SHARP PC 357NJ0000F Datasheet

PREPARED By: DATE:

SPEC. No. ED-97136

SHARP

ch-\ ,w J&&/.-i /ti,,99c

APPROVED BY: DATE: ELECTRONIC COMPONENTS

“: :y

- ,/

i. 1

‘3 5 ILMZ~~

r^ i

>3p ’

,‘$‘..

i

f DEVICE SPECIFICATION FOR

GROUP SHARP CORPORATION REPRESENTATIVE DIVISION

SPECIFICATION

Business dealing name

ISSUE

PAGE 14 Pages

OPTO-ELECTRONIC DEVICES DIV

September 8, 1997

PHOTOCOUPLER

MODEL No.

1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.

2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

(1) This product is designed for use in the following application areas ;

l

l

OA equipment

l

Telecommunication equipment (Terminal)

l

Tooling machines

[

If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (31, please be sure to observe the precautions given in those respective paragraphs.

(21 Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;

* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals - Gas leakage sensor breakers * Rescue and security equipment

* Other safety equipment

[

(3) Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as ;

* Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment m Medical equipment

[

(4) Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs _

3. Please contact and consult with a Sharp sales representative for any questions about this product.

CUSTOMER’S APPROVAL

Audio visual equipment l Home appliances

* Measuring equipment

l

Computers

DATE
PRESENTED

BY

1

1

1

~gj?/

DATE

BY

T. Matsumura,

Department General Manager of
Engineering Dept. ,I1
Opto-Electronic Devices Div.
ELECOM Group

SHARP CORPORATION

SHARP CORPORATION

1. Application
This specitication applies to the outline and characteristics of photocoupler

Model No. PC357.

2. Outline
Refer to the attached drawing No. CY9269KO2.

3. Ratings and characteristics
Refer to the attached sheet, page 5 to 7.

4. Reliability
Refer to the attached sheet, page 8.

5. Incoming inspection
Refer to the attached sheet, page 9.

6. Supplement

6.1 Isolation voltage shall be measured in the following method.
(1) Short between anode and cathode on the primary side and between

collector and emitter on the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.

6.2 Packaging specifications

Refer to the attached sheet, page 10 to 12.

SHARP CORPORATION

6.3 Business dealing name (“0” mark indicates business dealing name of ordered product)

ED-97136

MODEL No. PAGE

1 September 8, 1997

PC357NT 2/ 12

Rank mark

PC357NIT 1 A

I

PC357N2T 1 B

I

PC357N3T 1 C

I

PC357N4T 1 D

I

PC357N5T 1 A or B

I

PC357N6T
PC357N7T

PC357N8T
PC357N9T
PC357NOT

0

6.4 The following selection shall be made as to the collector-emitter
breakdown voltage (BVceo) in parameter 3.2.

(Applied to lot No. “J5” [May 19971 or later]

PC357NT

A, B, C, D or no mark

B or C
C or D

A, B or C

B, CorD

A, B, C or D

4.0 to 8.0

I

6.5 to 13

I

10 to20

I

15to30

I

4.0 to 13

I

6.5 to 20
10to30

4.0 to 20

6.5 to 30

4.0 to 30

2.5 to 30

Ic blA)

Test
conditions

I

I

1,=5mA

I

I

I

vc,=5v

Ta=25%

Parameter Symbol Conditions MIN. TYP. MAX. unit

Collector-emitter
breakdown voltage Ir=O

6.5 This Model is approved by UL.
Approved Model No. : PC357
UL iile No. : E64380

6.6 This product is not designed against irradiation.
This product is assembled with electrical input and output.

This product incorporates non-coherent light emitting diode.

BVCEO

Ic=O. 1mA 70 - -

V

SHARP CORPORATION

6.7 ODS materials
This device. component shall not contain the following materials.

Also, the following materials shall not be used in the production process
for this device * component.

Materials for ODS :

6.8 Brominated flame retardants
Specific brominated flame retardants such as the PBBO, and PBB, are not used

in this device component at all.

7. Notes
Refer to the attached sheet- l-l, 2.

CFC!,, Halon, Carbon tetrachloride,

1.1.1 -Trichloroethane (Methylchloroform)

SHARP CORPORFlTl ON

<

CD (3

k 2.54kO.254

3. 6+0. 3

*

Date code ‘1

ED-97136

MODEL No.

PC357NT

Pin Nos. and

connection diagram

internal

1 September 8, 1997

PAGE

4/

12

Epoxy resin

0

Anode

0

Cathode

\ Rank mark
Factory identification mark l 2

22

.

z

cx

.-

d

;

@

Collector

3

Emitter

+I

I I

*l) 2-digit number shall be marked according to DIN standard.

*2) Factory identification mark shall be or shall not be marked.

*31 Marking is laser marking

Product mass : Approx. 0.1 Og

I

UNIT: l/l mm