User ’s Guide
UHF
The Sound of Professionals...Worldwide
Shure Brothers Incorporated
222 Hartrey Avenue, Evanston, Illinois 60202–3696 Phone: 847/866–2200 Fax: 847/866-2279
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 Internationally, Phone: 847/866–2200 Fax: 847/866-2585
27A8571 (RA) Printed in U.S.A.Copyright 1998, Shure Brothers Incorporated
ENGLISH ENGLISH
SYSTEM DESCRIPTION 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSTEM FEATURES 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSTEM COMPONENTS 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U1 BODY-P ACK TRANSMITT ER CONTROLS & INDICA T ORS 6. . . . . . . . . . . . . . . . . . . . . . .
U2 MICROPHONE-TRANSMITTER CONTROLS & INDICAT ORS 7. . . . . . . . . . . . . . . . . . . . . .
U4S & U4D RECEIVER CONTROLS & CONNECTORS 8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
RECEIVER SETUP 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Rear Mounted Receiver Antennas 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Front Mounted Receiver Antennas 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Receiver Connections 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VIEWING CURRENT RECEIVER SETTINGS 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMING THE RECEIVER 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Receiver Group/Channel Settings 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Receiver Frequency Setting 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Receiver Name 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Receiver Squelch Level Setting 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking the Receiver Display 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unlocking the Receiver Display 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMITTER SETUP 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Battery Installation 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Transmitter Batteries 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a Lavalier Microphone or Instrument Cable to the
U1 Transmitter 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMING THE TRANSMITTER 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Transmitter Group/Channel Settings 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking the Power Switch in the ON Position 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling the Power On Lock Function 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating the Frequency Lock Function 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling the Frequency Lock Function 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING THE U1 BODY–PACK SYSTEM 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING THE U2 HAND-HELD SYSTEM 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING TRANSMITTER AUDIO GAIN LEVEL 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING TRANSMITTER AUDIO INPUT LEVEL 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIPS FOR ACHIEVING OPTIMUM PERFORMANCE 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LICENSING INFORMATION 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX: NETWORK INTERFACE PIN MAP 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS
2
3
ENGLISH ENGLISH
SYSTEM DESCRIPTION
The Shure UHF Wireless microphone system is a frequency-agile diversity system operating in the UHF band. Both the receiver and the transmitter are synthesizer
controlled via Phase Locked Loop (PLL) circuitry for clear, steady radio frequency
(RF) signal. The receiver is available in either dual or single models that fit into a standard 19 inch (482 mm) equipment rack. An auxiliary unswitched AC output jack allows multiple receivers to be linked “daisy chain” style. The optional UA830 Remote
Antenna Kits can be powered by 12 Vdc, 500 mA output provided through the antenna connectors. The optional UA840 Antenna Distribution Amplifier Kits allows connection of multiple receivers using only two antennas.
U1
U2
SYSTEM FEATURES
Shure UHF Wireless Systems offer many exceptional features, including:
• Frequen cy Agility. The operating frequency of transmitters and receivers can be
easily switched to any setting in the UHF range. Settings are available in pre-programmed incremental steps that allow for necessary channel separation.
U4S
• Menu Driven Display. User–programmable receiver display shows Group,
Channel, Frequency, Name, Squelch level, and Locked/Unlocked status.
• Exclusive Shure MARCAD
Audio Diversity) circuitry constantly monitors signals from both receiver sections
and combines them in a single output signal. MARCAD provides superior reception and exceptional freedom from dropouts.
• Noise Squelch Circuitry . Analyzes signal
virtually eliminates the possibility of annoying noise bursts coming through your
receiver.
Circuitry. MARCAD (MAximum Ratio Combining
quality
instead of signal
strength
. This
U4D
• Dual RF Level Meters. The U4S and U4D receivers have two RF meters, one for
each antenna. The dual meters indicate received signal strength at each antenna,
and make it easier to identify and troubleshoot “dead spots.”
FIGURE 1
• Audio Metering. Each receiver includes a seven–segment audio meter that lets
you monitor audio level and helps optimize transmitter gain setting.
• Transmitter Display . Shows Group, Channel, Battery Power Level, and POWER
LOCK ON/OFF* condition. Both displays are user programmable.
• Transmitter Battery Power Meters: Meters on the transmitter and the RECEIV-
ER MONITOR TRANSMITTER BATTER Y POWER LEVEL from the receiver as
well as from the transmitter.
• T one Key Squelch: Eliminates unwanted noise from entering system; eliminates
popping noises when turning the transmitter on or off.
• Dual Receiver Option: Provides greater flexibility while conserving rack space.
• Preconfigured Group/Channel: Ensures frequency compatibility and simplifies
system installation.
• Network Expansion Capability. U4S and U4D receivers have a 25–pin serial con-
nector for future computer control and monitoring via an accessory interface box.
• DC/DC Converter: Ensures consistent audio and RF performance, even if bat-
tery voltages change.
* U.S. Patent No. 5,692,057.
