Page 1
The product is subject to change without notice.
The graphs in this instruction manual may be different
from the actual products; please refer to the actual products.
AIR COOLER
PJ-A77TV-B
Page 2
Safety Notices
1.Use normal power supply 220-240V~ 50Hz and use the
independent 3A or 3A above socket which with national
standard to ensure the safety (see fig 1).
2.After the unit is filled with water, please push the unit
slowly if you have to move the unit to prevent water
overflowing. Prohibit tilting the unit during operation to
prevent accident. (see fig 2)
220-240V~ 50Hz
fig 1
fig 2
3.Do not put heavy objects on the top of the unit. Prohibit
covering air outlet and air inlets at both sides (see fig 3).
There should be no objects within 1m away from the unit.
Air inlet Air inlet
fig 3 fig 4
4 This unit is not applicable to be used in high-temperature
environment. Do not put the unit at a high-temperature or
low-temperature place. Water inside the water tank may be
deteriorated easily in summer, please replace water in
time. When room temperature is lower than 0ഒ, please
use warm water for humidifying. After operation is
finished, dry the water in water tank with towel in time.
5.Use wet cloth (or add some detergent) to wipe the outer
surface of the unit. Do not use corrosive abluent or
solvent to clean the surface. Prohibit washing the unit
with water(see fig 4).
-1-
Page 3
6.If it needs to be stored or transported, drain out the water,
operate at normal wind mode for approx. 30 mins to dry up
the evaporator and then pack the unit.
7.When the unit will not be used for a long time, please pull
out the power plug to prevent damage to the unit.
8.If the supply cord is damaged, it must be replaced by the
manufacturer, its authorised service agent to avoid hazard.
9.The unit is with humidifying effect; please do not operate
the unit in enclosed environment. If you operate the unit in
enclosed environment, please turn off humidifying and
cooling function.
10.When water level is lower than the minimum water level,
please add water in time.
11.This appliance is not intended for use by persons
(including children)with reduced physical, sensory or
mental capabilitiesor lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
12.Note:Before maintenance or disassembling the outer case,
the unit must be disconnected with the power supply..
13.Unplug the appliance during water filling and cleaning.
ʗ
14.Ensure that the unit is switched off from the supply mains
before removing the guard.
15.This product is only for household use.
Product Features
Standby: Once the unit is turned on, all indicators will be on for 1 second.
Then, the unit will enter standby status.
ʒON/OFF button: Press this button to turn on the unit under standby mode. The
default working status is level 1 normal wind; Press this button again to turn off
the unit.
ʓAir swing button: under working status, press this button to select air swing.
Pressing this button repeatedly can select fan mode circularly.
When swinging, the corresponding icon will light up.
ʔFan Speed button: Under working status, press this button to set fan speed.
Press this button repeatedly to select fan speed circularly.
ʕWind Mode button: Press this button under working status to select fan mode.
Press this button continuously to select fan mode circularly in the sequence of:
natural wind ĺ sleeping wind ĺ normal wind. There's no icon for general wind.
If selecting natural wind or sleeping wind, corresponding icon will be turned on.
ʖTimer button:
Timer off function: Press this button under working status to set timer off
function. Press this button continuously to set timer off time circularly in the
sequence of 1hĺ2hĺ3hĺ……ĺ15h.
Timer on function: Press this button under standby status to set preset on
function. Press this button continuously to set preset on time circularly in the
sequence of 1hĺ2hĺ3hĺ……ĺ15h. When preset on time is reached, preset
indicator is off and the fan will be turned on automatically. The defaulted preset
working status is low speed, normal wind, 2h timer off and air swing.
ʗCooling button: Press this button once under working status to start up
cooling function. Water pump will start working and cool indicator is on.
Press this button again to stop cool function. Water pump stops operation and
cool indicator will be off.
ʘLight button: Press this button for the first time and all indicators light will be
turned off; press this button again and indicator light will be turned on.
-2-
-3-
Page 4
Water level protection: When the water level is low, water pump
will stop operation and buzzer will beep three times to alarm low water level. Cooling indicator is flashing. Under cooling mode, fan motor won't be
affected during low water level protection; (This function is only valid when
cooling function is turned on).
Note: After opening the air intake panel, the unit will be turned off automatically.
