SHARP SMD2499FSC Installation guide

Download

Page 1

Convection Microwave Drawer: SMD2499FS

INSTALLATION MANUAL

SPECIAL WARNING

• INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

• IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.

• READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES AND DIMENSIONS

For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 2 - 4. See Figures 1 - 7.

UNPACKING YOUR CONVECTION MICROWAVE DRAWER

A minimum of two people are required to handle the oven. Use the two handles located on each side of the oven to lift.

1 Remove all packing materials from inside the Convection Micro-

wave Drawer and on the Drawer door.

2 Remove the feature sticker, if there is one. Check the drawer for

any damage, such as misaligned or bent drawer, damaged drawer seals and sealing surfaces, broken or loose drawer guides and dents inside the cavity or on the front side of the drawer. If there is any damage, do not operate the Convection Microwave Drawer and

contact your dealer or a SHARP AUTHORIZED SERVICER.

IMPORTANT NOTES TO THE INSTALLER

• Read all of the Installation Manual before installing the

Convection Microwave Drawer.

• Remove all packing material before connecting the electrical

supply.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

IMPORTANT NOTES TO THE CONSUMER

Keep this manual with your Operation Manual for future reference.

• As when using any oven generating heat, there are certain safety

precautions you should follow. These are listed in the Operation Manual. Read all and follow carefully.

• Be sure your Convection Microwave Drawer is installed and

grounded properly by a qualied installer or service technician.

• This unit comes equipped with a Wi-Fi connectivity option. In order to activate the Wi-Fi functionality, the area in which the unit is installed requires a Wi-Fi signal. Please see the

operation manual for the minimum Wi-Fi specications.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed

exactly, a re or electrical shock may result that could cause property

damage, personal injury or death.

• This Convection Microwave Drawer must be electrically

grounded in accordance with local codes.

• Make sure the wall coverings and the cabinets around the

Convection Microwave Drawer can withstand the heat generated by the Convection Microwave Drawer.

Sealing Surface

Oven Cavity

NEVER LEAVE CHILDREN ALONE OR UNATTENDED IN THE AREA WHERE A CONVECTION MICROWAVE DRAWER IS IN USE. NEVER LEAVE THE DRAWER OPEN WHEN THE OVEN IS UNATTENDED.

STEPPING, LEANING OR SITTING ON THE DRAWER MAY RESULT IN SERIOUS INJURIES AND CAN ALSO CAUSE DAMAGE TO THE CONVECTION MICROWAVE DRAWER.

• Do not use the Convection Microwave Drawer as a storage

space. This creates a potentially hazardous situation.

• Check that the time-of-day is in the display. If not, touch STOP/

CLEAR for safety reasons and to prevent unintended use.

1 E

Page 2

CLEARANCES AND DIMENSIONS

• Dimensions that are shown in Figure 1 must be used. Given

dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See Fi g u r e 9.

• Contact surface must be solid and level. Pay special attention to

the oor on which the Convection Microwave Drawer will sit. The oor of the opening should be constructed of plywood strong

enough to support the weight of the oven (about 125 pounds).

• Check location where the Convection Microwave Drawer will be

installed for proper electrical supply.

• Your oven can be built into a cabinet or wall as a stand-alone unit.

It can also be installed under: Wall Ovens: Gas or Electric SuperSteam oven: SSC2489DS Cooktop Models: SDH3042DB, SDH3652DB, SCR3042FB,

SCR2442FB, SCR3041GB, SCH3043FB, SCH2443FB,

SDH3042DB or SDH3652DB.

• Be sure that the clearance of the oor between the wall oven and

the Convection Microwave Drawer is a minimum of 2-inches.

• The Convection Microwave Drawer interior will easily accom-

modate a 9" x 13" oblong dish or a bag of microwave popcorn.

• The oven can also be mounted ush. Please see instructions for

ush mounting.

24" CONVECTION MICROWAVE DRAWER STANDARD MOUNT AND MEASUREMENTS

A. Suggested electrical outlet

location* B. 5" (127 mm) C. 4" (101.60 mm)

/8" (568.32 mm) opening

D. 22

/8" (492.12 mm)

E. 19

F. Allow

/8" (15.87 mm)

overlap

/2" (596.90 mm)

G. 23

minimum depth

Figure 1

H. Allow

/8" (3.17 mm) overlap

I. 36" (914.40 mm) countertop

height

J. Allow

/2" (12.7 mm)

minimum space

K. Floor must support

125 lbs (56.7 kg)

L. 24" (609.60 mm) cabinet

minimum

/2" (495.3 mm) opening

M. 19

Figure 2

A. 21 7/8" (555.56 mm)

/16" (119.06 mm)

B. 4

/4" (44.45 mm)

C. 1

/8" (555.63 m m)

D. 20

/8" (600.07 mm)

E. 23

/8" (498.48 mm)

F. 19

G. 19

/4" (488.95 mm)

/8" (41.27 mm) door thickness

H. 1

/2" (393.7 mm) auto drawer

I. 15

opening

J. 4" (101.60 mm)

Figures 1 and 2 contain many Convection Microwave Drawer measurements for reference when planning the drawer’s location.

