Shure ULX-D Dual, ULX-D Quad Z16-20 User Manual

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

ULX-D Dual and Quad Z16-20

ULX-D Digital Wireless Microphone System

15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus.

16. The MAINS plug or an appliance coupler shall remain readily operable.

17. The airborne noise of the Apparatus does not exceed 70dB (A).

18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.

19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

21. Operate this product within its specified operating temperature range.

Explanation of Symbols

Caution: risk of electric shock

Caution: risk of danger (See note.)

Direct current Alternating current

On (Supply)

Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Important Product Information

LICENSING INFORMATION

Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

Information to the user

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

Stand-by

Equipment should not be disposed of in the normal waste stream

WARNING:Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting.

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Shure Incorporated

Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.

Please follow your regional recycling scheme for batteries, packaging, and electronic waste.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

WARNING:Danger of explosion if incorrect battery replaced. Operate only with AA batteries.

Note: Use only with the included power supply or a Shure-approved equivalent.

WARNING

• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate.

• Follow instructions from manufacturer

• Only use Shure charger to recharge Shure rechargeable batteries

• WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.

• Never put batteries in mouth. If swallowed, contact your physician or local poison control center

• Do not short circuit; may cause burns or catch fire

• Do not charge or use battery packs other than Shure rechargeable batteries

• Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.

• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like

Australia Warning for Wireless

This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.

WARNING:This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.

2017/06/092/45

power

n o

2DXLU

ULXD1

sync

push

control

ENTER

EXIT

SCAN

RF A B

gainaudio

sync

push

control

ENTER

EXIT

SCAN

RF A B

gainaudio

1 2

AA SB900

ULXD2

150 mA

45°

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

line

mic

ULXD4Q

Digital Wireless Receiver

push

control

ENTER

EXIT

SCAN

power

RF A B

gainaudio

RF A B

gainaudio

RF A B

gainaudio

RF A B

gainaudio

RX1 RX2 RX3 RX4

<15 cm (6 in.)

A B

gainaudio

RX1

sync

1-G: 01CH:03 TxOn 2-G: 01CH:06 TxOn 3-G: 01CH:08 TxOn 4-G: 01CH:12 TxOn

Select RX TO SCAN 1 Receiver 2 Receiver 3 Receiver

CHANNEL SCAN CROUP SCAN

GROUP SCAN

SCAN COMPLETE

GROUP:01

OPEN FREQ:70

RX CHAN FOUND: 4

Deploy Completed

4 of 4

Channels Set

SYNC TX NOW

95A29359

65A15224

EXIT

SCAN

EXIT

SCAN

EXIT

SCAN

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Quickstart Instructions

Shure Incorporated

General Description

Shure ULX-D™ Digital Wireless offers uncompromising 24-bit audio quality and RF performance, with intelligent, encryption-enabled hardware, flexible receiver options, and advanced rechargeability options for professional sound reinforcement.

A breakthrough in wireless audio quality, Shure digital processing enables ULX-D to deliver the purest reproduction of source material ever available in a wireless system, with a wide selection of trusted Shure microphones to choose from. Extended 20 Hz – 20 kHz frequency range and flat response captures every detail with clarity, presence, and incredibly accurate low end and transient response. With greater than 120 dB, ULX-D delivers wide dynamic range for excellent signalto-noise performance. Optimized for any input source, ULX-D eliminates the need for transmitter gain adjustments.

ULX-D sets a new and unprecedented standard for spectral efficiency and signal stability. The intermodulation performance of ULX-D is an incredible advancement in wireless performance, enabling a dramatic increase in the number of simultaneous active transmitters on one TV channel. Rock-solid RF signal with zero

audio artifacts extends over the entire range. For applications where secure wireless transmission is required, ULX-D offers Advanced Encryption Standard (AES) 256-bit encrypted signal for unbreakable privacy.

For scalability and modular flexibility, ULX-D receivers come in single, dual, and even quad channel versions. The dual and quad channel receivers offer conveniences such as RF cascade, internal power supply, bodypack frequency diversity, audio output channel summing, and Dante™ digital networking for multi-

3/452017/06/09

ULXD4Q

Digital Wireless Receiver

push

control

ENTER

EXIT

SCAN

power

A B

gainaudio

A B

gainaudio

A B

gainaudio

A B

gainaudio

RX1 RX2 RX3 RX4

sync

sync sync sync

SEL

SEL SEL

SEL

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Shure Incorporated

channel audio over Ethernet. All receivers offer High-Density mode for applications where high channel counts are needed, greatly increasing the amount of simultaneous channels possible over one frequency band.

