Sharp VT19B-PW User Manual

Solutions for Demanding Applications

VarTech Systems Inc.

Industrial CRT and Flat Panel Displays

VT19B-PW

19” Auto Sync Color Monitor

User’s Guide

Read these instructions completely before attempting to operate your new Color Display.

19” Fast Scan Series User Guide 150-062

TABLE OF CONTENTS

Sections Page

1

2

3

4

5

6

7

Panel Mount Mechanical 15

Safety Warnings

FCC Statement

Installation

Controls

Pin Assignments

Troubleshooting Guide

Mechanical Drawings

1-2

3

4

5-10

11-12

13

14

8

Specifications

16

19” Fast Scan Series User Guide 150-062

Section

1

SAFETY WARNINGS

SAFETY WARNINGS

RISK OF ELECTRIC SHOCK!

DO NOT OPEN!!!

WARRANTY VOID IF CASING IS

REMOVED.

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No

user serviceable parts inside. Refer servicing to qualified technician.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN OR
MOISTURE.

“HIGH VOLTAGE EXISTS ON THE CATHODE-RAY TUBE ANODE LEAD OF THIS MONITOR.
BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE BY CONNECTING
THE H.V. METER BETWEEN THE ANODE OF CRT CAP AND CHASSIS ONLY.”

CAUTION

1. Keep monitor away from excessive dust, high temperature, moisture or direct sunlight.

2. Use in well ventilated area and do not cover ventilation openings.

3. Unauthorized modifications of this equipment or substitution or attachment of not shielded
connecting cable may cause excessive interference.

4. When the monitor is not in use for a long time, turn off power switch.

-1-

19” Fast Scan Series User Guide 150-062

IMPORTANT SAFETY INSTRUCTIONS

Prior to using this product, please ensure that you have carefully followed all the procedures outlined
in the user’s manual for this product.

1. Read all of these instructions.

2. Save these instructions for later use.

3. Follow all warnings and instructions marked on the product.

4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water.

6. Do not place this product on an unstable cart, stand or table. The product may fall causing
serious damage to the product.

7. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure
reliable operation of the product and to protect it from overheating, those openings must not be
blocked or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should never be placed near or over a radiator or
heat register. This product should not be placed in a built-in installation unless proper ventilation
is provided.

8. This product should be operated from the type of power source indicated on the marketing label.
If you are not sure of the type of power available, consult your dealer or local power company.

9. This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable
to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the purpose of grounding type plug.

10. Do not allow anything to rest on the power cord. Do not locate this product where persons will
walk on the cord.

11. If an extension cord is used with this product, make sure that the total of the ampere ratings on
the products plugged into the extension cord do not exceed theextension cord ampere rating.
Also, make sure that the total of all products plugged into the wall outlet does not exceed 15
amperes.

12. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
Never spill liquid of any kind on the product.

13. Do not attempt to service this product yourself, as opening or removing covers may expose you
to dangerous voltage points or other risks. Refer all servicing to service personnel.

14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under
the following conditions:

A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are followed.

Adjust only those controls that are covered by the operating instructions since improper
adjustment of other controls may result in damage and will often require extensive work by

a qualified technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for service.

-2-

19” Fast Scan Series User Guide 150-062

Section

FCC STATEMENT

FCC STATEMENT

2

FCC CLASS A STATEMENT

The equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a business installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in strict accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measure:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnected cables and shield power cords must be employed with this equipment to
insure compliance with the pertinent RF emission limits governing this device.

Changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment.

-3-

19” Fast Scan Series User Guide 150-062

Section

3

INSTALLATION

1.Be sure your cable(s) are attached to the respective graphics board.

2.Set the BNC/D-SUB Source for video input

3.Connect the AC power cable to a properly grounded outlet.

4.Boot your computer. Turn on the monitor power. The power LED indicator should be

illuminated. If your monitor screen remains blank, check your video controller and computer
system.

INSTALLATION

INSTALLATION

-4-

19” Fast Scan Series User Guide 150-062