Sharp LC-32B20E, LC-32B20S, LC-32G20E, LC-32G20S, LC-37B20E Operating Manual
...
LC-32B20E
LC-32B20S
LC-32G20E
LC-32G20S
LC-37B20E
LC-37B20S
LC-37G20E
LC-37G20S
ENGLISHDEUTSCHFRANÇAISITALIANO
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
NEDERLANDS
ESPAÑOL
SPECIAL NOTE FOR USERS IN THE U.K.
)5)
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse cover fi tted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fi t an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fi tted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
OPERATION MANUAL
ENGLISH
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the
actual operations.
• The examples used throughout this manual are based on the LC-37B20E/LC-37G20E model.
Contents
ENGLISH
Contents .........................................................................................1
Introduction ....................................................................................2
Dear SHARP customer .............................................................2
Important Safety Precautions ....................................................2
Trademarks ...............................................................................2
Remote control unit...................................................................3
TV (Front view) ..........................................................................4
TV (Rear view) ...........................................................................4
Preparation ....................................................................................5
Supplied accessories ................................................................5
Attaching the stand unit ............................................................5
Inserting the batteries ................................................................6
Using the remote control unit ....................................................6
Cautions regarding the remote control unit ...........................6
Quick guide ....................................................................................7
Initial installation overview ..........................................................7
Before turning on the power......................................................8
Bundling the cables .............................................................8
Initial auto installation ................................................................9
Checking signal strength and channel strength ....................9
Watching TV .................................................................................10
Daily operation ........................................................................10
Switching on/off .................................................................10
Switching between analogue and digital broadcasts ..........10
Changing channels ............................................................10
Selecting external video source ..........................................10
Selecting Sound mode ......................................................10
EPG (Electronic Programme Guide) .........................................11
EPG Overview .........................................................................11
Useful settings for using EPG ..................................................11
Selecting a programme using EPG..........................................12
Timer recording using EPG .....................................................13
Cancelling the timer recording .................................................13
Teletext ...................................................................................14
Using the MHEG5 application (UK only) ..................................14
Connecting external devices ......................................................15
Introduction to connections .....................................................15
HDMI connection ...............................................................16
Component connection .....................................................16
S-VIDEO/VIDEO connection ..............................................16
SCART connection ............................................................17
Controlling devices with SCART using AV Link ..................17
Speaker/amplifier connection .............................................18
Inserting a CA Card .................................................................19
AQUOS LINK ................................................................................20
Controlling HDMI devices using AQUOS LINK .........................20
AQUOS LINK connection ........................................................21
AQUOS LINK Setup ................................................................21
Operating an AQUOS LINK device ..........................................22
Menu operation............................................................................23
What is the Menu? ..................................................................23
Common operations ..........................................................23
Basic adjustment .........................................................................24
Picture Settings .......................................................................24
AV Mode ............................................................................25
Audio Settings ........................................................................25
Power Save Settings ...............................................................25
Channel Settings .....................................................................26
Auto Installation .................................................................26
Digital channel settings ......................................................26
Analogue channel settings .................................................27
Password/Parental lock settings ........................................28
Language Settings (language, subtitle, multi audio) .................28
Useful Viewing functions ............................................................29
Selecting the WSS picture size automatically .....................29
Selecting the WSS picture size manually ............................29
Selecting the picture size manually .....................................29
Selecting the recording picture size manually .....................30
Selecting the HDMI picture size automatically ....................30
Other Picture and audio settings .............................................30
Adjusting image position ....................................................30
Reducing noise on the screen ............................................30
Automatic volume adjustment ............................................30
Clear Voice ........................................................................30
Audio Only .........................................................................30
Display Settings ......................................................................31
Channel display .................................................................31
Time and Title display ........................................................31
Other useful features ..................................................................32
Setting when using external devices .......................................32
Input source settings .........................................................32
Skipping specified input .....................................................32
Colour system settings ......................................................32
Additional features ..................................................................32
Connecting a PC ..........................................................................33
Connecting a PC ....................................................................33
Displaying a PC image on the screen ......................................33
Selecting the picture size ...................................................33
Adjusting the PC image automatically ................................34
Adjusting the PC image manually .......................................34
Selecting input resolution ........................................................34
RS-232C port specifications ...................................................35
PC compatibility chart .............................................................36
RS-232C command list...........................................................36
Appendix ......................................................................................37
Troubleshooting ......................................................................37
Updating your TV via DVB-T ...................................................38
Reset ......................................................................................38
Identification............................................................................38
Specifications .........................................................................39
Optional accessory .................................................................39
End of life disposal ..................................................................40
1
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
Introduction
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub,
swimming pool and in a wet basement.
