In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.
LC-52SE941U-G
OUTLINE
This model is based on the LC-46/52SE941U and is changed some parts. This Service Manual covers the modifications alone. For the other points, refer to the LC-46SE941U (No. S18D1LC46SE94) and LC-52SE941U (No.
SX7A6LC65SE94) Service Manual.
• The stand (ST52SE94) and speakers (SP46SE94) for Model LC-46SE941U-R/G are separately sold.
• The stand (ST52SE94) and speakers (SP52SE94) for Model LC-52SE941U-R/G are separately sold.
CONTENTS
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE.................................................................... i
LIST OF CHANGED PARTS
(LC-46SE941U-R/G) .................................................. i
LIST OF CHANGED PARTS
(LC-52SE941U-R/G) ................................................ iv
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY
PRECAUTION.......................................................... vi
KEY ROM................................................................. ix
Parts Guide
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
Page 2
LC-46/52SE941U-R/G
i
LC-46/52SE941U-R/G
Service Manual
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE
This model is based on the LC-46/52SE941U and is changed some parts. This Service Manual covers the modifications alone. For the other points,
refer to the LC-46SE941U (No. S18D1LC46SE94) and LC-52SE941U (No. SX7A6LC65SE94) Service Manual.
• The stand (ST52SE94) and speakers (SP46SE94) for Model LC-46SE941U-R/G are separately sold.
• The stand (ST52SE94) and speakers (SP52SE94) for Model LC-52SE941U-R/G are separately sold.
LIST OF CHANGED PARTS (LC-46SE941U-R/G)
Ref. No.Description
LC-46SE941U
(No. S18D1LC46SE94)
LC-46SE941U-R/G
(No. S48J2LC46SE94)
Note
PRINTED WIRING BOARD ASSEMBLIES
SPEAKER-L UnitDUNTKD744WE01←Some parts changed
SPEAKER-R UnitDUNTKD745WE01←Some parts changed
TERMINAL UnitDUNTKE208FM02←Some parts changed
R/C, LED UnitDUNTKE264FM11←Some parts changed
KEY UnitDUNTKE266FM02←—
MAIN UnitDUNTKE421FM02DKEYME421FM04Some parts changed
SIDE UnitDUNTKE488FM04←—
POWER UnitRDENCA235WJQZ←—
AC INLET UnitRUNTKA317WJQZ←—
LCD PANEL
LCD Panel Module UnitR1LK460D3LZ70Z←—
SPEAKER-L Unit
J201JackQTANAA008WJZZQTANAA013WJZZChange
SPEAKER-R Unit
J202JackQTANAA008WJZZQTANAA013WJZZChange
TERMINAL Unit
C539CapacitorVCKYCY1EF104ZY—Delete
C543CapacitorVCKYCY1EF104ZY—Delete
C547CapacitorVCAAPF1CJ396MY—Delete
R/C, LED Unit
Q102TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q103TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q104TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q106TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q107TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
MAIN Unit
IC1604ICVHiSii9185+-1QVHiSii9185A-1QChange
R1302ResistorVRK-SB1FF223JYVRS-CG1JF223JYChange
R1413ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8151ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8152ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8153ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8154ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8155ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8156ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8157ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8158ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8159ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8160ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8161ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
R8162ResistorVRK-SB1FF220JYVRS-CG1JF220JYChange
CABINET AND MECHANICAL PARTS
Please refer to a Parts list
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list
Ref. No.Description
LC-46SE941U
(No. S18D1LC46SE94)
LC-46SE941U-R/G
(No. S48J2LC46SE94)
Note
Page 5
LC-46/52SE941U-R/G
iv
LIST OF CHANGED PARTS (LC-52SE941U-R/G)
Ref. No.Description
LC-52SE941U
(No. SX7A6LC65SE94)
LC-52SE941U-R/G
(No. S48J2LC46SE94)
Note
PRINTED WIRING BOARD ASSEMBLIES
SPEAKER-L UnitDUNTKD744WE01←Some parts changed
SPEAKER-R UnitDUNTKD745WE01←Some parts changed
TERMINAL UnitDUNTKE208FM02←Some parts changed
R/C, LED UnitDUNTKE264FM11←Some parts changed
KEY UnitDUNTKE266FM02←—
MAIN UnitDUNTKE421FM01DKEYME421FM03Some parts changed
SIDE UnitDUNTKE488FM04←—
POWER UnitRDENCA235WJQZ←—
AC INLET UnitRUNTKA317WJQZ←—
LCD PANEL
LCD Panel Module UnitR1LK520D3LZ70Z←—
SPEAKER-L Unit
J201JackQTANAA008WJZZQTANAA013WJZZChange
SPEAKER-R Unit
J202JackQTANAA008WJZZQTANAA013WJZZChange
TERMINAL Unit
C539CapacitorVCKYCY1EF104ZY—Delete
C543CapacitorVCKYCY1EF104ZY—Delete
C547CapacitorVCAAPF1CJ396MY—Delete
R/C, LED Unit
