Shure UA846Z2/LC Users Manual
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for
adequate ventilation and install in accordance with the manufacturer’s
instructions.
8. DO NOT install near any heat sources such as open flames, radiators,
heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
UA846Z2
Frequency Manager
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put
objects filled with liquids, such as vases, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus
to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal
injury and/or product failure.
21. Operate this product within its specified operating temperature range.
Explanation of Symbols
Caution: risk of electric shock
Caution: risk of danger (See note.)
Direct current
Alternating current
On (Supply)
Equipment protected throughout by DOUBLE INSULATION or
REINFORCED INSULATION
13. UNPLUG this apparatus during lightning storms or when unused for long
periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
General Description
The GLX-D Frequency Manager distributes RF signal and DC power for
Shure GLXD4R receivers. The rack-mountable system increases channel
count and reduces the number of required antennas and power supplies.
When connected to the GLX-D Frequency Manager, GLXD4R receivers operate in the most spectrally efficient manner.
Features
• Improves the RF performance of connected GLXD4R receivers
• Increases channel count with more efficient frequency management
• Distributes RF signal and power to six receivers
• Cascade ports connect second frequency manager for up to 11 receivers
Stand-by
Equipment should not be disposed of in the normal waste stream
WARNING:Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. The
safety certifications do not apply when the operating voltage is changed from
the factory setting.
• Consolidates antennas and power supplies for simpler setup
• Mounts in standard 19 inch equipment racks
• Supports remote antenna placement
• All-metal construction
Included Components
• Rack-mounting hardware
• External power supply
• (6) threaded DC power cables
• (2) Reverse SMA Cable
1/7©2016 Shure Incorporated
Optional Accessories and Replacement Parts
PA805Z2-RSMAPassive Directional Antenna 2.4 GHz
UA505-RSMAWall Mount for PA805-RSMA and UA8-2.4GHZ
UA8-2.4GHZ1/2 Wave Antenna, 45 deg. (2.4 GHz)
UA802-RSMA0.6 m (2 ft.) Reverse SMA Cable
UA806-RSMA1.8 m (6 ft.) Reverse SMA Cable
UA825-RSMA7.6 m (25 ft.) Reverse SMA Cable
Front and Rear Panels
Shure IncorporatedUA846Z2 Frequency Manager
UA850-RSMA15.2 m (50 ft.) Reverse SMA Cable
UA8100-RSMA30.4 m (100 ft.) Reverse SMA Cable
PS60Power Supply
95A32436Reverse SMA Bulkhead Adapters
95W8631Nut
95X8631Washer
① Antenna A Connector
Mount antenna and connect to antenna A input on rear panel.
② Power LED
Illuminates when unit is on.
③ Power Switch
Powers the system on and off.
④ Antenna B Connector
Mount antenna and connect to antenna B input on rear panel.
⑤ Power Input
Connects to supplied external power supply.
⑥ Power Outputs
Connect to receiver power inputs.
⑦ Firmware Update (USB)
Connect to computer to download firmware updates.
⑧ RF Input Antenna B
Use reverse SMA cables to connect antenna.
2017/06/092/7
⑨ Cascade RF B Connector
Connect to second frequency manager's antenna inputs, or connect a sixth receiver.
Note: Do not use other RF outputs to connect to a second frequency manager.
⑩ RF B Connectors
Connect to receiver's antenna B input.
⑪ RF A Connectors
Connect to receiver's antenna A input.
⑫ Cascade RF A Connector
Connect to second frequency manager's antenna inputs, or connect a sixth receiver.
Note: Do not use other RF outputs to connect to a second frequency manager.
⑬ RF Input Antenna A
Use reverse SMA cables to connect antenna.
Hardware Connections
1. Connect each antenna to the antenna A and antenna B outputs on the frequency manager's rear panel.
2. If mounting in equipment rack, use included rackmount hardware to mount as shown.
3. Connect power supply to power outlet and to the power in on the frequency manager.
4. Power each receiver by connecting a DC power cable between the frequency manager's power out and the receiver's power input.
5. Use reverse SMA cables to connect the frequency manager's RF A and RF B ports to each receiver's antenna A and antenna B inputs.
Shure IncorporatedUA846Z2 Frequency Manager
Note: If mounting antennas remotely, see Remote Antenna Placement.
3/72017/06/09
Loading...