Shindaiwa EB212, 82051 User Manual

English................1

Spanish.........SP_1

French..........FR_1

SHINDAIWA OWNER’S/OPERATOR’S MANUAL

EB212 BLOWER

WARNING!

Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.

Part Number 82051 Rev. 6/08

English

IntroductIon

The Shindaiwa EB212 Blower is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety, or durability. Shindaiwa high performance engines represent the leading edge of 2-cycle engine technology, and deliver exceptionally high power at remarkably low displacement and weight. As a professional owner/operator, you’ll soon discover why Shindaiwa is simply in a class by itself.

the operator’s manual

Read and understand this manual before operation. Keep it in a safe

place for future reference. It contains specications and information

for operation, starting, stopping, maintenance, storage and assembly

specic to this product.

table of contents

Introduction ................................................................2

- The Operator's Manual .......................................2

Safety .........................................................................3

- Manual Safety Symbols and Important

Information .........................................................3

- International Symbols .........................................3

- Personal Condition and Safety Equipment .........3

- Equipment Check ................................................6

Emission Control .......................................................6

Description .................................................................7

Contents .....................................................................8

Assembly....................................................................9

- Blower Application .............................................9

Operation ....................................................................9

- Fuel .....................................................................9

- Starting Cold Engine .........................................11

- Starting Warm Engine .......................................12

- Stopping Engine ................................................12

- Operating Blower ..............................................13

Maintenance

- Skill Levels .......................................................14

- Maintenance Intervals .......................................14

- Air Filter ...........................................................15

- Fuel Filter ..........................................................15

- Spark Plug .........................................................16

- Cooling System .................................................16

- Exhaust System .................................................17

- Carburetor Adjustment ......................................18

Troubleshooting .......................................................19

Storage .....................................................................20

Specications ...........................................................21

Emissions Statement ................................................22

IMPORTANT

The information contained in these instructions describes units available at the time of publication.

Shindaiwa Inc. reserves the right to make changes to products without prior notice, and without obligation to make alterations to units previously manufactured.

.............................................................14

safety

manual safety symbols and Important InformatIon

Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages preceded

by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

English

DANGER

The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.

WARNING

The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided.

CAUTION

The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided.

InternatIonal symbols

Symbol form/shape

Symbol

description/application

Read and understand

Operator's Manual.

Symbol form/shape

Symbol

description/application

Fuel and oil mixture

CIRCLE AND SLASH SyMbOL

This symbol means the specic action

shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.

NOTE

This enclosed message provides tips for use, care and maintenance of the unit.

IMPORTANT

The enclosed message provides information necessary for the protection of the unit.

Symbol form/shape

Symbol

description/application

Emergency stop

Symbol form/shape

Symbol

description/application

Ignition ON/OFF

Wear eyes, ears and

head protection

Hot

Surface

Safety/Alert

DO NOT allow

ames or sparks

near fuel.

Finger Severing

Wear hand

protection. Use

two handed.

Wear slip resis-

tant foot wear.

DO NOT smoke

near fuel.

Carburetor adjustment

- Low speed mixture

Carburetor adjustment

- Idle speed

Choke Control

"Cold Start"

Position

(Choke Closed)

Primer

Carburetor adjustment

- High speed mixture

Choke Control

(Choke Open)

personal condItIon and safety equIpment

WARNING

Blower users risk injury to themselves and others if the Blower is used improperly or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a blower.

bulb

"Run"

Position

English

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.

Hand Protection

Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Gloves also reduce the transmission of machine vibration to your hands.

Breathing Protection

Wear a facemask to protect against dust.

Hearing Protection

Shindaiwa recommends wearing hearing protection whenever unit is used.

Proper Clothing

Wear snug tting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARVES, and JEWELRY.

Wear sturdy work shoes with nonskid soles:

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

Keep long hair away from engine and blower intake. Retain hair with cap or net.

Hot Humid Weather

Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals, may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-

sations, followed by loss of color and numbness in the ngers. The following precautions are strongly recommended,

because the minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands, and wrists.

• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to ll each day with jobs where

operating the unit or other hand-held power equipment is not required.

• If you experience discomfort, redness, and swelling of the ngers

followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the ngers, hands, arms, and shoulders may cause soreness,

swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist position. Also, when grasping,

use your whole hand, not just the thumb and index nger

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive movement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doc-

tor if you feel tingling, numbness, or pain in the ngers, hands,

wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented.

English

WARNING

Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.

Read the Manuals

• Provide all users of this equipment with the Operator’s Manual

and Safety Manual for instructions on Safe Operation.

Clear the Work Area

• Spectators and fellow workers must be warned, and children and

animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use.

• Take wind conditions into account: avoid open doors and win-

dows.

• Do not point blower at people or animals.

Keep a Firm Grip

• Hold the front and rear handles with both hands, with thumbs

and ngers encircling the handles.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slip-

pery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach.

Avoid Hot Surfaces

• Keep exhaust area clear of ammable debris. Avoid contact dur-

ing and immediately after operation.

English

equIpment check

WARNING

Use only Shindaiwa approved attachments. Serious injury may result from the use of a non-approved attachment combination. Shindaiwa, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by Shindaiwa. Read and comply with all safety instructions listed in this manual and safety manual.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.

• Do not use blower if any part is missing or damaged.

• Have repairs done only by an authorized Shindaiwa Service dealer.

• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.

emIssIon control

EPA Phase 2/ C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modication and 3-way Catalyst) and for the fuel tank the

Control System is EVAP (Evaporative Emissions). Evaporative emission may be applicable to California models only.

Important enGIne InformatIon

enGIne famIly: 7ehXs.0214ekG dIsplacement: 21.2 cc emIssIon complIance perIod : 300 hrs. thIs enGIne meets u.s. epa ph2 eXh and 2007 and later calIfornIa eXh and eVap emIssIon reGulatIons for s.o.r.e.. refer to oWner's manual for maIntenance specIfIcatIons and adJustments.

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY; information on label varies by

engine FAMILY).

PRODUCT EMISSION DURABILITY

The 300 hour emission durability period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.

descrIptIon

Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your Shindaiwa dealer.

Hot Decal (near mufer)

English

General Warning Decal (located on top of blower housing)

Sound Label (located on blower housing)

65 Category I

db(A)

Measured at 50 ft. (15m) per ANSI b175.2

English

STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop.

THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for

2. best operating technique.

SPARK PLUG - Provides spark to ignite fuel mixture.

SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The mufer or catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the mufer. Keep exhaust area clear of ammable debris.

RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and rmly.

engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.

FUEL TANK CAP - Covers and seals fuel tank.

AIR CLEANER - Contains replaceable air lter element.

THROTTLE POSITION LEVER - Pull back to increase engine speed. Friction washers maintain throttle lever setting.

PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the

carburetor. Pump purge bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump purge bulb an

additional 4 or 5 times.

10.

CHOKE - Choke is located on the side of the air cleaner. Move choke lever to "COLD START" ( cold starting. Move choke lever to "RUN" ( ) position to open choke.

BLOWER PIPES - Twist lock design.

11.

) to close choke for

When

contents

1 - Power Head 1 - Blower Pipe Assembly 1 - Operator's Manual 1 - Warranty Registration Card

assembly

WARNING

Never perform maintenance or assembly procedures with engine running or serious personal injury may result.

bloWer applIcatIon

Install Blower Pipes

Align grooves in straight pipe with pegs on blower housing and slide pipe onto housing.

Turn straight pipe clockwise to lock into place.

Align grooves in fan head nozzle with pegs on straight pipe and slide fan head nozzle onto straight pipe.

Turn fan head nozzle clockwise to lock into place.

English

operatIon

NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual.

fuel

WARNING

Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.

English

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved.

IMPORTANT

Mix only enough fuel for your immediate needs! If fuel must be stored longer than 30 days and oil with fuel

stabilizer is not used, it should rst be treated with a fuel stabilizer such as STA-BIL™.

is recommended for use in all Shindaiwa low emissions engines.Shindaiwa One also includes a fuel stabilizer.

