Page 1
Quick Guide
PORTABLE MINIDISC RECORDER
MODEL
MD-MT877H
Quick Setup Guide
Follow the setup procedure (1-3)
before you use this unit.
Quick Operation Guide
Explains basic recording and playback
procedures.
Refer to the operation manual for details.
If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www. sharp.co.uk/support.
Customers without internet access may telephone
08705 274277 during office hours (or (01) 676 0648
if telephoning from Ireland).
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
TINSE0341AWZZ
A0011.TO
Page 2
1
Insert a MiniDisc
44
222
1
1 Slide the OPEN lever to re-
lease the compartment door.
2 Lift it up the compartment.
Insert according to
the direction arrow.
33
3 Insert a MiniDisc as shown.
4 Close the compartment door .
When you record on a MiniDisc,
check that the erase prevention tab
is set to the “recordable” position.
Recordable
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Recording
prevented
Page 3
2
Connect the AC adaptor
RELEASE
LOCK
AC 230-240V,
50/60 Hz
To the DC IN
5V socket.
1 Move the Charge/Operation
switch to CHARGE mode (RELEASE).
2 Insert the portable MD into
the battery charger.
Before using the unit with a rechargeable battery, the battery has to be charged.
Refer to “Using with the rechargeable battery”, page 12 (operation manual) for
details.
Caution:
● Before setting the main unit to the battery charger, make sure the battery charger
is in CHARGE mode (RELEASE). If you insert the main unit by force whilst in
OPERA TION mode (LOCK), the hook for fixing the main unit may break.
● If the Charge/Operation switch is not set to OPERATION mode, no operation is
possible. Refer to “How to use the Charge/Operation switch”, page 11 (operation
manual) for details.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Insert securely, all the way in.
3 Move the Charge/Operation
switch to OPERATION mode
(LOCK).
4 Plug the AC adaptor.
To wall socket.
Page 4
3
Connection
OPTICAL/
LINE IN
White: To Left
Red: To Right
AUDIO OUT
LEFTRIGHT
NOTE:
Refer to page 19 (operation manual) for connecting the unit to a stereo system
with “DIGITAL OUT” or “OPTICAL OUT” sockets.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
T o a stereo system with “AUDIO OUT” or “LINE
OUT” sockets. (See left. Analogue connection)
Note:
● If the audio system has only one pair of socket then
they are usually input only and recording via this connection is not possible.
Page 5
Preparation for use
The unit does not work
if the • ■ / –HOLD button is set to HOLD.
Press the • ■ / –HOLD button for 2 seconds or more.
Hold
Released
Operation mode
For operations
Move it to operation mode when playing back or
recording.
CAUTION:
It is not recommendable to put the
MiniDisc into a rear pocket, as this
may damage the product when sitting.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Page 6
Recording
Check that the unit is connected to the stereo system.
1 Press the REC button.
●Record pause mode is entered.
●The REC button does not light.
2 Begin playback on the stereo system connected to this unit.
●To enable the record level to be set.
3 Press the
●
Adjust the recording level so that the maximum sound volume from the
source makes the reading swing somewhere between –4 dB and 0 dB.
●
This unit can adjust the digital recording level just the same as the analogue recording.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
55
5 or
55
44
4 button
44
Level meter indicator
to adjust the recording level.
0dB
4dB
Continued to the next page
Page 7
Recording: continued
4 Press the P AUSE button on the stereo system to enter the play-
back pause mode at the point you wish to start recording.
●
Here you can select the track to be recorded.
5 Press the MODE button repeatedly to select recording mode.
5 Press the
6
Begin playback on the stereo system, the output will be recorded.
To stop recording
Press the • ■ / :OFF button.
● When recording stops, “TOC” ap-
pears (Table Of Contents). Whilst
“TOC” appears the MiniDisc recorded contents have not yet been
updated.
● To prevent the new recording from
being lost it is not possible to remove the MiniDisc whilst “TOC” is
displayed.
T o update the recorded contents
of the MiniDisc
Press the • ■ / :OFF button whilst
in the stop mode.
● The power turns off after recorded
contents have been updated on the
MiniDisc.
0606
06 button to start the MiniDisc unit recording.
0606
About the TOC
After any recording or editing function
“TOC” (T able Of Contents) is displayed.
TOC display
T o finalise the recording or editing function, press the •
ing this process “TOC” will flash and
“TOC EDIT!” will be displayed.
During any recording or editing function the MiniDisc unit Lid is locked, the
MiniDisc can not be removed until the
process is finalised.
Warning
●If the power is removed (Battery/AC
adapter) whilst “TOC” is displayed
the MiniDisc unit lid will remain
locked until the battery/main power
is restored and the unit is turned on.
Your new recordings or edited
changes will be lost and your
MiniDisc may become unusable.
■ / :OFF button. Dur-
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Page 8
Playing
1 Insert the earphones plug firmly into the earphones socket on
the remote control unit.
2 Plug the remote control into the socket on the unit.
3 Insert a MiniDisc.
4 Press the
● Playback starts automatically with a playback only MiniDisc or a MiniDisc
which is protected against accidental erasure (Auto-play function).
To stop playback
Press the • ■ / :OFF button (Remote
control: press the ■ button).
● If the unit is not operated for at least
2 minutes whilst in the stop mode, the
power will shut off automatically.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
06 06
06 button.
06 06
Loading...