Sharp XL-HP404E User Manual

XL-HP404E(E) TINSEA004AWZZ
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product.
1
MICRO COMPONENT SYSTEM
MODEL
XL-HP404E
OPERATION MANUAL
If you require any advice or assistance regarding your Sharp product, please visit our web-site www.sharp.co.uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland).
0301
XL-HP404E Micro Component System consisti ng of XL-HP404E (main unit) and CP-HP404E (speaker system).
Please confirm that the following accessories are included.
Remote control 1 AM loop aerial 1 FM aerial 1
Note:
Only the above accessories are included.
03/10/20 XL-HP404E(E)_FRONT.fm
TINSEA004AWZZ
XL-HP404E
Important Instruction
Special notes
NOTES FOR USERS IN THE U.K. AND IRELAND
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or AST A approved BS 1362 fuse marked
and of the same rating as above, which is also indicated on
the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use
the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being
compatible with the plug supplied, cut-off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted else­where into a 13A socket outlet as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instruc­tions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the termi­nals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug.
or
Before replacing the plug cover, make sure that:
If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
The cord grip is clamped over the sheath of the mains lead and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELEC­TRICIAN.
SERVICE INFORMATION
In the unlikely event of your equipment requiring repair, please contact the dealer or supplier from whom it was purchased. Where this is not possible, please visit our web-site www. sharp.co.uk/ customersupport. Customers without internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from lreland). Please note; all calls will be charged at local rate.
Certain replacement parts and accessories may be obtained from our main parts distributor.
WILLOW VALE ELECTRONICS LTD.
In the unlikely event of this equipment requiring repair during the guarantee period, you will need to provide proof of the date of purchase to the repairing company. Please keep your invoice or receipt, which is supplied at the
time of purchase.
0121 766 5414
0301
2
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
XL-HP404E(E) TINSEA004AWZZ
2
WARNINGS
When the ON/STAND-BY button is set at STAND-BY position,
!
mains voltage is still present inside the unit. When the ON/ STAND-BY button is set at STAND-BY pos ition, the unit may be brought into operation by the timer mode or remote control. This unit contains no user serviceable parts. Never remove cov-
!
ers unless qualified to do so. This unit contains danger ous volt­ages, always remove mains plug from the socket before any service operation and when not in use for a long period. To prevent fire or shock hazard, do not expose this appliance to
!
dripping or splashing. No objects filled with liquids, such as vases, should be placed on the apparatus.
CAUTION
This product is classified as a CLASS 1 LASER product.
!
Use of controls, adjustments or perf orm ance of procedures other
!
than those specified herein may result in hazardous radiation exposure.
As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servic­ing to qualified personnel only.
Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0.6 mW
NOTES
Recording and playback of any mat erial may require c ons ent, which
!
SHARP is unable to give. Please refer particularly to the provisions of the Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders. This equipment complies with the requirements of Directives 89/
!
336/EEC and 73/23/EEC as amended by 93/68/EEC.
Contents
Page
"
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and ind ic a t or s . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 7
"
Preparation for Use
System connect ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 10
Remote cont r ol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
"
Basic Operation
General contr ol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the cloc k . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
"
CD Playback
Listening to a CD (CDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15
Advanced CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 18
"
Radio
Listening to the r ad io . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
"
Tape Playback
Listening to a cassette tape . . . . . . . . . . . . . . . . . . . . . . . . 21, 22
" Tape Recording
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .22 - 24
"
Advanced Features
Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . .25 - 28
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 30
"
References
Troubleshooti ng c ha r t . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 - 32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Specificati ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TERMS OF GUARANTEE . . . . . . . . . . . . . . . . . . . . . .Back cover
XL-HP404E
Important Instruction
3
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
XL-HP404E
General Information
Precautions
"
General
Please ensure that the equipment is positioned i n a well venti-
!
lated area and ensure that there is at least 10 cm (4") of free space along the sides, top and back of the equipment.
10 cm (4") 10 cm (4")
Use the unit on a firm, level surface free from
!
vibration.
Keep the unit away from direct sunlight,
!
strong magnetic fields, excessive dust, humidity and electronic/electrical equip­ment (home computers, facsimiles, etc.) which generate electrical noise.
Do not place anything on top of the unit.
!
Do not expose the unit to moisture, to temperatures higher than
!
60°C (140°F) or to extremely low temperatures. If your system does not work properly, disconnect the AC power
!
lead from the wall socket. Plug the AC power lead back in, an d then turn on your system.
In case of an electrical storm, unplug the
!
unit for safety.
10 cm (4")
10 cm (4")
Hold the AC power plug by the head when
!
removing it from the wall socket, as pulling the lead can damage internal wires.
!
Do not remove the outer cover, as this may result in electric shock. Refer inter­nal service to your local SHARP service facility.
The ventilation should not be impeded by
!
covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc.
No naked flame sources, such as lighted candles, should be
!
placed on the apparatus. Attention should be drawn to the environmental aspects of bat-
!
tery disposal. The apparatus is designed for use in moderate climate.
!
This unit should only be used within the range of 5°C - 35°C
!
(41°F - 95°F).
Warning:
The voltage used must be the same as that specified on this unit. Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of acci­dent causing damage. SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified.
" Volume control
The sound level at a given volume setting d epends on speaker effi ­ciency, location, and various ot her factors. It is advisable to avoi d exposure to high volume levels. D o not turn the vol ume on to full at switch on and listen to music at moderate levels.
