LED Imagespot 75W V1
Highlit e I nternati onal B. V. – Vest ast raat 2 – 6468 EX – Kerkrade – t he Netherlands
Ordercode: 40713
MANUAL
ENGLISH
Ordercode: 40713
LED Imagespot 75W
Table of contents
Warning .......................................................................................................................................................... 2
Safety Instru ctions....................................................................................................................................... 2
Operating Determinations ......................................................................................................................... 4
Rigging ....................................................................................................................................................... 4
Connection with the mains ........................................................................................................................ 5
Return Procedure ....................................................................................................................................... 5
Claims......................................................................................................................................................... 5
Description of the device ............................................................................................................................... 6
Overview .................................................................................................................................................... 7
Installation ...................................................................................................................................................... 8
Set Up and Operation..................................................................................................................................... 8
Placing a gobo in the gobo compartment ............................................................................................... 8
Placing the framing shutters ....................................................................................................................... 9
Control Modes............................................................................................................................................ 9
One LED Imagespot 75W (Manual mode) .............................................................................................. 9
Multiple LED Im agespots 75W (DMX Control) .......................................................................................... 9
Fixture Linking ........................................................................................................................................... 10
Data Cabling ........................................................................................................................................... 10
Control Panel ........................................................................................................................................... 11
Control Mode ........................................................................................................................................... 11
DMX Addressing ....................................................................................................................................... 11
Menu Ov erview ........................................................................................................................................ 12
Main Menu Options .................................................................................................................................. 12
DMX Addressing .................................................................................................................................... 13
Manual mode........................................................................................................................................ 13
Display setting........................................................................................................................................ 13
Temperature .......................................................................................................................................... 13
Reset syst em .......................................................................................................................................... 13
Reset factory settings ............................................................................................................................ 14
Service Menu Options .............................................................................................................................. 14
Adjustment for color wheel ................................................................................................................... 14
Adjustment dimmer intensity ................................................................................................................. 14
Temperature protection setting ............................................................................................................ 14
DMX Channels .......................................................................................................................................... 15
4 channels ............................................................................................................................................. 15
Mai ntenance ................................................................................................................................................ 16
Replacing the Fuse................................................................................................................................... 16
Troubleshooting ............................................................................................................................................ 16
No Light .................................................................................................................................................... 16
No Response to DMX ................................................................................................................................ 16
Product Specifications.................................................................................................................................. 18
Dimensi ons ................................................................................................................................................... 19
Notes ............................................................................................................................................................ 20
1
Ordercode: 40713
LED Imagespot 75W
Your shipment includes:
● Showtec LED Imagespot 75W
● IEC Cable 0,9m
● 4 x framing shutters
● User manual
Warning
Unpacking Instructions
Imm ediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be dam aged from shipping or the carton
itself show s signs of mishandling. Save the carton and all packin g materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Safety Instructions
Every person inv olved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportat ion. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and w arning notes written in this manual.
Please consider that damages caused by m anual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
2
Ordercode: 40713
LED Imagespot 75W
IMPORTANT:
The manufacturer w ill not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the pow er cord come into contact with other cables! Handle the pow er cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Alw ays
hold the fixture by the transport handles.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this w ould reduce the device’s lifespan.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after hav ing familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Alw ays keep case closed while operating.
Alw ays allow free air space of at least 50 cm around the unit for v entilation.
Alw ays disconnect power from the m ains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the pow er cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel .
Make sure that the power cord is never crimped or damaged. Check the device and the pow er
cord from time to time.
If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
If device w as dropped or struck, disconnect mains power supply imm ediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation w ater might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement, use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the LED Imagespot 75W. The
manufacturer will not accept liability for dam ages caused by the misuse or incorrect installation of
this device.
This device falls under protection class I. Therefore it is essential to connect the yellow /green
conductor to earth.
Repairs, servicing and electrical connection m ust be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
3
Ordercode: 40713
LED Imagespot 75W
Operating Determinations
● This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light -output and the illuminated surface must be bigger than 0,5
meter.