Oil is a registered JASO FC classied oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One

Handling Fuel

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing

or handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow ames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps

slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors

over bare ground.

• DO NOT overll fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refu-

eling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or

operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting

the engine.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building,

away from sparks and ames.

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.

Mixing Instructions

Fill an approved fuel container with half of the required amount of

1. gasoline.

Add the proper amount of 2-stroke oil to gasoline.

2. Close container and shake to mix oil with gasoline.

3. Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.

IMPORTANT

Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.

Fuel to Oil Mix-50:1 Ratio

U.S.

GAS OIL GAS OIL

Gallons Fl.oz. Liter cc.

1 2.6 4 80 2 5.2 8 160 5 13 20 400

METRIC

startInG cold enGIne

• Provide all operators of this equipment with the Operator's Manual and instructions for safe operation.

• Before starting the unit, equip yourself and any other person working within the 15 m (50 ft.) Safety Zone with the required Protective Equipment and clothing.

Stop Switch Move stop switch button (A) away from the STOP position.

English

Throttle Position

Move throttle position lever (B) midway between idle and full throttle positions.

Choke

Move choke (C) to "Cold Start" ( ) Position.

Purge Bulb

Pump purge bulb (D) until fuel is visible and ows freely in the clear

fuel tank return line. Pump bulb an additional 4 or 5 times.

IMPORTANT

Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.

Do not allow the rope to snap back in. Always hold the unit rmly.

Recoil Starter

Place the unit on a at, clear area. Firmly grasp throttle grip with left hand and rapidly pull recoil starter handle/rope (E) until engine res (5

pulls maximum).

Choke

After engine res (or 5 pulls), move choke lever to “Run” (

tion and pull starter handle/rope until engine starts and runs. Allow unit to warm up at idle for several minutes.

) posi-

NOTE

If engine does not start with choke in “Run” position after 5 pulls,

repeat instructions 2- 5.

After engine warm up, gradually depress throttle trigger to increase

engine RPM to operating speed.

English

startInG Warm enGIne

The starting procedure is the same as Cold Start except DO NOT close the choke.

Stop Switch

1. Move stop switch button (A) away from the STOP position.

Throttle Position

2. Move throttle position lever (B) midway between idle and full throttle positions.

Recoil Starter

Place the unit on a at clear area. Firmly grasp throttle grip with left hand and rapidly pull recoil starter handle/rope (E) until engine res.

IMPORTANT

Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.

Do not allow the rope to snap back in. Always hold the unit rmly.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

stoppInG enGIne

Throttle Trigger/Throttle Position Lever

1. Release throttle trigger (F). Move throttle position lever (B) forward to idle position and allow engine to return to idle before shutting engine off.

Stop Switch

2. Move stop switch (B) to "Stop" position.

WARNING

If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your Shindaiwa dealer repair stop switch before using blower again.

operatInG bloWer

WARNING

Always wear safety glasses, hearing protection and a face lter

mask or serious personal injury may result. .

Do not point the blower pipe in the direction of people or pets.

Read the Safety Section carefully.

IMPORTANT

To avoid engine damage due to over-revving, do not block blower pipe.

Use only during appropriate hours.

Allow the engine to warm up at a fast idle for a few minutes.

Control engine speed with throttle trigger (A), or for continuous use,

3. set engine speed with throttle position lever (B). Rotate throttle position

lever forward for lower speed; back for higher speed.

English

Use lower speed to blow debris from hard surfaces.

Additional speed may be necessary to clean debris, snow, etc. from

lawns and ower beds.

NOTE

Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the blower noise. Minimize dust by using blower at lower speeds. Keep debris on your property. Be Smart - be a good neighbor.

