Siemens AS200, AS200A, AS300 Operating Manual

Gigaset AS200/AS200A/AS300

±V

11.12. 11:56 INT MENU

1Charge status of

the batteries

2Answer machine icon

(AS200A only) 3Display keys 4Message key

Flashes: new messages

received 5 AS200/AS200A:

h Directory key

AS300:

d Handsfree key

6 Control key (u) 7 Talk key 8 AS300:

h Directory key

(press down) 9End call and

On/Off key

10 Ringer on/off

(press and hold

in idle status)

11 Keypad lock on/off

(press and hold)

12 Recall key

- Consultation call

(flash)

- Dialling pause

(press and hold)

13 Microphone 14 "Microphone off" key

The base station at a glance

AS200A base station

AS200/AS300 base station

The handset at a glance

1 Registration/paging key:

Search for handsets (press briefly, "Paging"

¢ page 10)

¢ page 10).

2 On/Off key: activate and deactivate answer machine.

Lights up: answer machine is activated.

3 Volume keys: (– = quieter; + = louder)

During message playback: adjust the speaking volume. While phone is ringing: adjust ringer volume.

4 Play/Stop key:

Play back messages from the answer machine, or cancel playback. Flashes: there is at least one new message or message is in the process of being recorded.

Flashes very quickly: memory is full.

During message playback:

5 Delete current message. 6 Skip to the start of the current message (press once) or go to the pre-

vious message (press twice).

7Skip to next message.

Display keys on handset:

Pressing a key launches the function that appears above that key in the display.

AS200/AS200A AS300

Display icon

Function when pressed

INT

Call other registered handsets

¢ page 11.

Open main/submenu (see Menu tree

¢ page 16).

“

Go back one menu level.

Scroll up/down or adjust volume with u.

Move cursor to left/right with u.

Backspace deletes one character at a time from right to left.

Confirm menu function or save entry.

Safety precautions

Read this user guide and the safety precautions carefully before use. Explain their content and the potential hazards associated with using the telephone to your children.

Only use the mains adapter supplied.

Fit only the recommended, rechargeable batteries

(¢ page 13), i.e. never use any other

battery type or non-rechargeable batteries as this could result in significant health risks and personal injury.

The operation of medical appliances may be affected. Be aware of the technical conditions in

your particular environment, e.g. doctor's sur-

gery. Do not hold the rear of the handset to your ear

when it is ringing. Otherwise you risk serious and permanent damage to your hearing. The handset may cause an unpleasant humming noise in hearing aids.

Do not install the phone in a bathroom or shower room. The handset and base station are not splashproof.

Do not use your phone in environments with a potential explosion hazard, e.g. paint shops.

If you give your Gigaset to someone else, make sure you also give them the user guide.

Please remove faulty base stations from use or have them repaired by our service, as they could interfere with other wireless services.

Disposal

Batteries should not be disposed of in general household waste. Observe the local waste dis posal regulations, details of which can be obtained from your local authority or the dealer you purchased the product from. All electrical and electronic equipment must be disposed of separately from general household waste using the sites designated by local authori ties. If a product displays this symbol of a crossed-out rubbish bin, the product is subject to European Directive 2002/96/EC. The appropriate disposal and separate collection of used equipment serve to prevent potential harm to the environment and to healt h. They are a precondition for the re-use and recycling of used electrical and electronic equipment. For further information on disposing of your used equipment, please contact your local authority, your refuse collection service or the dealer you purchased the product from.

Emergency numbers cannot be dialled if the keypad lock (

¢ page 1) is activated!

Not all of the functions described in this user guide are available in all countries.

Care

Wipe down the base station and handset with a damp cloth (no solvents) or an antistatic cloth. Never use a dry cloth. This can cause static.

Contact with liquid

If the handset should come into contact with liquid:

◆ Switch the handset off and remove the batteries

immediately.

◆ Allow the liquid to drain from the handset.

◆ Pat all parts dry, then place the handset with the

battery compartment open and the keypad facing down in a dry, warm place for at least 72 (not in a microwave, oven etc.).

◆ Do not switch on the handset again until it is

completely dry.

When it has fully dried out, you will normally be able to use it again.

ECO DECT

You are helping to protect the environment with your Gigaset AS200/AS200A/AS300.

Reduced energy consumption

Your telephone has a power-saving adapter plug and uses less power.

Reduced transmission power

The transmission power of your telephone is reduced automatically:

The handset's transmission power is reduced depending on the distance to the base station. The transmission power on the base station is reduced to virtually zero when only one handset is regis tered and the handset is in the base station.

You can reduce the transmission power of the

handset and base station even more by using Eco Mode/Eco Mode+ (see Menu tree

◆ Eco Mode: 80% transmission power reduction

in standby mode and during a call (the range of the base station is reduced).