SYSTEM COMPONENTS (FIGURE 1)
Each Shure UHF Wireless System includes the following components:
U1 Body-Pack Transmitter with your choice of instrument cable or microphone,
or
U2 Hand-Held Microphone-Transmitter with your choice of interchangeable
microphone heads:
• SM58 cardioid dynamic microphone
• BETA 58At supercardioid premium dynamic microphone
• SM87 supercardioid condenser microphone
• BETA 87
and a
U4S Single Channel Diversity Receiver with rack-mounting hardware and
antennas,
or a
supercardioid premium condenser microphone;
4
5
ENGLISH ENGLISH
13. Battery Compartment: Contains two 1.5V AA batteries (Duracell MN1500 rec-
1
2
541
3
ommended).
ON
OFF
10
11
7
6
12
13
8
9
FIGURE 2
U4D Dual Channel Diversity Receiver with rack-mounting hardware and an-
tennas.
U1 TRANSMITTER CONTROL S & INDICATORS (FIGURE 2)
1. Antenna: A flexible 1/4 wave whip antenna is permanently attached to the top of
the U1 body-pack transmitter . The antenna can be replaced in the field by a qualified technician.
2. Programmable Display: Displays group and channel, battery power level, and
frequency lock/power lock on/off status.
3. Input Connector: Provides connection with a variety of lavalier and headset microphone cables, and the Shure WA302 instrument adapter cable. LEMO–type
connectors are available as an option.
4. ON/OFF Switch: Turns transmitter power on and off.
5. On/Off LED: Glows green when the U1 is turned on.
6. Belt Clip: Allows the transmitter to be easily worn on a belt, waistband or guitar
strap.
7. MODE Button: Selects the parameter (Group or Channel) you wish to change.
8. SET Button: Changes transmitter Group and Channel settings. Also used with
the MODE button to lock power on and to lock the frequency and channel setting.
9. Audio Gain Control: Allows audio level adjustment to accommodate a variety of
sound sources (speaking, singing, or playing an instrument). A small screwdriver
is supplied for making adjustments.
10. Battery Cover Release Tabs: Squeeze these two tabs together to release the
battery cover.
11. Battery Compartment Cover: Hinged cover on front surface opens to expose
the battery and display control keys.
12. Battery Fuel Gauge: Visually indicates battery power level.
6
7
ENGLISH ENGLISH
1
1. Grille. Protects the microphone cartridge and helps reduce breath sounds and wind
noise. The grilles for the various microphone heads differ in appearance.
2
3
5
4
5
ON
OFF
6
7
8
GAIN
9
FIGURE 3
U2 TRANSMIT T ER CONTROL S & INDICATORS (FIGURE 3)
2. Programmable Display: Displays Group and Channel, battery power level, and
frequency lock/power lock on/off status.
3. Battery Fuel Gage: Visually indicates battery power level.
4. Battery Cover: Unscrews to expose batteries and display control keys.
5. ON/OFF Switch: Turns transmitter power on and off.
10
6. Antenna: Helical antenna is attached to the end of the U2 transmitter . The antenna can be replaced in the field by a qualified technician.
7. Battery Compartment: Contains two 1.5 V AA batteries (Duracell MN1500 recommended).
8. MODE Button: Selects the parameter (Group or Channel) you wish to change.
9. SET Button: Changes transmitter Group and Channel settings. Also used with
the MODE button to lock power on and to lock the frequency and channel setting.
10. Audio Gain Control: Allows audio level adjustment to accommodate a variety of
sound sources (speaking, singing, or playing an instrument). A small screwdriver
is supplied for making adjustments.
ENGLISH ENGLISH
5. Programmable Display . Displays group and channel number, frequency , squelch
level, system name, transmitter battery power level, and display lock on/off status.
6. + Button: Press this button to scroll display forward.
4
23
1
13
15
14
18
17
16
19
7
8910
6
5
11
12
15
U4S Receiver
1
4
23 6 8
13
14
5
15
1
7
18
17
16
23
4
6
5
7
8
91011
17 181619 15
12
U4D Receiver
FIGURE 4
U4S & U4D RECEIVER CONTROLS & CONNECTORS (F I G URE 4)
1. MENU Button. Press this button to access the main display menu.
2. SELECT Button. Press this button to choose or execute a displayed value or
function.
3. RF Level Indicators: Five LEDs per RF antenna channel glow to indicate RF signal strength. The more LEDs that glow, the stronger the received signal. If none
of these LEDs glow, no signal is being received
4. Audio Level Indicators: These seven LEDs glow to indicate audio signal
strength. Green indicates normal operation. Amber indicates approaching overload condition. Red indicates excessively high audio levels. (Clipping occurs
within 4–6 dB when the red LEDs glow).
7. – Button: Press this button to scroll display backward.
8. Audio Output Control: Adjusts receiver output level to match input level requirements of a mixer or amplifier . Normally, this control is set fully clockwise.
9. Headphone Monitor V olume Control: Rotate this knob to the right to increase
headphone volume; rotate it to the left to decrease headphone volume.
NOTE: If you are using a Model U4S Receiver, press the Headphone Volume
Control knob to turn the monitor on or off.
If you are using a Model U4D Receiver, press the Headphone Volume Control
knob once to select Receiver 1 or twice to select Receiver 2, depending on which
section you wish to monitor.
10. Headphone Monitor Status: These LEDs glow yellow when the headphone
monitor circuit is turned on or off.
