Sharp PN-L705H, PN-L805H Operation Manual

Download

Page 1

PN-L705H

LCD MONITOR

OPERATION MANUAL

Page 2

IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

Page 3

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

The lightning ash with arrowhead symbol, within

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is

intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

WARNING:

FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

NOTE:

This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this material may apply, California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/ Others, consult local environmental ofcers.

U.S.A. ONLY

Page 4

DEAR SHARP CUSTOMER

Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or re. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.

1. Read instructions — All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future

reference.

3. Observe warnings — All warnings on the product and in the instructions must be observed closely.

4. Follow instructions — All operating instructions must be followed.

5. Cleaning — Unplug the power cord from the power outlet before cleaning the product. Use a dry cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. Do not use dirty cloths. Doing so may damage the product.

6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result

in accidents.

7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto it. Be careful of equipment which drains water such as an air-conditioner.

8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.

Do not cover or block these vents and openings since insufcient ventilation can cause overheating and/or shorten the life

of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings. Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from

resting on them.

10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the screen breaks.

11. Overloading — Do not overload power outlets or extension cords. Overloading can cause re or electric shock.

12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage ows in the product, and inserting an object can cause electric shock and/or short internal parts.

For the same reason, do not spill water or liquid on the product.

13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualied service person to perform servicing.

14. Repair — If any of the following conditions occurs, unplug the power cord from the power outlet, and request a qualied

service person to perform repairs.

a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls

not described in the instructions can cause damage, which often requires extensive adjustment work by a qualied

technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product

needs servicing.

15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts specied by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in re, electric shock and/or other danger.

16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method recommended by the manufacturer.

18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including ampliers).

Page 5

SAFETY PRECAUTIONS (Continued)

19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

• Use the specied batteries only.

• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the

compartment.

• Do not mix old and new batteries.

• Do not mix batteries of different types. Voltage specications of batteries of the same shape may vary.

• Replace an exhausted battery with a new one promptly.

• If you will not use the remote control for a long time, remove the batteries.

• If leaked battery uid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your

eye well rather than rubbing and seek medical treatment immediately. Leaked battery uid that gets into your eye or your clothing may cause a skin irritation or damage your eye.

20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in low-temperature burns.

22. Do not modify this product.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. An apparatus with CLASS I construction shall be connected to a MAIN socket outlet with a protective earthing connection.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal, D-SUB input terminal, DisplayPort input/output terminals and RS-232C input terminal.

If a monitor is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

• Using xing devices like wall mount brackets recommended by the manufacturer.

• Only using furniture that can safely support the monitor.

• Ensuring the monitor is not overhanging the edge of the supporting furniture.

• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the

monitor to a suitable support.

• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.

• This equipment is not suitable for use in locations where children are likely to be present unsupervised.

Especially for child safety

- Don’t allow children to climb on or play with the monitor.

- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.

- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by

curious children.

Page 6

TIPS AND SAFETY INSTRUCTIONS

The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please

note that these are not malfunctions but common phenomena

of LCDs and will not affect the performance of the monitor.

- Do not display a still picture for a long period, as this could

cause a residual image.

- Never rub or tap the monitor with hard objects.

- Please understand that SHARP CORPORATION bears no

responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

- This monitor and its accessories may be upgraded without

advance notice.

Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam. Do not use in an environment where there are corrosive gases (sulfur dioxide, hydrogen sulde, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this could lead to re.

Ensure that the monitor does not come into contact with water or other uids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to re or electric shock.

- Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.

- Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of re.

- Do not use the monitor in places where it may be exposed to

direct sunlight. Risk of cabinet deformation and failure if the monitor is used in direct sunlight.

- Images cannot be rotated on this monitor.

When using in portrait orientation, you will need to prepare appropriately orientated content in advance.

- The power outlet shall be installed near the equipment and shall be easily accessible.

- Please be sure to constantly remove dust and garbage that

has attached to the ventilation opening. If dust collects in the

ventilation opening or the inside of the monitor, it may lead to excessive heat, outbreak of re, or malfunction. Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.

- Do not touch the screen when the monitor power is turned on, it will lead to a malfunction. When this occurs, turn the monitor power off and then on.

- Do not operate the screen with a hard or pointed object such as a ngernail or pencil.

- Depending on the application used, the touch pen may not

function.

- If another USB device is connected to the computer to which

the touch panel is connected, do not operate the USB device

during touch panel input. Input may not take place correctly.

- Do not allow a cable to come near the screen. This may

cause the touch panel to malfunction.

The Power Cord

- Use only the power cord supplied with the monitor.

- Do not damage the power cord nor place heavy objects on

it, stretch it or over bend it. Also, do not add extension cords.

Damage to the cord may result in re or electric shock.

- Do not use the power cord with a power tap. Adding an extension cord may lead to re as a result of

overheating.

- Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

- Unplug the power cord if it is not used for a long time.

- Do not attempt to repair the power cord if it is broken

or malfunctioning. Refer the servicing to the service representative.

Manual Scope

- Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States

and/or other countries.

- The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the

United States and other countries.

- DisplayPort is a registered trademark of Video Electronics

Standards Association.

- Intel, Celeron, and Intel Core 2 Duo are trademarks or registered trademarks of Intel Corporation or its subsidiaries

in the U.S.A. and other countries.

- RoomView, Crestron RoomView and Crestron Connected are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.

- All other brand and product names are trademarks or registered trademarks of their respective holders.

- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.

- Language of OSD menu used in this manual is English by way of example.

- Illustrations in this manual may not exactly represent the actual product or display.

- This manual assumes use in landscape orientation, except

where specically noted.

LED Backlight

● The LED backlight in this product has a limited lifetime. * If the screen gets dark or does not turn on, it may be

necessary to replace the LED backlight.

* This LED backlight is exclusive to this product and must

be replaced by an authorized SHARP servicing dealer or service center. Please contact an authorized SHARP

servicing dealer or service center for assistance.

Page 7

MOUNTING PRECAUTIONS

Power LED

Cable clamp

Power cord (Supplied)

logo

Logo

• This product is for use indoors.

• A mounting bracket compliant with VESA specications is required.

• Since the monitor is heavy, consult your dealer before

installing, removing or moving the monitor.

• Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or

mishandling.

• Use the monitor with the surface perpendicular to a level surface. If necessary, the monitor may be tilted up to 20 degrees upward.

• When moving this monitor, hold with the handles or at

the sides of this monitor, and hold the top and bottom of this monitor. Do not grasp the screen, monitor corner,

tray, speaker, or speaker cover. This may cause product damage, failure, or injury.

• This monitor should be used at an ambient temperature

between 41°F (5°C) and 95°F (35°C).

• When using the monitor laying at on a surface (when the monitor is tilted more than 20 degrees upward from the

perpendicular in relation to a level surface), use the monitor

at the ambient temperature within the range of 41°F (5°C) to 86°F (30°C).

• Be careful of high temperatures in the surrounding area.

If it is difcult to provide sufcient space for any reason

such as the installation of the monitor inside a housing, or

if the ambient temperature may be outside of the range of 41°F (5°C) to 95°F (35°C), install a fan or take other measures to keep the ambient temperature within the required range.

• Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specied by the optional equipments.

• Do not block any ventilation openings. If the temperature

inside the monitor rises, this could lead to a malfunction.

• Do not place the monitor on a device which generates heat.

• Adhere to the following when installing the monitor in its portrait orientation. Failing to adhere to the following may

cause malfunctions.

- Install the monitor such that the power LED is located on

the bottom side.

Be sure to clamp the power cord (supplied) onto the cable

clamp attachment using the supplied cable clamp. When

clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively.

attachment

Cable clamp

• Use the supplied vertical sticker when you install the

monitor in portrait orientation.

Cover SHARP

Flat installation

• When using the monitor laying at on a surface (when the monitor is tilted more than 20 degrees upward from the

perpendicular in relation to a level surface), consult an

authorized SHARP dealer because there are some specic

mounting conditions.

Adhere to the following. Failing to adhere to the following may cause malfunctions.

- Set HORIZONTAL INSTALLATION in the MONITOR

menu to UPWARD. (See page 36.)

Use the monitor at the ambient temperature within the range

of 41°F (5°C) to 86°F (30°C). Provide 7-7/8 inch (200 mm) or more space between the monitor and the oor or other mounting surfaces and surrounding objects to prevent heat from accumulating inside. If it is difcult to provide sufcient space or if the ambient temperature may be outside of the range of 41°F (5°C) to 86°F (30°C), install a fan or take other measures to keep the ambient temperature within the required range.

- Set the PORTRAIT/LANDSCAPE INSTALL on the

MONITOR menu to PORTRAIT. (See page 36.)

7-7/8 [200]

Unit: inch [mm]

7-7/8 [200]

- Do not press hard on the LCD panel or otherwise subject

it to impacts.

Page 8

Contents

IMPORTANT INFORMATION ............................................3

DEAR SHARP CUSTOMER ..............................................4

SAFETY PRECAUTIONS ..................................................4

TIPS AND SAFETY INSTRUCTIONS ...............................6

MOUNTING PRECAUTIONS ............................................7

Supplied Components .....................................................9

System Requirements .....................................................9

Part Names .....................................................................10

Connecting Peripheral Equipment ...............................12

Connecting the Power Cord .........................................14

Binding Cables ...............................................................14

Preparing the Remote Control Unit ..............................15

Installing the batteries ................................................15

Remote control operation range .................................15

Removing the Handles ..................................................16

Mounting a web camera ................................................16

Turning Power On/Off ....................................................17

Turning on the main power.........................................17

Turning power on .......................................................17

Turning power off .......................................................17

Touch Panel / Touch Pen Preparations ........................19

Connecting the touch pen adapter .............................19

Touch Pen Preparations ............................................. 19

Computer preparations ..............................................19

Touch pen actions ......................................................20

Adding touch pens (pairing) .......................................21

Touch action ...................................................................22

Touch action ............................................................... 22

Other functions ...........................................................24

Cautionary points .......................................................24

Eraser .........................................................................24

Basic Operation .............................................................25

Using the touch menu ................................................25

Using the remote control unit .....................................26

Menu Items .....................................................................29

Displaying the menu screen .......................................29

Conguring settings in the touch menu ......................30

Menu item details .......................................................31

Adjustments for computer screen display ..................42

Initialization (Reset)/Functional Restriction Setting

(FUNCTION) ....................................................................43

Controlling the Monitor with a computer (RS-232C)

Computer connection .................................................44

Communication conditions .........................................44

Communication procedure .........................................44

Setting of the GAMMA user data ................................46

RS-232C command table ...........................................47

Controlling the Monitor with a computer (LAN) ..........54

Settings to connect to a LAN ......................................54

Controlling with a computer ........................................56

[Advanced operation]

Command-based control ............................................63

Troubleshooting .............................................................64

Specications ...............................................................66

Mounting Precautions

(For SHARP dealers and service engineers) ...............71

...44

For information on Touch pen Management Tool, Pen Software and Information Display Downloader, see the manual for each.

Page 9

Supplied Components

If any components are missing, please contact your dealer.

Liquid Crystal Display Monitor: 1



Remote control unit: 1



Cable clamp (insertion type): 4



Cable clamp: 3



Power cord: 1



Remote control unit battery



(R-03 (“AAA” size)): 2

CD-ROM (Utility Disk): 1



SHARP Display Connect License: 1



Setup Manual: 1



Touch pen (for capacitive touch panel): 1



Touch pen adapter: 1



Pen tip for touch pen



(for capacitive touch panel): 2

Touch pen battery (LR-03 (“AAA” size)): 1



Tray: 1



Speaker cover: 2



USB cable: 1



USB extension cable: 1



RS-232C conversion cable (3.5mm mini jack): 1



Eraser (for capacitive touch panel): 1



Camera mount: 1



Camera screw (inch thread): 1



Speaker cover attachment screws (M3)/



Camera mount screws (M3): 6

Touch pen adapter screw (Step screw, M3): 1



Vertical sticker (Logo): 1



Cover SHARP logo: 1



Place this sticker onto the SHARP logo to cover

the logo.

* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.

* For environmental protection!

Do not dispose of batteries in household waste. Follow the disposal instructions for your area.

System Requirements

Connected equipment

Hardware

Must have a USB 2.0 compliant port. CD-ROM drive required for software installation.

Windows 7 (32-bit or 64-bit version), Windows 8.1 (32-bit or 64-bit version), Windows 10 (32-bit or 64-bit version)

Mac OS X v10.11, macOS v10.12 (The touch panel and touch pen operate with the standard driver of OS.)

Google Chrome OS Version 39 or later (The touch panel and touch pen operate with the standard driver of OS.)

Supplied Software (Windows)

CPU

Intel Core m3-7Y30 or faster

Intel Core i5-7Y57 or faster recommended Video Output Must be capable of output at a vertical frequency of 60 Hz or higher Memory At least 4 GB Free space on hard drive At least 200 MB (free space separately required for data storage)

To use the touch panel, the touch panel and computer must be connected, and Touch pen Management Tool, and Pen Software

must be installed on the computer from the supplied CD-ROM.

When the Information Display Downloader is installed, you can check and download the most recent versions of the software

programs.

To install the software, see the manual for each.

The USB port varies depending on the terminal connected to the computer.

DisplayPort 1 input terminal/HDMI 1 input terminal USB 1 port (for touch panel) D-sub input terminal/DisplayPort 2 input terminal/HDMI 2 input terminal/HDMI 3 input terminal USB 2 port (for touch panel)

(Factory setting. Can be changed in TOUCH INPUT SELECT in the SETUP menu.)

SHARP Display Connect setup program and Touch Viewer setup program can be downloaded using Information Display Downloader.

Page 10

Front view

67 7

15 16 21 22 23 24 251817 19 2014

9 10

Part Names

1. Remote control sensor (See page 15.)

2. Power LED (See page 17.)

3. POWER button (See page 17.)

4. TOUCH MENU button (See page 25.)

Rear view

TIPS

• It is convenient to use the terminals for separate purposes; for example, using the terminal on the bottom of the monitor

to connect a xed computer and using the terminal on the

side of the monitor to connect a mobile computer.

Caution

• Consult your SHARP dealer for attachment/detachment of

optional parts.

3 4

5. USB port (for USB device) (USB 2.0 compliant)

To use, remove the seal and connect the USB cable on

the back of the tray (“32”) to the computer. (See page 13.)

6. Tray

7. Speakers

8. Handles

9. Vents

10. Optional attachment section

This section is used to connect optional

hardware for function expansion. Offering this

attachment location is not a guarantee that

future compatible hardware attachments will be

released.

11. Expansion slot

This section is used to connect optional

hardware for function expansion. Offering this

attachment location is not a guarantee that

future compatible hardware attachments will be

released.

12. Main power switch (See page 17.)

13. AC input terminal (See page 14.)

14. External speaker terminals (See page 13.)

15. Audio output terminal (See page 13.)

16. LAN terminal (See page 13.)

17. Optional terminal

This terminal is provided for possible future (optional) function expansion. Offering of this terminal is not a guarantee that future

expanded functionality will be released.

18. RS-232C input terminal (See page 13.)

19. Touch pen adapter port (See page 19.)

20. USB port (See page 13.)

21. USB 1 port (for touch panel) (See page 13.)

22. DisplayPort output terminal (See page 13.)

23. HDMI 1 input terminal (See page 12.)

24. DisplayPort 1 input terminal (See page 12.)

25. Audio input terminal (See page 13.)

26. Terminal for rmware updating

27. USB 2 port (for touch panel) (See page 13.)

28. D-sub input terminal (See page 12.)

29. DisplayPort 2 input terminal (See page 12.)

30. HDMI 2 input terminal (See page 12.)

31. HDMI 3 input terminal (See page 12.)

32. USB cable (See page 13.)

Normally not used.

Page 11

Remote control unit

Part Names

1. Signal transmitter

2. Operation buttons (See pages 26 and 27.)

Page 12

Connecting Peripheral Equipment

14781113101415916

Caution

• Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/

disconnecting cables. Also, read the manual of the

equipment to be connected.

• Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may

cause malfunctions and the other problems.

• Do not use any cable that has a damaged or deformed terminal. Using such cables may cause malfunctions.

TIPS

•

When using a touch panel, connect the USB cable to the computer. For details, see the Touch pen Management Tool Operation Manual.

• Images may not be displayed properly depending on the

computer (video card) to be connected.

• Use the automatic screen adjustment when a computer screen is displayed for the rst time using D-SUB or when the setting of the computer is changed. The screen is adjusted automatically when SELF ADJUST in the

MONITOR menu is set to ON.

• If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed from the audio portion. Audio should be played through this monitor by connecting the playback device to the monitor’s audio input, and connecting the monitor’s audio output to the speakers or

other devices.

• The audio input terminals used in each input mode are

factory-set as follows.

Input mode

HDMI1 HDMI 1 input terminal

HDMI2 HDMI 2 input terminal HDMI3 HDMI 3 input terminal

DisplayPort 1 DisplayPort 1 input terminal DisplayPort 2 DisplayPort 2 input terminal

D-SUB Audio input terminal

Audio input terminal (Factory setting)

It is convenient to use the terminals for separate purposes; For example, using the terminal on the bottom of the monitor

to connect a xed computer and using the terminal on the side

of the monitor to connect a mobile computer.

1. HDMI 1 input terminal

2. HDMI 2 input terminal

3. HDMI 3 input terminal

• Use a commercially available HDMI cable (conforming to

the HDMI standard) that supports 4K.

