Galactic RGB-600 Value Line V2
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 51325
MANUAL
ENGLISH
1
Ordercode: 51325
Galactic RGB-600 Value line
Table of contents
Warning ............................................................................................................................................................................... 2
Unpacking Instructions ................................................................................................................................................. 2
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Laser safety for a Class 4 Laser Product ................................................................................................................... 5
Rigging ............................................................................................................................................................................ 7
Connection with the mains......................................................................................................................................... 8
Return Procedure .......................................................................................................................................................... 8
Claims .............................................................................................................................................................................. 8
Description of the device ................................................................................................................................................. 9
Features .......................................................................................................................................................................... 9
Overview ......................................................................................................................................................................10
Backside .......................................................................................................................................................................10
Installation .........................................................................................................................................................................11
Set Up and Operation .....................................................................................................................................................11
Control Modes .............................................................................................................................................................12
One Galactic (Auto Program) ..............................................................................................................................12
One Galactic (Sound-controlled) ........................................................................................................................12
Multiple Galactics (Master/Slave Mode) ............................................................................................................13
Multiple Galactics (DMX Control) .........................................................................................................................14
Fixture Linking ...............................................................................................................................................................15
Data Cabling ...............................................................................................................................................................15
Control Panel ...............................................................................................................................................................16
Control Mode ..............................................................................................................................................................16
DMX Addressing ..........................................................................................................................................................16
Menu Overview ...........................................................................................................................................................17
Main Menu Options ....................................................................................................................................................18
1. Auto/Sound Programs ........................................................................................................................................18
2. Auto/Sound Patterns ...........................................................................................................................................18
3. Sound sensitivity ...................................................................................................................................................19
4. DMX address .........................................................................................................................................................19
5. Slave mode ...........................................................................................................................................................19
6. IR remote control mode .....................................................................................................................................19
7. Pattern mode .......................................................................................................................................................19
Remote Control ...........................................................................................................................................................20
DMX Channels .............................................................................................................................................................21
17 channels ...............................................................................................................................................................21
Patterns ..............................................................................................................................................................................23
Maintenance ....................................................................................................................................................................24
Replacing the Fuse .....................................................................................................................................................24
Troubleshooting ...............................................................................................................................................................24
No Light .........................................................................................................................................................................24
No Response to DMX..................................................................................................................................................24
Product Specifications ....................................................................................................................................................26
Dimensions ........................................................................................................................................................................27
Notes ..................................................................................................................................................................................28
2
Ordercode: 51325
Galactic RGB-600 Value line
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Showtec Galactic RGB-600 Value Line
● IEC Power cable (1,5 m)
● 2 keys for the interlock
● Remote control plug
● IR Remote control
● User manual
3
Ordercode: 51325
Galactic RGB-600 Value line
Safety Instructions
Every person involved with the installation, operation and maintenance of this device have to:
● be qualified
● follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
● Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
● Never strain the cable insert or the female part in the device. There must always be sufficient cable
going to the device. Otherwise, the cable will be damaged, which can cause serious damage.
● Never remove warning or informative labels from the unit.
● Never use anything to cover the ground contact.
● Never place any material over the lens.
● Never look directly into the light source.
● Never leave any cables lying around.
● Never use the device during thunderstorms, unplug the device immediately.
● Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
● Never aim the laser beam at people or animals!
● Never point a laser at aircraft. This is a federal offense.
● Never point un-terminated laser beams into the sky.
● Never open the laser housing. The high laser power levels inside of the protective housing can start
fires, burn skin and will cause instant eye injury.
● Do not insert objects into air vents.
● Do not connect this device to a dimmer pack.
● Do not open the device and do not modify the device.
● Do not point lasers at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser
reflections can be hazardous.
● Do not expose the output optic (aperture) to cleaning chemicals.
● Do not use the laser if the laser appears to be emitting only one or two beams.
● Do not use the laser if housing is damaged or open, or if optics appear damaged in any way.