NOTE: The T one Key feature is present only on the receiver output. As a result,
you may hear an occasional “pop” through the headphones when the transmitter
is turned on or off.
11. Headphone Input Connector: Plug headphones into this 1/4–inch connector to
monitor receiver audio.
12. POWER On/Off Switch: Turns the receiver on and off.
13. Power Input Connector: Accepts power directly from any 90 to 230 V AC, 50/60
Hz power source.
14. Power Output Connector: Provides 90 to 230 V AC, 50/60 Hz power to additional
equipment. It can be used to link multiple receivers or to power the Shure UA840
Antenna Distribution System.
15. Antenna Input Connectors: BNC-type connectors provide connection to the
supplied antennas or to coaxial cable used with a distribution amplifier or remote
antennas.
CAUTION: T o avoid damage to equipment, make sure any equipment connected
to the antenna inputs can tolerate 12 VDC power.
16. HIGH Z (Unbalanced) Output Connector: 1/4 inch phone jack provides unbalanced auxiliary level (high-impedance) output.
17. Mic/Line Slide Switch: Controls output of balanced XLR connector . It can be set
for microphone or line-level (microphone level = line level – 30 dB)).
18. LOW Z (Balanced) Output Connector: XLR connector provides balanced lowimpedance mic level or line-level output.
19. Networking Interface: 25–pin “D” connector provides future electronic interface
to computers and other equipment via accessory interface box.
8
9
ENGLISH ENGLISH
ÑÑ
ÑÑÑÑ
Ñ
ÑÑ
ÑÑÑÑÑÑ
ÑÑ
Ñ
ÑÑ
ÑÑ
ÑÑÑÑÑ
ÑÑ
ÑÑÑÑ
Ñ
ÑÑ
ÑÑÑÑÑÑ
ÑÑ
Ñ
ÑÑ
ÑÑ
ÑÑÑÑÑ
Ñ
RECEIVER SETUP
2. Connect the supplied antenna cables to the receiver and the bulkhead adapters,
as shown in Figure 7.
Installing Rear Mounted Receiver Antennas
Attach the supplied UHF antennas to the antenna BNC connectors on the receiver
back panel, as shown in Figure 5. For best performance, orient the antennas with tips
pointing away from each other at a 45° angle from vertical.
FIGURE 5
Installing Front Mounted Receiver Antennas
1. Insert the two bulkhead adapters through the larger holes on each side of the front
panel, and secure them from each side, using the supplied attaching hardware.
See Figure 6.
ANTENNA
CABLE
RECEIVER
(TOP VIEW)
ANTENNA
CABLE
FIGURE 7
NOTE: Shure recommends connecting the bulkhead adapter and antenna cables
before mounting the receiver in a rack. Once the receiver is in the rack, it is more difficult to insert the bulkhead adapters and connect the antenna cables.
3. Insert the receiver into the equipment rack and secure it with the supplied screws.
See Figure 8.
EQUIPMENT RACK
FIGURE 8
4. Attach the supplied UHF antennas to the BNC connectors on the front panel, as
shown in Figure 9. For best performance, orient the antennas with tips pointing away
from each other at a 45° angle from vertical.
10
BULKHEAD
ADAPTER
RECEIVER
(TOP VIEW)
FIGURE 6
BULKHEAD
ADAPTER
FIGURE 9
11
ENGLISH ENGLISH
Basic Receiver Connections (Figure 10)
1. Connect the receiver output to the mixer or amplifier input, using a standard audio
cable with a female 3-pin XLR connector or
2. If desired, plug a set of headphones into the headphone monitor output connector.
1
/4-inch phone plug.
3. Connect the female end of a modular power cord to the male power input connector on the rear panel of the receiver. Then plug the power cord into a suitable AC
power source.
NOTE: If the receiver is rack-mounted, or if front–mounted antennas are used,
the antennas should extend above the rack cabinet or be remotely located. Improved diversity performance may be obtained by installing one or both antennas
at a remote location and separating them by 1.5 meters (60 inches) or more. Antennas at remote locations should be connected to the receiver via UA825 or
UA850 Extension Cable Kit(s) or other suitable low-loss cable (RG8 or equivalent) and used in conjunction with a UA830 Active Remote Antenna Kit.
VIEWING CURRENT RECEIVER SETTINGS
To view current settings on the receiver display, proceed as follows:
1. Turn the receiver on by pressing upper half of the POWER switch.
HEADPHONES
2. Press either the “+” button or the “–” button on the receiver front panel to scroll
through the current settings.
PROGRAMMING THE RECEIVER
You can change the receiver Group/Channel setting, the operating frequency,
squelch level, and receiver name through the programmable display. The display
can then be locked to prevent accidental changes. Instructions for programming
each display function are presented in the following paragraphs.
Changing Receiver Group/Channel Settings
The receiver display identifies frequencies by Group and Channel. This allows
convenient setup of compatible systems. A complete list of compatible frequency
Groups and Channels is included in the separate UHF Frequency Compatibility
Guide. To change the receiver Group and Channel settings, proceed as follows:
AC POWER
1. Turn the receiver on by pressing upper half of the POWER switch.
2. Press the MENU button. The “+ MENU –” display will appear, as shown in Figure
11.