• Select the audio input terminal to be used in AUDIO SELECT of the SETUP menu.

When HDMI is selected, it is not necessary to connect an

audio cable to the audio input terminal.

4. DisplayPort 1 input terminal

5. DisplayPort 2 input terminal

• Use a commercially available DisplayPort cable (conforming to the DisplayPort standard) that supports

4K.

• Select the audio input terminal to be used in AUDIO SELECT of the SETUP menu.

When DisplayPort is selected, it is not necessary to

connect an audio cable to the audio input terminal.

6. D-sub input terminal

• Set D-SUB of INPUT SELECT on the SETUP menu according to the device to be connected.

Page 13

Connecting Peripheral Equipment

USB port (for USB device)

7. Audio input terminal

• Use an audio cable without resistance.

• Set the audio input terminal to be used in each input mode in AUDIO SELECT on the SETUP menu.

8. DisplayPort output terminal

• The screen displayed on this monitor and the audio output

from this monitor can be output to an external device.

• Use a commercially available DisplayPort cable (conforming to the DisplayPort standard) that supports

4K.

• Outputting HDCP-encrypted video requires an external device which supports HDCP.

• Output of video may not be possible with some versions

of HDCP.

9. Audio output terminal

• The output sound varies depending on the input mode.

• The volume of the output sound can be xed by setting

AUDIO OUTPUT of AUDIO OPTION on the SETUP menu.

• It is not possible to control the sound output from the

audio output terminals with the AUDIO menu.

10. Touch pen adapter port

• Connect the touch pen adapter in order to use the touch

pen. (See page 19.)

11. USB 1 port (for touch panel)

• To use the touch panel with a computer connected to the terminal below, connect the touch panel to the computer with a USB cable. (Factory setting. Can be changed in TOUCH INPUT

SELECT on the SETUP menu.)

- DisplayPort 1 input terminal

- HDMI 1 input terminal

12. USB 2 port (for touch panel)

• To use the touch panel with a computer connected to the terminal below, connect the touch panel to the computer with a USB cable. (Factory setting. Can be changed in TOUCH INPUT

SELECT on the SETUP menu.)

- D-sub input terminal

- DisplayPort 2 input terminal

- HDMI 2 input terminal

- HDMI 3 input terminal

13. USB port

• Use to connect a device when using Pen Software multiboard mode (optional). To build a system, consult your

dealer.

14. RS-232C input terminal

• The monitor can be connected to a computer using the

RS-232C conversion cable (supplied) and a commercially

available RS-232 straight cable to control the monitor from the computer.

15. LAN terminal

• You can control the monitor from a computer on a network by connecting a commercially available LAN cable between this terminal and a network.

16. External speaker terminals

• To use external speakers, set SPEAKER SELECT to

EXTERNAL in AUDIO OPTION on the SETUP menu.

• Be sure to use external speakers with an impedance of 6 Ω or greater and a rated input of at least 10 W.

1. While pushing the tab, insert the tip of the cable.

2. Release the tab.

TIPS

• Be sure to connect the + and - terminals and the left and right speakers properly.

• Avoid short circuiting the + and - terminals.

• When SPEAKER SELECT is set to EXTERNAL, the

internal speakers are disabled.

17. USB cable

• To use the USB port (for USB device) (USB 2.0 compliant) on the front of the tray, connect the USB cable to the USB

port on the computer.

* The touch panel must be connected separately.

Computer

Page 14

Connecting the Power Cord

AC input terminal

For power outlet

Caution

• Use only the power cord supplied with the monitor.

1. Turn off the main power switch.

2. Plug the power cord (supplied) into the AC input terminal.

3. Plug the power cord (supplied) into the power outlet.

Binding Cables

Main power switch

Power cord (Supplied)

The cables connected to the terminals on the rear of the

monitor and the USB cable on the back of the tray can be fastened with the cable clamp.

*1 *2

Cable clamp (insertion type)

Cable clamp attachment

Cable

Cable clamp attachment

Cable clamp

Page 15

Preparing the Remote Control Unit

16.4 feet (5 m)

Installing the batteries

1. Place your nger on the part marked with the ▲, and

then pull the cover off.

2. See the instructions in the compartment and put in the supplied batteries (R-03 (“AAA” size) x 2) with their plus (+) and minus (-) sides oriented correctly.

3. Close the cover.

TIPS

• When the batteries become exhausted, replace them with new (commercially available) batteries.

• The supplied batteries (R-03 (“AAA” size) x 2) may become exhausted quickly depending on how they are stored.

• If you will not be using the remote control for a long time,

remove the batteries.

• Use manganese or alkaline batteries only.

Remote control operation range

The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor.

Remote

10°

10°10°

control sensor

10°

TIPS

• Do not expose the remote control unit to shock by dropping

or stepping on it. This could lead to a malfunction.

• Do not expose the remote control unit to liquids, and do not place it in an area with high humidity.

• The remote control unit may not work properly if the remote

control sensor is under direct sunlight or strong lighting.

• Objects between the remote control unit and the remote control sensor may prevent proper operation.

• Replace the batteries when they run low as this may

shorten the remote control’s operation range.

• If a uorescent light is illuminated near the remote control unit, it may interfere with proper operation.

• Do not use it with the remote control of other equipment

such as air conditioner, stereo components, etc.

Page 16

Removing the Handles

Handle

Handle screws

The handles can be removed.

Caution

• The removable handles and handle screws are for use with this monitor. Do not use them for any other devices.

• To attach handles, be sure to use the handles and handle screws which were removed from this monitor.

• Be sure the handles are attached securely.

Mounting a web camera

It is possible to mount a commercially available web camera in the following positions:

(1)

(1) Attach the supplied camera mount with the supplied

camera mount screws (x2).

(2) Attach the web camera (commercially available) to the

(2)

camera mount with the supplied camera screw (inch thread) (x1).

*1 The camera mount cannot be attached when the tray is

attached. To attach the camera mount, remove the tray mount tting. (See page 72.)

*2 The camera mount cannot be attached when the speaker

cover is attached.

Page 17

Power LED POWER button

Turning Power On/Off

POWER button

Caution

• Turn on the monitor rst before turning on the computer or playback device.

• When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction.

Turning on the main power

Main power switch

Turning power off

Turning power off with monitor buttons

1. Touch the POWER button.

The recognition screen appears.

2. Touch [OK].

The power is turned off. (Standby mode)

TIPS

• If about 15 seconds elapses while the recognition screen appears, the power will automatically turn off.

Turning power off with remote control unit

Caution

• The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on.

• For a complete electrical disconnection, pull out the main plug.

Turning power on

Press the POWER button or MONITOR ON button to turn the

power ON.

Status Status of the monitor

Blue lit Power on Orange lit Power off (Standby mode)

Blue ashing Input signal waiting mode

1. Press the POWER button or MONITOR OFF button.

The power is turned off. (Standby mode)

TIPS

• When the main power switch is off, the monitor cannot be

turned on.

• If the monitor is in input signal waiting mode and you press the POWER button, the monitor enters standby mode.

• To disable the logo screen from displaying when turning the power ON, set LOGO SCREEN to OFF on the OTHERS

menu. (See page 38.)

TIPS

• You can x the input mode that appears after startup. Set

START INPUT MODE on the SETUP menu.

Page 18

Turning Power On/Off

Date/time setting

• If the time has yet to be set when the monitor is rst turned on, the date/time setting screen appears. Set the date and

time.

DATE/TIME SETTING

: :

01 01 17/12 AM00

:/ 20

OK:[ENTER] CANCEL:[RETURN]

(1) Press the or button to select the date and time,

and press the

or button to change the numerical

values.

(2) Press the ENTER button.

• Be sure to set the date and time.

• The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the SETUP menu when the date/time setting screen

disappears.

TIPS

• Set the date in “Month/Day/Year” order.

• Set the time on a 12-hour basis.

• The clock is maintained by the internal battery.

• If you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local SHARP servicing dealer or service center for assistance with battery replacement.

• Estimated service life of the internal battery: About 5 years

(depending on monitor operation)

• The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its

expected operation life.

Page 19

Touch Panel / Touch Pen Preparations

uch pen

(antitheft)

T adapter por

Battery cover

Connecting the touch pen adapter

To use the touch pen, insert the touch pen adapter into the touch pen adapter port on the monitor.

ouch pen

adapter scre

Touch pen adaptor

Touch Pen Preparations

Inserting the battery

1. Remove the battery cap and main cover.

TIPS

• The supplied battery (LR-03 (“AAA” size)) may be exhausted in a short time, depending on how it was stored.

• If the touch pen will not be used for an extended time, remove the battery from the touch pen.

• For the battery, use an alkaline battery.

Computer preparations

To use the touch panel, the touch pen and the eraser, install

the software below.

• Touch pen Management Tool

• Pen Software

To install the software, see the manual for each.

Battery capMain cover

2. Open the battery cover and insert the supplied battery (LR-03 (“AAA” size) x 1) into the touch pen.

Check the plus (+) and minus (-) markings on the inside of the touch pen and insert the battery in the correct

orientation.

3. Replace the battery cover and main cover.

While pressing the battery cover, replace the main cover.

4. Replace the battery cap.

Page 20

Function button 1 Function button 2 Pointer part

Function button 3Function button 4LED

Pen tip

Touch Panel / Touch Pen Preparations

Touch pen actions

Only use touch pens that are used with this monitor (supplied touch pens or optional PN-ZL06).

• Function button 1 : Pen Software Link

• Function button 2 : PageDown

• Function button 3 : PageUp

• Function button 4 : Left click/Pointer (See the description

on the right.)

You can change the functions that are assigned to the function buttons. For details, see the Touch pen Management Tool Operation Manual.

TIPS

• In Mac and Chrome OS, function buttons below can be

used.

- Function button 2 : PageDown

- Function button 3 : PageUp

- Function button 4 : Left click

Using as a digitizer pen

A touch pen can be used as a Windows digitizer pen. To use a touch pen as a digitizer pen, change the “Touch Operation Mode Setting” to “Pen digitizer Mode” in the

Touch pen Management Tool. For details, see the Touch pen Management Tool Operation Manual.

However, Pen Software Link that is assigned to the function button 1 is cannot be used. (When the pen is a digitizer pen.)

LED

Status Status of the touch pen

Lights off Standby mode White ashing Operation mode* Orange ashing Battery is low Blue ashing Not connected to pen adapter

If the touch pen is not moved for an extended time, it

automatically enters the standby mode and the LED turns off. (Factory setting. When the touch pen is moved, it automatically enters operation mode.) * You can change how the LED lights when the touch pen is in

operation mode. For details, see the Touch pen Management Tool Operation Manual.

In the Pen Software, the LED lights in the set touch pen color. For details, see the Pen Software Operation Manual.

Pointer

You can use the touch pen as a pointer.

1. Point the pointer part of the touch pen toward the screen.

2. While pressing function button 4, move the touch pen.

• The pointer icon appears on the screen, and moves as the touch pen is moved.

• To stop the pointer, release the function button 4.

You can change the pointer icon setting while using the pointer function (while pressing function button 4).

• Function button 2 while pressing function button 4 :

The shape of the pointer icon changes.

• Function button 3 while pressing function button 4 :

The color of the pointer icon changes. For details, see the Touch pen Management Tool Operation Manual.

TIPS

• Hold the touch pen at the part indicated below. Incorrect operation may result if your nger is too close to the tip of

the pen.

• Hold the touch pen with your bare hand.

The screen will not respond if you wear a glove.

• If the LED blinks orange, the battery is low. Promptly replace with a battery (commercially available). If the LED does not illuminate, check if the battery is

depleted.

• Use function buttons near the front of the screen. If too far

away, operation will not be possible.

• Press function buttons slowly and rmly. If pressed too quickly, the action may not be recognized.

• The line may break if the touch pen battery is low or there is other wireless equipment in operation nearby.

• The touch pens cannot be used as touch pens and digitizer

pens at the same time. When the setting is changed in the Touch pen Management Tool, all touch pens become

digitizer pens. Multiple digitizer pens cannot be used at the

same time.

Touch pen settings

Touch pen settings are congured using the Touch pen Management Tool. For details on the settings and how to use the utility, see the Touch pen Management Tool Operation

Manual.

Palm cancel function

When you write with the touch pen, you can set the touch panel to not respond when your hand touches the screen. (See

page 36.)

Page 21

Replacing the pen tip

Pen tip cover

Pen tip

If the pen tip becomes worn or damaged, replace it.

1. Remove the pen tip cover.

2. Remove the pen tip.

* Do not touch any part other than the pen tip.

3. Attach the pen tip cover.

Touch Panel / Touch Pen Preparations

Adding touch pens (pairing)

• Up to 4 touch pens can be used simultaneously. (Up to 8

touch pens can be registered.)

Item Model Remarks

Touch pen PN-ZL06 For capacitive touch panel

• To use an optional touch pen with the monitor, the touch

pen must be registered in the touch pen adapter. (pairing)

• Use the Touch pen Management Tool to perform touch pen pairing. For details, see the Touch pen Management Tool Operation Manual.

• Perform touch pen pairing for one pen at a time.

TIPS

• When multiple touch pens are used, touch positions and

touch pen information (color, thickness, etc.) may become interchanged, and lines may break.

- When touched simultaneously.

- When touch pens are moved near each other.

- When batteries are low.

- When other wireless equipment is operating nearby.

• Do not press the pen tip on other than the screen.

This may cause malfunctioning.

• One touch pen cannot be registered in multiple touch pen adapters.

* Take care that the pen tip cover does not catch on the

metal.

4. Insert the pen tip.

* Note carefully which end of the pen tip you are inserting.

Insert the at end of the pen tip.

* Firmly insert the pen tip all the way in.

Page 22

Touch action

Touch actions that can be used with this monitor differ according to operating system and application. The functions of touch actions are also different. For details, check OS Help

and the application’s support documentation.

Windows 8.1 /

Touch action

Single-tap Yes Yes Yes

Double-tap Yes Yes Yes

Swipe Yes Yes No Swipe from edge

of screen

Drag-and-drop Yes Yes Yes Flicks Yes Yes No

Press-and-hold Yes Yes No

Slide to pan Ye s Ye s No

Zoom* Yes Yes Yes

Press-and-tap* No Yes No

Rotate* Ye s Ye s No

* Cannot be used when TOUCH OPERATION MODE is set

to SINGLE-TOUCH MODE.

Yes No No

Windows 7 Chrome OS

Double-tap

Same action as double-clicking a mouse. Quickly touch twice with your nger/touch pen.

When double-tapping with your nger, be sure to lift your nger sufciently off the screen after the rst tap. If there is insufcient distance between the screen and your nger, double-tap will not take place.

Swipe

Touch the screen with your nger/touch pen, move without

lifting, and then stop.

TIPS

• On the Mac, the actions are the equivalent mouse actions.

• In Windows 7, if the checkmark has been removed from “Enable multi-touch gestures and inking” in “Pen and touch” in Control Panel, select the checkbox.

• For the procedures for using the touch pen in the Pen

Software, see the Pen Software Operation Manual.

Common nger and touch pen actions

Single-tap

Same action as left-clicking a mouse. Touch with your nger/touch pen.

Swipe from edge of screen

After touching the edge of the monitor with your nger/touch pen, move horizontally without releasing your nger/touch pen

and then stop.

Page 23

Touch action

Drag-and-drop

Same action as drag-and-drop with a mouse. Touch the screen with your nger/touch pen and move without

lifting. When you have nished the movement, lift your nger/ touch pen.

Flicks

Flick your nger/touch pen in the direction of the function you want to use.

Flick your nger

Finger actions

Zoom

Use in a screen that is capable of enlargement/reduction. Touch the screen with two ngers and move your ngers closer together to reduce the view, or apart to enlarge the view.

Reduction

Press-and-hold

Same action as right-clicking a mouse. Press briey with your nger/touch pen, and then lift your

nger/touch pen from the screen.

Slide to pan

With your nger/touch pen touching the screen, move it up and down to scroll the screen.

Enlargement

Press-and-tap

Same action as right-clicking a mouse. With one nger touching the screen, tap once (single tap) with another nger.

Tap once (single tap) with another nger

With one nger touching

Page 24

Touch action

The main body

Rotate

Use this action in a screen that is capable of image rotation.

Touch the center point of the rotation with one nger. While holding that nger still, move another nger in the desired

direction of rotation.

Move another nger in the

desired direction of rotation

With one nger touching

TIPS

•

The screen may not respond correctly in the following cases:

- Touch gesture is too quick.

- The distance between the two points is too short.

- The two points intersect.

Other functions

In Windows 8.1/10, input panel functions can be used. In Windows 7, touch pointer and input panel functions can be

used.

For information on these functions, see Windows Help.

Touch pointer :

A translucent image of a mouse appears near the point

touched. The left/right buttons of the image can be clicked to perform the same actions as left/right clicking a mouse.

Input panel :

A software keyboard and an input panel with handwriting

recognition appear on the screen.

Windows 8.1/10 and Windows 7 (excluding Starter), the ink function of Microsoft Ofce can be used.

Handwritten comments can be written, and handwriting can be recognized. For details, see Microsoft Ofce Help.

Eraser

Only use an eraser that is supplied with this monitor. The eraser is used with the Pen Software. For the procedure for using the eraser, refer to the Pen Software Operation Manual.