● Do not operate laser without first reading and understanding all safety and technical data in this
manual. Never look into the laser aperture or laser beams.
● Do not switch the device on and off in short intervals, as this would reduce the device’s life.
● Do not shake the device. Avoid brute force when installing or operating the device.
4
Ordercode: 51325
Galactic RGB-600 Value line
● After set up and prior to public use, test laser to ensure proper function. Do not use the laser if any
defect is detected. Do not use, if the laser emits only one or two laser beams rather than
dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow
emission of higher laser levels.
● Only use device indoors, avoid contact with water or other liquids.
● Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to flammable liquids or gases.
● Avoid eye or skin exposure to direct or scattered radiation of class 4 laser product.
● Always check the regulations when using a class 4 laser product.
● Always check and position the laser before anybody enters the room, when the laser is facing an
area with people.
● Always keep case closed while operating.
● Always allow free air space of at least 50 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
● Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
● Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
● If the external cable is damaged, it has to be replaced by a qualified technician.
● If the lens is obviously damaged, it has to be replaced, so that its functions are not impaired due to
cracks or deep scratches.
● If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
● If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
● For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
● Never attempt to bypass the thermostatic switch or fuses.
● For replacement use fuses of same type and rating only.
● The operation of a class 4 laser show laser is only allowed if the show is controlled by a skilled and
well-trained operator familiar with the data included in this manual.
● The user is responsible for correct positioning and operating of the laser. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
● This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
● The laser will only work between 15-35ºC.
● After 3 hours working, you must shut off the laser and let the laser diode cool off for 30 minutes,
otherwise the laser may become damaged and the warranty becomes void.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
5
Ordercode: 51325
Galactic RGB-600 Value line
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
● In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
● The maximum ambient temperature ta = 35°C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 35°C.
● If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Laser safety for a Class 4 Laser Product
Class 4 is the highest and most dangerous class of laser, including all lasers that exceed the Class 3B AEL.
By definition, a class 4 laser can burn the skin or cause devastating and permanent eye damage as a
result of direct, diffuse, specular reflections or indirect beam viewing.
These lasers may ignite combustible materials, and thus may represent a fire risk.
These hazards may also apply to indirect or non-specular reflections of the beam, even from apparently
matte surfaces—meaning that great care must be taken to control the beam path.
Class 4 lasers must be equipped with a key switch and a safety interlock.
Laser light is thousands of times more concentrated than light from any other kind of light source. This
concentration of light power can cause instant eye injuries, primarily by burning the retina (the light
sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it can still
potentially injure or blind you or your audience.
Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries
can happen quicker than you can blink.
It is incorrect to think that because these laser products split the laser into hundreds of beams or the laser
beam is scanned out in high speed, that an individual laser beam is safe for eye exposure. This laser
product uses dozens of milliwatts of laser power (Class 4 levels internally). Many of the individual beams
are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This is not true. Nor, do the
laser beams always move. Since eye injuries can occur instantly, it is critical to prevent the possibility of
any direct eye exposure. According to the laser safety regulation, it is not legal to aim Class 4 lasers in
areas which people can get exposed. This is true even if it is aimed below people’s faces, such as on a
dance floor.
CAUTION! Only Laser Safety Officers who are officially certified by a regulatory body or authorized
training organization are allowed to use class 4 lasers in public. The Laser Safety Officer is responsible for
all aspects when using this laser, including following all locally applicable safety laws and regulations.
The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this laser.
CAUTION: AVOID EXPOSURE TO BEAM: Avoid direct eye contact with laser
light. Never intentionally expose your eyes or others to direct laser
radiation.
Compliance Statement
Your laser has been designed to comply with FDA and IEC Standards for its classification.
The laser is a Class 4 laser product.
6
Ordercode: 51325
Galactic RGB-600 Value line
Laser Safety and Compliance Information
The laser is manufactured to comply with the IEC 60825-1 and in accordance with U.S. Food and Drug
Administration (FDA) Standards Listed under FDA Document 21 CFR 1040 and subsequent laser notices.