12
FIGURE 11
3. Press either the + or – button to reach the SET G/CH display , shown in Figure 12.
AUDIO MIXER
AMPLIFIER LOUDSPEAKERLOUDSPEAKER
FIGURE 12
FIGURE 10
13
ENGLISH ENGLISH
4. Press the “SELECT” button to choose Group or Channel. The current Group,
Channel, and TV channel setting will appear, as shown in Figure 13. (Models sold
outside the U.S. and Canada may not display TV channel.)
Changing Receiver Frequency Setting
1. Press the MENU button. The + MENU – display will appear, as shown in Figure 16.
GROUP
CHANNEL
TV
FIGURE 13
5. Press the SELECT button until a line is below the character you want to change,
as shown in Figure 14.
GROUP
CHANNEL
TV
FIGURE 14
6. Press either the “+” or “–” button to change the Group or Channel setting. The TV
Channel setting will change automatically. (Models sold outside the U.S. and
Canada may not display TV channel).
7. When the new Group/Channel has been completely entered, press the MENU
button. “SA VE?” will appear on the display, followed by “+ YES – NO”. Press the
“+” button to save the new Group/Channel setting or press the “–” button to return
to the original setting. See Figure 15.
FIGURE 16
2. Press either the + or – button to reach the SET FREQ display, shown in Figure 17.
FIGURE 17
3. Press the SELECT button. The current operating frequency will be displayed, as
shown in Figure 18.
FIGURE 18
4. Press the “+” or ”–” button to increase or decrease the setting in incremental steps
until the desired frequency is reached. See Figure 19.
FIGURE 15
NOTE: If more than 20 seconds of inactivity elapse, the display will return to the
original settings.
14
FIGURE 19
NOTE: The receiver operating frequency actually changes the moment you press
the + and – buttons. As the frequency changes, the G/CH number automatically
changes. By observing the RF lights on the receiver , you can see which frequencies are already being used and avoid interference. If more than 20 seconds of
inactivity elapse, the display will return to the original settings.
15
ENGLISH ENGLISH
5. Press the MENU button to enter the desired frequency , as shown in Figure 15.
SA VE? will appear on the display, followed by “+ YES – NO”. Press the “+” button
to save the new frequency, or press the “–” button to return to the original setting.
See Figure 20.
6. When the new name has been completely entered, press the MENU button.
“SA VE?” will appear , followed by “+ YES – NO”. Press the “+” button to save the
new name and return to the Group/Channel/TV display. Press the “–” button to
make more changes. See Figure 24.
FIGURE 20
Changing Receiver Name
T o identify a particular transmi tter with a receiver channel, set the name of the receiver
as follows:
1. Press the MENU button. The + MENU – display will appear, as shown in Figure 21.
FIGURE 21
2. Press either the + or – button to reach the SET NAME display , shown in Figure 22.
FIGURE 22
3. Press the SELECT button. An underline will appear under the first character of the
name. The factory pre–set Name display (SHURE) is shown in Figure 23.
FIGURE 24
NOTE: If more than 20 seconds of inactivity elapse, the display will return to the
original settings.
Changing Receiver Squelch Level Setting
Higher squelch settings will demand a quieter signal before muting the receiver,
but reduce operating range. Lower squelch settings will extend the operating range,
but increase noise levels before dropout occurs. T o change the receiver Squelch setting, proceed as follows:
1. Press the MENU button. The + MENU – display will appear, as shown in Figure 25.
FIGURE 25
2. Press either the + or – button to reach the SET SQCH display , shown in Figure 26.
FIGURE 26
3. Press the SELECT button to display the current squelch level, as shown in Figure
27 (factory preset value is “0.0”).
FIGURE 23
4. Press either the + or – button to scroll through the character options (A–Z, 1–9,
etc.) until a desired character is reached.
5. Press the SELECT button to enter the character and move to the next space. Y ou
may enter a name up to eight characters long, including blank spaces. Continue
until you have spelled out the entire name.
16
MID
FIGURE 27
4. Press either the “+” or “–” button to change the Squelch setting in increments of
0.5 until the desired level is reached. The Squelch setting actually changes the
moment you press the “+” and “–” buttons.
17
ENGLISH ENGLISH
NOTE: The highest possible squelch setting is +10.0 and the lowest possible
squelch setting is –10.0, as shown in the following table . However, the factory
preset level of 0.0 usually will not need to be changed.*
Receiver Squelch Control Settings
DISPLAY dBm*
Maximum 10 –83.0
9.5 –86.0
9.0 –87.0
8.5 –87.5
8.0 –88.0
7.5 –88.5
7.0 –89.0
6.5 –89.5
6.0 –90.0
5.5 –90.5
5.0 –91.0
4.5 –91.5
4.0 –92.0
3.5 –92.3
3.0 –92.7
2.5 –93.0
2.0 –93.3
1.5 –93.6
1.0 –93.9
0.5 –94.2
Midrange 0 –94.5
–0.5 –94.8
–1.0 –95.1
–1.5 –95.4
–2.0 –95.7
–2.5 –96.0
–3.0 –96.3
–3.5 –96.6
–4.0 –96.9
–4.5 –97.2
–5.0 –97.5
–5.5 –97.8
–6.0 –98.1
–6.5 –98.4
–7.0 –98.7
–7.5 –99.0
–8.0 –99.3
–8.5 –99.6
–9.0 –99.9
–9.5 –100.2
Minimum –10 Open
*U4S and U4D squelch values differ slightly.