4
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
Controls and indic at ors
XL-HP404E
"
Front panel
1.Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10 11
1
12 13
14
2 3
4 5
6 7
15 16 17 18 19 20
8
9
2.Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 13, 25, 28
5.CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button . . . . . 13, 15, 20, 22
6.Tape Reverse Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.Tape Reverse Mode Select Button . . . . . . . . . . . . . . . . . . . 21
8.Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 14
11.Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 14
12.CD Direct Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
13.Illumination Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
14.Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
15.CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button . . . . . . . . . . 13, 15, 20, 22
16.Memory/Set Button . . . . . . . . . . . . . . . . . . . 13 , 1 8 , 2 0 , 2 5 , 2 8
17.Equaliser Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 12
18.Extra Bass/Demo Mode Button . . . . . . . . . . . . . . . . . . 10, 12
19.CD Play or Repeat, Tape Forward Play Button . . . 14, 17, 21
20.CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 15, 22
21.CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
22.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
23.Tape Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
24.Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
25.Tape Record Pause Button . . . . . . . . . . . . . . . . . . . . . . 23, 24
26.Tuning Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
27.Tuning Down Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reference page
General Information
1
25 21 22
23 24
26
27
03/10/20 XL-HP404E(E)1.fm
5
TINSEA004AWZZ
XL-HP404E
Controls and indicators (continued)
General Information
76321 4 5
14
15 16 17
1089
1211 13
1.Disc Number Indicat o rs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.CD Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.CD Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.CD Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7
6.CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.Tape Reverse Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . 21
9.Tape Forward Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . 21
10.Tape Reverse Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . 21
11.FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 19
12.Daily Timer Indic a t or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
13.FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 19
14.Tape Record Indi c a t or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
15.Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
16.Timer Play Indic ator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
17.Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Reference page
! Rear panel
! Display
4 5
6
1
2
7
1.Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.AC Power Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.FM 75 Ohms Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.AM Loop Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.Video/Auxiliary (Audio Signal) Input Sockets . . . . . . . . . . 29
7.Subwoofer Pre-output Socket . . . . . . . . . . . . . . . . . . . . . . . 30
Speaker system
!
1. Tweeter
2. Woofer
3.Bass Reflex Duct
4. Speaker Wire
3
1
2
Reference page
3
4
6
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
XL-HP404E
1
1.Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 11
2.Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 14
8 9
15 20
2
3
10
11 12
13
16 17 18 19
21
22
23
24
4 5
14
6 7
3.CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button . . . . . 13, 15, 20, 22
4.Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 12
5.Disc Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.Equaliser Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 12
7.Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
11.Tape Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
12.Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
13.CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button . . . . . . . . . . 13, 15, 20, 22
14.Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 13, 25, 28
15.CD Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
16.CD Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . 12, 18
17.CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
18.Tape Reverse Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . 21
19.Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20.Memory/Set Button . . . . . . . . . . . . . . . . . . . 13 , 1 8 , 2 0 , 2 5 , 2 8
21.CD Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
22.CD Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . 14, 17
23.Tape Forward Play Butto n . . . . . . . . . . . . . . . . . . . . . . . . . 21
24.Tape Record Pause Button . . . . . . . . . . . . . . . . . . . . . . 23, 24
Reference page
General Information
! Remote control
1
03/10/20 XL-HP404E(E)1.fm
7
TINSEA004AWZZ
XL-HP404E
System connections
Make sure to unplug the AC power lead before any connections.
Aerial connection (see page 9)
Preparation for Use
FM aerial
Right speaker
Speaker connection (see page 9)
AM loop aerial
Left speaker
Wall socket (AC 230 - 240 V, 50 Hz)
AC power connection (see page 10)
8
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
XL-HP404E
! Aerial connection
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received.
Supplied AM loop aerial:
Connect the AM loop aerial to t he AM LOOP socket. Position the AM loop aerial for optimum reception. Place the AM loop aerial on a shelf, etc., or attach it to a stand or a wall with screws (not supplied).
Note:
Placing the aerial on the unit or near the AC power lead may cause noise pickup. Place the aerial away from the unit for better recep­tion.
Installing the AM loop aerial:
< Assembling > < Attaching to the wall >
! Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) terminal.
BlackRed
Caution:
Use speakers with an impedance of 6 ohms or more, as lower im-
"
pedance speakers can damage the unit. Do not mistake the right and the left chan-
"
nels. The right speaker is the one on the right side when you face the unit.
Do not let the bare speaker wires touch
"
each other.
Do not allow any objects to fall into or to be
"
placed in the bass reflex ducts. Do not stand or sit on the speakers. You may
"
be injured.
Incorrect
! Speaker grilles are removable
Make sure nothing comes into contact with the speaker diaphragms when you remove the speaker grilles.
2
Preparation for Use
Wall Screws (not supplied)
03/10/20 XL-HP404E(E)1.fm
9
TINSEA004AWZZ
XL-HP404E
System connections (continued)
! AC power connection
After checking all the connections have been made correctly, plug the AC power lead of this unit into the wall socket. If you plug in the unit first, the unit will enter the demonstration mode.
Wall socket (AC 230 - 240 V, 50 Hz)
Notes:
The unit will start the tape initialisation when plugged in to the AC
"
socket. During this process, initialising sound will be heard and the unit cannot be turned on. Wait until the process is finished. Unplug the AC power lead from the wall socket if the unit will not
"
be in use for a prolonged period of time.
