumstances, since the adhesive
seal prevents leaks. If the seal has not been factoryfitted, apply it to the underside of the hob.
Fitting the appliance onto the kitchen unit:
1. Screw each one of the clips into the position
indicated so that they are free to rotate.
2. Insert and centre the hob.
Press the sides of the hob until it is supported
around its entire perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the
work surface is.
Do not stick the hob onto the worktop with silicone.
[
■ The shield must be at least 10 mm from the lowest
part of the hotplate and must be capable of
withstanding the appliance temperatures. Minimum
thickness of benchtop is 30 mm.
■ The shield material must be mdf or similar with
minimum thickness of 12 mm.
■ The shield overall dimensions must be 560 mm wide
x 480 mm deep.
■ Provide cut-out in right hand rear of shield of 80 mm
wide x 80 mm deep to provide for gas regulator / LP
connection fitting.
After installation of the shield the clearance around the
top and sides of shield will allow adequate ventilation.
Ensure the side and top clearances are not obstructed.
PLQ
PD[
PLQ
PD[
PLQ
PLQ
PLQ
If an oven is positioned below the cooktop the barrier
does not need to be fitted, but a space of 35 mm must
be maintained between the underside of the cooktop
and the top of the oven.
[
Electrical connection
An electrical 10 amp socket needs to be within 1 m of
the hotplate to allow electrical connection. The socket
must remain accessible after installation of the
appliance.
Important notes:
■ This appliance is connected to the mains (240 VAC)
by means of the connecting lead which must be
fixed to the kitchen unit to prevent it from coming
into contact with hot parts of the cooktop (or an oven
installed underneath) and remain accessible after
installation of the cooktop.
6
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.