● The maximum ambient temperature ta = 45°C must never be exceeded.
● The relative humidity must not exceed 50 % w ith an ambient temperature of 45° C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short -circuit, burns, electric shock, crash etc.
You endanger your own safety and t he safety of others!
Rigging
Please follow t he European and nat ional guidelines concerning rigging, trussing and all
ot her safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an aut horized dealer !
Procedure:
If the LED Im agespot 75W is lowered from the ceiling or high joists, professional trussing systems
can be used.
Use a clamp to mount the LED Imagespot 75W, with the mounting-bracket, to the trussing system.
The LED Imagespot 75W must never be fixed sw inging freely in the room.
The installation must alw ays be secured w ith a safety attachment, e.g. an appropriate safety net
or safety-cable.
When rigging, derigging or servicing the LED Im agespot 75W, alw ays make sure, that the area
below the installation place is blocked and staying in the area is forbidden.
4
Ordercode: 40713
LED Imagespot 75W
Internati onal
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Return Procedure
Improper inst allation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the pow er plug.
Always check if the right color cable is connected to the right place.
Make sure t hat the device is always connect ed properly t o t he earth!
Improper inst allation can cause serious damage t o people and propert y!
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled w ith a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a br ief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the deliv ered goods imm ediately upon delivery for any short comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation dam age has to be reported to us w i thin one day after receipt
of the delivery.
Any return shipm ent has to be made post -paid at all tim es. Return shipments must be accompanied w ith
a letter defining the reason for return shipm ent. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Com plaints against us must be made know n in writing or by fax w ithin 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Com plaints will only be considered if the client has so far com plied w ith all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
5
Ordercode: 40713
LED Imagespot 75W
Description of the device
Features
The Show tec imagespot 75W is a professional LED gobo projector w ith DMX control. It has a zoom range
from 14°-22° which is easy to set and focus w ith the adjustable optics. Together w ith the framing shutters it
is possible to precisely illum inate your desired object w ithout unwanted stray light. It has a smooth
dimming curve and 8 dichros with split function to create an extra dimension to your gobo projection. It
can be controlled by 4 DMX channels or used stand alone and set w ith the internal menu. The gobo slot
accepts standard or personalized round and square shaped gobos.
• DMX control
• Temp controlled fan
• 14° - 22° Zoom range
• Framing shutters
• Accepts round & square gobos
• Input Voltage: 100~240VAC 50/60Hz
• Fuse: F3AL/250V
• Pow er consumption: 115W @ Full Output
• Lux@2m 14°: 8790
• Lux@2m 22°: 3680
• LED Source: 1x 75W
• Control On-Board: Display for settings & manual control
• Control Protocol: DMX512
• Control Personality: 4Ch
• Dimmer: 0-100%
• Strobe: 0-20Hz
• Zoom: Manual 14° - 24°
• Inner Gobo size: 18 mm
• Outer Gobo size: 40 mm
• Max Gobo thickness: 1 mm
• Colors: 8 dichroic-filters + white
• Color functions: Split colors, Rainbow -flow effect
• Housing: Black Metal & Flame-retardant plastic
• Pow er connections: IEC in/out (max 14 links)
• Data connections: XLR 3&5p in/output
• Cooling: Forced Cooling (Fan)
• IP Rating: IP-20
• Dimensions: 385 x 260 x 285 mm (LxWxH)
• Weight: 4,5 kg
6
Ordercode: 40713
LED Imagespot 75W
Fig. 01
Overview
01) Adjustment screw + mounting bracket for Truss mounting
02) Beam adjustment slot (4x)
03) Filterframe (filter not included!!!)
04) Pow er IEC IN
05) Ground/Earth connection
06) Pow er IEC OUT (max. 14 links)
07) DMX signal connector (OUT) 5-pin
08) DMX signal connector (IN) 5-pin
09) Gobo compartment cover with fastening screw
10) Lens 1 adjustment slide
11) Lens 2 adjustment slide
12) Safety eye
13) DMX signal connector (OUT) 3-pin
14) DMX signal connector (IN) 3-pin
15) Fuse F3AL/250V
7
Ordercode: 40713
LED Imagespot 75W
Installation
Remove all packing materials from the LED Imagespot 75W. Check that all foam and plastic padding is
remov ed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power suppl y before cleani ng or servicing.