Preparation for Use
Cooling fan:
This product is equipped with a cooling fan inside, which begins to run at a specified volume level for better heat radiation.
! Demonstration mode
The first time the unit is plugged in, the unit will enter the demonstration mode. You will see words scroll.
To cancel the demonstration mode:
When the unit is in the power stand­by mode (demonstration mode), press the X-BASS/DEMO button. The demonstration mode will be cancelled and the display will disap­pear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/ DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to se­lect the extra bass mode.
! External FM aerial
Use an external FM aerial if you require better reception. Consult your dealer.
External FM aerial
10
03/10/20 XL-HP404E(E)1.fm
TINSEA004AWZZ
XL-HP404E(E) TINSEA004AWZZ
3
Remote control
! Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar). Batteries are not included.
1 Remove the battery cover. 2 Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them towards the
battery terminals.
3 Replace the cover.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
"
Do not mix old and new batteries.
"
Remove the batteries if the unit is not to be used for long per iod s
"
of time. This will prevent potential damage due to battery leak­age.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
"
operation becomes erratic. Periodically clean the transmitter on the remote control and the
"
sensor on the unit with a soft cloth. Exposing the sensor on the unit to strong light may i nterfere with
"
operation. Change the lighting or the direction of the unit. Keep the remote control away from moisture, heat, shock, and
"
vibrations.
! Test of the remote control
Check the remote control af ter checking all the connections (see pages 8 - 10). Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy music.
Remote sensor
0.2 m - 6 m (8" - 20')
XL-HP404E
2
Preparation for Use
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
"
Installing the batteries i ncorrectly may ca use t he unit t o mal func-
"
tion.
03/10/20 XL-HP404E(E)2.fm
11
TINSEA004AWZZ
XL-HP404E
Basic Operation
12
General control
! To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
! Illumination light control
When the power is turned on, light illuminates around the volume control. To turn on/off the light, hold down the CLEAR/DIMMER but­ton on the remote control more than 2 seconds.
! Volume control
Main unit operation:
When the VOLUME control is turned clockwise, the volume will increase. When it is turned anti-clockwise, the volume will decrease.
Remote control operation:
Press the VOLUME (+ or -) button to increase or decrease the volume.
.....
30 MAXIMUM0
! Bass control
When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS/DEMO (X-BASS) button.
! Equaliser
When the EQUALIZER (EQUALIZER MODE) button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER (EQUALIZER MODE) button repeat­edly until the desired sound mode appears.
FLAT ROCK CLASSIC POPS VOCAL JAZZ
The sound is not modified. Bass and treble are emphasised.
Treble is cut a little. Bass and treble are slightly emphasised.
Vocals (midrange tones) are emphasised. Treble is slightly emphasised.
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the or button to se­lect "CLOCK", and press the MEMORY/SET button.
4
Press the or button to select 24-hour or 12­hour display and then press the MEMORY/SET button.
"0:00" The 24-hour display will appear. (0:00 - 23:59) "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59)
5
Press the or button to adjust the hour and then press the MEMORY/SET button.
Press the or button once to advance the time by 1 hour. Hold it down to advance continuously.
6
Press the or button to adjust the minutes and then press the MEMORY/SET button.
Press the or button once to advance the time by 1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode] Press the CLOCK/TIMER button. The time display will appear for about 10 seconds.
[When the power is on] Press the CLOCK/TIMER button. Within 10 seconds, pr es s the or button to display the time. The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time dis­play when the AC power supply is restored after a power failure or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not appear in step 3, step 4 (for selecting the 24-hour or 12-hour dis­play) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 31 for details.]
2 Perform "Setting the clock" from step 1.
Note:
The clock can also be set with the remote control.
XL-HP404E
3
Basic Operation
13
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
XL-HP404E
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but can­not record. Some audio CD-R and CD-RW discs may not be playable due to the state of disc or the device that was used for recording.
CD Playback
! CD playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the 1 button and within 5 seconds, press the OPEN/CLOSE button to open the disc tray 1.
4
Place the CD on the disc tray 1, label side up.
Be sure to place 8 cm (3") CD in the middle of the disc trays.
12 cm (5") 8 cm (3")
5
Press the OPEN/CLOSE button to close the disc tray 1.
Total number of tracks on the CD whose number is flashing
" " will appear.
6
You can place discs on the trays 2 - 5 by following steps 3 - 5.
7
Press the / button to start playback.
CD play indicator
Total playing time of the CD whose number is flash­ing
14
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
Playback will begin from track 1 on the DISC 1. After that disc fin-
"
ishes playing, the next dis c w ill au tomatically play. After the last track on the fifth disc is played, the CD player stops
"
automatically. When there is no CD in one of the disc tray s (1 - 5), the empty
"
tray will be skipped to the next tray with a CD.
To exchange other CDs whilst playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5 seconds, press the OPEN/CLOSE button and exchange discs.
To remove the CDs:
In the stop mode, press the 1 - 5 button and within 5 seconds, press the OPEN/CLOSE button.
Caution:
Do not place two CDs in one disc tray.
"
Do not play discs with special shapes (heart- or octagon-
"
shaped). It may cause malfunctions. Do not push the disc tray whilst it is moving.
"
If the power fails whilst the tray is open, wait until the power i s
"
restored. If the disc tray is stopped with force, "ER-CD20" will appear on
"
the display for 3 seconds and the unit will not function. If this occurs, press the ON/STAND-BY button to enter the power stand-by mode and then turn the power on again. If TV or radio interference occurs during CD o peration, move the
"
unit away from the TV or radio. If a disc is damaged, dirty, or loaded upside down, the disc will
"
skip.