Specifications
Model
PJ-A77TV-B
Rated Power
Supply
220-240V~ 50Hz
Rated
Power
=
Noise
ʇJ(A)
Water Tank
Capacity
7.0/
Evaporation
Capacity
1000mLh
Air Volume
40StN
Type
Cooling
Outline Structure and Parts' Name
Operating Console and Display Panel
Air Guide, Swing Louver
Panel Clasp
Air Inlet
Air Intake Panel
Power Cord Hooker
Water Tank (Inside)
Castor (With brake)
ུ
ཱུ
ཱི
Natural wind
Sleeping wind
Displayed icon illustration
Cooling
Remote control x1
(batteries included)
ཱ
ི
Accessories
Timer On
Timer
Swing
Ice pack x4
ུ
ཱ
ཱུ
ྲྀ
Note: Water consumption will vary, depending on different of ambient
humidity.
Operation Instruction
1.Unpack the carton box, take out the unit and check if all accessories are
available.
2.Add water: rotate the water tank lock in clockwise direction and then
draw out the water tank (see fig 3).
Note: Before adding water, please remove the pearl wool sticking at the left side
of water tank.
Ƈ When using the unit for the first time or the unit hasn't been used for a long
time, please use clean water. Pull out the power plug before adding water to
prevent electrical hazard.
Ƈ Add water to “max water level” as indicated to prevent overflow.
3.Push in the water tank, rotate the water tank lock in an anticlockwise to secure
the water tank (see fig 2), and then install the air intake panel (see fig 1).
water tank
Maximum water level
Minimum water level
ི
ཱི
(fig 1)
4.Operation of remote controller: the functions for some buttons on remote
controller are same with those for buttons on control panel. Point the infrared
transmitting tube at the main body directly. There should be no obstacles
between the remote controller and the unit.
5.Storage: If the unit will not be used for a long time, pour out the water from the
water tank completely, and then operate it at room temperature for approx.
lock of
water tank
(fig 2) (fig 3)
water tank
-4-
-5-
Page 5
30mins to dry the evaporator. Cover the unit with plastic bag, and then put it
carton box for storage.
6.Cleaning: When the unit has been operated for a long time, water tank, filter of
water tank, evaporator and filter of evaporator will be blocked by sediment
and the air volume and cooling effect will be decreased. It is recommended
to clean them every two weeks.
Cleaning method:
(1)Pull out power plug from wall power socket.
(2)Press the clasp of panel with both hands, and then open the air intake panel
(see fig 1).
(3)Unlock the water tank by turning the lock clockwise.
(4)Draw out water tank (see fig 3), and then remove the filter of water tank (see
fig 4).
(5)Remove the filter of evaporator, and then remove the evaporator (see fig 5).
Operation Instruction for Ice Pack
1.During operation, prohibit opening the ice pack cover or
consuming the gel in ice pack is strictly prohibited.
ice pack
2.Put the ice pack in the freezer to freeze for about 4h,
and then put 2 packs into the water tank (add water inside
water tank before putting the ice box in water tank).
3.The ice pack will reduce the water temperature and
produce cool air flow.
4.The equipped ice packs can be used repeatedly by rotating 2 packs in use and
2 packs standby in frozen condition.
5.Please make sure to insert the ice pack at the designated location to prevent
damage to the water pump.
Troubleshooting
Filter of water tank
Fig 4
Fig 5
Fixed rack of evaporator
Filter of evaporator
(6)Wash the water tank, filter of water tank, evaporator and filter of evaporator
with clean water, and then reinstall them correctly and securely.
Evaporator
Filter of
evaporator
Filter of
water tank
(7)Put the evaporator at the appointed position of the unit. Otherwise, it may
affect the normal operation and service life. (even the motor may be burnt out)
(8)When moving the unit, please check whether there's water inside water tank.
If yes, please drain the water out completely.
Note: Prohibit tilting and pulling the unit when there's water inside water
tank to prevent water overflow.
Malfunction Causes
1.Not put through the power
No wind
No power
Can't turn
on the unit
There's
abnormal
sound
No cooling
Can't change
the wind direction
2.Hasn't turn on the unit
3.The body is damaged
Air-in panel hasn't been
installed well
The body is damaged
1.There's sediments inside
the unit
2.The impeller is loose
3.Malfunction of motor
1.The strainer at the air inlet
is blocked
2.Water channel is blocked
3.Other causes
Malfunction of synchronous
motor
Troubleshooting
1.Insert the power cord by the correct
method
2.Press ON/OFF button to start up the
unit
3.Send it to maintenance center
Install the air-in panel tightly
Send it to maintenance center
1.Remove filter and then take
out the sundries
2.Send it to maintenance center
3.Send it to maintenance center
1.Clean the filter at the water inlet
2.Clean the water channel
3.Send it to maintenance center
Send it to maintenance center
-6-
-7-
Loading...