Product Classification and Manufacturing Label Identification
Laser Classification
Class 4
Cooling
Cooling fans and TE Cooling
Laser medium
Wavelength 650 nm / Red (Laser Diode) ; Output >120mW
Wavelength 532 nm / Green (DPSS); Output >180mW
Wavelength 450 nm / Blue (Laser Diode) ; Output >300mW
Output
600mW
Beam Diameter
<5mm at aperture
Pulse Data All pulses
< 4Hz (>0.25sec)
Divergence (each beam)
<2 mrad
Divergence (total light)
<40 degrees
The legal requirements for using laser entertainment products vary from country to country. The user is
responsible for the legal requirements at the location/country of use.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard
“For Safe Use of Lasers”, available from www.lia.org/. Many local governments, corporations, agencies,
military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display
guidance can be obtained via the International Laser Display Association, www.ilda.com/index.htm.
CAUTION: The use of corrective eye wear or optics for viewing at distances such as telescopes or
binoculars within a distance of 100mm may pose an eye hazard.
This laser product is a Class 4 laser and has an interlocked
housing.
There are no user serviceable parts inside. Tampering or
removing warranty seals will void your products limited
warranty.
Combo label with the Product Model Number, Serial
Number, Date of Manufacturing, Laser Light Warning Label,
Warranty Void Label and Interlocked Housing Label
Proper Usage Safety and Compliance Information
7
Ordercode: 51325
Galactic RGB-600 Value line
According to FDA Regulations you should
operate this product as stated on the left.
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
● If the laser is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the laser, with the mounting-bracket, to the trussing system.
● The laser must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
a safety cable.
● When rigging, derigging or servicing the laser, always make sure that the area below the installation
is unavailable for any unauthorized persons.
The Galactic can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious damage to people and property!
8
Ordercode: 51325
Galactic RGB-600 Value line
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
9
Ordercode: 51325
Galactic RGB-600 Value line
Description of the device
Features
The Showtec Galactic RGB 600 is a laser effect with high output and great effects.
● When using multiple units together, you can make a great and cost effective beam-show
● Different auto and sound shows integrated
● Sound-controlled via built-in microphone
● Different auto and sound shows integrated
● IR Remote control
● Power Input: 100-240V AC, 50/60Hz
● Power Consumption: 20W
● Laser Class: 4
● Laser Color: Red, Yellow, Green, Blue, Purple, Cyan, White
● Laser Power: 600mW (120mW 650nm Red, 180mW 532nm Green, 300mW 450nm Blue)
● Laser modulation: TTL
● Scan Speed: 15K
● Scan Angle: +/-40˚
● Control Modes: Auto, Master/Slave, Sound, DMX-512
● Control protocol: DMX-512
● DMX channels: 17 channels
● On Board: 3-digit LED display for easy setup
● Protection rate: IP-20
● Housing: Compact strong metal housing
● Cooling: Fan/Convection
● Connections: IEC connector (IN), 3-pin XLR (IN/OUT)
● Safety Features: Key switch, Interlock
● Fuse: T1,6A/250V
● Dimensions: 205 x 250 x 190 mm (LxWxH) (incl. bracket)
● Weight: 2,5 Kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
51316 Remote Interlock
10
Ordercode: 51325
Galactic RGB-600 Value line
Overview
Fig. 01
01) Mounting bracket with inclination screws
02) Laser lens
03) Power LED indicator (Red)
04) IR remote sensor
05) Music-control LED indicator (Blue)
Backside
Fig. 02
06) Control panel + menu buttons
07) Built-in microphone
08) Cooling fan
09) Remote control plug
10) Ground/earth connection
11) IEC Power connector AC 100-240V + Fuse T1,6A/250V
12) Power switch ON/OFF
13) Safety eye
14) Interlock
15) 3-pin DMX signal connector OUT
16) 3-pin DMX signal connector IN
11
Ordercode: 51325
Galactic RGB-600 Value line
Installation
Remove all packing materials from the Galactic. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be music-controlled by its built-in
microphone.
