Page 1
A
I
24" FLUSH MOUNT DEFLECTOR VENT:
back
from the face of the cabinet [pushing the face of the drawer out
/4" (6.35 mm)].
SKMD24F0AS / SKMD24F0AH
INSTALLATION INSTRUCTIONS
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual that is included with the Microwave Drawer before installing in the ush mount conguration.
• Observe all governing codes, ordinances, and safety instructions.
• Be sure to leave these instructions with the consumer.
Parts includes:
Part SKMD24F0AS SKMD24F0AH
PR EF-B019MRP0
Flush Mount Deector Vent (Stainless steel)
Qt y. 1
LX-CZB055MRE0
Mounting screws (Stainless steel)
Qt y. 2
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
Figure 1
B
D
F
G
K
L
J
Anti-Tip block
M
C
E
H
Note: the face of the shelf must
3
sit 1
/4" (44.45 mm) back from
the face of the cabinet.
N
shelf face
O
cabinet face
PREF-B026MRP0
Flush Mount Deector Vent (Dark gray)
Qt y. 1
LX-CZB073MRE0
Mounting screws (Black)
Qt y. 2
A. 6" (152.40 mm)
B. Suggested electrical outlet location
C. Anti-Tip block
D. 5" (127 mm)
E. 3-1/2" (88.90 mm)
F. 4" (101.60 mm)
G. 24-3/16" (614.35 mm) minimum
24-1/2" (622.3 mm) maximum
H. 14-13/16" (376.24 mm) to bottom of
Anti-Tip block
I. 1-1/16" (26.97 mm)
J. 23-1/2" (596.90 mm) minimum depth
K. 22-1/8" (561.97 mm)
L. 1-3/4" (44.45 mm)
M. 16-7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1-3/4" (44.45 mm)
Mounting cleat
A. 22" (558.8 mm) mounting cleat opening width
B. 1/4" (6.35 mm)
Cabinet
C
face
1
/16" (26.97 mm)
1
A
C
L
Top view
Drawer face
Note: the mounting surface of the finished cleat must sit 1
B
C. 1-1/16" (26.97 mm)
Figure 2A
E 1
TINSEB541MRR4
Page 2
Shelf detail showing the deflector vent installed.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a
bit before mounting.
Front view
No oven
Suggested electrical
Anti-Tip block
Side view
Move oven location
downward for extended
countertops for better
viewing angle.
Anti-Tip
Mounting
A
outlet location
B
C
Figure 2B
A. 22-1/8" (561.97 mm) mounting cleat opening width
B. 24-3/16" (614.35 mm) minimum
24-1/2" (622.3 mm) maximum
ush opening width
C. 3/4" (19.05 mm) shelf
7
16
/8"
(428.62 mm)
flush opening
height
3
/4" (19.05 mm)
shelf
3. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.
4. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.
5. Slide the drawer all the way back until the mounting anges
touch the cleats mounted in the cabinet opening.
6. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.
flange
Figure 4
block
7. Secure the drawer with the 4 screws supplied.
Front face of cabinet
Figure 2C
2. Install deector as shown in Figure 3A.
Figure 3A
3
1
/4" (44.45 mm)
front face of shelf
1
/16" (1.57 mm)
Figure 3B
E 2
Page 3
A
I
30" FLUSH MOUNT DEFLECTOR VENT: SKMD30F0AS
back
from the face of the cabinet [pushing the face of the drawer out
/4" (6.35 mm)].
INSTALLATION INSTRUCTION
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual that is included with
the Microwave Drawer before installing in the ush mount
conguration.
• Observe all governing codes, ordinances, and safety
instructions.
• Be sure to leave these instructions with the consumer.
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
B
C
E
H
Note: the face of the shelf must
3
sit 1
/4" (44.45 mm) back from
the face of the cabinet.
N
shelf face
Figure 1
G
L
D
F
K
J
M
Parts includes:
Qty. Part number
PREF-B020MRP0
Flush Mount
1
Deector Vent
LX-CZB055MRE0
2
Mounting screws
A. 6" (152.40 mm)
B. Suggested electrical outlet location
C. Anti-Tip block
D. 5" (127 mm)
E. 3-1/2" (88.90 mm)
F. 4" (101.60 mm)
G. 30-5/16" (769.92 mm) minimum
30-5/8" (777.87 mm) maximum
H. 14-13/16" (376.24 mm) to bottom of
Anti-Tip block
O
cabinet face
I. 1-1/16" (26.97 mm)
J. 23-1/2" (596.90 mm) minimum depth
K. 28-7/16" (722.3 mm)
L. 1-3/4" (44.45 mm)
M. 16-7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1-3/4" (44.45 mm)
Anti-Tip block
Mounting cleat
A. 28-1/2" (723.9 mm) mounting cleat opening width
B. 1/4" (6.35 mm)
Cabinet
face
1
/16" (26.97 mm)
A
C
L
Top view
Drawer face
Note: the mounting surface of the finished cleat must sit 1
B C
C. 1-1/16" (26.97 mm)
1
Figure 2A
E 3
Page 4
Shelf detail showing the deflector shield installed.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a
bit before mounting.
Front view
Suggested electrical
outlet location
Anti-Tip block
Mounting
Side view
Move oven location
downward for extended
countertops for better
viewing angle.
Anti-Tip
Figure 2B
No oven
A
B
C
A. 28-7/16" (722.3 mm) mounting cleat opening width
B. 30-5/16" (769.92 mm) minimum
30-5/8" (777.87 mm) maximum
ush opening width
C. 3/4" (19.05 mm) shelf
7
16
/8"
(428.62 mm)
flush opening
height
3
/4" (19.05 mm)
shelf
block
3. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.
4. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.
5. Slide the drawer all the way back until the mounting anges
touch the cleats mounted in the cabinet opening.
6. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.
flange
Figure 4
7. Secure the drawer with the 4 screws supplied.
Figure 2C
2. Install deector as shown in Figure 3A.
Figure 3A
Front face of cabinet
3
1
/4" (44.45 mm)
front face of shelf
1
/16" (1.57 mm)
Figure 3B
100 Paragon Drive, Suite #100, Montvale, NJ 07645, USA • 1-800-BE-SHARP (237-4277)
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9, Canada
E 4
Loading...