Caution

• Hold the main body of the eraser with your bare ngers. The screen will not respond if you are wearing a glove.

• Slowly place the large face of the eraser fully on the screen. Insufcient contact may prevent the eraser from being recognized. Touching the screen with one of the noncloth sides will damage the screen.

•

If there is any dirt or foreign matter on the surface that contacts the screen, remove it. Foreign matter may damage the screen.

• Place the eraser on the screen inside the display area. If the eraser rst touches the frame (outside the display area) and then is moved inside the display area, the screen will

not respond.

Cautionary points

• Note the following when touching by nger:

- Do not touch with a wet nger.

- Touch with the ball of your nger.

- Touch with your bare nger. The screen will not respond if you are wearing a glove.

• Do not use the touch pen for any purpose other than touch

panel operation.

• Do not press hard on the pen tip.

• This may not operate correctly if there is an inverter uorescent light nearby.

• Do not store with the pen tip of the touch pen or function button pressed. The battery will be exhausted.

• If there is dirt or foreign matter on the tip of the touch pen,

remove it. Foreign matter may damage the screen.

• The touch pen position may occasionally deviate in the login screen. In this case, use the keyboard or mouse.

• If the USB cable becomes disconnected, the touch

panel may not operate correctly after the USB cable is

reconnected. In this case, restart the computer.

• When the “Touch Operation Mode Setting” of the Touch pen

Management Tool is “Pen digitizer Mode”:

- Even if you use the eraser in the Pen Software, the eraser will be the standard size eraser.

- The eraser can be used in the software below. Microsoft Ofce 2007/2010/2013/2016

Page 25

Basic Operation

TOUCH MENU button

Using the touch menu

You can touch the screen to change input mode, volume, and other settings.

1. Touch the TOUCH MENU button.

2. Touch the screen to change settings.

INPUT

SIDE INPUT TERMINAL

D-SUB

DisplayPort2

HDMI2

HDMI3

BOTTOM INPUT TERMINAL

HDMI1

DisplayPort1

(8) (1) (2) (3) (4) (5) (6) (7)

(2) Volume adjustment

Adjusts the volume.

Increases the volume.

Decreases the volume. Mutes the sound.

Touch again to return the sound to the original volume.

(3) Settings

Adjust video and congure settings for quad screen and touch operation. (See page 30)

(4) Backlight off

Turn off the backlight. When the backlight is off, the icon changes to the backlight

on icon (

). Touch to turn on the backlight.

(5) FREEZE

Freezes the video shown on the monitor. To cancel, press any button other than the POWER button,

MUTE button or VOLUME button.

Freeze is also canceled when the input signal changes (switching to no signal, changing the resolution, etc.). In some cases a residual image may occur. Do not freeze

the video for a long time.

(1) Input mode selection

Changes the input mode.

Input mode Video Audio

DisplayPort 1 DisplayPort 2 HDMI1 HDMI1 input terminal

HDMI2 HDMI2 input terminal HDMI3 HDMI3 input terminal D-SUB[RGB] D-SUB[COMPONENT] OPTION

DisplayPort 1 input terminal DisplayPort 2 input terminal

D-sub input terminal

Expansion slot

Audio input terminal

• When the input mode is changed, the touch panel

connection also changes. You can set whether the side

or bottom USB port is used in each input mode. (See

page 35.)

*1 This is displayed when you have used the expansion slot

to expand the functions.

*2 Select the terminal for AUDIO SELECT which is used for

audio input. (See page 34.)

(6) QUAD-SCREEN ON

You can display 4 screens at once. (See page 39.) When quad-screen is displayed, the icon changes to the

QUAD-SCREEN OFF icon (

(7) RECONFIGURE QUAD-SCREEN

The 4 screens set in SETTING INITIAL SCREEN (see

page 37) are displayed.

(8) Exit touch menu

Closes the touch menu.

TIPS

• The touch menu can also be used with the remote control

unit.

(1) Hold down the INFORMATION button at least 5

seconds.

The touch menu appears.

(2) Select the setting item with the

(3)

Set with the or button, and press the ENTER

or button.

button.

- The setting is entered.

- Press the RETURN button to exit the touch menu.

Page 26

Basic Operation

Using the remote control unit

4. MODE (Color mode selection)

Each time you press this button, the color mode changes in the following order:

STD (Standard) → VIVID → sRGB → HIGH ILLUMINANCE → STD...

• HIGH ILLUMINANCE is a display with colors suited to

bright locations.

•

sRGB cannot be used when input mode is D-SUB[COMPONENT].

sRGB is international standard of color representation

specied by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal’s characteristics and represents color tone

close to its original image.

5. VOLUME +/- (Volume adjustment)

Pressing + or - displays the VOLUME menu.

1. HDMI

Switch the input mode to HDMI1, HDMI2 or HDMI3.

2. Numeric input buttons

Use for the following tasks. (0 to 9)

• To set the remote control number.

• To set the IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY.

3. MUTE

Turns off the volume temporarily. Press the MUTE button again to turn the sound back to the

previous level.

Press + or - to adjust the volume.

* If you do not press any buttons for about 4 seconds, the

VOLUME menu automatically disappears.

Page 27

Basic Operation

LAN

BRIGHT 15

6. INFORMATION

Displays monitor information.

INFORMATION1

INPUT MODE SIZE COLOR MODE BRIGHT VOLUME REMOTE No. MODEL VERSION S/N STATUS TOUCH PANEL

LAN

3840 x 2160

INFORMATION2

RS-232C/LAN SELECT DHCP CLIENT IP ADDRESS SUBNET MASK DEFAULT GATEWAY MONITOR NAME DATA PORT MAC ADDRESS

LAN

3840 x 2160

V: 30 Hz H: 67.5 kHz

01/01/2017 SUN 12:00:00 AM

HDMI1

WIDE

STD

PN-L705H

×.×.××.×

xxxxxxxx

0000-000000-00-0000

01/01/2017 SUN 12:00:00 AM

LAN

OFF

192.168.150. 2

255.255.255. 0

0. 0. 0. 0

PN-L705H

10008

XX-XX-XX-XX-XX-XX

10. Buttons for operating the HDMI-connected device

When HDMI CEC LINK is set to AUTO, use these buttons to operate the device connected through the HDMI interface.

11. ID SET

Set a number on the remote control unit. (See page 41.)

12. OPTION

Switch the input mode to OPTION when you have used the

expansion slot to expand the functions.

END:[RETURN]NEXT:[ ]

13. DP (DisplayPort)

Switch the input mode to DisplayPort.

14. SIZE (Screen size selection)

The menu is displayed.

Press the

or button to select the screen size. (See page

29.)

15. PIP/PbyP

The menu is displayed.

Press the

or button to select PIP MODES/

QUAD-SCREEN MODE.

END:[RETURN]NEXT:[ ]

16. BRIGHT +/- (Brightness adjustment)

Pressing + or - displays the BRIGHT menu.

The display changes from INFORMATION1 → INFORMATION2 → INFORMATION3 → clear display, and so on every time you press this button. When displaying INFORMATION, the display changes from INFORMATION1 → INFORMATION2 → INFORMATION3 → INFORMATION1, and so on every time you press the button. Pressing the RETURN button disappears the display.

• INFORMATION3 shows the information when you have

used the expansion slot to expand the functions.

• The display disappears automatically after about 15

seconds.

•

is displayed during LAN communication.

• If

is displayed in red, there is a duplicate IP address.

7. FUNCTION

Use this to display the FUNCTION menu. (See page 43.)

8. ENTER

Conrms the setting.

9. FREEZE

Freezes the video shown on the monitor. To cancel, press any button other than the POWER button,

MUTE button or VOLUME button.

Freeze is also canceled when the input signal changes (switching to no signal, changing the resolution, etc.). In some cases a residual image may occur. Do not freeze the

video for a long time.

Press + or - to adjust the brightness.

* If you do not press any buttons for about 4 seconds, the

BRIGHT menu automatically disappears.

17. INPUT (Input mode selection)

The menu is displayed.

Press the

or button to select the input mode, and press

the ENTER button to enter.

* For input modes that can be changed, see “Using the touch

menu”. (See page 25.)

18. MENU

Displays and turns off the menu screen. (See page 29.)

19. Cursor

These buttons are used to perform operations such as

selecting items, changing adjustment values, and moving the

cursor.

20. RETURN

Returns to the previous screen.

Page 28

Basic Operation

Switching the screen size

Even when the screen size is changed, the display may remain the same depending on the input signal.

WIDE

ZOOM 1

ZOOM 2

NORMAL

Dot by Dot

Displays image so it lls the entire screen.

The image is enlarged to ll the entire screen without changing the aspect ratio. The edges of the image may be cut off.

Use this size if ZOOM 1 cuts off the subtitles.

Displays the image so it lls the screen without changing the aspect ratio.

Displays the dots of the input signals as the corresponding dots on the screen.

TIPS

• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful.

• When dual-screen or quad-screen display is selected, the screen size cannot be changed.

• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original image (e.g. TV broadcast or video input from external equipment).

• When 4:3 video is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the video may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to NORMAL.

• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Depending on the original image size, black bands may remain at the edges of the screen.

Page 29

Menu Items

Displaying the menu screen

Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See page 31 for details of each menu items.

Caution

• Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press the MENU button to display the menu screen.

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

MULTI/PIP

OTHERS

SCREEN D-SUB[RGB]

AUTO

CLOCK

PHASE

H-POS

V-POS

H-SIZE

V-SIZE

RESOLUTION SETTING

INPUT SIGNAL

RESET

1 920x1080

V: 60 Hz H: 67.5 kHz

600

610

OK:[ENTER] END:[RETURN]

TIPS

• The menu will differ depending on the input mode.

• The menu screen will close automatically if no operation is performed for about 15 seconds. (DATE/TIME SETTING, SCHEDULE and LAN SETUP screens will close in about 4

minutes.)

Menu screen display

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

MULTI/PIP

OTHERS

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

1 920x1080

30 30 30 12

V: 60 Hz H: 67.5 kHz

D-SUB[RGB]

BACK:[RETURN]MOVE OSD:[INFORMATION]

1 Name of the menu

2 Input mode 3 An item being selected (highlighted) 4 Screen resolution of input signal, and other data.

2. Press the or button to select PICTURE, and press the ENTER button.

3. Press the

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

MULTI/PIP

OTHERS

or button to select CONTRAST.

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

1 920x1080

V: 60 Hz H: 67.5 kHz

30 30 30 12

D-SUB[RGB]

BACK:[RETURN]MOVE OSD:[INFORMATION]

4. Press the or button to adjust the setting.

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

MULTI/PIP

OTHERS

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

D-SUB[RGB]

30 30 30 12

TIPS

• Items that cannot be selected appear in gray. (e.g. Function not supported by the current input signal)

1 920x1080

For items that have , press the ENTER button, make settings and then press the RETURN button.

V: 60 Hz H: 67.5 kHz

BACK:[RETURN]MOVE OSD:[INFORMATION]

5. Press the MENU button to close the menu screen.

Page 30

TOUCH MENU button

Menu Items

Conguring settings in the touch menu

You can congure the following settings from the touch menu. You can congure the settings by touch operation.

PICTURE BRIGHT page 32

CONTRAST BLACK LEVEL COLOR MODE

CONFIGURE QUAD-SCREEN

OTHERS PORTRAIT/

SETTING INITIAL SCREEN

PRIORITY: AUTO

INPUT SEL.

SAVE LAST INPUT

CONFIG.

TARGET: SOUND /

INPUT SEL.

LANDSCAPE INSTALL LANGUAGE page 34 TOUCH INPUT

SELECT TOUCH OUTPUT

INVALID DISP.

TOUCH OPERATION MODE

PALM CANCEL MODE TOUCH PANEL MODE TOUCH OPERATION See right

page 37

page 36

page 35

page 36

4. Touch the icon in CONTRAST to adjust the setting.

For items that show the >> icon, touch the >> icon to congure the setting in the menu that appears, and then touch the BACK icon.

5. Touch the Exit Touch Menu icon (

TOUCH OPERATION

Use this setting to enable or disable touch operation.

TIPS

• When the input mode is changed, the disable touch action setting is canceled.

• When TOUCH OUTPUT INVALID ICON is set to ON and touch action is disabled, the TOUCH OUTPUT INVALID icon appears in the screen.

• You can touch the TOUCH OUTPUT INVALID icon in the screen to enable touch action.

• The position of the TOUCH OUTPUT INVALID icon can be changed. (See page 36.)

• The TOUCH OUTPUT INVALID icon appears even when a USB cable is not connected.

• When a color pattern is displayed in quad-screen display, the TOUCH OUTPUT INVALID icon does not appear.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Touch the TOUCH MENU button.

2. Touch the Settings icon ( ).

3. Touch the PICTURE tab.

PICTURE

BRIGHT 30 CONTRAST BLACK LEVEL

COLOR MODE

CONFIGURE QUAD-SCREEN

30 30

STD

OTHERS

Page 31

Menu Items

Menu item details

The menu will differ depending on the input mode.

SCREEN

You can move the menu screen display position each time the INFORMATION button is pressed.

AUTO (D-SUB[RGB])

The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing the ENTER button performs adjustment. Use this automatic adjustment when you use the D-SUB[RGB] to display a computer screen for the rst time or when you change the setting of the computer. (See page 42.)

CLOCK (D-SUB[RGB])

Adjusts frequency for sampling clock for applicable video. Adjust when there is ickering in the form of vertical stripes. When using the adjustment pattern (see page 42), make adjustments so that no vertical stripe noise appears in it.

PHASE (D-SUB[RGB])

Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/or there are ickers at corners. When using the adjustment pattern (see page 42), make adjustments so that no horizontal stripe noise

appears in it.

H-POS

Adjust the horizontal position of the image.

V-POS

Adjust the vertical position of the image.

H-SIZE

Adjust the horizontal size of the image.

V-SIZE

Adjust the vertical size of the image.

RESOLUTION SETTING (D-SUB[RGB])

H-RESOLUTION

Sets proper horizontal resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

V-RESOLUTION

Sets proper vertical resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

INPUT SIGNAL (D-SUB[RGB])

If the resolution of the computer is one of the following, make a selection from the following options.

480 LINES .......... AUTO, 640x480 or 848x480

768 LINES .......... AUTO, 1024x768, 1280x768 or 1360x768

1050 LINES ........ 1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 40.)

RESET

Resets the values of the SCREEN menu items to the factory default settings. Select ON and then press the ENTER button.

Page 32

Menu Items

PICTURE

You can move the menu screen display position each time the INFORMATION button is pressed.

BRIGHT

Adjusts the backlight brightness. (In PIP mode, the main side setting is reected in the image.)

CONTRAST

Adjusts the difference between the bright and dark portions of the image.

BLACK LEVEL

Adjusts the entire brightness of the video signals.

TINT

Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.

COLORS

Adjusts the color intensity.

SHARPNESS

Adjusts the sharpness of the image.

COLOR ADJUSTMENT

COLOR MODE

Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See page 26 for details.) * sRGB cannot be used when input mode is D-SUB[COMPONENT].

WHITE BALANCE

THRU ..............Displays the input signal level as is.

PRESET .......... Selects the color temperature using PRESET.

USER .............. Adjusts R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively using USER.

PRESET

Selects the color temperature when the WHITE BALANCE is set to PRESET. The setting values are shown for reference. The color temperature of the screen varies over time. This function is not intended to keep the color temperature constant.

USER

Adjusts each item when the WHITE BALANCE is set to USER.

R-CONTRAST .... Adjusts bright-toned red component.

G-CONTRAST ... Adjusts bright-toned green component.

B-CONTRAST .... Adjusts bright-toned blue component.

R-OFFSET ......... Adjusts dark-toned red component.

G-OFFSET ......... Adjusts dark-toned green component.

B-OFFSET ......... Adjusts dark-toned blue component.

COPY TO USER

Copies the value of PRESET to the USER setting. Select ON and then press the ENTER button.

(In the case other than white, color tone may differ from the PRESET.)

GAMMA

Selects the gamma. USER sets the gamma to the sent value. (See page 46.)

FLESH TONE

Adjust the hue control.

C.M.S.-HUE

Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

C.M.S.-SATURATION

Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

Page 33

Menu Items

ADVANCED

AUTO (D-SUB[RGB])

The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. Pressing the ENTER button performs adjustment.

ANALOG GAIN (D-SUB[RGB])

Adjusts the bright portions of the video input signal.

ANALOG OFFSET (D-SUB[RGB])

Adjusts the dark portions of the video input signal.

Reduce the image noise.

Setting a higher level reduces more noise. However, it may cause blurring on an image.

RGB INPUT RANGE (HDMI/D-SUB[RGB]/DisplayPort/OPTION)

Sets the RGB input signal range.

When using HDMI, DisplayPort or OPTION set to AUTO, the input signal range is detected automatically. Use AUTO normally. If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the setting is different, images will be displayed with washed out blacks and compressed gradients.

DISPLAY COLOR PATTERN

Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting the image. When WHITE, RED, GREEN, or BLUE is displayed, you can set the level in the range of 0 to 255.

OFF ...............No pattern display.

WHITE ...........White single color pattern display.

RED...............Red single color pattern display.

GREEN .........Green single color pattern display.

BLUE .............Blue single color pattern display.

USER ............Red/green/blue mixed color pattern display. When USER is selected, set each color’s level.

RESET

Resets the values of the PICTURE menu items to the factory default settings.