Advanced Lithium-ion rechargeability provides extended transmitter battery life over alkaline batteries, battery life metering in hours and minutes accurate to within 15 minutes, and detailed tracking of battery health status.

Generations ahead of any other available system in its class, ULX-D brings a new level of performance to professional sound reinforcement.

Dual and Quad Receiver Models

The ULXD4 receiver is available in dual channel and quad channel models. Both models share the same feature set and functionality, but differ in the number of channels available and the number of audio outputs.

The descriptions and procedures in this guide are applicable to either the dual or the quad receiver.

Hardware Interface

Receiver

Front Panel

ULXD4D Dual Receiver

Supports 2 channels of wireless audio.

ULXD4Q Quad Receiver

Supports 4 channels of wireless audio.

① Infrared (IR) Sync Window

Sends IR signal to the transmitter for sync.

② Network Icon

Illuminates when the receiver is connected with other Shure devices on the network. IP Address must be valid to enable networked control.

③ Encryption Icon

Illuminates when AES-256 encryption is activated.

2017/06/094/45

7 864

4 5 4

line

mic

line

mic

line

mic

line

mic

output 1output 2output 3output 4

PrimarySecondary

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

④ LCD Panel

Displays settings and parameters.

⑤ Scan Button

Press to find the best channel or group.

⑥ Menu Navigation Buttons

Use to navigate and select parameter menus.

⑦ Control Wheel

• Push to select a channel or menu item

• Turn to scroll through menu items or to edit a parameter value

⑧ Channel Select Button

Press to select a channel.

⑨ Sync Button

Press the sync button while the receiver and transmitter IR windows are aligned to transfer settings from the receiver to the transmitter.

⑩ RF Diversity LEDs

Indicate antenna status:

• Blue = normal RF signal between the receiver and transmitter

• Red = interference detected

• Off = No RF connection between the receiver and transmitter

Shure Incorporated

Note: the receiver will not output audio unless one blue LED is illuminated.

⑪ RF Signal Strength LEDs

Indicate the RF signal strength from the transmitter:

• Amber = Normal (-90 to -70 dBm)

• Red = Overload (greater than -25 dBm)

⑫ Audio LEDs

Indicate average and peak audio levels:

DescriptionAudio Signal LevelLED

Overload/ limiter-0.1 dBFSRed (6)

-6 dBFSYellow (5) Normal peaks

-12 dBFSYellow (4)

-20 dBFSGreen (3)

-30 dBFSGreen (2)

Signal Present

-40 dBFSGreen (1)

Note: In Frequency Diversity mode, simultaneous blinking of the red and yellow audio LEDs indicates that diversity audio has been routed to this channel.

⑬ Gain Buttons

Press the ▲▼ gain buttons on the front of the receiver to incrementally adjust gain from -18 to +42 dB.

⑭ Power Switch

Powers the unit on or off.

Back Panel

① AC Power Input

IEC Connector, 100 - 240 V AC.

5/452017/06/09

1 G:01 CH:01 TxOn 2 G:01 CH:02 TxOn 3 G:01 CH:03 TxOn 4 G:01 CH:04 TxOn

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Shure Incorporated

② RF Antenna Diversity Input Jack (2)

For antenna A and antenna B.

③ RF Cascade Jack (2)

Passes the RF signal from Antenna A and Antenna B to one additional receiver.

④ Mic/Line Switch (one per channel)

Applies a 30 dB pad in mic position.

⑤ Balanced XLR Audio Output (one per channel)

Connect to a mic or line level input.

⑥ Network Status LED (Green)

One per network port.

• Off = no link

• On = network link

• Flashing = network link active

⑦ Ethernet/Dante Network Secondary Port

Connect to an Ethernet network to enable remote device control via WWB6 software. Also carries Dante digital audio and control signals for audio distribution, monitoring, and recording - see Dante Network topic.

⑧ Network Speed LED (Amber)

One per network port.

• Off = 10/100 Mbps

• On = 1 Gbps

⑨ Ethernet/Dante Network Primary Port

Receiver Home Screen

The home screen displays the following information for each receiver channel:

• Group and Channel

• Transmitter Status: NoTx or TxOn, battery icon/remaining battery life Press the SEL button to access a channel menu screen.

Transmitters

① Power LED

• Green = unit is powered on

• Red = low battery or battery error (see Troubleshooting)

• Amber = power switch is disabled

② On/Off Switch

Powers the unit on or off.

③ SMA Connector

Connection point for RF antenna.

④ LCD Display:

View menu screens and settings. Press any control button to activate the backlight.