! Various CD functions
Function Main unit Remote
Play Press in the stop
Stop Press in the playback
Pause Press in the playback
Track up/ Track down
Fast for­ward/Fast reverse
control
Operation
mode.
mode.
mode. Press the / button to resume play­back from the paused point.
Press in the playback or stop mode.
If you press the button in the stop mode, press the / button to start the desired track.
Press and hold down in the playback mode.
Release the button to resume playback.
XL-HP404E
4
CD Playback
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit t urns on and
"
the "CD" function is activated. CD / button on the remote control: The unit turns on and CD
"
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
"
the last function starts (CD/TAPE/TUNER/VIDEO).
Notes:
Track up/track down and fast forward/fast reverse are possible
"
only within individual discs. When the end of the last track is reached during fast forward, "
"
END" will appear on the display and CD operation will be paused. When the beginning of the first track is reached during fast re­verse, the unit will enter the playback mode. ( : Last track number)
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
15
XL-HP404E
Advanced CD playback
! To specify a disc to play
You can play a disc by specifying the disc number.
1
Press one of the 1 - 5 buttons to select the desired disc.
Selected disc number
2
Within 5 seconds, press the CD DIRECT PLAY button on the main unit.
CD Playback
Playback will begin from track 1 on the chosen disc.
"
After the last track on the chosen disc is played, the CD player
"
stops automatically.
Note:
If the button of the disc tr ay wi th n o disc is pres se d, pla yba ck will n ot start and the disc indicator will go out.
! Direct track search
By using the direct search buttons, the desired tracks on the current disc can be played.
Use the direct search buttons on the remote control to select the de­sired track whilst playing the se­lected disc.
Selected track number
The direct search buttons allow you to select up to number 9.
"
When selecting number 10 or more, use the "+10" button.
"
A. For example, to choose 13
1 Press the "+10" button once. 2 Press the "3" button.
B. For example, to choose 30
1 Press the "+10" button three times. 2 Press the "0" button.
If the direct search buttons are pressed whilst the disc is stopped, press the / button to start the desired track on the current disc.
Notes:
A track number higher than the number of tracks on the disc can-
"
not be selected. During random play, direct search is not possible.
"
16
To stop playback:
Press the (CD ) button.
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
XL-HP404E
! Repeat play
Repeat play can play all 5 discs, all t racks on a chosen disc, or a programmed sequence continuously.
To repeat all tracks on up to 5 discs:
Press the / button twice.
To repeat desired tracks:
Perform steps 1 - 6 in the "Programmed play" section on page 18 and then press the / button twice.
To cancel repeat play:
Press the / button again. " " will go out.
To repeat all tracks on the chosen disc:
1 Press one of the 1 - 5 buttons. 2 Within 5 seconds, press the CD DIRECT
PLAY button twice.
To cancel repeat play:
Press the CD DIRECT PLAY button again. " " will go out.
! Random play
The tracks on the disc(s) can be played in random ord er automati cal ly.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
To cancel random play:
Press the / button. "R" will go out.
To random play all tracks on the chosen disc:
1 Press one of the 1 - 5 buttons. 2 Within 5 seconds, press the CD DI-
RECT PLAY button.
3 Press the RANDOM button on the re-
mote control.
To cancel random play:
Press the CD DIRECT PLAY button. "R" will go out.
Notes:
If you press the button during random play, you can move to
"
the track selected next by the random operation. On the other hand, the button does not allow you to move to the previous track. The beginnin g of the tr a c k bein g pla yed w ill b e loca te d. In random play, the CD player will select and play tracks auto-
"
matically. (You cannot select the order of the tracks.)
Caution:
After performing repeat or random play , be sur e to press t he (CD
) button. Otherwise, the disc(s) will play continuously.
4
CD Playback
03/10/20 XL-HP404E(E)2.fm
17
TINSEA004AWZZ
XL-HP404E
Advanced CD Playback (continued)
! Programmed play
You can choose up to 32 selections for playback in the order you like.
1
Whilst in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode.
2
Press one of the 1 - 5 buttons to select the desired disc.
Selected disc number
3
Press the direct search buttons on the remote control to select
the desired track.
CD Playback
You can also select a track by pressing the or but ton.
4
Press the MEMORY/SET (MEMO­RY) button to save the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be programmed.
If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button.
6
Press the (CD ) button.
The total number of memory will ap­pear.
7
Press the / button to start playback.
Selected track number
To clear the programmed selections:
Press the CLEAR/DIMMER button on the re­mote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track pro­grammed.
To cancel the programmed play mode:
Whilst in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared.
Adding tracks to the programme:
If a programme has been previously stored, the "MEMORY" indica­tor will be displayed. Then follow steps 1 - 6 to add tracks. The new tracks will be stored after the last track of the original programme.
To check which tracks are programmed:
Whilst the unit is stopped in the programmed play mode, press the
or button.
Notes:
When a disc with programmed tracks is ejected, the programme
"
is automatically cancelled. Even if you press the ON/STAND-BY button to enter the stand-by
"
mode or change the function from CD to another, the pro­grammed selections will no t be clea r ed . During the programme operation, random play is not possible.
"
During programme play, the CD DIRECT PLAY button will not
"
work.
