SHOWTEC LED Powerbrick Set Product Manual

LED Powerbrick Set

ORDERCODE 41322

Showtec

Showtec LED Powerbrick Set™ Product Guide

Warning..…...................................................................................…………………………………………..

Safety-instructions………………………………………………………………………………………….….

Operating Determinations……………………………………………………………………………….….

Description..…..............................................................................……….……………………………….…

Features and Overview ………………………………...….……………….………….……….……….…
Backside…………………………………………………...…...….……………….…………………...….….

Installation...............................................................................…...……………………………………..…..

Set Up and Operation.....................................................................……..…………………………….……

1) Connected separate……...........................................……..…………………………………………

2) Connected on top of eachother by using the supplied brackets..............................………..

3) Connected Side by Side...........................................……..…………………………………………..

Functions……………………………………………………………………………………………………….

Stand-alone ………………………………………………………………..……………….…….……..
Connection Stand-alone…………………………………………….………………………………..
DMX Controlled ….………………………………………………………………….…….…….…..….
Connection DMX …………..…………..………………………………………………………..…..…

Illuminance Distribution………..…………………………………………………………….…………………

Candle Power distribution.............................................................…………………….………….……

2
2
3

4
4
4

5

5
5
5
5
7

7
10
11
12

13
14

Maintenance...................................................................................………..………….…….……………..

Changing the Fuse........................................................................…………………….…………..…...

Troubleshooting............................................................................………………….………………….…..

Product Specifications.................................................................……………….…….…………………..

15
15

15

16

1

WARNING

CAUTION!

Keep this device away from rain and moisture!

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

SAFETY INSTRUCTIONS

Every person involved with the installation, operation and maintenance of this device has to:

- be qualified

- follow the instructions of this manual

CAUTION! Be careful with your operations.

With a dangerous voltage you can suffer

a dangerous electric shock when touching the wires!

Before your initial start-up, please make sure that there is no damage caused by transportation. Should there
be any, consult your dealer and do not use the device.

To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow
the safety instructions and warning notes written in this manual.

Please consider that damages caused by manual modifications to the device are not subject to warranty.

This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorized modification to the device.

• Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!

• Never remove warning or informative labels from the unit.

• Never leave any cables lying around.

• Do not insert objects into air vents.

• Do not open the device and do not modify the device.

• Do not connect this device to a dimmerpack.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Do not switch the device on and off in short intervals, as this would reduce the system’s life.

• Only use device indoor, avoid contact with water or other liquids.

• Only operate the fixture after having checked that the housing is firmly closed and all screws are

tightly fastened.

• Only operate the device after having familiarized with its functions.

• Avoid flames and do not put close to flammable liquids or gases.

• Always keep case closed while operating.

• Always allow free air space of at least 50 cm around the unit for ventilation.

• Always disconnect power from the mains, when device is not used or before cleaning! Only handle

the power-cord by the plug. Never pull out the plug by tugging the power-cord.

2

• Make sure that the device is not exposed to extreme heat, moisture or dust.

• Make sure that the available voltage is not higher than stated on the rear panel.

• Make sure that the power-cord is never crimped or damaged. Check the device and the power-

cord from time to time.

• If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.

• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.

• If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.

• The user is responsible for correct positioning and operating of the LED Powerbrick. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.

• For adult use only. The device must be installed out of the reach of children. Never leave the unit
running unattended.

• For replacement use fuses of same type and rating only.

• Repairs, servicing and electric connection must be carried out by a qualified technician.

• WARRANTY: Till one year after date of purchase.

OPERATING DETERMINATIONS

If this device is operated in any other way, than the one described in this manual, the product may suffer
damages and the warranty becomes void.

Any other operation may lead to dangers like short-circuit, burns, electric shock, lamp explosion, crash etc.

You endanger your own safety and the safety of others!

Rigging

Please follow the European and national guidelines concerning rigging, trussing and all other safety issues.

Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !

Procedure:

• If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.

• Use a clamp to mount the projector, with the mounting-bracket, to the trussing system.

• The projector must never be fixed swinging freely in the room.

• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or

safety-cable.

• When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.

Improper installation can cause serious damage to people and property !

3

Description of the device

Features

The LED Powerbrick Set is a LED system from Showtec.

• Powerbrick set contains 4 Powerbricks, one controller, power leads, DMX leads.

• Ultra bright LED

• First grade aluminum body construction

• Unlimited colors

• Low power consumption

• Low heat design, great for long time operation.

• Lifetime: 100.000 hours

NOTE: Knowledge of DMX is required to fully utilize this unit.

Overview

Backside

Fig. 2 Fig. 3

1) 3-pin DMX signal connector (OUT) 6) LCD Display

2) 3-pin DMX signal connector (IN) 7) EXIT

3) 5-pin DMX signal connector (OUT) 8) SET

4) 5-pin DMX signal connector (IN) 9) UP

5) IEC Connector + Fuse 10) DOWN

Fig. 1

4

Installation

Remove all packing materials from the LED Powerbrick Set. Check that all foam and plastic padding is
removed. Connect all cables.

Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.

Set Up and Operation

Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

Note : Link all cables before connecting electric power.

You have 3 possibilities to set up your LED Powerbrick Set:

1) Separate

2) Connected on top of eachother by using the supplied brackets

Bracket Mounting the separate Powerbricks Backside connection

3) Connected Side by Side

Be sure to put the devices next to eachother and slide Pin A1 in hole B1, do the same for pin A2 in hole B2.
Then slide the first device in the direction of C. The last step is securing the devices at the back by using clasp
D and turning it clockwise to tighten the locking mechanism.

5