⑤ Infrared (IR) Port

Align with the receiver IR port during an IR Sync for automated transmitter programming.

⑥ Menu Navigation Buttons

Use to navigate through parameter menus and change values.

2017/06/096/45

௠௟

௡

௪

௧

௢ ௣

௤ ௥

௦

௩

௨

௦

௥

௤

௠

௣

௢

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Shure Incorporated

exit

enter

⑦ Battery Compartment

Requires Shure SB900 rechargeable battery or 2 AA batteries.

⑧ AA Battery Adapter

• Handheld: rotate and store in the battery compartment to use a Shure SB900 battery

• Bodypack: remove to accommodate a Shure SB900 battery

⑨ Bodypack Antenna

For RF signal transmission.

⑩ Integrated Antenna

For RF signal transmission.

⑪ Microphone Cartridge

See Optional Accessories for a list of compatible cartridges.

⑫ TA4M / LEMO Input Jack

Connects to a microphone or instrument cable.

Acts as a 'back' button to return to previous menus or parameters without confirming a value change

Enters menu screens and confirms parameter changes

Use to scroll through menu screens and to change parameter values▼▲

7/452017/06/09

௟

௣ ௤

௢

௠

௢

௥

௡

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Boundary and Gooseneck Base Transmitters

Shure Incorporated

① Power Button

Press to power on; press and hold to power off.

② Mute/Active Button

Four settings are available for the mute/active button:

• Toggle: Press to switch between active and mute states

• Push-to-Mute: Hold button to mute microphone

• Push-to-Talk: Hold button to activate microphone

• Disabled: Button functionality off

③ Mute LED

Indicates whether microphone is active or muted. The following settings are available:

*MX400R series gooseneck microphones (red LED) do not offer this setting.

MutedActive

Red*Green*

OffRed

Flashing redRed

④ Low-Battery LED

• Off = More than 30 minutes of battery life remain

• On (red) = Less than 30 minutes of battery life remain

• On (green) = Microphone docked on charging station

• On (amber) = Battery is missing or is not inserted correctly

⑤ Infrared (IR) Port

Align with receiver IR port to send settings to transmitter.

⑥ Charge Connector

Connects to networked chargers and USB power supply.

⑦ Gooseneck Microphone

ULXD8 base fits 5", 10", and 15" Microflex series microphones, available in single or dualflex and with bi-color or red-only LEDs.

2017/06/098/45

Tx OVERLOAD

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

Shure Incorporated

Advanced Transmitter Features

RF MUTE

Use this to turn on a transmitter without interfering with the RF spectrum. Press and hold the exit button during power-on until RF MUTED is displayed. To un-mute, restart the transmitter.

Transmitter Input Clip

The following warning displays on the receiver LCD panel when the transmitter input is clipped:

To correct, set MIC.OFFSET to 0 dB and if necessary, attenuate the signal source. If the source cannot be attenuated while using a bodypack transmitter, select INPUT PAD from the main menu to attenuate the input signal by 12 dB.

MIC.OFFSET

MIC.OFFSET compensates for signal level differences between transmitters that share the same receiver channel.

Set the offset gain on a low signal level transmitter to match a louder transmitter: UTILITY>MIC.OFFSET Note: For normal gain adjustments, use the receiver gain buttons.

Transmitter Audio Mute Mode

Mute Mode reconfigures the transmitter power switch to act a mute switch for the audio. Using the switch, the audio can be easily turned on or muted by presenters, sports referees, or anyone who periodically needs to speak. When the audio is muted, the transmitter RF signal remains on and ready at all times.

Note: Mute Mode can be selected as an IR PRESET option.

To set a transmitter to Mute Mode:

1. From the transmitter menu: UTILITY>MUTE MODE

2. Use the arrows to select ON or OFF.

3. Press enter to save. Tip: The transmitter LED turns red when audio is muted and turns green when audio is enabled. The display of the transmitter will show AUDIO MUTED and

the receiver display will show Tx Muted. Note: Mute Mode must be set to OFF in order to use the power switch to turn off the transmitter.

Locking Controls and Settings

Use the LOCK feature to prevent accidental or unauthorized changes to the hardware.

Receiver

Menu path: DEVICE UTILITIES>LOCK

Use the control wheel to select and lock any of the following receiver functions.

• MENU: All menu paths are inaccessible

• GAIN: Gain adjustment is locked

• POWER: Power switch is disabled

• SCN/SYC: Cannot perform a Scan and Sync Tip: To unlock, press the EXIT button, turn the control wheel to select UNLOCKED, and then press ENTER to save.