English

/TNENOPMOC

METSYS

ECNANETNIAM

ERUDECORP

D'QER LLIKS

LEVEL

YLIAD

EROFEB

ESU

YREVE

LEUFER

SHTNOM

09RO

SRUOH

SHTNOM 072RO SRUOH

YLRAEY

serudecorPecnanetniaMrelaeDindaiwahSdednemmoceR

troPtsuahxErednilyC nobraceD/naelC/tcepsnI 3 C/I

serudecorPecnanetniaMflesruoY-tI-oD

retliFriA ecalpeR/naelC/tcepsnI 1 C/I *R

ekohC naelC/tcepsnI 2 C/I

retliFleuF ecalpeR/tcepsnI 1 I *R

skaeL,metsySleuF ecalpeR/tcepsnI 1 )1(I *)1(R/I

metsySgnilooC naelC/tcepsnI 2 C/I

rotserrAkrapSrelffuM ecalpeR/tcepsnI 2 *R/I

epoRretratSlioceR naelC/tcepsnI 1 C/I *R/I

gulPkrapS naelC/tcepsnI 2 C/I *R

stloB/stuN/swercS ecalpeR/nethgiT/tcepsnI 1 *R/I

SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:

-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxerdnaesulautcA.mumixameranwohsslavretniemiT

.ecnanetniam

:SETONERUDECORPECNANETNIAM

)1( .ytirgetninoissimeniatniamotecnanetniamralugereriuqerTONODsknatleufevitaropavewoL

* .noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA

maIntenance

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.

IMPORTANT

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL, HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM

skIll leVels

Level 1 = Easy to do. Most required tools come with unit. Level 2 = Moderate difculty. Some specialized tools may be required. Level 3 = Experience required. Specialized tools are required. Shindaiwa recommends that the unit be returned to your Shindaiwa dealer for service.

maIntenance InterVals

aIr fIlter

Level 1.

Tools required: 25-50 mm (1-2 in.) Cleaning brush.

NOTE

Clean daily.

Close choke (Cold Start Position [ ]). This prevents dirt from enter-

1. ing the carburetor throat when the air lter is removed. Brush accumulated dirt from air cleaner area.

Remove air lter cover. Brush dirt from inside cover.

Remove air lter and lightly brush debris from lter. Replace lter if

3. it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed.

If lter can be reused, be certain it:

• Fits tightly in the air lter cavity.

• Is installed with the original side out.

English

Install air lter cover.

fuel fIlter

Level 1.

Tools required: 200-250 mm (8-10 in.) length of wire with one end bent into a hook, Clean rag, funnel, and an approved fuel container.

WARNING

Fuel is VERY ammable. Use extreme care when mixing, storing or handling.

Use a clean rag to remove loose dirt from around fuel cap and empty

1. fuel tank.

Use the “fuel line hook” to pull the fuel line and lter from the tank.

Remove the lter from the line and install the new lter.

English

spark pluG

Level 2.

Tools required: 3/4 in. Spark Plug deep socket, Feeler gauge

IMPORTANT

Use only BPMR-8Y spark plug otherwise severe engine damage may occur.

Remove spark plug and check for fouling, worn and rounded center electrode.

Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.

Adjust spark plug gap by bending outer electrode.

Tighten spark plug to 150-170 kg/cm (130-150 in. lb.).

coolInG system

Level 2.

Tools required: 25-50 mm (1-2 in.) Cleaning brush, 3 mm Hex Wrench, Cross Head Screwdriver

Parts Required: None, if you are careful.

IMPORTANT

To maintain proper engine operating temperatures, cooling air must

pass freely through the cylinder n area. This ow of air carries

combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the cylinder.

• Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.

0.65 mm

(0.026 in.)

Removal of cooling passage blockages or cleaning of cooling ns is considered “Normal Maintenance”. Any failure attributed to lack of

maintenance is not warranted.

Cleaning Grill

Brush accumulated debris from crankcase intake grill above the fuel tank.

Cleaning Cylinder Fins

Remove spark plug lead and spark plug.

Remove two upper 3 mm hex screws at recoil starter.

Remove engine cover (ve screws), pull cover away from engine.

3. Loosely install spark plug to prevent dirt from entering cylinder. Clean

cylinder ns to allow cooling air to pass freely.

Remove spark plug and loosely reassemble engine cover with ve cross

4. head and two hex head screws.

Tighten all screws securely.