The Interlock plug/remote plug and safety keys are included in the box.
The interlock is the “included-in-the-box” successor for the optional remote interlock (51316).
They should be kept with the Galactic laser !!!
The following safety precautions should be followed:
● The remote control plug should be placed on the backside (10) of your
Galactic laser.
● The keys should be put into the lock (15) of your Galactic laser.
Warning
If the plug is not connected, your laser will not function.
If the key is not set to ON, your laser will not function.
12
Ordercode: 51325
Galactic RGB-600 Value line
Exclusion of liability
Be aware that in some countries, there are additional regulations, regarding the use of laser devices.
Therefore, we strongly advise you to verify your national laws with your authorities: We do not take any
responsibility for eventual discrepancies, changes or adaptions regarding lawful use of laser devices.
Control Modes
There are 4 modes:
Auto Program
Sound-controlled
Master/Slave
DMX-512 (17CH)
One Galactic (Auto Program)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Galactic is not connected by a DMX-cable, it functions as a stand-alone device.
Please see page 18 for more information about the Auto built-in programs.
One Galactic (Sound-controlled)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Galactic is not connected with a DMX-cable, it functions as a stand-alone device.
Please see page 18 for more information about the Sound-controlled mode.
13
Ordercode: 51325
Galactic RGB-600 Value line
Multiple Galactics (Master/Slave Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Galactics and other devices.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in Fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third and fourth units. You can
use the same functions on the master device as described on pages 18 (Auto Program, Soundcontrolled). This means on the master device you can set your desired operation Mode and all slave
devices will react the same as the master device.
Multiple Galactics Master/Slave Set Up
Fig. 03
14
Ordercode: 51325
Galactic RGB-600 Value line
Multiple Galactics (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the Galactics and other devices.
05) Link the units as shown in Fig. 04, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Galactics DMX Set Up
Fig. 04
Note: Link all cables before connecting electric power
15
Ordercode: 51325
Galactic RGB-600 Value line
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
● DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
● DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
● DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
● DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin. Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
● DAP Audio DMX adapter: 5-pin > 3-pin. Ordercode FLA29.
● DAP Audio DMX adapter: 3-pin > 5-pin. Ordercode FLA30.
● DAP Audio DMX Terminator 3-pin. Ordercode FLA42.
● DAP Audio DMX Terminator 5-pin. Ordercode FLA43.
The Galactic RGB-600 Value Line can be operated with a controller in control mode or without the
controller in stand-alone mode.
16
Ordercode: 51325
Galactic RGB-600 Value line
Control Panel
A) LED display
B) FUNC button
C) UP button
D) DOWN button
E) ENTER button
Fig. 05
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Galactic will respond to the controller.
Please note when you use the controller, the unit has 17 channels.
When using multiple Galactics, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Galactics should be 1(001); the DMX address of the second
Galactic should be 1+17=18 (018); the DMX address of the third Galactic should be 18+17=035 (035), etc.
Please, be sure that you do not have any overlapping channels in order to control each Galactic
correctly. If two or more Galactics are addressed similarly, they will work similarly.
Controlling:
After having addressed all Galactic fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Galactic will automatically detect whether DMX-512 data is received or not.
If there is no data received, the problem may be:
● The XLR cable from the controller is not connected with the input of the Galactic.
● The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
17
Ordercode: 51325
Galactic RGB-600 Value line
Menu Overview
The Galactic RGB-600 Value Line will only show its version number at start-up !
18
Ordercode: 51325
Galactic RGB-600 Value line
Main Menu Options
Auto/Sound Programs
Auto/Sound Patterns
Sound sensitivity
DMX Address
Slave mode
IR remote control mode
Pattern mode
You can only change a certain setting when the display is blinking.