Transmitter

Menu path: UTILITY>LOCK

Use the transmitter controls to select and lock any of the following transmitter functions.

9/452017/06/09

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

• MENU LOCK: All menu paths are inaccessible.

• POWER LOCK: Power switch is disabled Quick-Lock Option:To turn on the transmitter with its power and menu navigation buttons locked, press and hold the ▲ button during power-on until the locked

message is displayed. Tip: To unlock the MENU LOCK, press the ENTER button 4 times to pass through the following screens: UTILITY>LOCK>MENU UNLOCK To unlock the POWER LOCK, set the power switch to the off position, then press and hold the ▲ button while resetting the power switch to the on position.

Shure Incorporated

Home Screen Display Options

Receiver

The HOME INFO menu provides options to change the information shown on the receiver home screen:

DEVICE UTILITIES>HOME INFO

Use the control wheel to select one of the following screen displays.

Transmitter

Home Screen: Press the ▲▼ arrows at the home menu to display one of the following screens:

Menu Screens

Receiver Channel

① Receiver Information

Use DEVICE UTILITIES>HOME INFO to change the home screen display.

② Gain Setting

−18 to +42 dB, or Mute.

③ Mic. Offset Indicator

Indicates offset gain is added to the transmitter.

④ Transmitter Settings

2017/06/0910/45

[

3 4 5 6

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

The following information cycles when a transmitter is tuned to the receiver's frequency:

• Transmitter Type

• Input Pad (Bodypack only)

• RF Power Level

• Transmitter Lock Status

• Transmitter Mute Status

⑤ Battery Runtime Indicator

Shure SB900 battery: runtime is displayed in minutes remaining.

AA batteries: runtime is displayed with a 5-bar indicator.

⑥ TV Channel

Displays the TV channel that contains the tuned frequency.

⑦ High Density Mode Icon

Displayed when High Density mode is enabled.

Transmitter Status

The following text or icons report transmitter status to the receiver screen:

Transmitter StatusDisplay Icon

Bodypack input is attenuated 12 dB

Offset gain is added to the transmitter 1 mW RF power levelLo

10 mW RF power levelNm 20 mW RF power levelHi Menu is lockedM Power is lockedP Displayed when the transmitter audio is set to off using the MUTE MODE featureTxMuted No RF connection between a receiver and transmitter or transmitter OFF-No Tx-

Shure Incorporated

Transmitter

① Transmitter Information

Scroll ▲▼ at the home screen to change the display

② Power Lock Indicator

Indicates power switch is disabled

③ Transmitter Audio Muted Indicator

Displayed when the transmitter audio is set to off using the MUTE MODE feature.

④ Battery Runtime Indicator

• Shure SB900 battery: runtime is displayed in hours:minutes remaining

• AA Batteries: runtime is displayed with a 5-bar indicator

⑤ Menu Lock Indicator

Indicates menu navigation buttons are disabled

⑥ Mic. Offset

Displays microphone offset gain value

11/452017/06/09

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

⑦ RF Power

Displays RF power setting

⑧ Bodypack Input Pad

The input signal is attenuated 12 dB

⑨ Encryption Icon

Indicates encryption is enabled on the receiver and has been transferred to the transmitter from a sync

Adjusting Receiver Display Brightness and Contrast

Adjust BRIGHTNESS and CONTRAST settings to improve visibility in challenging lighting environments.

1. From the receiver menu: DEVICE UTILITIES>DISPLAY

2. Press the control wheel to select CONTRAST or BRIGHTNESS.

3. Turn the control to adjust the selected parameter.

4. Press ENTER to save changes.

Editing Receiver Channel Name

To edit a receiver channel name, choose EDIT NAME from the menu.

• Turn the control wheel to edit a highlighted character

• Press the control wheel to advance to the next character

• Press ENTER to save changes

Shure Incorporated

Note: The channel name is transferred to a transmitter during a sync.

Receiver Menu Descriptions

RADIO

Displays Group, Channel, Frequency, and TV information. Use the control wheel to edit values

Group for the selected frequency

CH:

Channel for the selected frequency

FREQUENCY

Selected frequency (MHz)

TV:

Displays the TV channel for the selected frequency

AUDIO

GAIN

Use the control wheel or gain buttons to adjust the channel gain from -18 to 42 dB, in 1 dB increments.

MUTE

Mutes the receiver audio output.

EDIT NAME

Use the control wheel to assign and edit the selected receiver channel name.

IR PRESETS

BODYPACK / HANDHELD

BP PAD

Sets the audio input attenuation options: KEEP, 0, -12.