Select ON and then press the ENTER button.

AUDIO

TREBLE

Adjusts the volume of treble-level sound.

BASS

Adjusts the volume of bass-level sound.

BALANCE

Adjusts the balance of the audio sound between right and left.

RESET

Resets the values of the AUDIO menu items to the factory default settings.

Select ON and then press the ENTER button.

Page 34

Menu Items

SETUP

DATE/TIME SETTING

Set the date and time. Press the numerical values.

Set the date in “Month/Day/Year” order. Set the time on a 12-hour basis. (Factory default)

DATE/TIME FORMAT

Sets the date/time display format.

DATE ..................MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD

TIME ...................Select 12- or 24-hour time.

SCHEDULE (See page 40.)

You can turn the power on/off and change the screen brightness at a specied time.

LANGUAGE

Sets the display language for the menu screen.

INPUT SELECT

D-SUB

Select the input mode to be used in D-Sub input terminal.

HDMI CEC LINK

AUTO ............Use the HDMI CEC function.

OFF ...............HDMI CEC function is not used.

AUTO POWER ON

This can be set when HDMI CEC LINK is set to AUTO. If the device connected to the HDMI input terminal supports CEC, you can specify whether or not the monitor power turns on when the device power is turned on.

HDMI AUTO VIEW

When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the HDMI1 to HDMI3 input terminals and expansion slot (when the expansion function is used).

DisplayPort STREAM

Set how DisplayPort is used. If a device that is not DisplayPort1.2 compliant is connected, set to SST1.

SST1 ....Use as single stream (DisplayPort1.1).

SST2 ....Use as single stream (DisplayPort1.2).

MST ...... Only DisplayPort2 can be set.

HDMI MODE

Use MODE1 normally. If video is not displayed correctly when one of the HDMI1 to HDMI3 input terminals is used, such as when a device that is

not 4K compliant is connected, set to MODE2.

Also set MODE2 when the connected device supports 4K but only supports vertical frequencies 50/60 Hz and YCbCr 4:2:0.

INPUT MODE NAME

For each terminal, you can change the input mode name that is displayed during input mode selection or display. The names of INPUT1 to INPUT6* can be changed. (*Factory default.)

(1) Select the input mode name (INPUT1 to INPUT6) that you want to change, and press the ENTER button. If the input mode name can be changed, “EDIT: [ENTER]” will appear.

(2)

Move the cursor to the character that you want to change with the or button, and change the character with the or button.

Change the character type with the MODE button (upper case alphabet, lower case alphabet, numbers, symbols). (3) When you have nished the change, press the ENTER button. Up to 18 characters can be used.

AUDIO SELECT

Selects the terminal used to input audio signals in each input mode.

(YYYY: Year, MM: Month, DD: Day)

If the device connected to the HDMI input terminal supports CEC, the input mode of the monitor changes to

HDMI when playback starts on the device.

Use as multi-stream (DisplayPort1.2). (This may not display correctly, depending on the computer (video card) that is connected.)

or button to select the date and time, and press the or button to change the

Page 35

Menu Items

AUDIO OPTION

SPEAKER SELECT

Selects the speaker to be used.

AUDIO OUTPUT

Sets the volume of sound output from the audio output terminals.

When set to VARIABLE 2, sound will not be output from the built-in speaker or the external speaker terminal.

VARIABLE1 ........ You can adjust the volume using VOLUME.

VARIABLE2 ........ You can adjust the volume using VOLUME.

FIXED................. Fixes the sounds.

AUDIO INPUT LEVEL

Selects the maximum audio input level of the audio input terminal.

MONAURAL AUDIO

Outputs audio signals as monaural.

TOUCH INPUT SELECT

These settings enable use of the touch panel according to input mode selection.

BOTTOM USB

Sets the input mode for use of the touch panel, which is connected to the USB port at the bottom of the monitor. In the landscape orientation, select the terminal into which the video signal of the computer connected to the USB 1 port will be input. When BOTTOM INPUT TERM. is selected and the input mode is DisplayPort 1, or HDMI1, the touch panel can be used with the computer connected to the USB 1 port. In the portrait orientation, select the terminal into which the video signal of the computer connected to the USB 2 port will be input. When BOTTOM INPUT TERM. is selected and the input mode is DisplayPort 2, HDMI2, HDMI3, or D-SUB, the touch panel can be used with the computer connected to the USB 2 port.

When “-“ is selected, the touch panel cannot be used.

SIDE USB

Sets the input mode for use of the touch panel, which is connected to the USB port at the side of the monitor. In the landscape orientation, select the terminal into which the video signal of the computer connected to the USB 2 port will be input. When SIDE INPUT TERM. is selected and the input mode is DisplayPort 2, HDMI2, HDMI3, or D-SUB, the touch panel can be used with the computer connected to the USB 2 port. In the portrait orientation, select the terminal into which the video signal of the computer connected to the USB 1 port will be input. When SIDE INPUT TERM. is selected and the input mode is DisplayPort 1, or HDMI1, the touch panel can be used with the computer connected to the USB 1 port.

When “-“ is selected, the touch panel cannot be used.

START INPUT MODE

You can set the input mode that will be in effect when the power is turned on. When this is set to LAST INPUT MODE, the input mode when the power was last turned off will appear.

* When NO SIGNAL AUTO INPUT SEL is ON and there is no input signal in the set input mode, the input mode will change to

the input mode that has an input signal.

COMMUNICATION SETTING

RS-232C/LAN SELECT

Selects the method with which to control the monitor from the computer.

BAUD RATE

Selects the communication speed used for RS-232C communication.

LAN SETUP

Congures the settings to control the monitor from the computer via LAN. (See page 54.)

Crestron Connected

Select this when using a Crestron device. When this function is set to ON, the monitor can be controlled via network using equipment and application software of Crestron Electronics, Inc. This monitor supports application software RoomView from Crestron Electronics, Inc. This is a function to connect a system developed by Crestron Electronics, Inc. which manages and controls multiple system devices connected to the network. For details of Crestron Connected, refer to the Crestron Electronics, Inc. website. (Provided only In English.)

http://www.crestron.com/

For the download of RoomView Express, refer to the Crestron Electronics, Inc. website. (Provided only In English.)

http://www.crestron.com/getroomview

REMOTE No.

Sets the number of the remote control unit. (See page 41.)

Page 36

Menu Items

MONITOR

PORTRAIT/LANDSCAPE INSTALL

Select the installation direction of the monitor.

LANDSCAPE ............Landscape orientation

PORTRAIT ...............Portrait orientation

HORIZONTAL INSTALLATION

OFF ....................Portrait/landscape installation

UPWARD ............The display screen faces up.

OSD H-POSITION

Adjusts the horizontal display position of menu screen.

OSD V-POSITION

Adjusts the vertical display position of menu screen.

POWER SAVE MODE

When OFF is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode. When ON is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. If set to ON, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled.

OFF IF NO OPERATION

Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, RS-232C commands, or LAN. When the setting is ON, set the time until standby mode is entered in TIME.

POWER ON DELAY

When ON is set, you can delay the screen display after the monitor is turned on. When ON is selected, set the delay time with INTERVAL (interval can be set up to 60 seconds in units of 1 second).

When this function is activated, the power LED ashes (at approx. 0.5 second interval) in blue.

SELF ADJUST

On a D-SUB[RGB] screen, specify whether to perform screen adjustment automatically or not.

When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input

signals changes. “ADJUSTING” appears on the screen during the adjustment. If SELF ADJUST is set to ON, set the time it takes to start the SELF ADJUST function in START TIMING. For images with black edges, etc., depending on the signal, adjustment may not be possible. In this case select OFF. (Perform manual adjustment of the screen.)

TOUCH PANEL

TOUCH OUTPUT INVALID DISP.

TOUCH OUTPUT INVALID ICON ......

CHANGE DISPLAY POSITION .......... Sets the display position of the TOUCH OUTPUT INVALID icon.

TOUCH OPERATION MODE

Select the touch mode.

The touch panel must be connected in order to congure this setting.

You can select AUTO to automatically set SINGLE-TOUCH MODE / MULTI-TOUCH MODE as required for your operating system.

PALM CANCEL MODE

When you write with the touch pen, you can set the touch panel to not respond when your hand touches the screen.

TOUCH PANEL MODE (HDMI/D-SUB[RGB]/DisplayPort/OPTION)

When the vertical frequency of the input signal is 60 Hz, setting this to ON improves touch panel tracking. When two screens are displayed, or when V-POS or V-SIZE is adjusted on the SCREEN menu, the screen may become distorted. Some input signals may also cause screen distortion. If the screen becomes distorted, set to OFF.

Sets whether the TOUCH OUTPUT INVALID icon is displayed when touch action is disabled.

Page 37

Menu Items

MULTI/PIP

PIP/PbyP

PIP MODES

Sets the display method.

OFF ........... Displays one screen.

PIP ............ Displays a sub screen inside a main screen.

PbyP .......... Displays a main screen and a sub screen in a line.

PbyP2........ Displays a main screen which measures 2560 pixels in the longest direction and a sub screen in a line.

PIP SIZE

Sets the size of the sub screen in PIP mode.

PIP H-POS

Adjusts the horizontal position of the sub screen in PIP mode.

PIP V-POS

Adjusts the vertical position of the sub screen in PIP mode.

PIP BLEND

In PIP mode, use this menu item to display the sub screen transparently.

PIP SOURCE

Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.

SOUND CHANGE

Sets the sound which is output in PIP, PbyP, or PbyP2 mode.

MAIN POS

Sets the position of the main screen in PbyP or PbyP2 mode.

PbyP2 POS

Sets the position of the sub screen in PbyP2 mode.

CONFIGURE QUAD-SCREEN

QUAD-SCREEN MODE

Set how the screens are displayed.

OFF ........... Display single screen.

ON ............. Display 4 screens simultaneously.

SETTING INITIAL SCREEN

Set the input mode displayed in each of the 4 screens. When AUTO is selected, input modes that have input signals are displayed in the order set in PRIORITY: AUTO INPUT SEL..

PRIORITY: AUTO INPUT SEL.

Set the order of priority for the input mode that is displayed when AUTO is selected for SETTING INITIAL SCREEN.

SAVE LAST INPUT CONFIG.

OFF ........... When quad-screen display is started, the four screens set in SETTING INITIAL SCREEN always appear.

ON ............. When quad-screen display is started, the previously displayed four screens appear.

TARGET: SOUND / INPUT SEL.

When quad-screen is displayed, you set the screen whose audio is output, and the screen whose input is changed. When you return to single screen display, the input mode will return to the input mode set here.

RECONFIGURE QUAD-SCREEN

Displays 4 screens again according to SETTING INITIAL SCREEN setting. This can be set when QUAD-SCREEN MODE is set to ON.

INPUT SIGNAL INFO.

This shows the input mode, resolution, and frequency of the displayed screens.

Page 38

Menu Items

OTHERS

POWER MANAGEMENT

POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal waiting mode.

CONNECT AUTO INPUT SELECT

Sets whether the input into the input terminal automatically changes when a video signal is input into that terminal. (With some input signals, the input may not change.)

NO SIGNAL AUTO INPUT SEL.

Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, the monitor automatically changes the selected mode to another mode where a video signal is present. When there are video signals in multiple input modes, switching takes place according to the order of priority set in AUTO

INPUT SELECT PRIORITY.

AUTO INPUT SELECT PRIORITY

Sets the order of input terminal priority for NO SIGNAL AUTO INPUT SEL.. When an option that supports this function is connected to the expansion slot, you can set the order in OPTION. (If the option does not support this function, OPTION will not appear.) Input does not change automatically for terminals without a priority setting.

LOGO SCREEN

Sets whether or not to display the logo screen.

SCAN MODE (HDMI/D-SUB[COMPONENT]/OPTION)

Sets the scan mode used for video input.

MODE1 ............... Over-scan display.

MODE2 ............... Under-scan display.

Even when MODE1 is selected, under-scan display is used when the input signal is 3840×2160 and the screen size is Dot by Dot.

VOLUME

Adjusts the volume.

MUTE AUDIO

Can temporarily turn off the volume.

MUTE WITH FREEZE

Set whether or not audio turns off during freeze.

TIPS

• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, GAMMA and COPY TO USER cannot be set.

• If COLOR MODE is set to sRGB, the following items cannot be set. PRESET, USER, COPY TO USER, and GAMMA

• When the COLOR MODE is set to VIVID or HIGH ILLUMINANCE, GAMMA can not be adjusted.

• When displaying the color pattern, it is possible to adjust certain items of the PICTURE menu. Non-adjustable items cannot be selected.

• CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. do not work for the Sync-on-green signal of

D-SUB[RGB] or the signals of D-SUB[COMPONENT].

Page 39

Menu Items

Landscape orientation Portrait orientation

Dual screen display

You can display two screens simultaneously. Set this function with “PIP MODES” in the MULTI/PIP menu.

PIP

PbyP

PbyP2

Main screen

Main

screen

Main screen

Sub

screen

Sub

screen

A sub screen is displayed

inside a main screen.

A main screen and a sub

screen are displayed in a

line.

Displays a main screen which measures 2560

Sub

pixels in the longest direction and a sub screen in a line.

* The currently selected input signal is displayed on the main

screen.

* The following combinations are available for display:

DisplayPort1 - DisplayPort2 DisplayPort1 - HDMI1, HDMI2, HDMI3 DisplayPort1 - D-SUB[RGB] DisplayPort1 - D-SUB[COMPONENT] DisplayPort1 - OPTION DisplayPort2 - HDMI1, HDMI2, HDMI3 DisplayPort2 - D-SUB[RGB] DisplayPort2 - D-SUB[COMPONENT] DisplayPort2 - OPTION HDMI1 - HDMI2, HDMI3

HDMI2 - HDMI3

HDMI1, HDMI2, HDMI3 - D-SUB[RGB] HDMI1, HDMI2, HDMI3 - D-SUB[COMPONENT] HDMI1, HDMI2 - OPTION

D-SUB[RGB], D-SUB[COMPONENT] - OPTION

TIPS

• You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for prot-making or to show the image to the public.

• The screen size for dual-screen display is the same as the screen size for single-screen display. The Dot by Dot screen is displayed in NORMAL size except when it is set

as the PIP main screen.

• When dual-screen display is selected, the CONNECT

AUTO INPUT SELECT function and NO SIGNAL AUTO INPUT SEL. function are disabled.

• When dual-screen display is selected, the INPUT SELECT

options cannot be set.

• When dual-screen display is selected, the AUDIO menu

cannot be set.

• When an interlaced signal (1080i, 480i, video) is input to the sub screen, horizontal lines may icker. If this happens, display the image on the main screen.

• Touch operation cannot be used in the sub screen.

• When DisplayPort STREAM is set to MST, you cannot set PIP MODES to PIP, PbyP, or PbyP2.

• When HDMI CEC LINK is set to AUTO, SOUND CHANGE

on the PIP/PbyP may be changed to MAIN due to the switching of the monitor’s input or due to the operation of

the HDMI-connected device.

Quad screen display

You can display four screens simultaneously.

Position 1

(1920×1080)

Position 3

(1920×1080)

Position 2

(1920×1080)

Position 4

(1920×1080)

Position 1

(1920×1080)

Position 3

(1920×1080)

Position 2

(1920×1080)

Position 4

(1920×1080)

Displaying 4 screens

1. Touch the TOUCH MENU button, and touch the QUAD-

SCREEN ON icon (

Or, set CONFIGURE QUAD-SCREEN – QUAD-SCREEN

MODE to ON in the MULTI/PIP menu.

• The four screens set in SETTING INITIAL SCREEN appear.

• When SAVE LAST INPUT CONFIG. is ON, the

previously displayed four screens appear.

• You can return the quad-screen display to the four

screens set in SETTING INITIAL SCREEN using RECONFIGURE QUAD-SCREEN in the touch menu, or CONFIGURE QUAD-SCREEN – RECONFIGURE

QUAD-SCREEN in the MULTI/PIP menu.

Deciding the screen that will be the audio output/input mode selection target

Set the screen whose audio is output, and the screen whose

input is changed.

1. Press and hold the screen you want to be the target.

Or, set in CONFIGURE QUAD-SCREEN – TARGET:

SOUND / INPUT SEL. in the MULTI/PIP menu.

Returning to single screen

1. Touch the TOUCH MENU button, and touch the QUAD-

SCREEN OFF icon (

Or, set CONFIGURE QUAD-SCREEN – QUAD-SCREEN

MODE to OFF in the MULTI/PIP menu.

• The screen set in TARGET: SOUND / INPUT SEL. is displayed on screen 1.

Page 40

Menu Items

––

TIPS

• When quad-screen display is selected, screen size cannot

be changed.

The screen size for quad-screen display is the same as the screen size for single-screen display. The Dot by Dot screen is displayed in NORMAL size except when it is set

as the PIP main screen.

• When quad-screen display is selected, the CONNECT

AUTO INPUT SELECT function and NO SIGNAL AUTO INPUT SEL. function are disabled.

• When quad-screen display is selected, D-SUB of INPUT

SELECT cannot be set.

• When quad-screen display is selected, SCREEN and

AUDIO cannot be set.

• When the screen size is set to ZOOM2 and ZOOM2 SPECIAL SETTING is set to ON, that display state is held.

• When quad-screen display is selected, DisplayPort2 of DisplayPort STREAM cannot be set.