Damages caused by non-observance are not subject to war ranty.
Set Up and Operation
Follow the directions below , as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or v ice versa.
Connect the device to the main power supply.
Placing a gobo in the gobo compartment
Follow the steps below to place a gobo in the gobo compartment.
01) Loosen the gobo compartment cover screw and remove the cover.
02) Take the gobo holder out of the device.
03) Gently slide your gobo (Not included!!) into the gobo holder.
04) Take the gobo holder and place it back into the gobo compartment.
8
Ordercode: 40713
LED Imagespot 75W
There are 2 modes:
• Manual control
• DMX-512 (4 CH)
Placing the framing shutters
01) Place the framing shutter at an angle in the according slot.
02) Gently mov e the framing shutter w hile low ering it as indicated by the red arrow.
Control Modes
One LED Imagespot 75W (Manual mode)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains pow er cord into a proper electric power supply socket.
03) When the LED Imagespot 75W is not connected with a DMX cable, it functions as a stand -alone
device. Please see page 13 for more information about the Manual mode.
Multiple LED Imagespots 75W (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the LED Imagespots 75W and other devices.
04) Link the units as show n in fig. 02. Connect the first unit's DMX "out" socket w ith the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains pow er cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
9
Ordercode: 40713
LED Imagespot 75W
Multiple LED Imagespots 75W Set Up
Fig. 02
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 14 devices should be connected on one data link.
Connecting m ore than 14 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 14 fixtures
Maximum recommended number of fixtures on a Pow er link: 14 fixtures
Note : Link all cabl es before connecting electric power
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of tw o or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your ow n cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cabl es
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user w ith exceptional audio -qualities and connector m ade by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user w ith exceptional audio -qualities and connector m ade by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable w ith digital signal transmission. Or dercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m ), FL0920 (20 m).
• DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
10
Ordercode: 40713
LED Imagespot 75W
Control Panel
A) LED display
B) MENU button
C) UP button
D) DOWN button
E) ENTER button
Fig. 03
Display Off after 30 seconds
The LED Imagespot 75W can be operated with a controller in DMX mode or w ithout the controller in
stand-alone mode.
Control Mode
The fixtures are individually addressed on a data -link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller w ill display the saved DMX address, next tim e.)
DMX Addressing
The control panel on the upper side of the device allows you to assign DMX fixture addresses, which is the
first channel w ith which the LED Imagespot 75W w ill respond to the controller.
Please note, when you use the controller, the unit has 4 channels.
When using multiple LED Imagespots 75W, make sure you set the DMX addresses right.
Therefore, the DMX address of the first LED Imagespot 75W should be 1(001); the DMX address of the
second LED Imagespot 75W should be 1+4=5 (05); the DMX address of the third LED Imagespot 75W
should be 5+4=9 (009), etc. Please, be sure that you do not have any overlapping channels in order to
control each LED Imagespot 75W correctly. If two or more LED Imagespots 75W are addressed similarly,
they w ill work similarly.
Controlling:
After having addressed all LED Imagespot 75W fixtures, you may now start operating these v ia your
lighting controller.
Note: After sw itching on, the LED Imagespot 75W w ill automatically detect w hether DMX 512 data is
received or not. If not, the problem may be:
• The XLR cable from the controller is not connected w ith the input of the LED Imagespot 75W.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
When no button is pressed for 30 seconds, the display w ill turn off.
To light up the display, you have to press the MENU, ENTER, UP or DOWN button.
Once you have pressed the button, the display will light up.
11
Ordercode: 40713
LED Imagespot 75W
DMX address
Manual mode
Display setting
Temperature
Reset system
Reset factory settings
Menu Overview
Main Menu Options
12
Ordercode: 40713
LED Imagespot 75W
DMX Addr essi ng
With this menu option you can set the DMX address.
