Sharp SMD2470ASY Installation Manual

24" Flush Mount DeFlector Vent: sKMD24F0As

INSTALLATION INSTRUCTIONS

Important notes to the Installer

• Read all of the Installation Manual that is included with

the Microwave Drawer before installing in the ush mount
conguration.

• Observe all governing codes, ordinances, and safety

instructions.

 •Be sure to leave these instructions with the consumer.

1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.

A

C

E

H

Note: the face of the shelf must

3

sit 1

M

N

/4" (44.45 mm) back from

the face of the cabinet.

shelf face

I

Figure 1

B

D

F

G

K

L

J

O

cabinet face

Parts includes:

Qty. Part number

PR EF-B019MRP0
Flush Mount

1

Deector Vent

LX-CZB055MRE0

2

Mounting screws

A. 6" (152.40 mm)

B. Suggested electrical outlet location
C. Anti-Tip block

D. 5" (127 mm)
E. 3-1/2" (88.90 mm)
F. 4" (101.60 mm)
G. 24-3/16" (614.35 mm) minimum

24-1/2" (622.3 mm) maximum

H. 14-13/16" (376.24 mm) to bottom of

Anti-Tip block

I. 1-1/16" (26.97 mm)
J. 23-1/2" (596.90 mm) minimum depth
K. 22-1/8" (561.97 mm)
L. 1-3/4" (44.45 mm)
M. 16-7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1-3/4" (44.45 mm)

Figure 2A

A

C

L

Top view

Anti-Tip block

Mounting cleat

Drawer face

Note: the mounting surface of the finished cleat must sit 1
from the face of the cabinet [pushing the face of the drawer out

B

C

Cabinet

face

E 1

1

/16" (26.97 mm) back

1

/4" (6.35 mm)].

A. 22" (558.8 mm) mounting cleat opening width
B. 1/4" (6.35 mm)
C. 1-1/16" (26.97 mm)

TINSEB541MRR2

Shelf detail showing the deflector vent installed.

Shelf detail showing the deflector vent during installation.

Suggested electrical

outlet location

No oven

A

B

3. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.

4. Carefully guide the drawer into the prepared opening. Avoid

Anti-Tip block

contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.

5. Slide the drawer all the way back until the mounting anges

C

touch the cleats mounted in the cabinet opening.

6. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.

Figure 2B

Front view

A. 22-1/8" (561.97 mm) mounting cleat opening width
B. 24-3/16" (614.35 mm) minimum

24-1/2" (622.3 mm) maximum
ush opening width

C. 3/4" (19.05 mm) shelf

Move oven location
downward for extended
countertops for better
viewing angle.

7

16

/8"

(428.62 mm)

Front face of cabinet

Figure 2C

flush opening

height

front face of shelf

3

1

/4" (44.45 mm)

Side view

3

/4" (19.05 mm)

shelf

Anti-Tip

block

Mounting
flange

Figure 4

7. Secure the drawer with the 4 screws supplied.

2. Install deector as shown in Figure 3A.

Position deflector vent and mark holes. Pre drill using a

Figure 3A

Figure 3B

1

/16" (1.57 mm) bit before mounting.

E 2