Q102TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q103TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q104TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q106TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
Q107TransistorVS2SC3928AR-1YVSKTC3875SG-1YChange
CABINET AND MECHANICAL PARTS
Please refer to a Parts list
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list
Ref. No.Description
LC-52SE941U
(No. SX7A6LC65SE94)
LC-52SE941U-R/G
(No. S48J2LC46SE94)
Note
Page 7
LC-46/52SE941U-R/G
vi
LC-46/52SE941U-R/G
Service Manual
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 110-240 volt 50/60Hz AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by "" and shaded areas in the Replacement Parts List
and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
CAUTION: FOR CONTI N U E D PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
F7000 (250V 6.3A)
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15µF
TEST PROBE
Page 8
LC-46/52SE941U-R/G
vii
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
De nombreuses pièces, électriques et mécaniques, dans les téléviseur ACL présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension, puissance,
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque "" et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
Pour assurer la protection, ces pièces doivent être identiques à celles
utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
les mêmes caractéristiques que les pièces recommandées par l'usine,
indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est dangereux.
Débrancher le récepteur avant toute réparation.
Inspecter tous les faisceaux de câbles pour s'assurer que les fils
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.
Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc.
S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une prise de courant de 110-240V 50/60Hz. (Ne pas utiliser de transformateur
d'isolation pour cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ
10 watts en parallèle avec un condensateur de 0.15µF en série
avec toutes les pièces métalliques exposées du coffret et une terre
connue comme une conduite électrique ou une prise de terre
branchée à la terre.
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour
mesurer la chute de tension en travers de la résistance.
Toucher avec la sonde d'essai les pièces métalliques exposées qui
présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (correspondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes.
DVM
ECHELLE CA
1.5k ohm
10W
0.15
µ
F
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
AVIS POUR LA SECURITE
F7000 (250V 6.3A)
Page 9
LC-46/52SE941U-R/G
viii
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper.Indicates lead-free solder of tin, silver and copper.
The HDCP-KEY ROM shall be protected and managed for its information inside. In servicing this ROM, therefore, take the following information protection/management measures.
1) When disposing of the component parts and PWBs, destruct the IC itself in a proper way.
(For repairing or replacing the component parts and PWBs as well as clearing those in stock)
2) In storing the component parts, protect and manage them against theft and disclosure.
(For storing the service parts, service units, etc.)
Applied part: HDCP-KEY ROM
IC8451 RH-IXC318WJQZY (updated ROM)
Page 11
PartsGuide
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
LC-46/52SE941U-R/G
PARTS GUIDE
No. S48J2LC46SE94
LC-46SE941U-R
LC-46SE941U-G
LC-52SE941U-R
MODELS
CONTENTS
LC-52SE941U-G
[1]PRINTED WIRING BOARD ASSEMBLIES
[2]LCD PANEL (NOTE: THE PARTS HERE
SHOWN ARE SUPPLIED AS AN ASSEMBLY
BUT NOT INDEPENDENTLY.)
[3]DUNTKD744WE01 (SPEAKER-L Unit)
[4]DUNTKD745WE01 (SPEAKER-R Unit)
[5]DUNTKE264FM11 (R/C, LED Unit)
[6]DKEYME421FM04 (LC-46SE941U-R/G)
DKEYME421FM03 (LC-52SE941U-R/G)
(MAIN Unit)
[7]NOTE (Temperature-proof cover)
[8]CABINET AND MECHANICAL PARTS
(LC-46SE941U-R/G)
[9]CABINET AND MECHANICAL PARTS
(LC-52SE941U-R/G)
[10]SUPPLIED ACCESSORIES
[11]PACKING PARTS (NOT REPLACEMENT ITEM)
[12]SERVICE JIG (USE FOR SERVICING)
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Page 12
LC-46/52SE941U-R/G
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES
NDUNTKD744WE01AENXSPEAKER-L Unit
NDUNTKD745WE01AENXSPEAKER-R Unit
NDUNTKE208FM02BHNXTERMINAL Unit
NDUNTKE264FM11AQNXR/C, LED Unit
NDUNTKE266FM02AGXKEY Unit
NDKEYME421FM04CCNXMAIN Unit (BQC) (LC-46SE941U-R/G)
NDKEYME421FM03CCNXMAIN Unit (BQC) (LC-52SE941U-R/G)
NDUNTKE488FM04BBNXSIDE Unit
NRDENCA235WJQZBRXPOWER Unit
NRUNTKA317WJQZAWXAC INLET Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-
DENTLY.)