Specifications subject to change without notice.
5. Once you have reached the desired squelch level, press the MENU button.
SAVE? will appear, followed by + YES – NO, as shown in Figure 28. Press the
– button to make more changes, or press + to save the new squelch setting and
return to the Group/Channel/TV display.
FIGURE 28
NOTE: If more than 20 seconds of inactivity elapse, the display will return to the
original settings.
Locking the Receiver Display
1. Press the MENU button. The + MENU – display will appear, as shown in Figure 29.
FIGURE 29
2. Press either the + or – button to reach the SET LOCK display , as shown in Figure
30.
FIGURE 30
18
19
ENGLISH ENGLISH
3. Press the SELECT button. The CODE? display will appear, as shown in Figure 31.
TRANSMITTER SETUP
Transmitter Battery Installation (Fi g ure 34)
1. Make sure the transmitter power ON/OFF switch is in the OFF position.
2. Open the transmitter battery compartment as follows:
•
FIGURE 31
4. Press +, –, +, in that order, to engage the display lock. The display shown in
Figure 32 will appear
U1 T ransmitter:
battery cover down.
•
U2 Transmitter:
Squeeze the two t abs o n eit her s ide o f th e tran smi tt er an d fli p the
Unscrew the battery cover and slide it down.
FIGURE 32
NOTE: Write down the lock code (+, –, +) and keep it in a secure place. If no code is
entered, the system will time out and return to the main display.
5. A small “lock” symbol will appear in the upper right corner of the status screen displays, as shown in Figure 33. The lock symbol indicates the receiver is in the lock
mode.
CHANNEL
GROUP
TV
FIGURE 33
Unlocking the Receiver Display
To disengage the lock, press the MENU button. When “CODE?” appears, press
+, –, + , in that order , then press the MENU button.
NOTE: Once the lock function is engaged, any attempt to change settings will
cause “CODE?” to appear. If the incorrect code is entered, “INVALID” will appear,
preventing the user from changing any settings.
1.5V AA
1.5V AA
1.5V AA1.5V AA
FIGURE 34
3. Remove the old batteries as follows:
•
U1 Transmitter:
•
U2 Transmitter:
Press down on the negative terminal end of each battery .
Lift the batteries out.
4. Install two fresh 1.5 V AA alkaline batteries (DURACELL MN1500 recommended). Make sure the battery terminals match the terminals in the transmitter.
5. Close the battery cover.
IMPORT ANT: Two fresh 1.5 V AA alkaline batteries should provide 8 to 12
hours of operation. However, nickel-cadmium (nicad) batteries may only
provide up to 3 hours of operation. Carbon-zinc and zinc-chloride batteries will not provide sufficient power, and are not recommended.
20
21
ENGLISH ENGLISH
Checking Transmitter Batteries (Figure 35)
1. Turn the transmitter power ON/OFF switch to the ON position.
2. Observe the battery fuel gauge displayed on the transmitter screen and on the
right side of the receiver screen. Battery power level is indicated by the number
of black segments displayed. As transmitter batteries are consumed, the displayed segments will gradually disappear.
NOTE: The dc to dc converter functions keeps system voltage constant as battery
voltage declines, ensuring superior audio and RF performance.
Number of
Segments Displayed on
Transmitter
5 8 – 12
4 6 – 8
3 4 – 6
2 2 – 4
1 1 or less
*Using Duracell MN1500 alkaline batteries.
TRANSMITTER BATTERY
FUEL GAUGE
(ON TRANSMITTER DISPLAY)
Number of
Segments Displayed
on Receiver
3 4 – 12
2 2 – 4
1 2 or less
0 0.5 or less
*Using Duracell MN1500 alkaline batteries.
Operating Time
Remaining
(in Hours)*
Operating Time
Remaining
(in Hours)*
Connecting a Lavalier Microphone or Instrument Cable to the U1
Transmitter (Figure 36)
1. Plug the microphone cable or instrument cable into the transmitter input connector.
2. Attach the lavalier microphone to your tie, shirt or collar. If you are using a headset,
put the headset on.
3. If an instrument adapter cable is used, attach the other end of cable to the output
connector on the instrument.
MICROPHONE CABLE OR
INSTRUMENT ADAPTER
CABLE
FIGURE 36
PROGRAMMING THE TRANSMITTER
The Group/Channel setting on the U1 and U2 transmitter display can be programmed to meet the requirements of a particular installation. Y ou can also lock the
display and the power on function to prevent accidental changes. Instructions for
programming the transmitters are presented in the following paragraphs.
Changing Transmitter Group/Channel Settings
1. Turn the transmitter on by sliding the transmitter power ON/OFF switch to the ON
position. The existing Group and Channel settings will be automatically displayed.
2. Open the battery compartment. This will expose the MODE (left) and SET (right)
buttons, as well as the GAIN control and the batteries, as shown in Figure 37.