If you cannot change a certain value, please press the FUNC button once and then change the value.
1. Auto/Sound Programs
In this menu you can start several Auto or Sound-controlled programs.
01) Press the FUNC button until the display shows .
02) Press the UP/DOWN buttons to choose between 4 options:
Auto program fast
Auto program slow
Sound-controlled program slow
Sound-controlled program fast
03) Choose the desired built-in program and press the ENTER button to confirm.
04) The Galactic will immediately start the desired Auto or Sound-controlled program.
The software will now run a pre-programmed laser show.
The speed and the characteristics of the show cannot be modified in this mode.
2. Auto/Sound Patterns
In this menu you can start the Auto or Sound-controlled patterns.
01) Press the FUNC button until the display shows .
02) Press the UP/DOWN buttons to choose between 2 options:
Auto program patterns
Sound-controlled patterns
03) Choose the desired built-in program and press the ENTER button to confirm.
04) The Galactic will immediately start the desired Auto or Sound-controlled patterns.
The software will now run a pre-programmed laser show.
The speed and the characteristics of the show cannot be modified in this mode.
19
Ordercode: 51325
Galactic RGB-600 Value line
3. Sound sensitivity
In this menu you can set the sensitivity of the Sound-controlled programs.
01) Press the FUNC button until the display shows .
02) Press the UP/DOWN buttons to choose between , from low sensitivity to high
sensitivity.
03) Choose the desired sensitivity and press the ENTER button to confirm.
04) The Galactic will immediately adjust the sensitivity of the desired Sound-controlled program.
4. DMX address
In this menu you can set the DMX address.
01) Press the FUNC button until the display shows .
02) Press the UP/DOWN buttons to choose the desired DMX address, the adjustment range is between
.
03) Set the desired DMX address and press the ENTER button to confirm.
5. Slave mode
In this menu you can set the fixture as a Slave device.
01) Press the FUNC button until the display shows .
02) Press the ENTER button to confirm.
03) If the device has not been set to slave, it is automatically classified as a master device. If the device
has been set to slave, it will react the same as its master device.
6. IR remote control mode
In this menu you can activate the IR-remote mode.
01) Press the FUNC button until the display shows .
02) Press the ENTER button to confirm.
03) In any standalone mode (excepted REM and SLA), press ON/OFF for 2 seconds to activate the
remote function.
04) Please see page 20 about the functions of your remote control.
7. Pattern mode
In this menu you can set the mirror and reverse options.
01) Press the FUNC button until the display shows .
02) Press the UP/DOWN buttons to choose between 4 options:
Normal mirror mode
x-axis reverse
y-axis reverse
x-axis and y-axis reverse
03) Press the ENTER button to confirm.
20
Ordercode: 51325
Galactic RGB-600 Value line
Remote Control
Button
Function
Description
On / Off
Press the ON/OFF button for 2 seconds to activate the
different modes except the Slave mode.
Auto programs mode
Press the button to activate Auto program.
Sound-controlled Mode
Press the button to activate Sound-controlled program, if
the device receives a sound signal, the Music LED indicator
on the front will blink (Blue LED).
+ +
Sensitivity Soundcontrolled mode
Press the buttons to set the sensitivity, from low (1) to high
(9) sensitivity.
/
Pattern change
Press the buttons to show or change the 32 built-in
patterns.
Color settings
Press one of the buttons to choose the desired built-in color
of the laser.
Preset patterns
Press the buttons to choose the desired built-in pattern
(32).
Pattern switch
Press the button to switch between the current pattern
and the last chosen pattern.
Pause
Press the button to pause the current show.
