Siemens CFFC1310-LP User Manual

Instruction Manual for Colour Fixed Dome Camera

English

CFFC1310-LP 2GF1184-8AC CFFC1315-LP 2GF1184-8AA

Model number Part Code

Warning

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. The CAUTION label shown above is attached to the dome. CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Servicing should only be carried out by qualified service personnel.

Document / Document / Dokument A24205-A336-R555 Edition / Editie / Ausgabe Rev A.1 Supersedes / Vervangt / Ersetzt -

Instructiehandleiding Fixed focus kleuren domecamera

Modelnummer Art. code

Installationsanleitung Fixfokus-Dome-Farbkamera

Typen-Nummer Art.-Nr

CFFA-TD 2GF1086-8AA Tinted Lower Dome / NL: Getinte dome / De: Getönte Kuppel CFFA-IC29 2GF1086-8AB 2.9 mm — Replacement Lens / NL: Vervangingslens / D: Ersatzlinse CFFA-IC37 2GF1086-8AK 3.7 mm — Replacement Lens / NL: Vervangingslens / D: Ersatzlinse CFFA-IC60 2GF1086-8AF 6.0 mm — Replacement Lens / NL: Vervangingslens / D: Ersatzlinse CFFA-IC12 2GF1086-8AE 12.0 mm — Replacement Lens / NL: Vervangingslens / D: Ersatzlinse

Accessories / Accessoires / Zubehör

Waarschuwing

Open de behuizing niet, want dan loopt u het risico op een elektrische schok. Laat alle reparaties door gekwalificeerde technici uitvoeren. De bovenstaande waarschuwingssticker is op de dome bevestigd. LET OP: Om het risico op elektrische schokken te verkleinen, dient u de kap (of achterzijde) niet te verwijderen. In het apparaat bevinden zich geen onderdelen die u zelf kunt repareren. Laat elke vorm van onderhoud over aan gekwalificeerde technici.

Warnung

Zur Vermeidung von Elektroschocks darf das Gehäuse nicht geöffnet werden. Servicearbeiten dürfen nur von qualifiziertem Personal ausgeführt werden. Der Warnhinweis oben ist an der Kuppel angebracht. VORSICHT: Um die Gefahr eines Elektroschocks zu verringern, darf das Gehäuse (oder die Rückseite) nicht entfernt werden. Im Inneren befinden sich keine benutzerseitig zu wartenden Teile. Servicearbeiten dürfen nur von qualifiziertem Kundendienstersonal ausgeführt werden.

Intended for indoor use only!

Nur für den Einsatz im Innenbereich vorgesehen!

Alleen geschikt voor binnentoepassingen!

97,5 mm

112 mm

Package contents

• Dome camera

• 1 BNC connection cable

• 1 service monitor cable

• 2 fixing screws

• 2 wall plugs

• Fixing template

• Installation and operating instructions (this document)

Dome camera parts

See figures A and B.

1. Cable entry holes

2. Unit casing

3. Inner liner

4. Dome casing

5. Mode setting DIP switches

6. V phase adjustment screw

7. Monitor output

8. Unit mounting holes

9. BNC connector

10.Power connector

11.Locking ring

12.Panning adjustment wheel

13.Axial ring

Installing the camera

Step 1: Connecting the cables

1. Connect the BNC cable to the BNC connector (9).

2. Connect the power supply cable to the power connector (10). Use a 24 V AC or 12 V DC power supply.

Caution

If using a DC supply, make sure the polarity is correct. Incorrect connection may cause malfunction and/or damage to the video camera.

3. Guide the cables through the cable entry holes (1).

Step 2: Mounting the camera

1. Place the template on the mounting surface and mark the holes.

2. Drill two holes as marked.

3. Insert the wall plugs into the holes.

4. Fasten the unit with the screws provided.

Step 3: Adjusting the camera position

1. Hold the lens so that it does not rotate.

2. Loosen the locking ring (11) and panning adjustment wheel (12).

Caution

Do not loosen the locking ring without holding the lens in place; otherwise, the lens may rotate with the locking ring and the cable may twist.

3. Turn the axial ring (13) in the desired direction.

Note

If the camera does not rotate smoothly, loosen the locking ring completely. The locking ring has an internal stop and will not come off.

