Sharp UP-600D User Manual

®

POS TERMINAL

MODEL

UP-600D

READ THIS FIRST

Thank you very much for your purchase of the SHARP POS Terminal Model UP-600D.
Before you start installation, please read this leaflet carefully, which includes precautions you must
understand for safety purposes. We provide the UP-600D Instruction Manual and Inline Manual in a PDF file
format. Please contact your Authorized Sharp Dealer for your copy of the Instruction and Inline Manuals.
Keep this leaflet for future reference.

CAUTION

The AC power socket-outlet should be installed near the equipment
and should be easily accessible.

IMPORTANT

• Install your POS terminal in a location that is not subject to direct sunlight, unusual temperature

changes, high humidity or exposure to water sources. Please keep the POS terminal away from
heat and magnetic sources.

Installation in such locations could cause damage to the cabinet and the electrical components.

• The POS terminal should not be operated by an individual with wet hands.
The water could seep into the interior of the POS terminal and cause component failure.

• Do not apply excessive pressure to the display.
Do not use a sharp-pointed object on the display, or the LCD may become damaged.

• When cleaning your POS terminal, use a dry, soft cloth. Never use solvents, such as benzine and/

or thinner.

The use of such chemicals will lead to discoloration or deterioration of the cabinet.

• The POS terminal plugs into any standard wall outlet (Official (nominal) voltage) with a dedicated

earth-ground.

Other electrical devices on the same electrical circuit could cause the POS terminal to malfunction.

• If the POS terminal malfunctions, call your authorized SHARP dealer for service - do not try to

repair the POS terminal yourself.

• For a complete electrical disconnection, remove the AC power cord from the wall outlet.

PRECAUTION

This POS terminal has a built-in memory protection circuit which is operated by a rechargeable battery pack.
It should be mentioned that all batteries will, in time, dissipate their charge even if not used. Therefore to
insure an adequate initial charge in the protection circuit and to prevent any possible loss of memory upon
installation, it is recommended that each unit be allowed to be charged for a period of 24 to 48 hours prior to
use by the customer.
In order to charge the battery pack, the machine must be plugged in. This charging precaution can prevent
unnecessary initial service calls.

MODEL APPEARANCE

UP-600D

Journal cover

Receipt paper

Ribbon cover

Drawer

Drawer lock

– 1 –

Customer display (Pop-up type)

Operator display

Contrast control

Power switch

Mode switch

Keyboard

HOW TO RECEIVE YOUR COPY OF THE UP-600D
INSTRUCTION AND INLINE MANUALS

We provide the UP-600D Instruction Manual and Inline Manual in a PDF file format. To obtain them, please
contact your authorized SHARP dealer.

SPECIFICATIONS

Model: UP-600D

External dimensions: 445(W) x 485(D) x 312(H) mm

Weight: 16.8 kg

Power source*: Official (nominal) voltage and frequency

Power consumption: Stand-by: 20 W

Working temperatures: 0 to 40 °C

Electronics: LSI (CPU) etc.

Built-in battery: Rechargeable battery pack, memory holding time of about 1 month (with fully charged

Display: Operator display: LCD display

Printer: Type: 2-station serial dot-matrix (7 x 7 font) printer

Ink ribbon cassette: Color: Purple (single color)

Paper roll: Width: 44.5 ± 0.5 mm

Cash drawer: 4 slots for bill and 8 for coin denominations

Accessories: Manager key 2

* When operating your POS terminal, please check the rating label in advance.

• Specifications and appearance are subject to change for improvement without notice.

Operating: 56 W (when the official voltage is 220V – 230V)

built-in battery pack, at room temperature)

Customer display: 7-segment display (7 positions)

Printing speed: Approx. 3.0 lines/second
Printing capacity: 24 digits each for receipt and journal paper

Width: 13 mm
Length: 9 meters

Max. diam.: 83 mm
Weight: 52.3 – 64.0 g/m2 (bond paper)

Submanger key 2
Operator key 2
Printer cover lock key 2
Ink ribbon cassette 1
Paper roll 2
Take-up spool 1
Leaflet 1 copy
Drawer lock key 2
Bill separator 1
Ferrite cores 3 (

57 W (when the official voltage is 230V – 240V)

83.18 (W) x 55.18 (H) (0.24 x 0.21 mm/pixel)
Dark blue and white

used for communications cabling installation

)

SHARP CORPORATION

– 2 –

Printed in Korea

T(TINSE2487BHZZ)

➀