18
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
Listening to the radio
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
"
turns on and the "TUNER" function is activated.
/ button on the main unit: The unit turns on and playback of
"
the last function starts (CD/TAPE/TUNER/VIDEO).
! Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button repeatedly to sel ect the desired frequency band (FM or AM).
3
Press the TUNING ( or ) button to tune in to the desired station.
Manual tuning:
Press the TUNING button as many times as required to tune in to the desired station.
Auto tuning:
When the TUNING button is pressed for more than 0.5 sec­onds, scanning will start automatically and the tuner will stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop auto-
"
matically at that point. Auto scan tuning will skip weak signal stations.
"
To stop the auto tuning, press the TUNING button again.
"
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " will appear when an FM broadcast is in stereo.
"
If the FM reception is weak, p ress the TUNER (B AND) button to
"
extinguish the "ST" indicator. The reception changes to monau­ral, and the sound becomes clearer.
FM stereo mode indicator
XL-HP404E
5
Radio
FM stereo receiving indicator
03/10/20 XL-HP404E(E)2.fm
19
TINSEA004AWZZ
XL-HP404E
Listening to the radio (continued)
! Memorising a station
You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning)
1
Perform steps 1 - 3 in "Tuning" on page 19.
2
Press the MEMORY/SET (MEMORY) button to enter the preset tuning saving mode.
3
Within 30 seconds, press the PRESET ( or ) button to select the preset channel number.
Store the stations in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY/SET (MEMORY)
Radio
button to store that station in memory.
If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a pre­set station.
When a new station is stored in memory, the station previously memorised will be erased.
Note:
The backup function protects the memorised stations for a few hours should there be a power failure or the AC pow er lead discon­nection.
! To recall a memorised station
Press the PRESET ( or ) button for less than 0.5 seconds to se­lect the desired station.
! To scan the preset stations
The stations saved in memory can be scanned automati cally. (Pre­set memory scan)
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired sta-
tion is located.
To erase entire preset memory
!
1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Whilst pressing down the button and the X-BASS/DEMO but-
ton, press the CLOCK/TIMER button until "TUNER CL" appears.
20
03/10/20 XL-HP404E(E)2.fm
TINSEA004AWZZ
Listening to a cassette tape
XL-HP404E
Before playback:
For playback, use normal or low-noise tapes for the
"
best sound. (Metal or CrO tapes are not recom­mended.)
Do not use C-120 tapes or poor-quality tapes, as
"
they may cause malfunctions. Before loading a tape into the cassette compartment,
"
tighten the slack with a pen or a pencil.
! Tape playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE button.
3
Open the cassette door by push­ing the area marked " PUSH
EJECT".
4
Load a cassette into the cas­sette compartment with side A
facing you.
5
Press the button to choose one side or both sides.
... To listen to both sides.
To play both sides ( ), start from side A. When playback starts from side B, side A will not be play e d .
... For endless repeat play of both sides. ... To listen to one side.
6
Press the / ( ) button to listen to side A, or the ( ) button for side B.
Forward play
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE button (main unit and remot e control): The unit turns on
"
and the "TAPE" function is activated. TAPE button on the remote control: The unit turns on and side
"
A playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and pl ayback of
"
the last function starts (CD/TAPE/TUNER/VIDEO).
Reverse play
6
Tape Playback
21
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
Recording on a cassette tape
! Various tape functions
Function Main unit Remote
Side A play­back
Side B play­back
Stop Press in the playback,
Fast for­ward/Fast rewind
Tape Playback
Caution:
To remove the cassette, press the (TAPE ) but ton, and then
"
open the compartment. If a power failure occurs during tape operation, the tape head will
"
remain engaged with the tape and the cassette door will not open. In this case, wait until the power is restored.
control
Operation
Press in the stop mode.
Press in the stop mode.
fast forward or fast re­wind mode.
Press in the playback or stop mode.
Before recording:
When recording important selections, make a preliminary test to
"
ensure that the desired material is properly recorded. SHARP is not liable for damage or loss of your recording arising
"
from malfunction of this unit. The volume and sound controls can be adjusted with no effect
"
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
"
CrO tapes.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the erase-
"
prevention tabs are not removed. Cassettes have removable tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
"
Cover the tab hole with adhesive tape to record on the tape with­out the tab.
Side A
Tab for side B
Tab for side A
22
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
! Recording from a CD (CDs)
You can record the desired CD using the CD DIRECT PLAY button.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Load a cassette into the cassette compartment with side A facing you.
Wind past the leader of the tape, on which recording cannot be performed.
4
Press the button to choose one side or both sides.
... To record on both sides. ... To record on only one
side.
5
Press the button.
Recording will be paused.
6
Press one of the 1 - 5 buttons to select the desired disc.
7
Within 5 seconds, press the CD DIRECT PLAY button to start recording.
Recording starts from side A.
"
Recording is started from the selected CD. When the play-
"
back of the last track is finished or the end of the tape is reached, the CD and the cassette will stop automatically.
CD playback will start approximately 7 seconds after the
"
tape starts.
To stop recording:
Press the (TAPE ) button. The CD and tape will stop.
Tape Recording
7
03/10/20 XL-HP404E(E)3.fm
23
TINSEA004AWZZ
XL-HP404E
Recording on a cassette tape (continued)
Tape Recording
24
Recording from several CDs continuously:
1 Perform steps 1 - 6 in "Recording from a CD (CDs)" on page 23. 2 Within 5 seconds, press the / ( ) button to record on side A,
or the ( ) button for side B.