01) Press the MENU button, until the display shows .
02) You can choose 512 different DMX addresses.
03) Use the UP/DOWN buttons to select the required address from .
Manual mode
With this menu option you can choose a static color and control the settings of the color.
01) Press the MENU button, until the display shows .
02) Press the ENTER button to open this menu.
03) Scroll through this submenu w ith the UP/DOWN buttons.
04) When the display shows , you can choose one of the 18 pre-programmed colors.
05) Press the ENTER button to open this menu. Use the UP/DOWN buttons to scroll through the preset
colors .
06) Press the MENU button to return to the previous menu.
07) When the display shows you can set the speed of the color rainbow . Press the ENTER button
to open this menu and use the UP/DOWN buttons to set the speed between .
08) When the display shows you can set the intensity of the color. Press the ENTER button to open
this menu and use the UP/DOWN buttons to set the intensity between .
09) When the display shows you can set the strobe frequency. Press the ENTER button to open
this menu and use the UP/DOWN buttons to set the frequency betw een .
Display mode
With this menu option you can choose the direction of the display text.
01) Press the MENU button, until the display shows .
02) In this mode the display text will be displayed normally.
03) With the UP/DOWN buttons you can choose between .
04) If you choose and press the ENTER button the display text w ill be reversed.
Temperature
01) Press the MENU button, until the display shows .
02) Now you can see the current temperature of the LED.
Reset system
With this menu option you can reset the system after changing its settings.
01) Press the MENU button, until the display shows .
02) Press the ENTER button to confirm, the display will show .
03) The fixture will now start up with the previous settings.
13
Ordercode: 40713
LED Imagespot 75W
Color wheel adjustment from 000-255
Dimmer intensity from 000-255
Temperature protection setting
Reset factory settings
With this menu option you can reset the system to its factory default settings.
01) Press the MENU button, until the display shows .
02) Press the ENTER button to confirm, the display will show .
03) The fixture will now start up with the original factory settings.
Service Menu Options
01) To open the service menu, press and hold the MENU button for at least 10 seconds.
02) Now enter the passw ord: .
Use the UP button to scroll through 0-9 and use the DOWN button to select a digit.
03) If no button is pressed for 10 seconds the device w ill return to the main menu.
Color wheel adjustment
With this menu option you can adjust the color wheel.
01) Press the MENU button, until the display shows .
02) With the UP/DOWN buttons you can choose the adjustment between .
Dimmer intensity
With this menu option you can adjust the dimmer intensity at the start up.
01) Press the MENU button, until the display shows .
02) With the UP/DOWN buttons you can choose the dimmer intensity betw een .
03) The fixture will start up every time with the chosen dim mer intensity.
Temperature pr otection setting
With this menu option you can see the temperature protection setting.
01) Press the MENU button, until the display shows .
02) Now you can see the t emperature protection setting.
14
Ordercode: 40713
LED Imagespot 75W
Channel 1 – Master Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 – Shutter/strobe (CH1 or CH4 must be set between 001-255 )
0-3
Closed
4-7
Open
8-215
Strobe flash frequency, from slow to fast (0-20 Hz)
216-255
Open
Channel 3 – Fan speed
0-1
Automatic speed control
2-255
Speed fan from slow to fast
Channel 4 – Color wheel (CH1 must be set between 001-255 and CH2 between 004-007 or 216-255 )
0-6
White
7-13
Yellow
14-20
Pink
21-27
Green
28-34
Red
35-41
Light blue
42-48
Light green
49-55
Orange
56-63
Dark blue
64-70
Split colors White + Yellow
71-77
Split colors Yellow + Pink
78-84
Split colors Pink + Green
85-91
Split colors Green + Red
92-98
Split colors Red +Light blue
99-105
Split colors Light blue +Light green
106-112
Split colors Light green + Orange
113-119
Split colors Orange + Dark blue
120-127
Split colors Dark blue + White
128-191
Clockwise rotation (CW) color flow from slow to fast
192-255
Counterclockw ise rotation (CCW) color flow from slow to fast
DMX Channels
4 Channels
15
Ordercode: 40713
LED Imagespot 75W
Maintenance
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every four years in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any tra ces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The LED Imagespot 75W requires almost no maintenance. How ever, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Switch off the device and then w ipe the
cover w ith a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. Do not use
alcohol or solvents. The front glass panel w ill require w eekly cleaning, as smoke-fluid tends to build up
residues, reducing the light-output very quickly. Do not immerse in liquid.