* Can also be installed using an electrical outlet in an adjacent cabinet

within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 and deburred of all sharp edges.

IMPORTANT

electrical outlet to prevent tension.

Always check electrical codes for requirements.

Always allow sufcient power cord length to the

/2" diameter hole

Page 3

Move oven location downward for

24" CONVECTION MICROWAVE DRAWER STANDARD MOUNT AND MEASUREMENTS

Figure 3 represents a typical standard cabinet. If installed in custom cabinets with extended countertops, take into account visibility and access to controls. See Figure 4.

extended countertops

Extended countertops

Figure 4

Figure 3

A. 25" (635 mm)

/2" (12.7 mm) minimum

/8" (498.48 mm)

C. 19 D. 36" (914.40 mm) E. Control panel shown in open position F. 24" (609.60 mm)

/2" (876.30 mm)

G. 34

3 E

Page 4

24" CONVECTION MICROWAVE DRAWER FLUSH MOUNT AND MEASUREMENTS

must sit 1

/8" (41.27 mm) back from the face of the cabinet.

Front view

Prepare cabinet opening as shown in Figures 5, 6, 7

A. Suggested electrical outlet location

Figure 5

B. 5" (127 mm) C. 4" (101.60 mm)

/8" (606.43 mm)

D. 23

/8" (492.12 mm)

E. 19

/8" (41.27 mm)

F. 1

/2" (596.90 mm) minimum depth

G. 23

/8" (568.32 mm)

H. 22

/8" (41.27 mm) to front of shelf

I. 1

/8" (504.83 mm) opening

J. 19 K. Floor must support 125 lbs (56.7 kg)

Suggested electrical

outlet location

Top view

Mounting cleat

Drawer face

Note: the mounting surface of the finished cleat

Figure 6

No oven shown

A. 22

/8" (568.32 mm) mounting cleat opening width

B. 0" ush

/8" (41.27 mm) front of cleat to cabinet face

Cabinet

face

C. 1

A. 22 3/8" (568.32 mm) mounting cleat opening width

/8" (606.43 mm) ush opening width

B. 23

/8" (3.17 mm) from opening to top of shelf

Figure 7

Page 5

ELECTRICAL OUTLET

DRAWER INSTALLATION

The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided.

The drawer is equipped with a 3-prong grounding plug. It must be plugged into a wall receptacle that is properly installed and

grou n ded. Should you on ly have a 2- p rong outlet , have a qua lied

electrician install a correct wall receptacle.

Note: If you have any questions about the grounding or electrical

instructions, consult a qualied electrician or serviceperson.

* Can also be installed using an electrical outlet in an adjacent cabinet

within the area where the provided electrical cord can reach.

Always check electrical codes for requirements.

Figure 8

1. Place the Convection Microwave Drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet.

2. Carefully guide the Convection Microwave Drawer into the prepared opening. Avoid pinching the cord between the oven and the wall.

3. Slide the Convection Microwave Drawer all the way until

the mounting ange is ush with the face of the cabinet. See

Fi g u re 9.

4. Open the drawer. Using the 4 holes on the drawer as a template, pre-drill the cabinet using a

5. Secure the drawer with the 4 screws supplied. See Figure 10.

/16" bit. See Figure 9.

GROUNDING INSTRUCTIONS

This appliance must be grounded. The Convection Microwave Drawer is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.

– Improper use of the grounding plug can result

in a risk of electric shock. Do not use an extension cord. If the

power supply cord is too short, have a qualied electrician or

serviceperson install an outlet near the appliance.

Side Rail

Figure 9

Parts supplied - 4 Screws

Figure 10

5 E

Page 6

MODEL AND SERIAL NUMBER LOCATION

BEFORE YOU CALL FOR SERVICE

The nameplate includes model and serial number. Open the Convection Microwave Drawer fully. The label is located at the bottom left side of the oven face plate.

CARE, CLEANING AND MAINTENANCE

Refer to the Operation Manual for cleaning instructions.

Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this oven.

Refer to the warranty in your Operation Manual for Sharp’s tollfree service number and address. Please call or write if you have inquiries about your oven and/or need to order parts.

Page 7

Page 8

SHARP ELECTRONICS CORPORATION • 100 Paragon Drive • Montvale, New Jersey 07645 • USA

TINSEB580MRR2 SEp 22, 2021