Install spark plug and spark plug lead.

eXhaust system

Spark Arrestor Screen

English

Level 2.

Tools required: Cross Head Screwdriver, 3 mm Hex Wrench, Soft metal brush

Parts Required: Spark arrestor screen, Gasket

IMPORTANT

Carbon deposits in mufer will cause a drop in engine output and

overheating. Spark arrestor screen must be checked periodically.

Remove spark lead and spark plug.

Remove two upper 3 mm hex screws at recoil starter.

Remove ve engine cover screws and remove cover from engine.

Remove spark arrestor covers (A, B), gasket (C) and spark arrestor screen

(D) from mufer. Replace screen if plugged with carbon deposits.

NOTE

When cleaning carbon deposit, be careful not to damage the catalytic

element inside mufer.

Install spark arrestor screen, gasket, and covers.

Loosely reassemble engine cover with ve cross head and two hex head

6. screws.

Tighten all screws securely.

Install spark plug and spark plug lead.

English

Cylinder Exhaust Port

Level 3.

IMPORTANT

The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. Shindaiwa strongly recommends that you return your unit to your Shindaiwa dealer for this important maintenance service.

carburetor adJustment

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the breakin period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.

High Altitude Adjustment

High altitude adjustment is not required for proper operation of this engine.

Level 2.

Tools required: Screwdriver, tachometer Parts required: None.

NOTE Every unit is run at the factory and the carburetor is set in compliance with emission regulations. This carburetor does not have acceleration and high speed adjustment needles.

Before adjusting the carburetor, clean or replace the air lter and spark

1. arrestor screen and blower pipes are installed.

Start engine and run for several minutes to reach operating temperature.

2. Stop engine. Turn red HI speed needle (A) CCW (counter clockwise) to

3. stop.

Idle Speed Adjustment with tachometer.

•Start engine and turn “idle” speed adjustment screw (B) to idle RPM found on page 21 in the "Specications" section of this manual.

Accelerate to full throttle for 2-3 seconds to clear excess fuel from

5. engine then return to idle. Accelerate to full throttle to check for smooth transition from idle to full throttle. If engine stops or stalls after full warm up return the unit to your authorized Shindaiwa dealer for repair.

Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed RPM

should be set to specications found on page 21 "Specications" of this

manual.

Check idle speed and reset if necessary.

troubleshootInG

TRAHCGNITOOHSELBUORT

melbor kP ceh sC utat eS sua yC demeR

-sknarcenignE

/drahstrats

t'nseod

trats

roterubractaleu rF oterubractaleufo dN eggolcreniartsleuF

deggolcenilleuF

roterubraC

ecalperronaelC ecalperronaelC

ruoyeeS

rednilyctaleu rF ednilyctaleufo rN oterubraC ruoyeeS

leufhtiwtewrelffu hM cirooterutxiMleu eF kohcnepO

retlifriaecalper/naelC

roterubractsujdA

Shindaiwa dealerruoyeeS

dnetakrapS

eriwgulpfo

krapso fN fohctiwspotS

melborplacirtcelE

hctiwskcolretnI

NOothctiwsnruT ruoyeeS ruoyeeS

gulptakrap kS rapso tN cerrocnipagkrapS

nobrachtiwderevoC

leufhtiwdeluoF

evitcefedgulP

).ni620.0(mm56.ottsujdA ecalperronaelC ecalperronaelC

gulpecalpeR

,snurenignE

roseidtub

tonseod

etarelecca

ylreporp

retlifri yA tridretlifri rA aewlamro eN calperronaelC

retlifleu yF tridretlifleu sF eudiser/stnanimatno nC i

leuf

ecalpeR

tnevleu dF eggulptnevleu lF eufniseudiser/stnanimatno eC calperronaelC

gulPkrap nS row/ytridgul rP aewlamro eN calperrotsujdadnanaelC

roterubra tC nemtsujdareporpm nI oitarbi tV sujdA

metsySgniloo mC etsysgnilooC

deggulp/ytrid

ninoitarepodednetxE

snoitacolytsud/ytrid

naelC

neercSrotserrAkrap nS eercsrotserrakrapS

deggulp

raewlamro eN calpeR

seodenignE

knarcton

A/ AN / mN elborpenignelanretnI ruoyeeS

,snurenignE

t'nseodrewolb

sirokrow

nevenu/kaew

epiprewol dB eggolcepi sP irbedfopu-dliu gB olcnU

esoolepi nP oitarbi nV ethgiT

degamadepi eP susiM/rae eW calpeR

Shindaiwa dealer Shindaiwa dealer

Shindaiwa dealer

English

DANGER

Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.