2017/06/0912/45

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

LOCK

Sets the lock options: KEEP, Power, Menu, All, None

RF POWER

Sets the transmitter RF power level: KEEP, 10mW=Nm, 1mW=Lo, 20mW=Hi.

BATT

Sets the transmitter battery type to ensure accurate metering: KEEP, Alkaline, NiMH, Lithium

BP OFFSET

Adjustable gain to compensate for signal level difference between transmitters: KEEP, 0 to 21 dB in 3 dB increments

HH OFFSET

Adjustable gain to compensate for signal level difference between transmitters: KEEP, 0 to 21 dB in 3 dB increments

MUTE MODE

Configures the transmitter power switch to act as an audio mute switch.

Cust. Group

Create Custom Groups of up to 6 frequencies and export to networked receivers

GOOSENECK / BOUNDARY

HIGH PASS

Attenuates frequencies below 150 Hz by 12 dB per octave: KEEP, OFF, ON

Shure Incorporated

RF POWER

Sets the transmitter RF power level: KEEP, 10mW=Nm, 1mW=Lo, 20mW=Hi

BATTERY

Sets the transmitter battery type to ensure accurate metering: KEEP, Alkaline, NiMH, Lithium

BN OFFSET

Adjustable gain to compensate for signal level difference between transmitters: KEEP, 0 to 21 dB in 3 dB increments

GN OFFSET

Adjustable gain to compensate for signal level difference between transmitters: KEEP, 0 to 21 dB in 3 dB increments

POWER LOCK

Locks the transmitter's power button: KEEP, OFF, ON

Cust. Group

Create Custom Groups of up to 6 frequencies and export to networked receivers

INITIAL STATE FROM CHARGER

Choose the transmitter's state after it is removed from a charger: KEEP, Active, Muted, OFF

MUTE BUTTON BEHAVIOR

Sets the mute button behavior: KEEP, Toggle, Push-to-Talk, Push-to-Mute, Disabled

BN MUTE LED ACTIVE/MUTE

Sets the mute LED colors for active and muted states: KEEP, Green/Red, Red/OFF, Red/Flash-Red, OFF/OFF

GN MUTE LED ACTIVE/MUTE

Sets the mute LED colors for active and muted states: KEEP, Green/Red, Red/OFF, Red/Flash-Red, OFF/OFF

MUTE LED LIGHT BRIGHTNESS

Sets the mute LED brightness: KEEP, Normal, Low

13/452017/06/09

ULX-D Dual and Quad Z16-20 ULX-D® Digital Wireless Microphone System

BATTERY INFO

HEALTH

Percentage of charge capacity compared to a new battery

CHARGE

Percentage of charge capacity

CYCLES

Number of charge cycles logged by the battery

TEMP

Battery temperature: °C/°F

DEVICE UTILITIES

FREQ DIVERSITY

• OFF (default)

• 1 + 2

• 3 + 4 (quad only)

• 1 + 2 / 3 + 4 (quad only)

Shure Incorporated

AUDIO SUMMING

• OFF (default)

• 1 + 2

• 3 + 4 (quad only)

• 1 + 2 / 3 + 4 (quad only)

• 1 + 2 + 3 + 4 (quad only)

ENCRYPTION

Set encryption: ON/OFF

ADVANCED RF

• HIGH DENSITY: ON/OFF

• CUSTOM GROUPS: SETUP/EXPORT/CLEAR

• ANTENNA BIAS: ON/OFF

• SWITCH BAND (Japan AB band only)

LOCK

• MENU: LOCKED/UNLOCKED

• GAIN: LOCKED/UNLOCKED

• POWER: LOCKED/UNLOCKED

• SCN/SYC: LOCKED/UNLOCKED

HOME INFO

Select screen options for Home Menu.

DISPLAY

• CONTRAST

• BRIGHTNESS: LOW/MEDIUM/HIGH

NETWORK

• CONFIGURATION: SWITCHED/REDUNDANT AUDIO/SPLIT

• SHURE CONTROL: DEVICE ID, Network Mode, Set IP and Subnet values for Ethernet network

• DANTE: DANTE DEVICE ID, AUDIO & CNTRL, REDUNDANT AUDIO, Set IP, Subnet, Gateway and Yamaha values for Dante™ network

Note: Additional information can be accessed from the selected networking option.

TX FW UPDATE

IR DOWNLOAD, Tx Firmware Version

2017/06/0914/45

+ 31 hidden pages

Shure ULX-D Dual, ULX-D Quad Z16-20 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual