INSTALLATION INSTRUCTIONS
For Sharp Carousel® Built-in Kit Models
RK-48S27, RK-48S30, RK-52S27 or RK-52S30.
THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS
TO BE INSTALLED ABOVE ANy ELECTRIC WALL OVEN. PLEASE SEE THE
OPERATION MANUAL REGARDING APPROVED BUILT-IN APPLICATIONS.
* S= Stainless
IMPORTANT:
This Built-in Kit is designed for and approved only for those
Sharp Microwave Ovens specifying Built-In Kit RK-48S27,
RK-48S30, RK-52S27 or RK-52S30. Refer to operation
manual for approved models.
ITEM PART NAME QTY
PLEASE READ THESE INSTRUCTIONS
BEFORE BEGINNING INSTALLATION!
• Be sure to DISCONNECT THE PLUG of the microwave
oven from the electrical outlet before installing the Built-in
Kit. Remove the Carousel turntable from the oven cavity.
• Because the kit includes metal parts, due caution should
be used in handling and installation to avoid the possibility of injury.
THOROUGHLY
A B
A FRAME ASSEMBLY 1
B EXHAUST DUCT
ASSEMBLY
C SCREW C
(4mm x 12mm long)
D SCREW D
(3mm x 47mm long)
C
L
V-cut
indicates
center of
duct
1
2
4
C D
XOTS740P12000 LX-CZB012MRE0
1
STEP 1 CABINET OR WALL OPENING
The opening in the wall or cabinet must be within the
following dimensions:
Cut Out Minimum
Model Height (A) Width (B) Depth (C)
RK-48S27
RK-48S30
RK-52S27
RK-52S3 0
Outlet should NOT be in the shaded area as indicated on
Sketch 1.
NOTES
• If the dimension of DEPTH (C) is more than 21", the outlet
location may be any area on the rear wall.
• The oor of the opening should be constructed of plywood
strong enough to support the weight of the oven and
oor load (about 100 pounds). The oor should be level
for proper operation of the oven. Be sure to check the
local building code as it may require that the opening be
enclosed with sides, ceiling and rear partition. The proper
functioning of the oven does not require the enclosure.
16" 25
1
16
/4" 26 1/8" to 26 3/8" 20"
1
/8" to 25 3/8" 20"
4"
A
4"
B
C
Sketch 1
2
STEP 2 EXHAUST DUCT ASSEMBLY INSTALLATION
FOR MODELS: RK-48S27 OR RK-48S30
1. Place the EXHAUST DUCT ASSEMBLY in the center of
the opening. Align the front edge of the duct with the front
of the cabinet.
2. Secure the EXHAUST DUCT ASSEMBLY with two
SCREWS C. See Sketch 2.
SCREW C
C
L
SCREW C
Sketch 2
EXHAUST DUCT
ASSEMBLY,
ALIGN TO FRONT
EDGE OF CABINET
FOR MODELS: RK-52S27 OR RK-52S30
7
1. Place the EXHAUST DUCT ASSEMBLY center
right, off the center of the cabinet opening. Align the front
edge of the duct with the front of the cabinet.
2. Secure the EXHAUST DUCT ASSEMBLY with two
SCREWS C. See Sketch 2.
/32" to the
C
L
Cabinet opening
SCREW C
SCREW C
C
L
Place the
EXHAUST DUCT ASSEMBLY
7
center
the center of the cabinet
opening.
/32" to the right, off
EXHAUST DUCT
ASSEMBLY, ALIGN
TO FRONT EDGE OF
CABINET
Sketch 2
3
STEP 3 FRAME INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening. Plug the POWER
CORD into the electrical outlet.
2. Carefully guide the assembled oven into the prepared opening. Slide the
oven on the EXHAUST DUCT ASSEMBLY. See Sketch 3. Avoid pinching
the cord between the oven and the wall. Adjust the position of the oven
so that the feet of the oven are tted into the recesses of the EXHAUST
DUCT ASSEMBLY and door will open properly. See Sketch 4.
3. Position the Frame Assembly to be square with the oven. Carefully place
the FRAME ASSEMBLY on the oven. Place frame into position. See note
for specic model for placement under Sketch 5. Check that it is level
and then secure with two SCREWS D.
4. Secure the bottom portion of the Frame Assembly with the two remaining
SCREWS D. See Sketch 5.
FOOT
Sketch 3
EXHAUST DUCT
ASSEMBLY
DUCT RECESS
Sketch 4
NOTE FOR FRAME PLACEMENT SKETCH 5
• Model RK-48S27 or RK-48S30 : Align the frame centered to
the oven.
• Model RK-52S27 or RK-52S30 : Align the frame off the right
side of the oven. Folded return is on left side for this frame.
SCREW D
SCREW D
SCREW D
SCREW D
Sketch 5
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
For any other assistance or information about this kit,
please call Sharp’s Customer Assistance Center at
1-800-BE-SHARP (1-800-237-4277)
TINSEB534MRR0
Loading...