Siemens EC945RB91ANG User Manual
86(5,16758&7,216
,167$//$7,21,16758&7,216
0$,17(1$1&(,16758&7,216
7KLVFRRNWRSLVIRUXVHZLWK1DWXUDO*DVDQG8QLYHUVDO/3*
/HDYHWKHVHLQVWUXFWLRQVZLWKWKHRZQHU
(&5%$
GMK10047
Ú Table of contents
[es] Instrucciones de uso y montaje
Safety considerations................................................................ 2
For your safety.....................................................................................2
What to do if you smell gas..............................................................2
Warnings...............................................................................................2
Installation.................................................................................. 3
Statutory requirements.......................................................................3
Preparing to install..............................................................................3
Clearances ...........................................................................................3
Installation of cooktop into the kitchen bench ..............................4
Connection ...........................................................................................4
Converting the cooktop from Nat. Gas to Universal LPG ...........5
Changing the nozzles of the burners on the cooktop .................5
Adjustment of the taps.......................................................................5
Safety considerations
For your safety
DO NOT MODIFY THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
Do not store articles on or against this appliance.
What to do if you smell gas
Do not try to light the appliance.
Do not touch any electrical switch; do not use any phone in your building.
Inmediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by an authorised person.
Warnings
Do not allow the flame to extend beyond the edge of the cooking utensil. This instruction is based on safety considerations.
Do not forget that the unit becomes hot when in use. Common sense is important. Just because the flame is out, does not mean parts cannot still be hot.
This appliance shall not be used for space heating. This instruction is based on safety considerations.
Be sure to disconnect the electrical supply before disassembly of the appliance.
Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapours and liquids.
This appliance must be installed in a position with the proper level of ventilation. Do not obstruct the flow of combustion and ventilation air.
Cabinets installed above the gas cooktop must have a minimum clearance of 650 mm (24”).
The gas pressure regulator supplied with the appliance must be installed in line with the gas pipe. (N.G. only).
For pressure testing in excess of 3.5 kPa (1/2 psig) the appliance and its individual shutoff valve must be disconnected from the gas supply piping system.
Operating instructions .............................................................. 6
Burner locations ..................................................................................6
Accessories .........................................................................................6
Operation..............................................................................................7
Cooking pans ......................................................................................8
Cleaning and maintenance ...............................................................8
Service ..................................................................................................9
Wiring diagram ................................................................................. 10
Produktinfo
Additional information on products, accessories, replacement parts and services can be found at www.siemens-home.com and in the online shop www.siemens-eshop.com
Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave oil or hot fat unattended.
The surfaces on heating and cooking appliances get hot when in use. Be careful. Keep children away from the appliance.
Only use your appliance for the preparation of food and never for room-heating purposes.
This appliance leaves the factory set for the gas supply indicated on the data label. Call the Service Centre if it needs to be altered.
Do not tamper inside the appliance. If necessary, call your local
Service Centre.
Overheated fat or oil can easily catch fire. Never leave the appliance unattended when cooking food with fat or oil, e.g. chips.
Never pour water on burning fat or oil. DANGER OF BURNS! Cover the receptacle to smother the flames and turn the cooktop off.
In the event of a fault, cut the gas and electricity supplies to the appliance. Call our Service Centre to repair the fault.
Do not use unstable or uneven-based receptacles on cooking plates or burners. They may accidentally tip over.
If a gas supply knob/valve jams, do not force it. Call your official Service Centre immediately for them to repair or replace it.
The illustrations used in this booklet are only intended as a guide.
Grids become very hot during use. When operating the appliance control knobs, take care not to make contact with the grids.
Do not use this appliance neither in marine craft nor in caravans.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance if it ever changes owner.
Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices.
SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL BE HELD LIABLE.
2
Installation
Statutory requirements
This installation must conform with the following:
■ Manufacturer’s Installation instructions
■ Local Gas Fitting Regulations
■ Municipal Building Codes
■ Refer to AS/NZS 5601.1 for Gas Installations
■ S.A.A. Wiring Code
■ Local Electrical Regulations
■ Any other statutory regulations
Preparing to install
Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout.
Only an officially authorised technician should connect the appliance.
Before you begin, turn off the gas and electricity supply.
Before connecting the unit, check whether the local connection
conditions (type of gas) are compatible with the unit’s setting.
Observe any special conditions imposed by local suppliers
(utilities). The specifications of this cooktop are stated on the
data label located on the bottom of the cooktop base.
A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed.
Clearances
A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan.
Any adjoining wall surface situated within 200 mm from the
edge of any hob burner must be a suitable non-combustible
material for a height of 150 mm for the entire length of the hob.
Any combustible construction above the hotplate must be at
least 650 mm above the top of the burner and no construction
shall be within 450 mm above the top of the burner.
PLQ
PLQ
3
A minimum depth of 50 mm from the top of the worktop
surface must be provided for the appliance.
If the base of the hotplate can be touched, a protecting shield must be fitted.
The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm.
PLQ
PD[
PLQ
PD[
PLQ
PLQ
PLQ
If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven.
Installation of cooktop into the kitchen bench
Side clearances: If the distance measured from the periphery of
the nearest burner to any vertical surface is less than 200 mm,
the surface shall be protected in accordance with clauses
6.10.1.2 of AS/NZS 5601.1.
For cutout dimensions and clearances see Preparing to install.
Installation procedure:
The clips and the adhesive seal (underside of the cooktop) are already fitted (depending on the model), do not under any circumstances remove them. The seal ensures that the entire work surface will be watertight, and prevents water seepage.
Fitting the appliance onto the kitchen unit:
1. Place the cooktop in the correct position then loosen each of
the clips so that they all turn freely (it is not necessary to
completely undo them).
2. Insert and centre the cooktop.
Press the sides of the cooktop until it is supported around its entire perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work surface is.
Connection
Electrical
An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain accessible after installation of the appliance.
Important notes:
■ This appliance is connected to the mains (240 VAC) by
means of the connecting lead which must be fixed to the
kitchen unit to prevent it from coming into contact with hot
parts of the cooktop (or an oven installed underneath) and
remain accessible after installation of the cooktop.
When making this connection make sure that the lead cannot come into contact with hot parts of the cooktop.
■ This appliance must be earthed. When connecting the
cooktop ensure that the earth wire is connected first and that
all wires are connected to the correct terminals.
99
a
/
9
9
1
Gas
During the planning stage, consider the position of supply connections.
The cooktop must be connected to the gas supply with
upstream connection of an isolation valve in accordance with
the respectively valid regulations. We recommend that the
isolation valve be fitted prior to the cooktop to enable isolation
of cooktop from gas supply. The valve must be easily
accessible at all times.
To find out the factory set gas type, see bottom of cooktop next to gas connection.
Remove plastic cap from gas supply line prior to installation.
Fit regulator (N.G.) or a test point (Universal LPG) directly to the R 1/2’’ connection.
Direction of gas flow is indicated on the rear of the regulator.
For position of the inlet connection refer Preparing to install:
Use pipe compound or thread sealant, properly theaded pipes and careful assembly procedure so that there is no cross threading, etc., which might cause damage or leakage.
Make sure that all connections peformed are free of leakage. The manufacturer does not accept any liability for leakage on connections performed by the installer or if the L-tube is moved or twisted.
There are two ways to carry out the connection to the main gas line:
■ The hotplate can be connected with rigid pipe as specified in
AS/NZS 5601.1
■ Flexible Hose: If installing with a hose assembly, it must
comply with AS/NZS 1869, 10 mm ID, class B or D, no more
4
Loading...