• When quad-screen display is selected, the monitor will not enter the input signal waiting mode when POWER

MANAGEMENT is set to ON.

• When quad-screen display is selected, the HDMI CEC

LINK function cannot be set.

• When quad-screen display is selected, the FREEZE, DP (DisplayPort), HDMI, and OPTION buttons cannot be used.

• When quad-screen display is selected, the position 1 screen is output from the DisplayPort output terminal.

• When quad-screen display is selected, the connected computer cannot be operated by touch.

ZOOM2 SPECIAL SETTING

If you connect a laptop computer with any of the following screen resolutions and black bands appear around the screen,

set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the OTHERS menu to ON and then select ZOOM2 in the SIZE setting.

This displays the area inside the black band.

Laptop computer

Corresponding signal*

resolution

1280x800 1280x1024, 1280x960, 1400x1050*

1280x600 1280x720

1024x600 1024x768

*1: This setting is effective only when the screen resolution,

including the black band, is one of the resolutions listed

above.

*2: Use the automatic screen adjustment.

SCHEDULE

You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the SETUP menu. (See

page 34.)

– – – – – – – – – – – – – – – –

D-SUB[RGB]

(5)(2) (3) (4) (6)

–– –––

SCHEDULE

(1)

No.

– –/– –/– – – – – – –

POWER DAY OF THE WEEK

– –– –– –– –– –– ––

– – –– –– –– –– –– ––– – –– –– –– –– –– ––– – –– –– –– –– –– ––– – –– –– –– –– –– ––– – –– –– –– –– –– ––– – –– –– –– –– –– ––– – –– –– –– –

– –:– –:– – – –

TIME INPUT BRIGHT

– –

–

OK:[ENTER] CANCEL:[RETURN]

1. Press the or button to select the SCHEDULE

number, and press the

button.

2. Set the SCHEDULE. (See the description below.)

Press the

or button to select items, and press the or

button to change the setting.

3. Press the ENTER button.

SCHEDULE becomes effective.

(1)

●: SCHEDULE effective

: SCHEDULE not effective

(2) POWER

ON : Switches the monitor on at the specied time. OFF : Switches the monitor off at the specied time and puts

the monitor in standby mode.

(3) DAY OF THE WEEK

Species the day of the week to execute the SCHEDULE. 0:ONLY ONCE

Executes the SCHEDULE once on the specied day. Specify the day of the week to execute the SCHEDULE.

1:EVERY WEEK

Executes the SCHEDULE on the specied day of the week every week. Specify the day of the week to execute the

SCHEDULE.

Periodic setting such as “Monday through Friday” is also

possible.

2:EVERY DAY

Executes the SCHEDULE every day regardless of the day of the week.

(4) TIME

Species the time to execute the SCHEDULE. Set the time on a 12-hour basis. (Factory default)

Can be entered as 24-hour time using the TIME setting in

DATE/TIME FORMAT.

(5) INPUT

Species the input mode at power-on. If not specied, the START INPUT MODE setting will apply. By factory default, the input that was active when the power was last turned off will appear. Input modes displayed on D-SUB will depend upon the

INPUT SELECT settings.

Page 41

Menu Items

(6) BRIGHT

Sets the brightness when changing the screen brightness at a specied time.

Caution

• Do not switch off the main power after setting the

SCHEDULE.

• Specify the correct date and time. (See page 34.)

SCHEDULE does not function unless the date and time are

specied.

• Check regularly that the set date and time are correct.

• When a temperature abnormality occurs and the backlight

brightness is reduced, the brightness is not changed even if a schedule set to BRIGHT is executed.

TIPS

• Up to 8 SCHEDULE items can be registered.

• A SCHEDULE that has a large number has precedence

over that of a small number when schedules overlap.

About remote control numbers

If there is another monitor nearby, you can change the remote

control number to prevent the other monitor from being

operated by the remote control unit.

Set the same number in the monitor and in the remote control unit.

TIPS

• You can set remote control numbers to values from 0 to 9.

• When the remote control unit batteries become exhausted

and when you replace the batteries, the number on the remote control unit may be reset to 0.

Changing the remote control number on the monitor

Use REMOTE No. on the SETUP menu to set the number.

(See page 35.)

1. Use the number.

2. Select ON and press the ENTER button.

The remote control number is set on the monitor.

Changing the remote control number on the remote control unit

1. While holding down the ID SET button, hold down the

number that corresponds to the remote control number

set on the monitor for 5 seconds or more, and then

release these buttons.

The remote control number is set on the remote control unit.

or button to select the remote control

Checking the remote controller number

* Perform these steps on the remote control unit.

Press the INFORMATION button to display INFORMATION1.

2. Check that REMOTE No. is the remote control number that you have set in the above procedure.

3. Press the RETURN button to close the monitor INFORMATION screen.

TIPS

• If the remote control numbers on the monitor and remote

control unit are different, they will both be displayed on INFORMATION1. On this screen, you can press the ENTER button to match the number on the monitor with the

number on the remote control unit.

• Even if the remote control numbers are different, you can use the remote control unit to display the INFORMATION

screen.

Page 42

Menu Items

Adjustments for computer screen display

Automatic adjustment

When you use D-SUB[RGB] to display a computer screen for the rst time, or when you change the setting of the computer, use the automatic screen adjustment.

1. Switch the input to D-SUB[RGB] and display the

adjustment pattern. (See the description below.)

2. Press the MENU button and use the

display the SCREEN menu.

3. Press the ENTER button and select “AUTO”.

4. Press the ENTER button.

The automatic adjustment is complete in several seconds.

5. Press the MENU button to close the menu screen.

TIPS

• If the screen cannot be adjusted properly with one automatic adjustment, repeat the automatic adjustment two or three times. Try manual adjustment if necessary.

or button to

Screen display for adjustment

Before making adjustments in the SCREEN menu or PICTURE menu, display an image to brighten the entire screen. If you are using a Windows computer, use the adjustment pattern on the supplied CD-ROM.

Opening the adjustment pattern

The following example is performed in Windows 7.

1. Load the supplied CD-ROM into the computer’s CDROM drive.

2. Open [CD Drive] in [Computer].

3. Double-click [Adj_uty.exe] in the [Monitor] folder.

The adjustment pattern will appear. Adjust the screen automatically or manually.

4. When adjustment is nished, press the [Esc] on the

computer’s keyboard to quit the adjustment program.

5. Eject the CD-ROM from the CD-ROM drive.

TIPS

• If the display mode on the computer you are using is 65000 colors, the color levels in the color pattern may appear differently or grayscale may appear to be colored. (This is due to the specications of the input signal and is not a

malfunction.)

Page 43

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

You can return the settings to their factory-preset values and

restrict operations.

1. Press the FUNCTION button, and then press the MENU

button within 10 seconds.

FUNCTION

▲

ALL RESET

ADJUSTMENT LOCK

ADJUSTMENT LOCK TARGET

RS-232C/LAN OSD DISPLAY LED TEMPERATURE ALERT

STATUS ALERT POWER BUTTON

EXTERNAL CONTROLLER INPUT

SIGNAL RESPONSE LEVEL

OFF

▲▲▲▲▲▲▲▲

UNLOCKED

ON 1

ON LED OFF

MONITOR

OK:[ENTER] END:[RETURN]

▲ ▲▲▲▲▲▲▲

2. Select and set the items.

ALL RESET

Resets the settings to the factory default settings. Press the ENTER button, select the resetting method, and then press the ENTER button.

ALL RESET1 ....Resets all the settings to the factory

default settings.

ALL RESET2 ....Returns all settings to the factory default

settings except for the following items: LAN SETUP, RS-232C/LAN SELECT,

REMOTE No., BAUD RATE, NETWORK, MAIL, SERVICE &

SUPPORT, and SNMP. (See page 35, and pages 58 to 61.)

ADJUSTMENT LOCK

You can disable operations on the monitor and the remote control unit that use buttons.

OFF ....Enables operation.

ON 1 ... Disables all operations other than turning power

on/off and FUNCTION.

ON 2 ... Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION

(not even power on/off).

ADJUSTMENT LOCK TARGET

Sets the target to prohibit operation of with ADJUSTMENT LOCK.

REMOTE CONTROL ..... Prohibits remote control

operation

MONITOR BUTTONS ... Prohibits monitor button

operation

BOTH ............................. Prohibits remote control and

monitor button operation

RS-232C/LAN

Species whether to allow control via RS-232C or LAN. (See pages 44 and 54.)

OSD DISPLAY

Shows/hides the menu, modes and messages.

The FUNCTION screen cannot be hidden.

ON 1 .............. Shows all menus, modes and messages.

ON 2 .............. Hides messages automatically displayed

by the display. Shows messages during

operation.

OFF ............... Hides all menus, modes and messages.

LED

Species whether to light the power LED.

TEMPERATURE ALERT

Selects the notication method for an abnormal

temperature.

OFF ............... Do not notify about an abnormal

temperature.

OSD & LED ... When an abnormal temperature is

detected, the power LED ashes in orange and blue alternately and the screen displays a message:

TEMPERATURE.

LED................ When an abnormal temperature is

detected, the power LED ashes in orange and blue alternately.

STATUS ALERT

Selects the notication method for a hardware error.

OFF ............... Do not notify about the error.

OSD & LED ... When a hardware error is detected, the

power LED illuminates in blue and orange alternately and the screen displays a

message: STATUS [xxxx].

LED................ When a hardware error is detected, the

power LED illuminates in blue and orange alternately.

POWER BUTTON

Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears,

change the setting accordingly.

EXTERNAL CONTROLLER INPUT

Normally, you do not need to change this setting.

When using an optional part, if instruction appears,

change the setting accordingly.

SIGNAL RESPONSE LEVEL

Normally, you do not need to change this setting. Use

this option to set the level of response to signal changes.

3. Press the RETURN button to return to the normal screen.

TIPS

• When both abnormal temperature and hardware error are detected, the hardware error notication overrides.

• If TEMPERATURE ALERT or STATUS ALERT is set to

OSD&LED, alert messages will appear even if the OSD

DISPLAY is set to ON 2 or OFF.

• If TEMPERATURE ALERT or STATUS ALERT is set to LED or OSD & LED, the LED lights even if the LED function is set to OFF.

Page 44

Controlling the Monitor with a computer (RS-232C)

RS-232C conversion cable (supplied)

(commercially available)

Return code

alphanumerical characters

)

(4 character string comprised of:

You can control this monitor from a computer via RS-232C (COM port) on the computer.

TIPS

• To control the monitor via RS-232C, set RS-232C/LAN

SELECT to RS-232C.

• You cannot use RS-232C and LAN control simultaneously.

Computer connection

Connect the RS-232C conversion cable (supplied) to the RS232C input terminal on the monitor. Connect the RS-232C conversion cable (supplied) to the COM port (RS-232C port)

on your computer with an RS-232 cable (straight).

RS-232C input terminal

Computer

To COM port

Communication conditions

Set the RS-232C communication settings on the computer to

match the monitor’s communication settings as follows:

Baud rate *

Data length 8 bits Flow control None

Parity bit None

* Set to the same baud rate as the BAUD RATE setting of

SETUP menu. (Initial setting: 38400 bps)

Stop bit

1 bit

Communication procedure

Command format

When a command is sent from the computer to the monitor, the monitor operates according to the received command and sends a response message to the computer.

C1 C2 C3 C4 P1 P2 P3 P4

Command field

(4 prescribed

Parameter field

0-9, +, -, space, ?)

RS-232 straight cable

Example: VOLM0030

VOLM

* Be sure to input 4 characters for the parameter. Pad with

spaces (“ (“

Wrong : VOLM30 Right : VOLM 30

When inputting a negative value, specify a numerical value in

three digits.

Example: AUTR-005

When the parameter part is 5 or more characters, specify parameters using a specied number of characters without

using spaces.

Example: MPOS010097

If a command has “R” listed for “Direction” in the “RS-232C command table” on page 47, the current value can

be returned by using “?” as the parameter.

Example:

VOLM ? ? ? ? ←

30 ←

”) if necessary.

” is a return code (0DH, 0AH or 0DH))

From computer to monitor

(How much is current volume setting?).

From monitor to computer

(Current volume setting: 30).

Page 45

Controlling the Monitor with a computer (RS-232C)

Return code

VOLM0020 OK

INPS0001 WAIT OK

Interval of 100 ms or more

Response code format

When a command has been executed correctly

O K

(0DH, 0AH)

A response is returned after a command is executed.

When a command has not been executed

R R E

(0DH, 0AH)

TIPS

• “ERR” is returned when there is no relevant command or when the command cannot be used in the current state of

the monitor.

• If communication has not been established for reasons

such as a bad connection between the computer and

monitor, nothing is returned (not even ERR).

• “ERR” may be returned when a command cannot be received correctly due to interference from the surrounding

environment.

Please ensure that the system or software retries the

command if this occurs.

Communication interval

• After OK or ERR is returned, you must send the following

commands.

To set a timeout for the command response, specify 10

seconds or longer.

• Provide an interval of 100 ms or more between the

command response and the transmission of the next command.

TIPS

• When executing ALL RESET, set the timeout period to 30

seconds or longer.

• When turning the power on while the POWER ON DELAY

function is in use, set the timeout period to the POWER ON

DELAY period + 10 seconds or longer.

If execution of the command is taking some time

I W T A

(0DH, 0AH)

When the following commands are used, “WAIT” is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period.

• Commands which return WAIT:

RSET, INPS, ASNC, WIDE, PXSL, POWR, AGIN, MWIN,

MWIP, MWPP, DPST, DPS2, MSCS, MSP1, MSP2, MSP3,

MSP4

When control via RS-232C is locked (see page 43)

E C D K O L

(0DH, 0AH)

When RS-232C/LAN SELECT is set to LAN

U N S E L E C T E D

(0DH, 0AH)

Page 46

Controlling the Monitor with a computer (RS-232C)

…

Command field

Block number (01 to 16)

Data fieldChecksum field

UGRW01000000010002 … 0031C0

Command

Block number

32 pieces of data Checksum

Setting of the GAMMA user data

To transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and UGBW). For each of the R, G and B colors, divide the total

512 pieces of user data into 16 blocks, and transfer 32 pieces of data with each command.

C1 C2 C3 C4 P1 P2 P3 P4

Example: To transfer the data of block 1 (0 to 31 levels)

of red (R) data

One piece of data consists

of 4 digits.

* If data is less than 4 digits, add a “0” (zero) to make it 4

digits.

* The checksum eld is the character string (ASCII) data of

lower-order one byte which indicates the sum of the block number and 32 pieces of data in hexadecimal (0 to F).

Saving the GAMMA user data

Use the user data save command (UGSV) to save the transferred user data in the monitor.

If the data is not saved, it will be cleared when:

• The main power switch is off.

• POWER SAVE MODE is ON and the monitor enters

standby mode.

S1 S2

Activating the GAMMA user data

To activate the transferred user data, select USER for GAMMA of the PICTURE menu, or send the corresponding RS-232C command.

Checking the GAMMA user data

Use the user data read commands (UGRR, UGGR and

UGBR) to return 512 pieces of user data for each of the R, G and B colors. Divide the data into 16 blocks and return 32 pieces of data with each command. The value to be returned

is not the value stored in the monitor, but the value in the

temporary memory for display. (These values are the same when the user data save command (UGSV) above has been

sent.)

TIPS

• The user data is not initialized by RESET of the PICTURE menu. To initialize the user data, use ALL RESET of the

FUNCTION menu.

The GAMMA user data initialize command (UGRS) allows the initialization of the user data only.

Page 47

Controlling the Monitor with a computer (RS-232C)

RS-232C command table

How to read the command table

Command: Command eld (See page 44.) Direction: W When the “Parameter” is set in the parameter eld (see page 44), the command functions as described

R The returned value indicated under “Reply” can be obtained by setting “????” or “

Parameter: Parameter eld (See page 44.) Reply: Response (Returned value)

* : When POWER SAVE MODE is set to OFF:

“●/○” : Indicates a command which can be used in standby mode or when the power is on. “–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.

When POWER SAVE MODE is set to ON:

“●” : Indicates a command which can be used in standby mode or when the power is on. “○/–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.

Power control/Input mode selection

Function

POWER CONTROL POWR W 0

INPUT MODE SELECTION INPS W 0 Toggle change for input mode. Terminals not selected in INPUT SELECT cannot

under “Control/Response Contents”.

parameter eld (see page 44).

Command Direction

R 0 Standby mode

R 2 D-SUB[RGB]

Parameter Reply Control/Response contents *

1 Returns from standby mode.

2 D-SUB[RGB]

3 D-SUB[COMPONENT]

10 HDMI1 13 HDMI2 14 DisplayPort 1 18 HDMI3 21 OPTION

22 DisplayPort 2

?” in the

Switches to standby mode.

1 Normal mode

2 Input signal waiting mode

be selected.

“ERR” when other than RGB is selected for D-SUB of INPUT SELECT.

“ERR” when other than COMPONENT is selected for D-SUB of INPUT SELECT.

“ERR” when nothing is attached in the expansion slot.

3 D-SUB[COMPONENT]

10 HDMI1 13 HDMI2 14 DisplayPort 1 18 HDMI3 21 OPTION 22 DisplayPort 2

●

Page 48

Controlling the Monitor with a computer (RS-232C)

SCREEN menu

AUTO ASNC W 1 When the input mode is D-SUB[RGB]. CLOCK CLCK WR 0-1200 0-1200 When the input mode is D-SUB[RGB].