Keep connections clean. Disconnect electric pow er, and then w ipe the DMX connections w ith a damp
cloth. Make sure connections are thoroughly dry before linking equipm ent or suppl ying electric pow er.
Replacing the Fuse
Pow er surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Turn the screwdriver to the left, at the
same time gently push a bit (Turn and Push). The fuse w ill come out.
03) Remove the used fuse. If brow n or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out follow ing steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse.
01) Pow er supply. Check that the unit is plugged into an appropriate power supply.
02) The LED. Return the LED Imagespot 75W to your Show tec dealer.
03) The fuse. Replace the fuse. See page 16 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the LED Im agespot 75W, as
this may dam age the unit and the w arranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card m alfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly w ith
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
16
Ordercode: 40713
LED Imagespot 75W
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No pow er to the fixture
• Check if pow er is switched on and
cables are plugged in
Primary fuse blown
• Replace fuse
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
The controller is not connected.
• Connect controller.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
• Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
Poor data quality
• Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defectiv e fixture
disturbing the link
Bad data link connection
• Inspect connections and cables.
Correct poor connections. Repair
or replace dam aged cables
Data link not terminated w ith 120
Ohm termination plug
• Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
• Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
• Bypass one fixture at a tim e until
normal operation is restored:
unplug both connectors and
connect them directly together.
• Have the defective fixture
serviced by a qualified technician
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
• Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
No light or lamp
cuts out
intermittently
Fixture is too hot
• Allow the fixture to cool dow n
• Clean the fan
• Make sure air vents in control
panel and the front lens are not
blocked
• Turn up the air conditioning
LEDs dam aged
• Disconnect the fixture and return it
to your dealer
The power supply settings do not
match local AC voltage and
frequency
• Disconnect fixture. Check settings
and correct if necessary
17
Ordercode: 40713
LED Imagespot 75W
Model:
Showtec LED Imagespot 75W
Input Voltage:
100-240 VAC, 50/60Hz
Pow er consumption:
115W @ Full Output
DMX linking:
14 pcs
Protection rate:
IP-20
Fuse:
F3AL/250V
Dimensions:
385 x 260 x 285 mm (LxWxH)
Weight:
4,50 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
4 channels
Signal input:
3-pin DMX IN & 5-pin DMX IN
Signal output:
3-pin DMX OUT & 5-pin DMX OUT
Electro-mechani cal effects:
LED Quantity:
1 x 75W
Lux @2m 14°:
8790
Lux @2m 22°:
3680
Zoom:
Manual 14° - 22°
Dimmer:
0-100%
Strobe:
0-20Hz
Housing:
Black Metal & Flame-retardant plastic
DMX-control:
via standard DMX-controller
On Board:
4-digit LED display for easy setup
Control:
Manual and DMX
Pow er Connections:
IEC in/out (max 14 links)
Data connections:
XLR 3&5 pin in/output
Cooling:
Forced Cooling (Fan)
Inner Gobo size:
18 mm
Outer Gobo size:
40mm
Max Gobo thickness:
1mm
Colors:
8 dichroic-filters + white
Color functions:
Split colors, Rainbow -flow effect
Max. ambient temperature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
1 m
Website: www .Showtec.info
Email: serv ice@highlite.nl
Product Specifications
Design and product specifications are subject to change w ithout prior notice.
18
Ordercode: 40713
LED Imagespot 75W
Dimensions
19
Ordercode: 40713
LED Imagespot 75W
Notes
20
Ordercode: 40713
LED Imagespot 75W
21
Ordercode: 40713
LED Imagespot 75W
22
©2016 Showtec
Loading...