21
Ordercode: 51325
Galactic RGB-600 Value line
DMX Channels
17 channels
Channel 1 – Built-in Programs/Sound controlled mode
0-20
Laser off
20-40
(auto program fast)
41-100
(auto program slow)
101-120
(sound-contolled program slow)
121-180
(sound-contolled program fast)
181-200
(auto program pattern)
201-220
(sound-contolled pattern)
221-255
DMX mode
Channel 2 – Group patterns mode (CH1 must be set between 221-255 and CH3 between 0-255 )
0-51
Group 1 patterns
52-103
Group 2 patterns
104-155
Group 3 patterns
156-207
Group 4 patterns
208-255
Group 5 patterns
Channel 3 – Individual Patterns (CH1 must be set between 221-255 and CH2 between 0-255 )
0-255
Individual patterns in a group of 16 patterns (For exact values see page 22)
Channel 4 – Colors (CH1 must be set between 221-255 )
0-7
All collors
8-15
Red
16-23
Green
24-31
Yellow
32-39
Blue
40-47
Magenta
48-55
Cyan
56-63
White
64-111
Color rolling
112-159
Color jumping
160-207
Color moving
208-255
Strobe, from slow to fast
Channel 5 – Clipping (CH1 must be set between 221-255 )
0
Full pattern without clipping
1-127
Clipping the pattern from 0-99%
128-255
Clipping speed from slow to fast
Channel 6 – Zoom (CH1 must be set between 221-255 )
0-127
Zoom from 100% – 5%
128-169
Zoom In from 100% – 5% (slow to fast)
170-209
Zoom Out from 5% - 100% (slow to fast)
210-255
Zoom In and Out from slow to fast
22
Ordercode: 51325
Galactic RGB-600 Value line
Channel 7 – Zoom speed (CH1 must be set between 221-255 )
0-255
Zoom from fast to slow
Channel 8 – Y-axis Rolling (CH1 must be set between 221-255 )
0-127
0-359 degree fixed Y-Axis rolling
128-191
Clockwise rolling from slow to fast
192-255
Counterclockwise rolling from slow to fast
Channel 9 Y-axis rolling speed (CH1 must be set between 221-255 )
0-255
Rolling speed from fast to slow
Channel 10 – X-axis Rolling (CH1 must be set between 221-255 )
0-127
0-359 degree fixed X-Axis rolling
128-191
Clockwise rolling from slow to fast
192-255
Counterclockwise rolling from slow to fast
Channel 11 X-axis rolling speed (CH1 must be set between 221-255 )
0-255
Rolling speed from fast to slow
Channel 12 – Z-axis Rolling (CH1 must be set between 221-255 )
0-127
0-359 degree fixed Z-Axis rolling
128-191
Clockwise rolling from slow to fast
192-255
Counterclockwise rolling from slow to fast
Channel 13 Z-axis rolling speed (CH1 must be set between 221-255 )
0-255
Rolling speed from fast to slow
Channel 14 – X-axis Moving (CH1 must be set between 221-255 )
0-127
128 different positions fixed X-Axis
128-191
Clockwise moving from slow to fast
192-255
Counterclockwise moving from slow to fast
Channel 15 X-axis moving speed (CH1 must be set between 221-255 )
0-255
Moving speed from fast to slow
Channel 16 – Y-axis Moving (CH1 must be set between 221-255 )
0-127
128 different positions fixed Y-Axis
128-191
Clockwise moving from slow to fast
192-255
Counterclockwise moving from slow to fast
Channel 17 Y-axis moving speed (CH1 must be set between 221-255 )
0-255
Moving speed from fast to slow
23
Ordercode: 51325
Galactic RGB-600 Value line
Patterns
Group
1 2 3 4 5
DMX channels
0-15
16-31
32-47
48-63
64-79
80-95
96-111
112-127
128-143
144-159
160-175
176-191
192-207
208-223
224-239
240-255
24
Ordercode: 51325
Galactic RGB-600 Value line
Maintenance
The Showtec Galactic requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced.
Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass
panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents. The front glass panel will
require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light-output very quickly.
Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below.
01) Unplug the unit from electric power source.