PHASE PHSE WR 0-63 0-63 When the input mode is D-SUB[RGB]. POSITIONING POSITION OF

SIZE SIZE OF THE

RESOLUTION SETTING

INPUT SIGNAL (D-SUB[RGB]) PXSL WR 1 1 768) 1360 x 768

Check the resolution

(other than D-SUB[COMPONENT])

Check the resolution

(HDMI, D-SUB[COMPONENT], OPTION

(When you have used the expansion

slot to expand the functions.)) ZOOM2 SPECIAL SETTING

(D-SUB[RGB]) RESET ARST W 1 -

Function

THE LONGEST DIRECTION

POSITION OF THE SHORTEST DIRECTION

LONGEST DIRECTION

SIZE OF THE SHORTEST DIRECTION

LONGEST DIRECTION RESOLUTION

SHORTEST DIRECTION RESOLUTION

Command Direction

HPOS WR 0-100 0-100 0-800 on D-SUB[RGB].

VPOS WR 0-200 0-200 0-200 on D-SUB[RGB].

HSIZ WR 0-100 0-100

VSIZ WR 0-100 0-100

HRES WR 300-1920 300-1920 When the input mode is D-SUB[RGB].

VRES WR 300-1200 300-1200

PXCK R - Returns current resolution in the form of hhh, vvv.

RESO R - 480i, 480p, 1080i, 720p, 1080p , etc.

Z2SP WR 0-1 0-1 0: OFF, 1: ON

Parameter Reply Control/Response contents *

Varies depending on the signal.

Only even numbers are valid for parameters.

Varies depending on the signal.

2 2 768) 1280 x 768 3 3 768) 1024 x 768

5 5 480) 848 x 480

6 6 480) 640 x 480 7 7 1050) 1680 x 1050 8 8 1050) 1400 x 1050 9 9 768) AUTO

10 10 480) AUTO

○

Page 49

Controlling the Monitor with a computer (RS-232C)

PICTURE menu

Function

BRIGHT VLMP WR 0-31 0-31 CONTRAST CONT WR 0-60 0-60 BLACK LEVEL BLVL WR 0-60 0-60 TINT TINT WR 0-60 0-60 COLORS COLR WR 0-60 0-60 SHARPNESS SHRP WR 0-24 0-24

COLOR

ADJUSTMENT

ADVANCED AUTO

RESET ARST W 2

COLOR MODE BMOD WR 0 0 STD

WHITE BALANCE WHBL WR 0-2 0-2 0:THRU, 1:PRESET, 2:USER PRESET CTMP WR 1-28 1-28

USER R-CONTRAST CRTR WR 0-256 0-256 “ERR” when WHBL is not set to 2.

G-CONTRAST CRTG WR 0-256 0-256 B-CONTRAST CRTB WR 0-256 0-256 R-OFFSET OFSR WR -127-127 -127-127 G-OFFSET OFSG WR -127-127 -127-127

COPY TO USER CPTU W 0 Copies a preset value to the user setting. GAMMA GAMM WR 0-2, 4-9 0-2, 4-9 0: 1.8, 1: 2.2, 2: 2.4, 4:USER, 5:2.0, 6:STD, 7:LIGHT 2, 8:LIGHT 1, 9:DARK FLESH TONE FLES WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH C.M.S.-HUE

C.M.S.-SATURATION

ANALOG GAIN

ANALOG OFFSET

NR RGB INPUT RANGE INPR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

DISPLAY COLOR PATTERN PTDF WR

DISPLAY COLOR PATTERN (R)

DISPLAY COLOR PATTERN (G)

DISPLAY COLOR PATTERN (B)

DISPLAY COLOR PATTERN (LEVEL)

B-OFFSET OFSB WR -127-127 -127-127

Command Direction

CMHR WR -10-10 -10-10 R

CMHY Y

CMHG G

CMHC C

CMHB B

CMHM M CRST W 1 Resets the hue. CMSR WR -10-10 -10-10 R

CMSY Y

CMSG G

CMSC C

CMSB B

CMSM M

CRST W 2 Resets the saturation. AGIN W 1 When the input mode is D-SUB[RGB]. ANGA WR 0-127 0-127 When the input mode is D-SUB[RGB]. ANOF WR 0-127 0-127 When the input mode is D-SUB[RGB]. TDNR WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH

PTDR WR 0-255 0-255 Set the R, G, and B levels of the mixed color pattern.

PTDG WR 0-255 0-255

PTDB WR 0-255 0-255

PTDL WR 0-255 0-255 Set the white, red, green, and blue levels of the single color pattern.

Parameter Reply Control/Response contents *

2 2 VIVID 3 3 sRGB (sRGB cannot be used when input mode is D-SUB[COMPONENT].)

4 4 HIGH ILLUMINANCE

0 0 No pattern display. 1 1 White single color pattern display.

2 2 Red single color pattern display. 3 3 Green single color pattern display. 4 4 Blue single color pattern display.

99 99 Red/green/blue mixed color pattern display.

From 1: approximately 3,000K to 15: approximately 10,000K (500K steps) 16: approximately 5,600K, 17: approximately 9,300K, 18: approximately 3,200K From 19: approximately 10,500K to 28: approximately 15,000K (500K steps) "ERR" when WHBL is not set to 1.

“ERR” when the input mode is D-SUB[COMPONENT]. When the input mode is D-SUB[RGB] the value 0 is invalid.

Set each color's level with PTDR, PTDG, PTDB.

“ERR” when PTDF is not set to 99.

“ERR” when the DISPLAY COLOR PATTERN is set to a color other than white,

red, green, or blue.

○

Page 50

Controlling the Monitor with a computer (RS-232C)

AUDIO menu

Function

TREBLE AUTR WR -5-5 -5-5

BASS AUBS WR -5-5 -5-5

BALANCE AUBL WR -10-10 -10-10

RESET ARST W 3 -

Command Direction

Parameter Reply Control/Response contents *

SETUP menu

Function

DATE/TIME SETTING DATE WR DATE DISPLAY FORMAT DTFT WR

TIME DISPLAY FORMAT TMFT WR SCHEDULE SC01-

SCHEDULE BRIGHTNESS SB01-

LANGUAGE LANG WR 14 14 ENGLISH

INPUT SELECT D-SUB SLDS WR 0-1 0-1 0:RGB, 1:COMPONENT

INPUT MODE NAME

Edit the input mode name

AUDIO SELECT

HDMI CEC LINK AUTO POWER ON HDMI AUTO VIEW

(HDMI1)

HDMI AUTO VIEW (HDMI2)

HDMI AUTO VIEW (HDMI3)

HDMI AUTO VIEW (

OPTION

)

DisplayPort STREAM (DisplayPort1)

DisplayPort STREAM (DisplayPort2)

HDMI MODE

DisplayPort 1 DisplayPort 2 HDMI1 INH1

HDMI2 INH2 HDMI3 INH3 D-SUB IND1 INPUT1 IN1E WR xxxxxxxxx INPUT2 IN2E INPUT3 IN3E INPUT4 IN4E

INPUT5 IN5E

INPUT6 IN6E

DisplayPort 1 DisplayPort 2 HDMI1

HDMI2 HDMI3 OPTION

(valid when you have

used the expansion slot to expand the functions)

(HDMI1)

(HDMI2) (HDMI3)

Command Direction

SC08

SB08

CELK WR 0-1 0-1 0: OFF, 1: AUTO ATPO WR 0-1 0-1 0: OFF, 1: ON HDAW WR 0-1 0-1 0: OFF, 1: ON

H2AW WR 0-1 0-1 0: OFF, 1: ON

H3AW WR 0-1 0-1 0: OFF, 1: ON

OPAW WR 0-1 0-1 0: OFF, 1: ON

DPST WR 0, 2 0, 2 0: SST1, 2: SST2

DPS2 WR 0-2 0-2 0: SST1, 1: MST, 2: SST2

HD1M WR 0-1 0-1 0: MODE1, 1: MODE2 HD2M WR 0-1 0-1 0: MODE1, 1: MODE2 HD3M WR 0-1 0-1 0: MODE1, 1: MODE2 INDP WR 0-30 0-30 0: NO SETTING, 1: PC1, 2:PC2, 3: PC3, 4: TV, 5: VIDEO, 6: DVD, 7: HDD, INP2

ASDI WR 1, 3 1, 3 ASD2 WR 1, 3 1, 3 ASHP WR 0-1 0-1 AH2P WR 0-1 0-1 AH3P WR 0-1 0-1 ASOP WR 0-2 0-2

WR ABCDEFFGGH ABCDEFFGGH Schedule of a specied number

WR 0-31 0-31 Screen brightness to change

Parameter Reply Control/Response contents *

YYMMDDOOMM YYMMDDOOMM

0-2 0-2

0-1 0-1

99 99 Disable brightness setting

1 1 DEUTSCH 2 2 FRANÇAIS 3 3 ITALIANO 4 4 ESPAÑOL

5 5 РУССКИЙ

6 6

xxxxxxxxx

xxxxxxxxx xxxxxxxxx

YY: Year, MM: Month, DD: Day, OO: Hour, MM: Minute 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY

YYYY: Year, MM: Month, DD: Day 0: 24-HOUR TIME, 1: 12-HOUR TIME

A: Schedule 0= Not effective, 1 = Effective B: Power 0 = OFF, 1 = ON C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday, 9 = Not exist E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday, 9 = Not exist F: Hour 00-23 G: Minute 00-59 H: Input 0 = Not specied, 1 = HDMI1, 2 = HDMI2, 3 = HDMI3,

(valid when you have used the expansion slot to expand the functions)

8: DVR, 9: BD, 10: CAMERA, 11: DOCUMENT CAMERA, 12: VIDEO CAMERA, 13: VIDEO CONFERENCE, 14: WIRELESS, 15: STB, 16: CONTROLLER, 17: COMPOSITE, 18: COMPONENT, 19: RGB, 20: INPUT1, 21: INPUT2, 22: INPUT3, 23: INPUT4, 24: INPUT5, 25: INPUT6, 26: SATELLITE, 27: CABLE, 28: CAMCORDER, 29: TABLET, 30: SURVEILLANCE CAM.

Input mode name (Half-width alphanumeric characters and symbols only, maximum of 18 characters)

1: AUDIO, 3: DisplayPort 1: AUDIO, 3: DisplayPort 0: HDMI, 1: AUDIO 0: HDMI, 1: AUDIO 0: HDMI, 1: AUDIO 0: OPTION, 1: AUDIO

4 = D-SUB, 6 = DisplayPort1, 7=DisplayPort2, 8=OPTION (valid when you have used the expansion

slot to expand the functions)

○

-HDMI MODE

○

Page 51

Controlling the Monitor with a computer (RS-232C)

AUDIO OPTION

TOUCH INPUT SELECT

START INPUT MODE SUIM

COMMUNICATION SETTING

REMOTE No. RCNO WR 0-9 0-9 Sets the number of the remote control unit.

Function

SPEAKER SELECT AUDIO OUTPUT AUDIO INPUT LEVEL MONAURAL AUDIO BOTTOM USB

(Long side) SIDE USB (Short side) USCS WR

RS-232C/LAN

SELECT BAUD RATE BAUD WR Crestron Connected CRCN WR

Command Direction

SPSL WR 0-1 0-1 AOUT WR 0-2 0-2 AIVP WR 0-1 0-1 MONO WR 0-1 0-1 USCB WR

WR 1-5, 7, 10-11 1-5, 7, 10-11

CTLS WR

Parameter Reply Control/Response contents *

0-6, 8 0-6, 8

0-1 0-1

0-2 0-2 0-1 0-1

0: Internal speaker, 1: External speaker 0: VARIABLE1, 1: FIXED, 2: VARIABLE2 0: 1.0Vrms, 1: 0.5Vrms 0: OFF, 1: ON 0: INVALID, 1: BOTTOM INPUT TERM. (Long side), 2: DisplayPort1, 3: HDMI1,

4: HDMI2, 5: HDMI3, 6: D-SUB, 8:DisplayPort 2 0: INVALID, 1: SIDE INPUT TERM. (Short side), 2: DisplayPort1, 3: HDMI1,

4: HDMI2, 5: HDMI3, 6: D-SUB, 8:DisplayPort 2 1: LAST INPUT MODE, 2: DisplayPort 1, 3: HDMI1, 4: HDMI2, 5: HDMI3,

7: D-SUB, 10:OPTION (valid when you have used the expansion slot to expand the functions), 11:DisplayPort 2

0: RS-232C, 1: LAN

0: 9600bps, 1: 19200bps, 2: 38400bps 0: OFF, 1: ON

MONITOR menu

PORTRAIT/LANDSCAPE INSTALL STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT HORIZONTAL INSTALLATION MLAY WR 0-1 0-1 0: OFF, 1: UPWARD OSD H-POSITION OSDH WR 0-100 0-100 OSD V-POSITION OSDV WR 0-100 0-100 POWER SAVE MODE STBM WR 0-1 0-1 0: OFF, 1: ON OFF IF NO

OPERATION

POWER ON DELAY

SELF ADJUST AADJ WR 0-1 0-1 0: OFF, 1: ON

TOUCH OUTPUT INVALID DISP.

TOUCH OPERATION MODE TOMD WR 0-1, 3 0-1, 3 0: AUTO, 1: MULTI-TOUCH MODE, 3: SINGLE-TOUCH MODE

TOUCH PANEL MODE GMDP WR 0-1 0-1 0: OFF, 1: ON (When the input mode is HDMI, D-SUB[RGB], DisplayPort,

PALM CANCEL PARE WR 0-1 0-1 0: OFF, 1: ON

Function

TIME AOFT WR 1-12 1-12 1-12: 1-12 hours

INTERVAL PWOD WR 1-60 1-60 1-60: 1-60 seconds

START TIMING AADD WR 10-200 10-200 10: 1 second through 200: 20 seconds TOUCH OUTPUT

INVALID ICON CHANGE DISPLAY

POSITION

Command Direction

ATOF WR 0-1 0-1 0: OFF, 1: ON

PODS WR 0-1 0-1 0: OFF, 1: ON

TOPI WR 0-1 0-1 0: OFF, 1: ON

TOIP WR 0-3 0-3 0: UPPER RIGHT, 1: UPPER LEFT, 2: LOWER RIGHT, 3: LOWER LEFT

Parameter Reply Control/Response contents *

“ERR” when the touch panel is not connected.

OPTION)

○

●

○

Page 52

Controlling the Monitor with a computer (RS-232C)

MULTI/PIP menu

PIP MODES MWIN WR 0-3 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 PIP SIZE MPSZ WR 1-64 1-64 PIP POS THE LONGEST

PIP POS LD+SD BATCH MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format.

PIP BLEND MWBL WR 0-7 0-7 PIP SOURCE MWIP WR 2 2 D-SUB[RGB]

SOUND CHANGE MWAD WR 1-2 1-2 1: MAIN, 2: SUB MAIN POS (Main screen) MWPP WR 0-1 0-1 0: POS1, 1: POS2 PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0: POS1, 1: POS2, 2: POS3 QUAD-SCREEN MODE MSCS WR 1, 4 1, 4 0: OFF, 1: ON SETTING INITIAL SCREEN

(POSITION 1-4)

PRIORITY: AUTO INPUT SEL.

SAVE LAST INPUT CONFIG. MSLI WR 0-1 0-1 0: OFF, 1: ON TARGET: SOUND / INPUT SEL. MSAO WR 1-4 1-4 1: POS1, 2: POS2, 3: POS3, 4: POS4

Function

DIRECTION THE SHORTEST

DIRECTION

DisplayPort1 MPDP WR 0-10 0-10 0: Not selected by PRIORITY: AUTO INPUT SEL., 1-10: Priority setting DisplayPort2 MPP2 HDMI1 MPH1

HDMI2 MPH2 HDMI3 MPH3 D-SUB MPD1

Command Direction

MHPS WR 0-100 0-100

MVPS WR 0-100 0-100

R 0-100,0-100 Returns a response in (xxx,yyy) format.

MSP1-

MSP4

WR 0 0 AUTO

Parameter Reply Control/Response contents *

3 3 D-SUB[COMPONENT]

10 10 HDMI1 13 13 HDMI2 14 14 DisplayPort1 18 18 HDMI3 21 21 OPTION (valid when you have used the expansion slot to expand the functions)

22 22 DisplayPort2

2 2 D-SUB[RGB] 3 3 D-SUB[COMPONENT]

10 10 HDMI1 13 13 HDMI2 14 14 DisplayPort1 18 18 HDMI3 21 21 OPTION 22 22 DisplayPort 2

(xxx: Longer side, yyy: Shorter side position)

○

OTHERS menu

POWER MANAGEMENT PMNG WR 0-1 0-1 0: OFF, 1: ON CONNECT AUTO INPUT SELECT AICO WR 0-1 0-1 0: OFF, 1: ON NO SIGNAL AUTO INPUT SEL. AINO WR 0-1 0-1 0: OFF, 1: ON AUTO INPUT

SELECT PRIORITY

LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON SCAN MODE

(HDMI, D-SUB[COMPONENT],

OPTION (valid when you have used the

expansion slot to expand the functions)) VOLUME VOLM WR 0-31 0-31 MUTE MUTE WR 0-1 0-1 0: OFF, 1: ON -

MUTE WITH FREEZE FRAO WR 0-1 0-1 0: OFF, 1: ON

Function

DisplayPort1 DisplayPort2 HDMI1 APH1

HDMI2 APH2 HDMI3 APH3 D-SUB APD1 OPTION APOP

Command Direction

APDP WR 0-10 0-10 0: Not selected by NO SIGNAL AUTO INPUT SEL., 1-10: Priority setting APP2

SCAN WR 0-1 0-1 0: MODE1, 1: MODE2

Parameter Reply Control/Response contents *

“ERR” when OFF is selected for NO SIGNAL AUTO INPUT SEL.. APOP will result in an error ("ERR") when an optional part that is not a target for

this function is connected.