English

storaGe

WARNING

During operation the mufer or catalytic mufer and surrounding cover becomes hot. Always keep exhaust area clear of ammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.

Long Term Storage (Over 30 Days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:

Store unit in a dry, dust free place, out of the reach of children.

WARNING

Do not store where fuel fumes may accumulate or reach an open ame or spark.

Remove the spark plug and pour 7cc (1/4 oz.) of fresh,

Place the stop switch s in the "STOP" position.

Remove accumulation of grease, oil, dirt and debris from

3. exterior of unit.

Perform all periodic lubrication and services that are

4. required.

Tighten all screws and nuts.

7. clean Shindaiwa 2-stroke engine oil into the cylinder through the spark plug hole.

Place a clean cloth over the spark plug hole.

Pull the recoil starter handle 2-3 times to distribute

the oil inside the engine. Observe the piston location through the spark plug

hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there.

Drain the fuel tank completely and pull the recoil starter

6. handle several times to remove fuel from the carburetor.

Install the spark plug (do not connect ignition cable).

8. Remove blower pipe assembly from unit.

specIfIcatIons

MODEL ---------------------------------------------------- EB212 Hand Held

Length ------------------------------------------------------ 330 mm (13.0 in.) (w/o pipes) Width -------------------------------------------------------- 215 mm (8.5 in.) Height ------------------------------------------------------- 340 mm (13.4 in.) Weight (dry) ------------------------------------------------ 3.8 kg (8.38 lb.) Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine Displacement ----------------------------------------------- 21.2 cc (1.39 cu. in.) Bore ---------------------------------------------------------- 32.2 mm (1.27 in.) Stroke -------------------------------------------------------- 26.0 mm (1.10 in.) Carburetor--------------------------------------------------- Zama w/primer bulb Ignition System -------------------------------------------- Flywheel Magneto, capacitor discharge ignition type Spark Plug -------------------------------------------------- BPMR-8Y Gap 0.65 mm (0.026 in.) Exhaust System -------------------------------------------- Spark Arrestor Mufer w/catalyst Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio ---------------------------------------------- 50 : 1 two-stroke air cooled engine oil Gasoline ----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl

alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use

alternative fuels such as E-20 or E-85. Oil ------------------------------------------------------------ Shindaiwa One Premium Universal 2-Stroke Oil Fuel Tank Capacity --------------------------------------- 0.5 lit. (16.9 US . oz.) Recoil Starter System ------------------------------------- Automatic Recoil Starter Centrifugal Type Wide Open Throttle Speed (RPM) ---------------------- 7,000 - 8,000 Idle Speed (RPM) ------------------------------------------ 2,700 - 3,300 Maximum Air Volume ------------------------------------ 8.6 m3/min. (305 cu. ft./min.) Maximum Air Speed w/pipes (MPH) ------------------- 225.3 KM/H (140 mph) Sound Level at 50 ft. dB(A) scale per ANSI B175.2 - 65 dB(A)

English

IMPORTANT This spark ignition system complies with Canadian ICES-002

English

Shindaiwa Corporation

EPA PHASE 2 / CALIFORNIA TIER III EMISSION

CONTROL WARRANTY STATEMENT - WARRANTY RIGHTS AND OBLIGATIONS

The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and Shindaiwa Inc. are pleased to explain the emission control system warranty on your EPA Phase 2 / C.A.R.B. Tier III model year 2007 and later small off road engine (SORE). New small off road engines must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. Shindaiwa Inc. warrants the emission control system on your small off road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off road engine.