To perform programmed recording:
1 Programme discs and tracks. (See page 18.) 2 Press the button. 3 Press the / ( ) button to record on side A, or the ( ) button
for side B.
To stop recording:
Press the (TAPE ) button. The CD and tape will stop.
Note:
To record on both sides, begin with side A. (If recording is started from side B, the tape will not switch over to side A.)
Auto restart function:
If the recording side is switched f rom side A to B during recording, the system will record the interrupted track on side B from its begin­ning. The recording will be made without cutting the beginning of the track on side B.
! Recording from the radio
1
Tune in to the desired station. (See page 19.)
2
Load a cassette into the cassette compartment with side A facing you.
Wind past the leader of the tape, on which recording cannot be performed.
3
Press the button to choose one side or both sides.
... To record on both sides. ... To record on only one
side.
4
Press the button.
Recording will be paused.
5
Press the / ( ) button to record on side A, or the but­ton for side B.
To record on both sides, begin with side A. (If recording is start­ed from side B, the tape will not switch over to side A.)
To interrupt recording:
Press the button. To resume recording, press the same recording button you pressed in step 5. Other buttons do not allow resuming.
To stop recording:
Press the (TAPE ) button.
Note:
If you hear a whistling noise whilst recording an AM station, move the AM loop aerial.
! Erasing recorded tapes
1 Press the TAPE button. 2 Follow steps 2 - 5 in "Recording from the radio".
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
Timer and sleep operation
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset time.
This unit has 2 types of tim er: ONCE T IMER and DAILY TIMER.
Once timer: Once timer play and once timer recording works for
For example, if you are away but want to record a programme on a radio station.
Daily timer: Daily timer play and daily timer recording works at
For example, set the timer to wake up in the every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radi o programme, and use the daily timer to wake up.
1 Set the daily timer (pages 25 - 27). 2 Set the once timer (pages 25 - 27).
Start
Note:
When set times for the daily timer and once timer overl ap, the once timer takes priority. Allow an interval of at least 1 minute between operations.
one time only at a preset time.
the same preset time everyday.
1 minute or more
Daily timer
Stop Start Stop
Once timer
! Timer playback or timer recording
Before setting timer:
1 Check that the clock is set to the correct time (refer to page 13).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the cas-
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the or button to select "ONCE" or "DAILY", and press the MEMORY/SET button.
Set the unit to the correct time if "ONCE" or "DAILY" does not appear.
sette compartment.
Continued to the next page
XL-HP404E
8
Advanced Features
25
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
Timer and sleep operation (continued)
4
Within 10 seconds, press the or button to se­lect "ONCE SET" or "DAILY SET", and press the MEMORY/
SET button.
5
Press the or button to select "PLAY" or "REC", and press the MEMORY/SET button.
The illustrations show the daily timer setting.
6
Press the or button to adjust the hour and then press the MEMORY/SET button.
The illustrations show the timer playback setting in the daily tim-
Advanced Features
er mode.
7
Press the or button to adjust the minutes and then press the MEMORY/SET button.
8
Set the time to finish as in steps 6 and 7 above.
White Red
9
Switch input with the or button, and then press the MEMORY/SET button.
To select the timer playback source: CD, TUNER or TAPE.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
!
or button, and then press the MEMORY/SET
button.
If a station has not been programmed, "NO P.SET" will be
!
displayed and timer setting will be cancelled.
10
Adjust the volume using the VOLUME control, and then press the MEMORY/SET button.
Do not turn the volume up too high.
11
Press the ON/STAND-BY button to enter the power stand­by mode.
The "TIMER" indicator lights up and the unit is ready for timer playback or timer recording.
26
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
12
When the preset time is reached, playback or recording will start.
The volume will increase gradually until it reaches the preset volume.
13
When the timer end time is reached, the system will enter the power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer will operate at the same time every day. It will contin­ue until the daily timer setting is cancelled. Cancel the daily tim­er when it is not used.
Note:
When performing timer playback or recording using another unit con­nected to the VIDEO/AUX IN sockets, select "VIDEO" in step 9.
This unit will turn on or enter the power stand-by mode automatically, however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button. 2 Within 10 seconds, press the or button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the or button to select
"ONCE CAL" or "DAILY CAL", and press the MEMORY/SET but­ton. The unit returns to the timer stand-by mode after displaying the settings in order.
Cancelling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button. 2 Within 10 seconds, press the or button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the or button to select
"ONCE OFF" or "DAILY OFF", and press the MEMORY/SET but­ton.
Timer will be cancelled (the setting will not be cancelled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To reuse the same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button. 2 Within 10 seconds, press the or button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the or button to select
"ONCE ON" or "DAILY ON", and press the MEMORY/SET button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Note:
The timer can also be set with the remote control.
8
Advanced Features
03/10/20 XL-HP404E(E)3.fm
27
TINSEA004AWZZ
XL-HP404E
Timer and sleep operation (continued)
" Sleep operation
The radio, compact disc and cassette tape can all be turned off automatically.
1
Play back the desired sound source.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the
or button to select "SLEEP", and press the MEMO­RY/SET button.
4
Press the or button to select the time. (Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
!
5 minutes - 1 minute 1-minute intervals
!
5
Press the MEMORY/SET but­ton.
"SLEEP" will appear.