All input terminals cannot be set to 0 simultaneously.

○

Page 53

Controlling the Monitor with a computer (RS-232C)

Initialization/Functional Restriction Setting (FUNCTION) menu

ALL RESET RSET W 0-1 0: ALL RESET 1, 1: ALL RESET 2 -

Function

ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF, 1:ON1, 2:ON2

ADJUSTMENT LOCK TARGET ALTG WR 0-2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH

OSD DISPLAY LOSD WR 0-2 0-2 0: ON1, 1: OFF, 2: ON2 LED OFLD WR 0-1 0-1 0: ON, 1: OFF TEMPERATURE ALERT TALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED STATUS ALERT SALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED POWER BUTTON PBTN WR 0-1 0-1 0: MONITOR, 1: EXT. CONTROLLER EXTERNAL CONTROLLER INPUT PCIP WR 0-3, 5, 6 0-3, 5, 6 0: D-SUB, 1: DisplayPort1, 2: HDMI1, 3: HDMI2, 5: HDMI3, 6: DisplayPort2

SIGNAL RESPONSE LEVEL HDUC WR 1-200 1-200

Command Direction

Parameter Reply Control/Response contents *

(“ERR” when MONITOR is selected for POWER BUTTON.)

Others

Function

SCREEN SIZE WIDE WR 1-5 1-5

INFORMATION MODEL INF1 R Value

SERIAL NO SRNO R Value

TEMPERATURE SENSOR DSTA R 0 Internal temperature normal

TEMPERATURE ACQUISITION ERRT R Value Returns the temperature at the temperature sensors.

CAUSE OF LAST STANDBY MODE STCA W 0 Initialization

Touch operation valid/invalid TPEN WR 0-1 0-1 0: Invalid, 1: Valid

FREEZE FUNCTION FRMD WR 0-1 0-1 0: Freeze release, 1: Freeze execute

Command Direction

R 0 No detectable error has occurred

Parameter Reply Control/Response contents *

1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2

1 Internal temperature abnormal has occurred and the monitor is in standby mode

2 Internal temperature abnormal occurred (To delete the information of temperature

abnormal, turn off the main power.)

3 Internal temperature abnormal has occurred and backlight brightness is dimmed 4 Temperature sensor abnormal

Indicates a temperature sensor abnormality when “126” is returned.

1 Standby mode by POWER button or MONITOR OFF button

2 Main power off by the main power switch 3 Standby mode by RS-232C or LAN 4 Input signal waiting mode by No Signal 6 Standby mode by abnormal temperature 8 Standby mode by SCHEDULE setting 9 Standby mode by DDC/CI

10 Standby mode by HDMI CEC 20 Standby mode by OFF IF NO OPERATION setting

“ERR” when TOUCH INPUT SELECT is set to INVALID or the touch panel is not

connected.

●

○

●

○

●

Commands for setting of the GAMMA user data

Function

RED GAMMA DATA TRANSFER UGRW W aaxxxx GREEN GAMMA DATA TRANSFER UGGW W BLUE GAMMA DATA TRANSFER UGBW W

RED GAMMA DATA READ UGRR W 1-16 xxxx GREEN GAMMA DATA READ UGGR W 1-16 BLUE GAMMA DATA READ UGBR W 1-16 USER DATA INITIALIZE UGRS W 0 Initialize the user data. USER DATA SAVE UGSV W 0 Save the user data in the monitor.

Command Direction

Parameter Reply Control/Response contents *

xxxxcc

···

(xxxx: 32 pieces)

aa: 01-16 xxxx: 0000-1023 cc: 00-FF

xxxx

···

(xxxx: 32 pieces)

xxxx: 0000-1023

aa: Block number

xxxx: 32 pieces of user data

cc: Checksum (ASCII data) of the block number and user data

xxxx: User data of 32 pieces

○

Page 54

LAN terminal

LAN cable (commercially available, straight)

Controlling the Monitor with a computer (LAN)

Your monitor can be connected to a LAN allowing you to

control it from a computer on the LAN.

You can also congure the monitor to send e-mail notication when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

Hub

TIPS

• You must assign an IP address to the monitor by following

the procedures in “Settings to connect to a LAN”. (See the description on the right.)

• Your computer must be installed with the web browser.

• When POWER SAVE MODE is set to ON, control is not

possible in standby mode.

• To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 35.)

• You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

• Personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing

of the monitor, initialize all settings by selecting ALL RESET

1. (See page 43.) Note that ALL RESET 2 will not initialize

e-mail addresses and other settings.

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a Computer connected to the monitor.

The settings depend on the conguration of your LAN. Ask your LAN administrator for details.

To set on the monitor

Set RS-232C/LAN SELECT of COMMUNICATION SETTING

on the SETUP menu to LAN, and then set the LAN SETUP

options. (See page 35.)

After setting each item, select SET and press the ENTER button.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

Press the

values with the numeric input buttons (0 to 9). You can also change the values with the

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

Press the

values with the numeric input buttons (0 to 9). You can also change the values with the

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a gateway, specify “000.000.000.000”.

Press the

values with the numeric input buttons (0 to 9). You can also change the values with the

RESET

Resets the values of the LAN settings to the factory preset

values. Select ON and then press the ENTER button.

or button to select the items, and enter the

or button.

or button to select the items, and enter the

or button.

or button to select the items, and enter the

or button.

Page 55

(commercially available, crossover)

Computer

Controlling the Monitor with a computer (LAN)

To set from a computer

When the monitor is connected to a computer, LAN settings

can be congured via computer.

Set up process

(1) Connect your monitor to a computer (2) Specify the computer’s IP address (3) Congure the monitor’s LAN settings

(1) Connecting your monitor to a computer

Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the computer and this

monitor.

LAN terminal

To LAN terminal

7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows.

• IP Address : 192.168.150.1

• Subnet Mask : 255.255.255.0

• Default Gateway : (leave blank)

8. Click [OK] and then reboot the computer.

TIPS

• This monitor is factory preset as shown below.

(When DHCP CLIENT is set to OFF)

IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0

LAN cable

(2) Specifying the computer’s IP address

To congure the monitor’s LAN settings, you must temporarily

change the settings on the computer.

This explanation is based on Windows 7.

1. Log on to the computer with an administrator account.

2. Click [Start], and then click “Control Panel”.

3. Click “View network status and tasks” in “Network and

Internet”.

In “Classic View”, click “Network and Sharing Center”.

4. Click “Local Area Connection” and then “Properties”.

5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then

“Properties”.

6. Make a note of the current IP address, subnet mask, and default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

(3) Conguring the monitor’s LAN settings

Access the monitor using the web browser.

Controlling the monitor

1. Turn the power ON to the monitor.

2. Set RS-232C/LAN SELECT of COMMUNICATION

SETTING on the SETUP menu to LAN.

3. Set DHCP CLIENT of LAN SETUP of COMMUNICATION SETTING on the SETUP menu to OFF.

Computer operation

4. Launch the web browser, in the “Address” box type “http://192.168.150.2/” and press the Enter key.

5. Enter the USER NAME and PASSWORD. The following values are set in the initial settings.

USER NAME: admin, PASSWORD: admin

* To enable security on the monitor, change the user

name and password. (See page 58.)

Page 56

Controlling the Monitor with a computer (LAN)

6. Click on “LAN SETUP” under NETWORK.

7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.

Controlling with a computer

Basic operation

You use the web browser on a computer on the LAN to control the monitor.

1. Launch the web browser on the computer.

In the “Address” box, type “http://” followed by your monitor’s IP address followed by “/”, then press the Enter key.

You can conrm the IP address with the INFORMATION

function.

When prompted to enter a USER NAME and PASSWORD, type the user name and password that you specied in the

SECURITY settings (see page 58.), and click [OK]. The following values are set in the initial settings.

USER NAME: admin, PASSWORD: admin

* To enable security on the monitor, change the user

name and password. (See page 58.)

3. You can check, control, and change the monitor’s status and settings by clicking the menu items on the left side of the screen.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

8. When the setting is changed, click [Apply].

9. Check the message and click [OK]. 10

. Exit the web browser.

. Restore the computer’s IP address jotted in Step 6, “(2)

Specifying the computer’s IP address”.

12.

Connect the monitor and the computer to the LAN.

Caution

• Wait 10 seconds after clicking [OK] before proceeding.

• When operating using the remote control unit or similar, click [Refresh].

• If you see an [Apply] button next to a setting, click it after you change that setting.

TIPS

• See pages 57 to 61 for details on each setting.

• If you click [Refresh] before the screen nishes updating

the current display, the “Server Busy Error” will appear. Wait for a moment before operating your monitor again.

• You cannot operate the monitor while it is warming up.

• If “DHCP CLIENT” is set to “ON”, press the INFORMATION

button on the remote control unit two times and then check the monitor’s IP address.

Page 57

Controlling the Monitor with a computer (LAN)

INFORMATION

Information about this monitor appears.

CONTROL

You can control the operations corresponding to the buttons (POWER button, INPUT button, SIZE button, etc.) on the remote control unit. (See page 26.)

ADJUSTMENT

You can adjust these settings which are also available on the monitor’s menu.

• SCREEN (See page 31.)

• PICTURE (See pages 32 to 33.)

• AUDIO (See page 33.)

• SETUP (See pages 34 to 35.)

• MONITOR (See page 36.)

• SCHEDULE (See page 40.)

• PIP/PbyP (See page 37.)

• OTHERS (See page 38.)

• FUNCTION (See page 43.)

• CONFIGURE QUAD-SCREEN (See page 37.)

TIPS

• In standby mode, Power ON is the operation available.

TIPS

• After changing DISPLAY COLOR PATTERN to OFF, click [Refresh] to correctly retrieve the status of the monitor.

Page 58

Controlling the Monitor with a computer (LAN)

NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the monitor is connected to a LAN.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

DNS SERVER ADDRESS AUTO ACQUISITION

If the DHCP CLIENT is set to ON, specify whether or not to automatically obtain the DNS server address.

DNS SERVER

Specify the DNS server address if the DHCP CLIENT is set to OFF or the DNS SERVER ADDRESS AUTO ACQUISITION is set to OFF. If you are not using a DNS server, specify “0.0.0.0”.

RESET

Clicking [Execute] returns all of the LAN SETUP settings to the factory-preset values except for the DNS SERVER ADDRESS AUTO ACQUISITION and DNS SERVER settings.

NETWORK (SECURITY)

This screen allows you to specify the security-related settings.

USER NAME / PASSWORD

Sets up a user name and password to restrict access to this monitor. The following values are set in the initial settings.

USER NAME: admin, PASSWORD: admin

* To enable security on the monitor, change the user name

and password.

After entering a user name and password, click [Apply].

USE FOR Telnet CONNECTION

Sets whether to use a user name and password when connecting over TELNET.

ACCEPT IP ADDRESS

You can limit access to this monitor by registering IP addresses of computers that should have access.

To limit access, specify the option “From only specic IP

addresses”. Otherwise, to allow access from any computer, specify “All IP Addresses”.

IP ADDRESS 1 to 3

If “ACCEPT IP ADDRESS” is set to “From only specic IP

addresses”, enter the IP addresses that you want to allow.

TIPS

• The USER NAME and PASSWORD can be up to 8

alphanumeric characters (hyphens and underscores allowed).

• To cancel the user name and/or password after it has been set, make the box empty and click [Apply].

Page 59

Controlling the Monitor with a computer (LAN)

NETWORK (GENERAL)

This screen allows you to specify the general LAN settings.

MONITOR NAME

Specify a name for this monitor as it should appear on the web browser screen.

AUTO LOGOUT TIME

Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function.

DATA PORT

Specify the TCP port number to use for exchanging data with the monitor. Specify a value from 1025 to 65535.

SEARCH PORT

Specify the port number to use when searching for this monitor. Specify a value from 1025 to 65535.

INSTALLATION INFORMATION (NAME/LOCATION)

Specify the information to display for this monitor in the web browser window.

LINK MODE

Selects the link speed and duplex. Use AUTO normally.

TIPS

• The MONITOR NAME can be up to 16 alphanumeric

characters or symbols.

• Enter up to 50 characters in the NAME eld in the INSTALLATION INFORMATION.

• Enter up to 100 characters in the LOCATION eld in the INSTALLATION INFORMATION.

MAIL (ORIGINATOR)

This screen allows you to congure the e-mail sent periodically

or when the monitor has an error.

The settings depend on the conguration of your LAN. Ask

your LAN administrator for details.

SMTP SERVER

Specify the SMTP server address for sending e-mail.

* When using a domain name, make sure to specify the

DNS SERVER as well. (See page 58.)

SMTP PORT

If the “AUTHENTICATION” is “SMTP-AUTH”, specify the port

number.

ORIGINATOR E-MAIL ADDRESS

Specify the e-mail address for this monitor. This address becomes the e-mail address of the originator.

ORIGINATOR NAME

Specify the name for the originator.

This name appears in the “Originator Name” eld of the

e-mail.

AUTHENTICATION

Specify the authentication method to use when sending e-mail.

POP SERVER

If the “AUTHENTICATION” is “POP before SMTP”, specify

the POP server address.

ACCOUNT NAME / PASSWORD

If the “AUTHENTICATION” is “POP before SMTP” or “SMTP-AUTH”, specify the account name and password to connect to the SMTP server.

TIPS

• You can enter up to 64 alphanumeric characters or symbols

for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR NAME, ACCOUNT NAME, and PASSWORD.

• The SMTP SERVER and POP SERVER can be up to 64

characters.

The following characters can be used: a-z, A-Z, 0-9, - , .

Page 60

Controlling the Monitor with a computer (LAN)

MAIL (RECIPIENT)

This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSES

Specify the e-mail addresses to send error notication e-mail

to.

CONDITION

Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting.

CONFIRMATION

Sends test e-mail.

This allows you to conrm that the e-mail settings are congured properly.

Attach the log le to a TEMPERATURE/HARDWARE error

e-mail.

When this option is checked, a log is added to the mail which

noties a temperature or status error.

E-MAIL TRANSMISSION ERROR REPORT

A report of the latest e-mail transmission errors will be displayed. The error report will be displayed when an e-mail transmission error occurs. Also, the e-mail transmission errors will be cleared when ALL RESET1 is executed. (See page 43.)

MAIL (PERIODICAL)

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is

checked, set the date and time to send the mail.

DAY OF THE WEEK

Specify the day of the week to send the periodical mails.

TIME

Specify the time of the day to send the periodical mails.

Caution

• Do not turn off the main power when you set to send the periodical mails.

• Specify the correct date and time. (See page 34.) If the date and time settings are incorrect, the periodical mail is not sent properly.

• Regularly conrm that the specied date and time is

correct.

TIPS

• The RECIPIENT E-MAIL ADDRESSES can be up to 64

alphanumeric characters or symbols.

Page 61

Controlling the Monitor with a computer (LAN)

SNMP

You can congure settings related to SNMP.

TIPS

• Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 5 minutes)

• Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password.

SERVICE & SUPPORT

(URL INFORMATION)

You can display a specic URL in the URL INFORMATION eld on the INFORMATION screen when an error occurs in

the monitor. (See page 57.)

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Set the name of the community required for the access.

USER 1 to 3

Set the user name, password, authentication method and other options required for access.

TRAP SETTING

Set whether to enable or disable the trap function. When this function is enabled, a trap will be sent when the monitor is turned on. A test transmission of a trap can be performed in “Test”.

TRAP SETTING OF AUTHENTICATION ERROR

Set whether the trap function sends a notication when

authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the

notication sent by the trap function.

Caution

• After you set SNMP, click [Switch the main power of

monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

• If the IP address is changed while the SNMP function is

operational, turn off the monitor and then turn it on again with the main power switch.

URL INFORMATION

Enter the URL to display on the INFORMATION screen when

an error occurs on the monitor. Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

The home page of the specied URL is displayed.

You can check whether the URL you entered is correct.

TIPS

• It is also possible to specify the message text, such as the name of a contact or a telephone number, to be displayed instead of the linked URL.

Page 62

Controlling the Monitor with a computer (LAN)

Crestron Connected

Display the Crestron Connected control menu.

Control Menu

1. Operate below functions.

• Power.........Turn the power ON/OFF.

• Mute ...........Turns off the volume temporarily.

• Vol-/Vol+ ....Adjust the volume of the sound.

2. Change the input mode.

3. Operate below functions.

• Contrast ........ Adjusts the contrast.

• Black Level ... Adjusts the brightness.

• Colors ........... Adjusts the color intensity.

• Sharpness..... Adjusts the sharpness.

4. Operates the menu screen for the monitor.

5. Switches the pages to tools, information, help tab.

Tools

Info

1. Display below information.

• Display Name

• Mac Address

• Resolution

2. Display below status.

• Power Status

• Input

Help

Sends or receives messages to the administrators who uses “Crestron Connected”.