02) Insert a screwdriver into the slot in the fuse cover. Gently pry up the fuse cover. The fuse will come
out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to
use a fuse of the same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the laser, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The laser. Return the Galactic to your Showtec dealer.
03) The fuse. Replace the fuse. See page 24 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Galactic, as this may
damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card
malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
25
Ordercode: 51325
Galactic RGB-600 Value line
Problem
Probable cause(s)
Remedy
One or more
fixtures do not
function at all
No power to the fixture
● Check that power is switched on and
cables are plugged in
Primary fuse blown
● Replace fuse
Fixtures reset
correctly, but all
respond erratically
or not at all to the
controller
The controller is not connected
● Connect controller
3-pin XLR Out of the controller does
not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
● Install a phase reversing cable
between the controller and the first
fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not at
all to the controller
Poor data quality
● Check data quality. If much lower than
100 percent, the problem may be a
bad data link connection, poor quality
or broken cables, missing termination
plug, or a defective fixture disturbing
the link
Bad data link connection
● Inspect connections and cables.
Correct poor connections. Repair or
replace damaged cables.
Data link not terminated with 120
Ohm termination plug
● Insert termination plug in output jack of
the last fixture on the link
Incorrect addressing of the fixtures
● Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
● Bypass one fixture at a time until
normal operation is regained: unplug
both connectors and connect them
directly together
● Have the defective fixture serviced by
a qualified technician
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
● Install a phase-reversing cable
between the fixtures or swap pin 2 and
3 in the fixture, that behaves erratically
Shutter closes
suddenly
The laser diode has lost its index
position and the fixture is resetting
the effect
● Contact a technician for servicing the
problem persists
No light or laser
cuts out
intermittently
Fixture is too hot
● Allow fixture to cool
● Make sure air vents at control panel
and front lens are not blocked
● Turn up the air conditioning
Laser damaged
● Disconnect fixture and return to your
dealer
The power supply settings do not
match local AC voltage and
frequency
● Disconnect fixture. Check settings and
correct if necessary
26
Ordercode: 51325
Galactic RGB-600 Value line
Product Specifications
Model:
Galactic RGB-600 Value Line
Input Voltage:
100-240V AC, 50/60Hz
Continuous Power:
20W
Fuse:
T1,6A/250V
Dimensions:
205 x 250 x 190 mm (LxWxH) (incl. bracket)
Weight:
2,5 kg
Operation and Programming
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Channels:
17 channels
Signal input:
3-pin DMX IN
Signal output:
3-pin DMX OUT
Electro-mechanical effects
Laser Class:
4
Laser Power:
600mW (120mW 650nm Red, 180mW 532nm
Green, 300mW 450nm Blue)
Laser Color:
Red, Green and Blue
Beam diameter:
<5mm at aperture
Pulse Data:
<4Hz (>0.25 sec)
Divergence (each beam):
<12 mrad;
Divergence (total light):
<40 degrees
Laser modulation:
TTL
Scan Speed:
15K
Scan Angle:
+/-40˚
Safety Features:
Key switch, Interlock
Laser Safety:
EN/IEC 60825-1 Ed 2, 2007-03
On Board:
3-digit LED display for easy setup
Control Modes:
Auto, Master/Slave, Sound, DMX-512
Control protocol:
DMX-512
Cooling:
Fan/Convection
Housing:
Compact strong metal housing
Protection rate:
IP-20
Connections:
IEC connector (IN), 3-pin XLR (IN/OUT)
Max. ambient temperature ta:
35°C
Minimum distance:
Minimum distance from flammable surfaces:
0.5m
Minimum distance to lighted object:
1m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: service@highlite.com
27
Ordercode: 51325
Galactic RGB-600 Value line
Dimensions
28
Ordercode: 51325
Galactic RGB-600 Value line
Notes
29
Ordercode: 51325
Galactic RGB-600 Value line
30
Ordercode: 51325
Galactic RGB-600 Value line
©2018 Showtec
Loading...