6
The unit will enter the power stand-by mode automatically after the preset time has elapsed.
Advanced Features
The volume will be turned down 1 minute before the sleep op­eration finishes.
To confirm the remaining sleep time:
1 Whilst "SLEEP" is indicated, press the CLOCK/TIMER button. 2 Within 10 seconds, press the or button to select
"SLEEP X : XX". "X : XX" is sleep remaining time.
The remaining sleep time is displayed for about 10 seconds.
!
You can change the remaining sleep time whilst it is displayed by
!
pressing the MEMORY/SET button (steps 4 - 5).
To cancel the sleep operation:
Press the ON/STAND-BY button whilst "SLEEP" is indicated. To cancel the sleep operation without setting the system to the stand-by mode, proceed as follows.
1 Whilst "SLEEP" is indicated, press the CLOCK/TIMER button. 2 Within 10 seconds, press the or button to select
"SLEEP OFF", and press the MEMORY/SET button.
" To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asle ep listeni ng to the radi o and wake up to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record radio programmes whilst sleeping.
1 Set the sleep time (see left, steps 1 - 5). 2 Whilst the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 25 - 26).
Timer playback or
Sleep timer setting
1 minute - 3 hours Desired time
Sleep operation will automatically stop.
Caution:
When using the cassette deck, be sure the tape length is long enough to perform both functions. I f you want to sleep and wake up listening to a tape, and the length of the tape is shorter than the sleep timer setting, timer playback or recording will not be possible.
recording setting
End time
Timer playback or recording start time
28
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
Enhancing your system
XL-HP404E
The connection lead is not included. Purchase a commercially avail­able lead as shown below.
VCR, DVD, etc.
To the line output sockets
White
Red White
RCA lead (not supplied)
Auto power on function:
When you press any of the following buttons, the unit turns on.
VIDEO/AUX button (main unit and remote control): The unit turns
!
on and the "VIDEO" function is activated.
/ button on the main unit: The unit turns on and playback of
!
the last function starts (CD/TAPE/TUNER/VIDEO).
Red
" Listening to the playback sounds from VCR,
DVD, etc.
1
Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/AUX IN sockets.
When using video equipment, connect the audio output to this unit and the video output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
Note:
To prevent noise interference, place the unit away from the televi­sion.
" To record on a tape
1
Insert a cassette in the cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the button.
4
Press the / ( ) or button.
5
Play the VCR, DVD, etc.
" Headphones
Before plugging in or unplugging the headphones, reduce the
!
volume. Be sure your headphones have a 3.5 mm (1/8") diameter plug
!
and are between 16 ohms and 50 ohms impedance. The recom­mended impedance is 32 ohms. Plugging in the headphones disconnects t he speakers aut omati-
!
cally. Adjust the volume using the VOLUME control.
8
Advanced Features
29
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
Troubleshooting char t
" Subwoofer connection
When a commercially available speaker wit h a built-in amplifier is connected to this unit, you can enjoy sound with emphasised bass. Connect an RCA lead from a commerciall y available speaker with a built-in amplifier to the SUBWOOFER PRE-OUT socket.
Speaker with a
Advanced Features
built-in amplifier
Many potential problems can be resolved by the owner without call­ing a service technician. If something is wrong with this product, check the following bef ore calling your authorised SHARP dealer or service centre.
" General
Symptom Possible cause
The clock is not set to the
!
correct time. When a button is pressed,
!
the unit does not respond.
No sound is heard.
!
Did a power failure occur? Reset
!
the clock. (Refer to page 13.) Set the unit to the power stand-
!
by mode and then turn it back on. If the unit still malfunctions, reset
!
it. (Refer to page 31.) Is the volume level set to "0"?
!
Are the headphones connected?
!
Are the speaker wires discon-
!
nected?
" CD player
Symptom Possible cause
Playback does not start.
!
Playback stops in the mid-
!
dle or is not performed properly.
Playback sounds are
!
skipped, or stopped in the middle of a track.
Is the disc loaded upside down?
!
Does the disc satisfy the stan-
!
dards? Is the disc distorted or
!
scratched? Is the unit located near excessive
!
vibrations? Is the disc very dirty?
!
Has condensation formed inside
!
the unit?
30
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
XL-HP404E
! Cassette deck
Symptom Possible cause
Cannot record.
"
Cannot record tracks with
"
proper sound quality. Cannot erase completely.
"
Sound skipping.
"
Cannot hear treble.
"
Sound fluctuation.
"
Cannot remove the tape."If a power failure occurs during
"
Is the erase-prevention tab re-
"
moved? Is it a normal tape? (You cannot
"
record on a metal or CrO tape.)
Is there any slack?
"
Is the tape stretched?
"
Are the capstans, pinch rollers,
"
or heads dirty?
playback, the heads remain en­gaged with the tape. Do not open the compartment with great force.
! Remote control
Symptom Possible cause
The remote control does
"
not operate.
Is the AC power lead of the unit
"
plugged in? Is the battery polarity correct?
"
Are the batteries dead?
"
Is the distance or angle incor-
"
rect? Does the remote control sensor
"
receive strong light?
! Tuner
Symptom Possible cause
The radio makes unusual
"
noises continuously.
Is the unit placed near the TV or
"
computer? Is the FM aerial or AM loop aerial
"
placed properly? Move the aerial away from the AC power lead if it's located nearby.
! If trouble occurs
When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operat ed incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear al l the memory by resetting it.