NR1LK460D3LZ70ZFFNJ46" LCD Panel Module Unit (LC-46SE941U-R/G)
NR1LK520D3LZ70ZGQNJ52" LCD Panel Module Unit (LC-52SE941U-R/G)
R8213VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8214VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8228VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8230VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8231VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8232VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8233VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8234VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8235VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8236VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8237VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8238VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8239VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8240VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8241VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8242VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8243VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8244VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8255VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8257VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8258VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8259VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8260VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8261VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8262VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8263VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8264VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8265VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8266VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
R8268VRS-CG1JF680JYAAXResistor, 68 1/16W Metal Oxide
R8269VRS-CG1JF220JYAAXResistor, 22 1/16W Metal Oxide
NPSPAZB774WJKZAHXCool Sheet (LC-46SE941U-R/G)
3
Page 14
LC-46/52SE941U-R/G
[7] NOTE (Temperature-proof cover)
LC-46SE941U-R/G
Added covers parts
ԘCover parts code: PSPAGA386WJ00Q'ty 4
ԙCover parts code: PSPAKA237WJ00Q'ty 1
1
111
2
LC-52SE941U-R/G
1111
2
Attention
Please peel off the covers when you remove Rear Cabinet.
And please use the NEW cover when you install Rear Cabinet.
(When using the cover again, keep in mind the decrease in the adhesive power of the cover.
The purpose of using the NEW cover is to prevent the cover from peeling off.)
S1SPAKCD916WJZZ-N-Packing Case (Bottom) (LC-46SE941U-R/G)
S1SPAKCD913WJZZ-N-Packing Case (Bottom) (LC-52SE941U-R/G)
S2SPAKCE169WJZZ--Packing Case (Main) (LC-46SE941U-R/G)
S2SPAKCE168WJZZ--Packing Case (Main) (LC-52SE941U-R/G)
S3SPAKPA999WJZZ--Wrapping Paper (LC-46SE941U-R/G)
S3SPAKPA992WJZZ--Wrapping Paper (LC-52SE941U-R/G)
S4SPAKXB757WJZZ--Packing Add. (LC-46SE941U-R/G)
S4SPAKXB756WJZZ--Packing Add. (LC-52SE941U-R/G)
S5SSAKA0101GJZZ--Polyethylene Bag
S6SSAKAA032WJZZ--Polyethylene Bag
S7TLABKA009WJZZ--No. Label
S8TLABMD067WJ3A-N-P Label (LC-46SE941U-R)
S8TLABMD068WJ3A-N-P Label (LC-46SE941U-G)
S8TLABMD100WJ3A-N-P Label (LC-52SE941U-R)
S8TLABMD101WJ3A-N-P Label (LC-52SE941U-G)
[12] SERVICE JIG (USE FOR SERVICING)
NQCNW-C222WJQZAWJConnecting Cord (80pin L=1000mm), x2
NLCD CONTROL to LCD Panel Unit
NQCNW-E068WJQZASJConnecting Cord (6pin L=1000mm)
NTERMINAL to POWER Unit (PE)
NQCNW-G186WJQZBLJConnecting Cord (41pin L=600mm)
NMAIN to LCD CONTROL Unit (LW)
NQCNW-G400WJQZAVJConnecting Cord (12pin L=1000mm)
NMAIN to POWER Unit (PD)
NQCNW-H015WJQZAVNJConnecting Cord (9-12-4pin L=1000mm)
NLCD CONTROL to MAIN to POWER Unit (LP/PL)
NQCNW-H016WJQZAQNJConnecting Cord (5-9pin L=1000mm)
NMAIN to INVERTER Unit (LB)
NQCNW-H019WJQZAMNJConnecting Cord (3pin L=1000mm), x2
NPOWER to INVERTER Unit (LA-1/LA-2)
NQPWBHE372WJQZBEJConnecting Cord (21pin L=1000mm)
NMAIN to SIDE Unit (HM)
AV Systems Group
CS Promotion Center
Yaita, Tochigi 329-2193, Japan
Jun. 2008
TQ2535-S MI. KD
COPYRIGHT2008 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
LC-46/52SE941U-R/G
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.