TRANSMITTER BATTERY
FUEL GAUGE
(ON RECEIVER DISPLAY)
FIGURE 35
NOTE: If the transmitter is left on and the batteries run down, the microprocessor will
turn off RF power, the Tone key, and the display.
22
FIGURE 37
23
ENGLISH ENGLISH
3. Press and hold down the MODE button until only the Group number is displayed,
as shown in Figure 38.
5. Press the MODE button again so that only the Channel number is displayed, as
shown in Figure 40.
FIGURE 38
4. Press the SET button to increment the Group setting, as shown in Figure 39.
FIGURE 39
NOTE: If the SET button is held for more than 5 seconds, the display will go into the
fast increment mode. if more than 20 seconds of inactivity elapse, the display will
return to the original settings.
FIGURE 40
6. Press the SET button to change the Channel setting, as shown in Figure 41.
FIGURE 41
7. Press the MODE button again so that the new Group and Channel numbers are
both displayed.
NOTE: On transmitter , the transmitter operating frequency does not change until
new settings are saved.
24
25
ENGLISH ENGLISH
Locking the Power Switch in the ON Position
T o lock the power switch, press and hold the SET button, then press and hold the
MODE button. Hold both keys down until “PoL” (for power locked) is displayed, as
shown in Figure 42.
FIGURE 42
NOTE: When the Power On Lock function is activated, “–– ––” will flash on the trans-
mitter screen every 5 seconds when the transmitter power ON/OFF switch is in the
OFF position.
CANCELLING THE POWER ON LOCK FUNCTION
T o cancel the Transmitter Power On Lock unction, press and hold the SET button,
then press and hold the MODE button. Keep both keys pressed down until “Po UL”
(for power unlocked) is displayed momentarily , as shown in Figure 43.The Transmit ter Power On Lock function can also be cacelled by removing the batteries.
Activating the Frequency Lock Function
The Frequency Lock function prevents accidental frequency changes, and is particularly useful in preventing accidental or unauthorized changes. The lock function
is retained in memory , even if the transmitter is turned off and the batteries removed.
To activate the Frequency Lock function, proceed as follows:
1. Turn the transmitter power off.
2. Turn the power back on while holding down the SET button until the fuel gauge
on the transmitter is active. “Fr L” will appear momentarily, as shown in Figure 44,
until you release the SET button.
FIGURE 44
3. To verify that the frequency lock function is turned on, press the MODE or SET
button. If the lock function is turned on, “– –” will appear on the transmitter screen,
as shown in Figure 45.
26
FIGURE 43
FIGURE 45
27
ENGLISH ENGLISH
NOTE: When the Frequency Lock function is engaged, the Power On Lock function can still be activated. However, if the Power Lock and the Frequency Lock
functions are engaged, the Power Lock function must be disengaged before the
Frequency Lock can be cancelled.
Cancelling the Frequency Lock Function (Figure 46)
T o cancel the Frequency Change Lock function, repeat the steps in the preceding
Activating the Frequency Lock Functio
tion is turned off, Fr UL will appear on the transmitter display , as shown in Figure 46.
n
paragraph. When the frequency lock func-
5. Turn the receiver on by pressing the upper section of the POWER switch. The receiver display and RF LEDs will glow.
6. Make sure the transmitter and receiver are tuned to the same Group, Channel, and
Frequency . If necessary, change the settings on either the transmitter or receiver.
7. If using a headphone monitor, push the monitor knob on the receiver (U4S) or half
the way down (U4D). The headphone monitor light, located below the knob, will
glow. Rotate the knob until the headphone volume is at a comfortable level.
NOTE: If you are using the U4D receiver, pushing this knob selects the receiver
section you wish to monitor.
8. Begin speaking or playing your instrument. Rotate the OUTPUT LEVEL knob as
necessary to achieve desired receiver output levels.
NOTE: If the red PEAK LEDs on the receiver do not flicker during the loudest
sounds, or if they are always on, the transmitter gain may need to be increased or
decreased. Refer to Adjusting the T ransmitter Audio Gain Level. If the system still
does not operate properly, consult the Troubleshooting table.
9. When the performance or presentation is over, slide the transmitter ON/OFF
switch to the OFF position to conserve battery power.
OPERATING THE U2 HAND-HEL D SYSTEM
1. Slide the transmitter power ON/OFF switch to the ON position. The Group and
Channel number will appear on the transmitter display, along with a bar graph indicating battery power level.
2. Turn the receiver on by pressing the upper section of the POWER switch. The receiver display and the RF lights will glow.
FIGURE 46
OPERATING THE U1 BODY–PACK SYSTEM
1. Clip the U1 body pack transmitter to your belt, waistband, or guitar strap. Push the
body pack all the way down.
2. Connect the lavalier microphone, headset mi cr ophone, or instr ument adapter cabl e
to the U1 transmitter.
3. If you will be using a lavalier microphone, clip it to your tie, lapel, or other garment.
If you are using a headset, put the headset on. If you are using an instrument
adapter cable, plug it into the instrument.
4. Slide the transmitter power ON/OFF switch to the ON position. The green power
on LED will glow and the Group and Channel number will appear on the transmitter display , along with a bar graph that indicates battery power level.