! Clearing all the memory (reset)
1 Press the ON/STAND-BY button to enter the power stand-by
mode.
2 Whilst pressing down the button and the X-BASS/DEMO but-
ton, press the PRESET button until "CLEAR AL" appears.
Caution:
This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme.
9
References
03/10/20 XL-HP404E(E)3.fm
31
TINSEA004AWZZ
XL-HP404E
Maintenance
32
! Condensation
Sudden temperature changes, storage or operation i n an ext remely humid environment may cause condensation inside the cabinet (CD pickup, tape heads, etc.) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. If this happens, leave the power on with no disc (or casset te) in t he uni t until normal playback is possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the unit.
! Before transporting the unit
Remove all CDs from the unit. Make sure there is no CD in the disc tray. Then, set the unit to the power stand-by mode. Carrying the unit with discs left inside can damage the unit.
! Care of compact discs
Compact discs are fairly resi stant to damage, however mistrack ing can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collec­tion and player.
Do not write on either side of the disc, particularly the non-label
"
side from which signals are read. Do not mark this surface. Keep your discs away from direct sunlight, heat, and excessive
"
References
moisture. Always hold the CDs by the edges. Fingerprints, dirt, or water o n
"
the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius.
NO YES
Correct
! Cleaning the tape-handling parts
Dirty heads, capstans or pinch rollers can cause poor s ound and
"
tape jams. Clean these parts with a cotton swab mois tened with commercial head/pinch roller cleaner or isopropyl alcohol. When cleaning the heads, pinch rollers, etc., unplug the unit
"
which contains high voltages.
A
Pinch roller Erase head
Capstan Recording/Playback head
After long use, the deck's heads and capstans may become
"
magnetised, causing poor sound. Demagnetise these parts once every 30 hours of pla ying/recording time by u sing a commercial tape head demagnetiser. Read the demagnetiser's inst ructions carefully before use.
D
C
A
BB
! Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative maintenance (cleaning of the laser pickup lens) should be per­formed periodically. Lens cleaners are commercially available. Con­tact your local CD software dealer for options.
! Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted s oap solution, then with a dry cloth.
Caution:
Do not use chemicals for cleaning (petrol, paint thinner, etc.) . It
"
may damage the cabinet finish. Do not apply oil to the ins ide of the unit. It may cause m alfunc-
"
tions.
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
Specifications
XL-HP404E
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification fig­ures indicated are nominal values of production units. There may be some deviations from these values in individual units.
! General
Power source AC 230 - 240 V, 50 Hz Power
consumption Dimensions Width: 185 mm (7-1/4")
Weight 6.0 kg (13.2 lbs.)
100 W
Height: 260 mm (10-1/4") Depth: 307 mm (12")
! Amplifier
Output power RMS: 100 W (50 W + 50 W) (10 % T.H.D.)
RMS: 76 W (38 W + 38 W) (0.9 % T.H.D.)
Output terminals Speakers: 6 ohms
Headphones: 16 - 50 ohms (recommended: 32 ohms)
Subwoofer pre-output (audio signal): 200 mV/10 k ohms at 70 Hz
Input terminals Video/Auxiliary (audio signal): 500 mV/47 k
ohms
! CD player
Type 5-disc multi-play compact disc player Signal readout Non-contact, 3-beam semiconductor laser
D/A converter 1-bit D/A converter Frequency
response Dynamic range 90 dB (1 kHz)
pickup
20 - 20,000 Hz
! Tuner
Frequency range FM: 87.5 - 108 MHz
AM: 522 - 1,620 kHz
! Cassette deck
Frequency response
Signal/noise ratio 50 dB (recording/playback) Wow and flutter 0.3 % (WRMS)
50 - 14,000 Hz (normal tape)
! Speaker
Type 2-way type speaker system
5 cm (2") tweeter 13 cm (5-1/8") woofer
Maximum input power
Rated input power 50 W Impedance 6 ohms Dimensions Width: 165 mm (6-1/2")
Weight 2.6 kg (5.7 lbs.)/each
100 W
Height: 261 mm (10-1/4") Depth: 230 mm (9-1/16")
9
References
33
03/10/20 XL-HP404E(E)3.fm
TINSEA004AWZZ
MEMO
03/10/20 XL-HP404E(E)_MEMO.fm
TINSEA004AWZZ
MEMO
03/10/20 XL-HP404E(E)_MEMO.fm
TINSEA004AWZZ
TERMS OF GUARANTEE
Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replace­ment, of this product subject to the conditions listed below:-
1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by Sharp.
2. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession.
3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointed Service Facility within one year from the date this product was purchased. Proof of purchase must be provided.
4. The guarantee does not cover carriage costs, audio tapes, compact discs or batteries.
5. In the unlikely event of this product requiring repair, please contact the supplier from whom it was
purchased. Where this is not possible, please contact the Sharp Customer Information Centre on the telephone number given below.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to your statutory rights, and does not affect these
rights in any way.
If you have any difficulty operating this product, or would like information on other Sharp products, please telephone the Sharp Customer Information Centre on the number given below.
Sharp Customer Information Centre - Telephone 08705 274277
(or (01) 676 0648 if telephoning from Ireland)
0312
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE
SHARP CORPORATION
9906
03/10/20 XL-HP404E(E)_BACK.fm
TINSEA004AWZZ 03M R YT 2
TINSEA004AWZZ
Loading...