Your emission control system may include parts such as: carburetor/fuel injected system, ignition system, catalytic converter, fuel tank, fuel lines, fuel caps, valves,

canisters, lters vapor hoses, clamps connectors, and other associated components.

For certain hand-held products with engines less than or equal to 80cc displacement, the fuel tank is subject to the C.A.R.B. evaporative emission control warranty requirements of this section. Contact Shindaiwa Inc. for the models covered under the C.A.R.B. evaporative emission regulations.

Where a warrantable condition exists, Shindaiwa Inc. or its authorized service representative will repair your small off road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 2007 and later small off road engines are warranted for two years for certain emission related parts. If any emission-related part on your engine is defective, the part will be repaired or replaced by Shindaiwa Inc. or its authorized service representative.

OWNER'S WARRANTY RESPONSIBILITIES:

• As the small off road engine owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. Shindaiwa Inc. recommends that you retain all receipts covering maintenance on your small off road engine, but Shindaiwa Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

• As the small off road engine owner, you should however be aware that Shindaiwa Inc. may deny you warranty coverage if your small off road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modications.

You are responsible for presenting your small off road engine to Shindaiwa Inc.’s authorized service center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you can contact Shindaiwa Inc. at 800-521-7733 or www.shindaiwa.com

EPA PHASE 2 / CALIFORNIA TIER III EMISSIONS DEFECT WARRANTY EXPLANATION

This is additional detailed information about the EPA PHASE 2/CALIFORNIA TIER III EMISSIONS DEFECT WARRANTY for your small off road engine.

WHAT DOES THIS WARRANTY COVER?

Shindaiwa Inc. warrants that your unit was designed, built and equipped to conform with applicable EPA and California emissions standards and that your unit is free from defects in material and workmanship that would cause it to fail to conform with applicable requirements within two (2) years. The warranty period begins on the date the product is delivered to a retail purchaser. This is your emission control

system DEFECTS WARRANTY.

HOW WILL A COVERED PART BE CORRECTED?

If there is a defect in a part covered by this warranty, Shindaiwa Inc.’s authorized service dealer will correct the defect.

You will not have to pay anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.

Emissions System repairs covered under this warranty should be completed in a reasonable time, not to exceed 30 days.

IMPORTANT

If the diagnosis reveals no defect, the emission defect warranty does not apply.

WHAT PARTS ARE COVERED BY THE EPA PHASE 2/ CALIFORNIA TIER III 2007 & LATER SMALL OFF ROAD ENGINE EMISSIONS DEFECT WARRANTY?

• Any emission related part not scheduled for, "required maintenance" (See Operator’s Manual, "SERVICE MAINTENANCE SCHEDULE") will be repaired or replaced within the warranty period. The repaired or replaced part will be warranted for the remaining Emissions Defect warranty period.

• Any emission related part scheduled for replacement during "required maintenance" (See Operator’s Manual, "SERVICE MAINTENANCE SCHEDULE") is

warranted for the period of time prior to the rst scheduled replacement point for

that part. Any such part repaired or replaced under warranty shall be warranted for

the remainder of the period prior to the rst scheduled replacement point for that

part.

• Any Shindaiwa Inc. approved replacement part may be used in the performance of any warranty maintenance or repairs on emission-related parts, and must be provided without charge if the part is still under warranty.

• Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of Shindaiwa Inc.

• The owner is responsible for the performance of the required maintenance described in the operator’s manual.

SPECIFIC EMISSION RELATED WARRANTED PARTS:

Choke Carburetor (complete assembly or replaceable components) Fuel Injection Assembly or replaceable components Air Filter Electronic Ignition System Spark Plug

Catalytic Converter / Mufer Assembly

Fuel Tank (CARB only)

WHAT IS NOT COVERED BY THE EPA PHASE 2/ CALIFORNIA TIER III 2007 & LATER SMALL OFF ROAD ENGINE EMISSIONS DEFECT WARRANTY?

• Any failure caused by abuse, neglect, improper maintenance.

• Any failure caused by unapproved modications, use of unapproved add-on parts/modied parts or unapproved accessories.

+ 50 hidden pages