◆ Eco Mode+: 100% transmission power deacti-

vation in standby mode (top left display icon ½). Press and hold the talk key base station can be reached. You will hear the ringing tone if the base station can be reached. Registering handsets that do not support Eco Mode+ causes the mode to be deactivated on the base and all other handsets.

¢ page 17):

c to check that the

hours

First steps

Check the pack contents

◆ one Gigaset AS200/AS200A/AS300 base station,

◆ one mains adapter,

◆ one Gigaset AS200/AS300 handset,

◆ one phone cord,

◆ two batteries,

◆ one battery cover,

◆ one user guide.

If you have purchased a model with multiple handsets, the package should contain two batteries, a battery cover and a charging cradle with mains adapter for each additional handset.

Setting up the base station and charging cradle (if included)

The base station and charging cradle are designed for use in enclosed dry rooms with a temperature range of +5°C to +45°C.

¤ Set up the base station at a central location on a flat, non-slip surface in your house or

apartment.

Please note

Pay attention to the range of the base station. This is up to 300 m in unobstructed outdoor areas and up to 50 m inside buildings. The range is reduced when Eco Mode (

The phone's feet do not usually leave any marks on surfaces. However, due to the multitude of different varnishes and polishes used on today's furnishings, the occurrence of marks on the surfaces cannot be completely ruled out. You can also mount the base station and charging cradle on the wall.

Please note:

◆ Never expose the telephone to the influence of heat sources, direct sunlight or other elec-

trical devices.

◆ Protect your Gigaset from moisture, dust, corrosive liquids and vapours.

¢ page 17) is activated.

Connecting the base station

¤ First connect the mains adapter 1. ¤ Then connect the telephone jack 2 and

insert the cables into the cable ducts.

Please note:

◆ The mains adapter must always be con-

nected, as the phone will not operate

without mains connection.

◆ Only use the mains adapter and

phone on telephone cables can vary.

cord supplied. Pin connections

¤ Connect the flat plug from the power supply 1. ¤ Plug the mains adapter into the plug socket 2.

If you need to disconnect the plug from the charging cradle, press the release button 1 and disconnect the plug 2.

¤ Insert the batteries the right way

round. The polarity is indicated in/on the battery compartment.

¤ Slide the battery cover back into the

main casing until it clicks into place.

If you need to open the battery cover, for instance to replace the batteries, place your fingertip in the grooved area on the top of the cover and slide down.

–

Connecting the charging cradle (if included)

Setting up the handset for use

The display is protected by a plastic film.

Please remove the protective film!

Inserting the batteries and closing the battery cover

Warn ing

Use only the rechargeable batteries (¢ page 13) recommended by Gigaset Communications GmbH. Never use conventional (non-rechargeable) batteries, as this could result in significant health risks and damage to property. For example, the outer cas ing of the batteries could be destroyed or the batteries could explode. The phone could also malfunction or be damaged as a result of using batteries that are not of the recom mended type.

Registering

INT MENU

Before you can use the phone, you must first register the handset to the base station.

The handset registers automatically. Registration can take up to 5 minutes.

Do not remove the handset from the base station during this time.

After successful registration, the idle screen is displayed. Charge status of the batteries:

–

= e V U (flat to full)

–

= flashes: batteries almost flat

–

e V U flashes: charging

Put into base

¤ Place the handset with

the display facing up in the base station.

¤ Place the handset in the base station or charging cradle for eight hours. ¤ Then remove the handset from the base station or charging cradle and do

not replace it until the batteries are fully discharged.

8 h

Placing the handset in the base station and registering

If you have purchased a model with multiple handsets, repeat the registration process for each individual handset. Handsets are assigned the lowest available internal number (1–4). If

more than one handset is registered to the base station, the internal handset number appears in the top left of the display, e.g. 2. If the internal numbers 1–4 are already assigned to other devices, number

◆ Each key press interrupts the automatic registration.

◆ If automatic registration does not work, the handset will have to be registered manu-

ally (¢ page 10).

◆ Only place the handset in the base station or charging cradle that is intended for it.

Initial charging and discharging of the batteries

The correct charge level can only be displayed if the batteries are first fully charged and discharged.

4 will be overwritten.

Please note

± V

11.12. 11:56

INT MENU

Please note

◆ After the first battery charge and discharge you may replace your handset in the base

station or charging cradle after every call.

◆ Always repeat the charging and discharging procedure if you remove the batteries

from the handset and reinsert them.

◆ The batteries may warm up during charging. This is not dangerous.

◆ After a while, the charge capacity of the batteries will decrease for technical reasons.

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm can be used.

