Sherwood AX-5103 User Manual

Caution regarding placement (Except for U.S.A. and Canada)

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.

Left and right panels : 5 cm Rear panel : 10 cm Top panel : 20 cm

Congratulations on Your Purchase!

Your new high fidelity Amplifier is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material. They will be helpful if you ever need to move your unit and may be required if you ever need to return it for service. Your unit is designed to be placed in a horizontal position and it is important to allow at least two inches of space behind your unit for adequate ventilation and cabling convenience. To avoid damage, never place the unit near radiators, in front of heating vents, in direct sunlight, or in excessively humid or dusty location. Connect your complementary components as illustrated in the following section.

UNPACKING AND INSTALLATION

Introduction

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Caution : Do not block ventilation openings or stack other equipment on the top.

WARNING

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER(OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

FOR U.S.A.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION : Any changes or modifications in construction of

this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ENGLISH

NOTE ON RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning chemical waste. This product and the accessories packed together constitute the applicable product according to the WEEE directive except batteries.

AX5103(G) 2007.8.17 4:43 PM 페이지 1

READ THIS BEFORE OPERATING YOUR UNIT

Units shipped to the U.S.A and Canada are designed for operation on 120 Volts AC only.

Observe all safety precaution for use of a polarized AC plug. However, some products may be supplied with a non polarized plug.

CAUTION : To prevent electric shock, match wide blade of plug to wide slot, insert fully.

FOR U.S.A AND CANADA .............................. 120 V

Units shipped to Australia are designed for operation on 240 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician.

PAN-EUROPEAN UNIFIED VOLTAGE All units are suitable for use on supplies 230-240 V AC.

FOR EUROPE AND AUSTRALIA ........ 230 V/240 V

FOR YOUR SAFETY

Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch.

AC VOLTAGE SELECTION

This unit operates on 110/220 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

AC voltage selector switch

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

FOR OTHER COUNTRIES .................. 110 V/ 220 V

FOR YOUR SAFETY

AC 220 V

AC 110 V

ENGLISH

AX5103(G) 2007.8.17 4:43 PM 페이지 2

CONTENTS

Introduction

• UNPACKING AND INSTALLATION | 2

• READ THIS BEFORE OPERATING YOUR UNIT | 3

System Connections | 5

Front Panel Controls | 7

DIGI LINK III System Remote Controls | 8

• REMOTE CONTROL OPERATION RANGE | 9

• LOADING BATTERIES | 9

Operations

• LISTENING TO A PROGRAM SOURCE | 10

• RECORDING | 12

Troubleshooting Guide | 13

Specifications | 14

ENGLISH

AX5103(G) 2007.8.17 4:43 PM 페이지 3

ENGLISH

AC OUTLET

230V~50Hz SWITCHED

100W(0.43A) MAX.

AC INPUT

230V~50Hz

190W

PHONO CD

TUNER

TAPE 1

/MD

IN OUT IN OUT

TAPE 2

MONITOR

DIGI LINK

SPEAKER A

SPEAKER B

AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR. WARNING : SHOCK HAZARD-DO NOT OPEN. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

GND

SN.

MODEL NO.

AX-5103

INTEGRATED AMPLIFIER

ASSEMBLED IN CHINA

DESIGNED IN USA

System Connections

• Do not connect the amplifier to the wall AC outlet when plugging and unplugging connection cords.

• Be sure to connect the white RCA pin cords to the L (left) and the red RCA pin cords to the R (right) jacks when making connections.

• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the amplifier.

PHONO CD

TUNER

TAPE 1

/MD

TAPE 2

MONITOR

GND

DIGI LINK

CONNECTING AUDIO

COMPONENTS

CONNECTING SYSTEM

CONTROL

• The TAPE1/MD IN/OUT jacks may also be connected to the LINE OUT/IN jacks of an additional MD recorder.

• The TAPE2 MONITOR IN/OUT jacks may also be connected to the LINE OUT/IN jacks of an optional graphic equalizer.

• Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system.

AX5103(G) 2007.8.17 4:43 PM 페이지 4

+ 9 hidden pages