Sharp SMD3070ASY Installation manual
Microwave Drawer : SMD2470AS, SMD2470AH, SMD3070AS
INSTALLATION MANUAL
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30").
UNPACKING YOUR MICROWAVE DRAWER
• Remove all packing
materials from inside
the Microwave Drawer.
DO NOT REMOVE
THE WAVEGUIDE
COVER, which is
located on the top
of the Microwave
Drawer.
• Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent
drawer, damaged drawer seals and sealing surfaces, broken
or loose Microwave Drawer guides and dents inside the cavity
or on the front side of the drawer. If there is any damage, do
not operate the Microwave Drawer and contact your dealer or
a SHARP AUTHORIZED SERVICER.
Sealing
surface
Waveguide
cover
Oven
cavity
IMPORTANT NOTES TO THE INSTALLER
Sealing
surface
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future
reference.
• As when using any microwave oven generating heat, there
are certain safety precautions you should follow. These are
listed in the Operation Manual. Read all and follow carefully.
• Be sure your Microwave Drawer is installed and grounded
properly by a qualied installer or service technician.
IMPORTANT SAFETY INSTRUCTIONS
If the information in this manual is not followed
exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
• This Microwave Drawer must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
• Read all of the Installation Manual before installing the
Microwave Drawer.
• Remove all packing material before connecting the electrical
supp l y.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
Stepping, leaning or sitting on the drawer may
result in serious injuries and can also cause damage to the
Microwave Drawer.
• Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
STOP/CLEAR to prevent unintended use.
1
1
CLEARANCES AND DIMENSIONS
B
C
G
D
A
F
E
• Dimensions that are shown in Figure 1 (for 24") or Figures
4 and 5 (for 30") must be used. Given dimensions provide
minimum clearance. Locate electrical outlet in the shaded
area in the upper left-hand corner of the cutout. See Figure 9.
• Contact surface must be solid and level. Pay special attention
to the oor on which the Microwave Drawer will sit. The
o or of the opening should be cons t r uct ed of ply wood strong
enough to support the weight of the oven (about 100 pounds).
• Check location where the Microwave Drawer will be
installed for proper electrical supply.
24" MICROWAVE DRAWER MEASUREMENTS
B
M
G
I
L
D
F
J
I
A
E
K
Q
H
P
N
• Your oven can be built into a cabinet or wall by itself or
under a gas or electric wall oven.
• Be sur
e that the clearance of the oor between the wall oven
and the microwave drawer is a minimum of 2-inches.
• The microwave interior will easily accommodate a 9" x 13"
oblong dish or a bag of microwave popcorn.
• The oven can also be mounted ush. Please see instructions
for ush mounting included with the Flush Mount Deector
vent.
B
C
F
C
J
A
G
I
D
H
Figure 1
A. 6"
B. Suggested electrical outlet location*
C. Anti-Tip block
D. 5"
E. 3-1/2"
F. 4"
G. 22-1/8" opening
H. 14-13/16" to bottom of Anti-Tip block
I. Allow 7/8" overlap
J. 23-1/2" minimum depth
K. Allow 3/16" overlap
L. 36" countertop height
M. Allow 7/16" minimum space
N. Floor must support 100 lb
O. 24" cabinet minimum
P. 15-9/16" opening
Q. Allow 1/8" overlap
O
Figure 2
A. 21-5/8"
B. 4-11/16"
C. 1-3/4"
D. 21-7/8"
E. 23-7/8"
E
F. 15 -7/ 8 "
G. 14-19/32"
H. 1-9/64" door thickness
I. 15" auto drawer opening
J. 4"
Figures 1 and 2 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.
This Microwave Drawer can be installed below any electric or
gas wall oven.
* Can also be installed using an electrical outlet in an adjacent cabinet
within the area where the provided electrical cord can reach. Power
cord access hole in cabinet should be a minimum 1 1/2" diameter
hole and deburred of all sharp edges.
IMPORTANT
electrical outlet to prevent tension.
Always check electrical codes for requirements.
Always allow sufcient power cord length to the
2
This drawing represents a typical standard cabinet. If installed in custom
Move oven location downward for
cabinets with extended counter tops, take into account visibility and access
to controls. See Figure 3.
A
B
E
C
D
G
A. 25"
extended countertops
Extended countertops
Figure 3
B. 1/2" minimum
C. 15 -7/8"
D. 36"
E. Control panel shown in open position
F. 24"
G. 34 -1/2"
F
3
Loading...