MENU ¢ Settings ¢ OK ¢ Date/Time ¢ OK ¢ Date: ¢ ~ (enter the day, month and year in 6-digit format) ¢ OK ¢ Time: ¢ ~ (enter hours and minutes in 4-digit format) ¢ OK (display message: Saved) ¢ a (press and hold to return to idle status)

Please note

When entering the time and date, you can move the position of an entr y to the left or right by pressing the control button up or down.

Display in idle status

Once the phone is registered and the time set, the idle display is shown as in this example.

If the answer machine is activated (AS200A), the answer machine icon answer machine is set with a pre-recorded announcement.

Activating/deactivating the handset

Press and hold the end call key a to activate or deactivate the handset.

If you place a deactivated handset in the base station or charging cradle, it will automatically activate.

× will be displayed in the header. Your

Your phone is now ready for use!

If you have any questions about using your phone, please read the tips on troubleshooting ("

Questions and answers" ¢ page 13) or contact our Customer Care team ¢ page 14.

Making calls

Making external calls and ending calls

External calls are calls using the public telephone network.

(Enter the phone number) ¢c.

The phone number is dialled. (Or you can first press and hold During the call you can adjust the earpiece volume using

End the call/cancel dialling:

Press the end call key a. You can automatically insert a network provider dial-

ling code before any phone number (see Menu tree "Preselection"

c [dial tone] and then enter the number.)

t and set the volume with u.

¢ page 17).

Accepting a call

The handset indicates an incoming call by ringing and by a display on the screen. Press the talk key c to accept the call.

When Auto Answer is activated (see Menu tree

¢ page 17), simply remove the handset from the

base station/charging cradle. In idle status, use t to activate the menu for setting

the call volume and use

Calling Line Identification

When you receive a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory. Requirements:

1 You have asked your network provider for the call-

er's number (CLIP) to be displayed on your handset screen.

2 The caller has asked the network provider for his

number to be identified (CLI).

not

Withhe ld appears if the caller has withheld CLI, and Unavailable appears if CLI has not been requested.

appears in the display if you have

requested Calling Line Identification,

Switch to mute

You can mute your handset when making external calls. Your caller can no longer hear you.

Press the "Microphone off" key m during the call to activate/deactivate the function.

u to set the volume.

Handsfree talking (AS300 only)

To activate while dialling:

Enter the number ~ and press the handsfree key d.

Switching between earpiece and handsfree mode:

During a call , press the handsfree key d to activate or deactivate handsfree talking. During a call, use t to activate the menu for setting the handsfree volume and use

u to set the volume.

Using the directory and lists

Last number redial list

This list contains the ten last dialled numbers.

Dialling from the last number redial list c (press briefly) ¢ u (select entry) ¢ c

Managing entries in the last number redial list c (press briefly) ¢ u (select entry) ¢ MENU

You can select the following settings:

Use Number

Copy to Dir.

Delete Entry

Delete List

Edit or add to the number. Then

dial or select other

functions from the

Copy an entry to the directory.

Delete selected entry.

Delete all entries.

MENU.

Calls list/voicemail (network mailbox) list

An advisory tone sounds and the message key flashes as soon as a new entry appears in the calls

list/voicemail list. A message appears in the display. When you press the f key, all the lists are displayed. If only one list contains new messages, this opened automatically.

Please note:

If calls are saved in the network mailbox, you will receive a message if the appropriate settings have been set (depending on your network provider).

Calls list

Precondition: CLIP (¢ page 7)

Depending on the type of list set, the calls list contains (¢ page 17)

◆ answered calls

◆ missed calls

◆ calls recorded by the answer machine

(AS200A

only)

Depending on the type of list set, all numbers of the last 25 incoming calls are saved or just the missed calls are saved.

The calls list is displayed as follows:

Number of new entries + number of old, read entries

Open the calls list

f ¢ CallsList 01+02 ¢ OK

The last incoming call is displayed. If necessary, use u to select another entry.

Using other functions

u (select entry) ¢ MENU

The following functions can be selected with u:

Delete Entry

Copy to Dir.

Date/Time

Status

Delete List

Delete current entry.

Copy an entry to the directory.

Call date and time (if set).

New Call: new missed call. Old Call: entry already read. Answ.: call taken.

Warn ing! All old and new entries

will be deleted.

will be

Calling back a caller from the calls list

f ¢ CallsList 01+02 ¢ OK ¢ u (select entry)

¢ c

+ 16 hidden pages

Siemens AS200, AS200A, AS300 Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety precautions

Care

Contact with liquid

ECO DECT

Making calls

Making external calls and ending calls

Accepting a call

Calling Line Identification

Switch to mute

Using the directory and lists

Directory

Last number redial list