Caution

Do not turn the lens more than 360° as this may cause internal cables to disconnect or break.

4. Using the axial ring, carefully adjust the image to the desired angle of view.

5. Lightly tighten the locking ring (11) and panning adjustment wheel (12)

6. Hold the lens and fully retighten the locking ring (11) and panning adjustment wheel (12).

Optional settings

• Adjust the phase difference between cameras (use V Phase adjustment screw (6).

• Set the DIP switches (5) to activate or deactivate the following features:

• Backlight compensation (BLC)

• Automatic gain control (AGC).

Automatically adjusts the picture to suit ambient brightness

• Automatic electronic shutter (DC/AES).

Automatically adjusts the picture to suit the brightness of the subject.

Caution

Do not turn the DC/AES Mode switch to on otherwise the electronic shutter speed will be permanently set to 1/60(EIA) or 1/50(CCIR).

• Line Lock (LL).

Set camera synchronisation to internal (OFF) or line lock (ON). Line lock is only available with a 24 V AC supply.

Step 4: Attaching the dome to the unit

See figure C.

Note

Use a soft lint-free cloth to wipe the dome cover clean and remove fingerprints.

1. Clean the joint surfaces of the unit.

2. Place the inner liner on the unit.

3. Place the dome on the unit.

4. Turn the dome clockwise and lock the cover in place.

General guidelines

Operation and storage

• Avoid facing the camera directly toward very bright objects (such as light fittings) for an extended period.

• Do not operate or store the unit in the following locations:

• Extremely hot or cold places.

• Close to sources of strong magnetism.

• Close to sources of powerful

electromagnetic radiation, such as radios or TV transmitters.

• In humid or excessively dusty places.

• Where exposed to mechanical vibration.

• Close to fluorescent lamps or objects that

reflect light.

• Under unstable or flickering light sources.

Cleaning

• Use a soft, dry cloth to remove fingerprints or dust from the dome.

• If the dome is very dirty, use a small amount of mild detergent on a damp cloth for cleaning. Ensure the dome is dry before attaching the dome to the unit.

Caution

Do not use volatile solvents such as alcohol, benzene or thinners. These solvents may damage the surface.

Transportation

Use the original packing material or materials of equal quality.

CCD characteristics

The following conditions may be observed when using a CCD camera. These are inherent to the design and do not stem from any fault within the camera itself.

• Vertical smear: This phenomenon occurs when viewing a very bright object.

• Patterned noise: This is a fixed pattern which may appear over the entire monitor screen when the camera is operated at a high temperature.

• Jagged picture: When viewing stripes, straight lines, or similar patterns, the image on the screen may appear jagged.

Specifications

General

Power requirement......12 V DC or 24 V AC

(Min. 5 W)

Power consumption ....3,5 W (max.)

Operating temperature-10 to +50°C, 90% RH max. Storage temperature...-20 to +60°C, 70% RH max.

External dimensions....112 x 97.5 mm

Weight.........................Approx. 0.29 kg

Unit material................ABS (30%) and

polycarbonate (70%)

Dome material.............Polycarbonate

Imaging system

Imaging device............Interline transfer 1/3 inch

CCD Effective picture elements

CFFC1310-LP (Std. Res.)

PAL: 500(H) * 582(V)

CFFC1315-LP (High Res.)

PAL: 752(H) * 582(V)

TV system...................PAL: 2:1 Interlace,

15.750 kHz horizontal,

50 Hz vertical

Optical system and other specifications

Focal length ................f=3.7 mm

Maximum relative aperture

F2.0 Synchronisation system

Internal or Line lock (24 V

AC only) Horizontal resolution ...480 TV lines — High

Resolution model

330 TV lines — Std

Resolution model Minimum illumination ..0.56 lx — High Resolution

model

0.31 lx — Std Resolution

model

(AGC ON, more than 50%

of image output r = 0.45,

without dome cover)

Video output................1.0 Vp-p 75 Ohm

Video S/N ratio............More than 50 dB (AGC

OFF, Weighted)

White balance .............Automatic (2500°K -

10000°K)

AGC ............................ON/OFF switchable

BLC.............................ON (Center measured) /

OFF switchable

Information

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference in which case the user will be required to correct the interference at his own expense.

English

+ 2 hidden pages