3. Make sure the transmitter and receiver are tuned to the same Group, Channel,
and Frequency. If necessary, change the settings on the transmitter or receiver.
4. If using a headphone monitor, push the monitor knob on the receiver to turn the
monitor circuit on. The ON LED, located below the knob, will glow . Rotate the knob
until the headphone volume is at a comfortable level.
NOTE: If you are using the U4D receiver, pushing this knob selects the receiver
section you wish to monitor.
5. Begin speaking or singing into the microphone. Rotate the OUTPUT LEVEL knob
as necessary to increase or decrease receiver output levels.
NOTE: If the red PEAK LEDs on the receiver do not flicker during the loudest
sounds, or if they are always on, the transmitter gain may need to be increased or
decreased. Refer to Adjusting the T ransmitter Audio Gain Level. If the system still
does not operate properly, consult the Troubleshooting table.
6. When the performance or presentation is over, slide the transmitter power ON/
OFF switch to the OFF position to conserve battery power.
28
29
ENGLISH ENGLISH
ADJUSTING TRANSMITTER AUDIO GAIN LEVEL (FIGURE 47)
The transmitter audio gain level has been factory pre-set to provide satisfactory
output in most applications. However, for loud singers or high-output musical instruments, the preset level may be too high, as indicated by constant glow of the red audio level LED. Soft-spoken talkers or singers may find that the factory setting is too
low, as indicated by the failure of the amber audio level LED to glow at all.
T o adjust audio gain, open the battery compartment and locate the transmitter audio gain control. Use the supplied screwdriver to make adjustments.
DECREASE
GAIN
DECREASE
INCREASE
GAIN
FIGURE 47
GAIN
INCREASE
GAIN
ADJUSTING TRANSMITTER AUDIO INPUT LEVEL (FIGURE 48)
NOTE: The factory-preset (–6 dB) should match most applications. Before chang-
ing the audio input level, try adjusting the transmitter gain (see Figure 47).
The U1 body-pack transmitter has an attenuator switch that allows you to set the audio input level for dif ferent types of applications. Use one of the following three settings according to the type of input source you are using:
•
0 dB
(fully counterclockwise) is for low-output microphones, such as those in
headsets.
•
–6 dB
(center) is the factory-preset position; it should accommodate most vocal
and instrumental applications.
•
–20 dB
(fully clockwise) is for extremely high-output instruments, such as electric
guitars with active electronics.
T o change the audio input level, re-position the attenuator switch using the following
steps :
1. Remove the belt clip from the back of the transmitter by carefully prying the wire
bracket, one side at a time, from the sides of the transmitter. Removing the clip
will reveal an access hole in the back of the transmitter.
Increase
input level
Decrease
input level
Attenuator
access
S For
high
sound pressure level applications, such as loud singing or playing,
decrease audio gain level by rotating the gain control counterclockwise
(while the microphone is in use) until the red audio level LEDs on the receiver flickers during the loudest sounds.
S For
low
sound pressure level applications, such as soft singing or playing,
increase audio gain level by rotating the gain control clockwise until the red
audio level LEDs on the receiver flickers during the loudest sounds.
NOTE: For guitar applications, the minimum setting (full counterclockwise) is recommended.
If you are using the Shure WH10TQG headset, rotate the gain control to the full
clockwise position. Then, if necessary , rotate it back slightly.
30
Clip sockets
2. Use the supplied 1.6 mm (1/16 in.) flat blade screwdriver to turn the
trol fully clockwise (–20 dB), fully counterclockwise (0 dB), or center (–6 dB). In
the center detent position, the screw slot is horizontal when the transmitter is upright.
3. Readjust the
casionally at the strongest peaks during a performance (see Figure 47).
4. Orient the belt clip so that “Shure” is on the outside and toward the top (antenna
side) of the transmitter . Carefully reinsert the clip’s wire bracket, one side at a time,
into the body of the transmitter.
Gain
pot so the red “Audio” LED on the U4 receiver flickers only oc-
Attenuator
con-
31
ENGLISH ENGLISH
TIPS FOR ACHIEVING OPTIMUM PERFORMANCE
S Maintain a line-of-sight between the transmitter and receiver antennas.
Avoid placing transmitter and receiver where metal or other dense materials may be present.
S Avoid placing the receiver near computers or other RF generating equip-
ment.
S Avoid placing the receiver in the bottom of an equipment rack unless the
antennas are remotely located.
S Use the proper receiver antennas.
S Point the antenna tips away from each other at a 45° angle from vertical,
and keep them away from large metal objects.
S Maintain a distance of at least 10 ft between the transmitter and receiver to
prevent overloading the receiver.
S Do not obstruct the transmitter antennas with your hands.
S Use the proper cable when remotely locating receiver antennas. For best per-
formance, use Shure UA825 or UA850 low loss coaxial antenna cable, or 50Ω
low loss cable such as RG8.
S Use Shure UA830 Ac tive Remote Antenna Ki t for remote antenna placement.
S Mount diversity antennas at least
(60 inches) or more is preferred. This can be achieved by remote placement
of one or both antennas using Shure UA825 or UA850 low–loss coaxial
cable and a Shure UA830 Active Remote Antenna Kit. For multiple system
installations, use the Shure UA840 Antenna/Power Distribution System.