1. Setting for Crestron Control.

2. Setting for monitor network.

• DHCP

• IP Address

• Subnet Mask

• Default Gateway

3. Security Setting. Sets the password for the user and administrators rights on Control Menu.

Page 63

Controlling the Monitor with a computer (LAN)

[Advanced operation] Command-based control

You can control the monitor using RS-232C commands

(see page 47) via terminal software and other appropriate

applications. In order to use this function, enable a connection to the

monitor through the web browser. Read the manual for the terminal software for detailed

instructions.

(1) Connect the computer to the monitor.

1. Specify the IP address and data port number and

connect the computer to the monitor.

When connection has been established successfully,

[

2. Send the user name set in the SECURITY settings.

(See page 58.)

• Send [user name] + [

• If the user name is not set or if USE FOR Telnet CONNECTION is set to OFF, send [

• When the transmission is successful, [ is returned as response.

3. Send the password set in the SECURITY settings. (See page 58.)

• Send [password] + [

• If the password is not set or if USE FOR Telnet

CONNECTION is set to OFF, send [

• When the transmission is successful, [OK

returned as response.

(2) Send commands to control the monitor.

• The commands used are the same as those for RS-

232C. Refer to the communication procedure (see page 44) for operation.

• Usable commands are provided in the RS-232C

command table. (See page 47.)

(3) Disconnect the connection with the monitor and

quit the function.

1. Send [BYE ]. When the transmission is successful, [goodbye] is

returned and the connection is disconnected.

Password:]

] is

TIPS

• Connection is automatically disconnected when the time specied in AUTO LOGOUT TIME elapses over a

no-communication period.

Page 64

Troubleshooting

If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting

tips.

There is no picture or sound.

• Is the power cord disconnected? (See page 14.)

• Is the main power switch off? (See page 17.)

• Is the monitor in standby mode (the power LED illuminating in orange)? (See page 17.)

• Is an input mode selected that is appropriate for the input

terminal to which the cable is connected? (See pages 24

and 27.)

• If any external equipment is connected, make sure the equipment is operating (playing back).

Remote control does not work.

• Are the batteries inserted with polarity (+,-) aligned? (See page 15.)

• Are the batteries exhausted?

• Point the remote control unit toward the monitor’s remote control sensor. (See page 15.)

• Is the menu display hidden or is operation disabled? (See

page 43.)

• Do the remote control numbers on the remote control unit

and on the monitor match?

Check the numbers on INFORMATION. (See page 41.)

Sound from left and right speakers is reversed. Sound is heard from only one side.

• Are audio cables connected properly? (See page 13.)

• Make sure audio cables for external speakers are connected properly: left and right cables may be reversed or one of the two cables may not be connected. (See page

13.)

• Check the setting of BALANCE for AUDIO menu. (See

page 33.)

There is a picture but no sound.

• Is the sound muted?

• Make sure the volume is not set to minimum.

• Are audio cables connected properly?

• Is the setting of AUDIO SELECT on the SETUP menu

correct? (See page 34.)

• Is the setting for SPEAKER SELECT of AUDIO OPTION on

the SETUP menu correct? (See page 35.)

Unstable video.

• The signal may be incompatible.

• Try the automatic screen adjustment when D-SUB[RGB] is

used.

• If the top and bottom of the image are not horizontally

aligned, set TOUCH PANEL MODE on the MONITOR menu to OFF.

The video from the HDMI input terminal does not appear properly.

• Does the HDMI cable support 4K, and is it HDMI standard

compliant? The monitor will not work with cables that are

not standard compliant.

• Is the input signal compatible with this monitor? (See pages

68 and 69.)

• If the connected device is not 4K compliant, set HDMI MODE to MODE 2.

The video from D-sub input terminal does not appear correctly.

• Is the setting for D-SUB of INPUT SELECT on the SETUP

menu correct? (See page 34.)

• Is the input signal compatible with this monitor? (See pages

68 and 69.)

The video from DisplayPort input terminal does not appear correctly.

• Is the input signal compatible with this monitor? (See page

68.)

• Does the DisplayPort cable support 4K, and is it DisplayPort standard compliant? The monitor will not work with cables that are not standard compliant.

• Restart the monitor and your computer.

• Is the video card DisplayPort1.2 compliant?

If not DisplayPort1.2 compliant, set DisplayPort STREAM to SST1.

• Is the video card multi-stream compliant? If not multi-stream compliant, multi-stream cannot be used

even if DisplayPort STREAM is set to MST.

• The DisplayPort1 input terminal does not support multi- stream.

To use multi-stream, use the DisplayPort2 input terminal and set DisplayPort STREAM to MST.

Control buttons do not work. There is no picture.

• Load noises from outside may be interfering with normal operation. Turn off the main power and turn it on after waiting at least 5 seconds, and then check the operation.

The input mode changes automatically.

• When CONNECT AUTO INPUT SELECT is ON, the input

mode automatically changes to that terminal when a video

signal is input into the input terminal.

For this reason, the input mode may change when the computer wakes up from system standby.

• When the NO SIGNAL AUTO INPUT SEL. is ON and no signal is present in a selected input mode, the monitor

automatically changes the selected mode to a mode where

a video signal is present.

The input mode may change in the following cases:

- When a computer is in standby mode.

- When video play is stopped with a playback device.

Page 65

Troubleshooting

The touch panel does not respond.

• Is the USB cable connected properly? (Touch pen

Management Tool Operation Manual)

The monitor has two USB ports (for a touch panel). The

USB port that can be used to connect a touch panel

depends on the terminal to which the computer’s video signal cable is connected. (See pages 13 and 35.)

• Has Touch pen Management Tool been installed? (Touch

pen Management Tool Operation Manual)

• Has the pen tip of the touch pen become worn? Replace the pen tip. (See page 21.)

• Is the battery inserted in the wrong orientation (+, -) in the touch pen? (See page 19.)

• Is the touch pen battery exhausted?

• Are touch pens that are supplied touch pens or optional

PN-ZL06 used?

• If your nger is too dry, the screen may not respond.

• Is foreign matter on the screen? Foreign matter on the screen may prevent correct

operation.

• Do not touch the screen when the monitor power is turned on, it will lead to a malfunction. When this occurs, turn the monitor power off and then on.

Power LED illuminates in blue and orange alternately. “STATUS [xxxx]” appears in the corner of the screen.

• Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer.

(When STATUS ALERT is set to OSD & LED. This varies depending on the setting.)

When “AUTO DIMMING” is displayed.

• When the internal temperature of the monitor rises

excessively, the brightness of the backlight automatically

decreases in order to prevent a further temperature rise. If

you attempt to adjust the brightness while the monitor is in this state, “AUTO DIMMING” is displayed and you cannot

change the brightness.

• Remove the cause of the excessive temperature rise.

The monitor makes a cracking sound.

• You may occasionally hear a cracking sound from the monitor. This happens when the cabinet slightly expands

and contracts according to change in temperature. This does not affect the monitor’s performance.

The Power LED is ashing in orange and blue alternately. When “TEMPERATURE” is displayed in the corner of the screen.

• When the internal temperature of the monitor rises

excessively, the brightness of the backlight decreases automatically in order to prevent high-temperature-

related problems. When this occurs, “TEMPERATURE” is

displayed on the screen and the Power LED ashes orange and blue alternately. (When TEMPERATURE ALERT is set

to OSD & LED. This varies depending on the setting.)

• If the internal temperature rises further, the monitor

automatically enters standby mode. (The Power LED continues ashing orange and blue alternately.)

• Remove the cause of the excessive temperature rise.

- If the monitor enters standby mode due to a rise in temperature, to return to normal display, turn the power switch off and then back on again. The monitor, however, will enter standby mode again if the cause of the

temperature rise is not eliminated. (See page 7.)

- Check whether the monitor is placed at a location where a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked.

- Internal temperature rises quickly if dust accumulates

inside the monitor or around the vents. Remove dust if

possible. Ask SHARP dealer about removing internal dust.

Page 66

Specications

Product Specications

Model PN-L705H LCD component Max. resolution (pixels) Max. colors Pixel pitch

Brightness (typical) 300 cd/m Contrast ratio (typical) 4000: 1

Viewing angle

Screen active area inch (mm) Computer input signal

Sync signal Plug and play Power management

Input terminals

Video HDMI x 3

Audio Serial (RS-232C)

Output terminals

Video Audio

LAN terminal 10 BASE-T/100 BASE-TX

Speaker output (internal/external) 10 W + 10 W/10 W + 10 W

Touch Panel

Detection method Capacitive type Computer connector USB (2.0 compliant) (Type B) x 2

Touch pen Wireless communication method

Touch pen adapter port

Power requirement AC 100 V - 240 V, 3.2 A, 50/60 Hz

Operating temperature

Operating humidity

*3*

Power consumption

(Input signal waiting mode

standby mode

)

Dimensions (excluding protrusions) inch (mm) Weight lbs. (kg)

*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the

equipment, it is not possible to precisely maintain a constant level of brightness. *2 D-sub input terminal only. *3 When using the monitor laying at on a surface (when the monitor is tilted more than 20 degrees upward from the perpendicular in relation

to a level surface), use the monitor at a temperature between 41°F (5°C) to 86°F (30°C).

Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.

In such cases, please check the temperature condition specied by the optional equipments. *4 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satised. *5 When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF.

*6 When POWER SAVE MODE is set to OFF. When POWER SAVE MODE is set to ON: xx W

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from

these values in individual units.

70" Class [70 inch (176.6cm) diagonal] TFT LCD 3840 x 2160 Approx. 1.06 billion colors

0.923 mm (H) × 0.923 mm (V)

176° right/left/up/down (contrast ratio ≥ 10) 60-9/16 (W) x 34-1/16 (H) (1538.9 x 865.6)

Analog RGB (0.7 Vp-p) [75 Ω], HDMI, DisplayPort 1.2a

Horizontal/vertical separate (TTL: positive/negative), Sync-on-green

VESA DDC2B VESA DPMS

Mini D-sub 15 pin, 3 rows x 1 DisplayPort x 2

3.5 mm mini stereo jack x 1

3.5 mm mini jack x 1 DisplayPort x 1

3.5 mm mini stereo jack x 1

6 Ω

(2.4GHz, Bluetooth Low Energy, FHSS method) USB (2.0 compliant) (Type A)

41°F to 95°F (5°C to 35°C) 20% to 80% (no condensation) xx W (xx W / xx W)

Approx. xx (W) x xx (D) x xx (H) (xx x xx x xx) Approx. xx (xx)

Page 67

Dimensional Drawings

Unit: inch [mm]

xx [xx]

[xx]

Note that the values shown are approximate values.

Specications

)

xx [xx]

(

[xx]

xx [xx]

Opening width (xx [xx])

Opening height

xx [xx]

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor.

Power management

This monitor conforms to VESA DPMS. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.

DPMS: Display Power Management Signaling

DPMS Screen

ON STATE Display xx W Yes Ye s

STANDBY

SUSPEND Yes No

display

OFF STATE No No

Power

consumption

xx W*

Hsync Vsync

No Yes

* When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF.

Page 68

*4 Compatible when HDMI MODE is MODE1.

Specications

DDC (plug and play)

The monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. This function can be used if the computer supports DDC and it has been congured to detect plug-and-play monitors. There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

Compatible signal timing (PC)

Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes

Digital

Yes Yes Yes

Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes

Yes

Screen resolution

VESA

640 × 480

Vsync

60Hz

DisplayPortHDMI

72Hz 75Hz

800 × 600

56Hz 60Hz 72Hz 75Hz

848 × 480

1024 × 768

60Hz 60Hz 70Hz 75Hz

1152 × 864

1280 × 768

75Hz 60Hz

75Hz 1280 × 800 1280 × 960

1280 × 1024

60Hz

75Hz

60Hz

24Hz

Wide

1360 × 768

1400 × 1050

1440 × 900

1600 × 1200 1680 × 1050 1920 × 1200 3840 × 2160

25Hz

30Hz

50Hz

60Hz

24Hz

4096×2160

25Hz

30Hz

50Hz

60Hz

70Hz

60Hz

US TEXT Sun

1280 × 720

1920 × 1080

720 × 400

1024 × 768

66Hz

70Hz

1152 × 900

66Hz

76.2Hz

1280 × 1024

67.2Hz 76Hz

1600 × 1000

*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed. *2 Compatible when DisplayPort STREAM is SST1 or SST2. *3 Compatible when DisplayPort STREAM is SST2.

66Hz

Analog

(D-SUB)

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

• Depending on the connected computer, images may not be displayed properly even if the compatible signal described above is input.

• The frequency values for the Sun are reference values.

Page 69

Compatible signal timing (AV)

Screen resolution Frequency HDMI Component

4096 × 2160p 24Hz Ye s -

3840 × 2160p 24Hz Ye s -

1920 × 1080p 24Hz Ye s -

1920 × 1080i 50Hz Yes Yes

1280 × 720p 50Hz Yes Yes

720 × 576p 50Hz Ye s Ye s 720 × 480p 59.94Hz Yes Yes

640 × 480p 59.94Hz Yes -

720(1440) × 576i 50Hz Yes Yes 720(1440) × 480i 59.94Hz Yes Yes

* Compatible when HDMI MODE is MODE1.

Specications

25Hz Yes* - 30Hz Yes* - 50Hz Ye s -

59.94Hz Yes 60Hz Ye s -

25Hz Ye s 30Hz Ye s 50Hz Ye s -

59.94Hz Yes 60Hz Ye s -

50Hz Ye s Ye s

59.94Hz Yes Yes 60Hz Ye s Ye s

60Hz Ye s Ye s

60Hz Ye s -

60Hz Ye s Ye s

Page 70

Specications

D-sub input terminal pins

(Mini D-sub 15 pin)

No. Function No. Function

1 Red video signal input 9 +5V 2 Green video signal input 10 GND 3 Blue video signal input 11 N.C. 4 N.C. 12 DDC data 5 GND 13 Hsync signal input 6 GND for red video signal 14 Vsync signal input 7 GND for green video signal 15 DDC clock 8 GND for blue video signal

HDMI input terminal pins

(HDMI Connector)

No. Function No. Function

1 TMDS data 2+ 11 TMDS clock shield

2 TMDS data 2 shield 12 TMDS clock- 3 TMDS data 2- 13 CEC 4 TMDS data 1+ 14 N.C. 5 TMDS data 1 shield 15 SCL 6 TMDS data 1- 16 SDA 7 TMDS data 0+ 17 DDC/CEC GND 8 TMDS data 0 shield 18 +5V 9 TMDS data 0- 19 Hot-plug detection

10 TMDS clock+

DisplayPort input terminal pins

(DisplayPort 20 pin)

No. Function No. Function

1 MainLane 3- 11 Gnd 2 Gnd 12 MainLane 0+ 3 MainLane 3+ 13 Gnd 4 MainLane 2- 14 Gnd 5 Gnd 15 Aux + 6 MainLane 2+ 16 Gnd 7 MainLane 1- 17 Aux 8 Gnd 18 Hot-plug detection 9 MainLane 1+ 19 Gnd

10 MainLane 0- 20 3.3V

DisplayPort output terminal pins

(DisplayPort 20 pin)

No. Function No. Function

1 MainLane 0+ 11 Gnd 2 Gnd 12 MainLane 33 MainLane 0- 13 Gnd 4 MainLane 1+ 14 Gnd 5 Gnd 15 Aux + 6 MainLane 1- 16 Gnd 7 MainLane 2+ 17 Aux 8 Gnd 18 Hot-plug detection 9 MainLane 2- 19 Gnd

10 MainLane 3+ 20 3.3V

Page 71

Mounting Precautions

(For SHARP dealers and service engineers)

• When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people.

• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.

• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation. This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness of the mounting bracket.

5/16 - 3/8 inch (8-10 mm)

Screws (M6) Mounting bracket Monitor mounting

• Do not use an impact driver.

• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.

• Do not use any screw holes other than VESA holes for installation.

• When moving this monitor, hold with the handles or at the sides of this monitor, and hold the top and bottom of this monitor. Do not grasp the screen, monitor corner, tray, speaker, or speaker cover. This may cause product damage, failure, or injury.

• If you need to temporarily place the monitor on a table or other surface during installation, spread a thick soft cloth on the

table to prevent damage to the screen and table.

• Prior to repacking or removal, remove the tray and speaker covers.

• When using the monitor laying at on a surface (when the monitor is tilted more than 20 degrees upward from the perpendicular in relation to a level surface), consult an authorized SHARP dealer because there are some specic mounting

conditions.

Attaching the Tray

Tray mount fitting

Caution

• When attaching the tray, do not pinch the USB cable on the back of the tray.

The USB cable on the back of the tray can be fastened with the cable clamp to the rear of the monitor.

*1 *1

Push until the tabs lock into place (4 places)

Tabs (4 places)

Page 72

Mounting Precautions (For SHARP dealers and service engineers)

Removing the Tray

Back of the tray

Pinch the locking tabs (4 places)(1)

Attaching the speaker covers

(2)

Speaker cover attachment screws (M3)

If you will use the monitor in a portrait orientation, the speaker cover is not used.

Removing the tray mount tting

If you will use the monitor in a portrait orientation or will otherwise not use the tray, remove the tray mount tting.

Page 73

PN-L705H M EN17J(1)