TROUBLESHOOTING
Some common problems and their solutions are identified in the table below. If you
are unable to solve a problem, contact your dealer or the Shure Service Department
at 1-800-516-2525 (7:30 am to 4:00 pm, Central Standard Time). In Europe, call
49-7131-72140; other international users call Shure in the U.S.A. at 847-866-2200.
Problem Solution
No sound; receiver
RF light(s) and
AUDIO LEDs not
glowing.
Make sure Power switches on transmitter and receiver are on.
Check transmitter Power/Battery Fuel Gauge. Replace battery if
necessary.
Make sure transmitter and receiver frequency Group/Channel settings are identical.
Check receiver squelch setting.
Check receiver antenna connection(s).
Make sure at least one antenna is in the line of sight of the transmitter. If necessary, reduce the distance between transmitter and receiver.
1
/4-wave apart, although spacing of 1.5 m
Problem Solution
No receiver sound;
RF and Audio Level
meter LEDs glowing.
Received signal is
noisy or contains
extraneous sounds
with transmitter on.
Noise from receiver with transmitter
off.
Momentary loss of
sound as transmitter is moved
around performing
area.
Turn up the receiver aud io output Level control.
Check for proper connection between receiver and microphone
mixer.
Talk into the microphone and observe the receiver audio level
LEDs. If they glow, the problem is elsewhere in the sound system.
Check transmitter Power/Battery Fuel Gauge and replace battery
if power is low.
Remove local sources of RF interference, such as lighting equipment.
If using a guitar or other instrument, make sure it is connected to
the U1 with a Shure WA302 adapter cable.
Two transmitters may be operating on the same frequency. L ocate
and turn one off or change frequency.
Signal may be too weak. Reposition antennas closer to the transmitter.
Adjust receiver squelch control.
Adjust receiver squelch control.
Remove local sources of RF interference, such as lighting equipment.
Try using another frequency .
Reposition the receiver or antennas.
Reposition receiver and perform another “walkthrough” test and
observe the RF level or Diversity signal indicators. If audio dropouts persist, mark these “dead spots” in the performing area and
avoid them during the performance.
Decrease squelch control setting, even though noise in “dead
spots” may increase slightly .
Move antennas to a remote location (use UA830 kit)
SPECIFICATIONS
Refer to the supplement that came with your system.
LICENSING INFORMATION
Changes or modifications not expressly approved by Shure Brothers Inc. could void
your authority to operate the equipment. Licensing of Shure wireless microphone equi pment is the user’s responsibility, and licen sability depends on the user ’s classification
and application, and on the selected frequency. Shure strongly urges the user to contact
the appropriate telecommunications authority concerning proper licensing, and before
choosing and ordering frequencies other than standard frequencies.
32
33
ENGLISH ENGLISH
APPENDIX: NETWORK INTERFACE PIN MAP
The U4S and U4D receivers both have a 25–pin network interface located on the
rear panel. The interface will allow future monitoring and control of all receiver functions, including audio level, RF level, and ‘’A/B” diversity indication, from a remote
location via an interface device. The table below identifies the signal output by each
pin on the connector. Contact you Shure dealer for addition information.
NOTE: Using any of the pins in the shaded area could result in system mal-
function or damage to your receiver .
Pin Receiver 1
(Left)
1 Ground Ground Not
2 Audio
Meter
3 RF Level B Analog Output 2.5 kΩ 1–4 V
4 RF Level A Analog Output 2.5 kΩ 1–4 V
5 Diversity B Analog Output 2 kΩ 1–4 V
6 Diversity A Analog Output 2 kΩ 1–4 V
7 Network In-
terrupt
8 Network In-
terrupt
9 Serial Data
Output
10 Serial Data
Input
11 5V Not
12 5V Not
13 5V
(indicates
unit is dual
channel)
14 Audio
15 RF Level B Analog Output 2.5 kΩ 1–4 V
16 RF Level A Analog Output 2.5 kΩ 1–4 V
Receiver 2
(Right)
Meter
Connection Connection
Type
Analog Output 1.2 kΩ 0–2 V
Digital Input Not
Digital Output/Busy Not
Digital Output Not
Digital Input Not
Analog Output 1.2 kΩ 0–2 V
Impedance Voltage
Range
Applicable
Typical
Maximum
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Not
Applicable
Typical
Maximum
0 V
0–5 V
1–4 V
1–4 V
1–4 V
1–4 V
5 V
5 V
1–4 V
0–5 V
Pin Receiver 1
(Left)
17 Diversity B Analog Output 2 kΩ 1–4 V
18 Diversity A Analog Output 2 kΩ 1–4 V
19 Serial Clock Digital Input Not
20 Serial Clock Digital Input Not
21 Network
22 Network
23 Serial Data
24 Serial Data
25 Ground Ground Not
Receiver 2
(Right)
Interrupt
Interrupt
Output
Input
Connection Connection
Type
Digital Input Not
Digital Output/Busy Not
Digital Output Not
Digital Input Not
Impedance Voltage
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Range
1–4 V
1–4 V
1–4 V
1–4 V
1–4 V
1–4 V
0 V
34
35
Loading...