• Do not place vases or any other water-filled containers on this product.
The water may spill onto the product causing fire or electric shock.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause the
product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When
mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting
hardware recommended by the manufacturer.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops,
excessive force and uneven floor surface can cause the product to fall from the cart.
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or
block these vents and openings since insufficient ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they
can block ventilation openings. This product is not designed for built-in installation; do not place the
product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is
dropped or impact applied. If the LCD panel is broken, be careful not to be injured by broken glass.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
• To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• There is power consumption always if main plug is connected.
• Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high
voltage and other dangerous conditions. Request a qualified person to perform servicing.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a
fixed point of blue, green or red.
This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two
people holding it with two hands — one hand on each side of the TV.
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of troublefree operation of your product, please read the Important Safety Precautions carefully before using this product.
• Manufactured under license from Dolby Laboratories.
• “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• The “HD ready 1080P” Logo is a trademark of EICTA.
• The DVB logo is the registered trademark of the Digital Video Broadcasting - DVB - project.
Trademarks
Important Safety Precautions
Dear SHARP customer
• TruSurround XT, SRS and h symbol are trademarks of SRS Labs, Inc.
2
Introduction
15
16
17
18
19
20
21
22
23
24
25
4
3
2
5
6
7
8
9
10
11
12
13
14
1
1 B (Standby/On) (Page 10)
2 Buttons for useful operations
m (Teletext)
ATV: Display analogue teletext. (Page 14)
DTV: Select MHEG-5 and teletext for DTV.
(Page 14)
k (Reveal hidden Teletext) (Page 14)
[ (Subtitle)
ATV/DTV/External: Switch subtitle
languages on/off. (Pages 14 and 28)
3 (Freeze/Hold)
Press to freeze a moving image on the
screen.
TELETEXT: Stop updating Teletext pages
automatically or release the hold mode.
1 (Subpage) (Page14)
v (Top/Bottom/Full)
Set the area of magnification in teletext
mode. (Page 14)
3 0 - 9 numeric buttons
Set the channel.
Enter desired numbers.
Set the page in teletext mode.
4
A (Flashback)
Press to return to the previous image in
normal viewing mode.
5 DTV
Press to access DTV mode.
6 ATV
Press to access conventional analogue TV
mode.
7 2
(Sound mode)
Select the sound multiplex mode. (Page 10)
8 i (k/l) (Volume)
Increase/decrease TV volume.
9
e (Mute)
TV sound on/off
10
f (WIDE MODE)
Select the wide mode. (Pages 29 and 33)
11 AV MODE
Select a video setting. (Page 25)
12
a/b/c/d (Cursor)
Select a desired item on the setting
screen.
OK
Execute a command within the menu
screen.
ATV/DTV: Display the programme list
when no other menu screen is running.
13 END
Exit the menu screen.
14 R/G/Y/B (Colour) buttons
On the menu screen, the coloured buttons
are correspondingly used to select the
coloured items on the screen. (e.g. EPG,
MHEG-5, TELETEXT)
15
b (INPUT SOURCE)
Select an input source. (TV, EXT1, EXT2,
EXT3, EXT4, EXT5, EXT6, EXT7, EXT8)
(Page 10)
16 EPG
DTV: Display the EPG screen. (Pages 11
- 13)
17 RADIO
DTV: Switch between Radio and Data
mode.
• When only data broadcasting (no radio
broadcasting) is transmitted by DVB,
the radio broadcasting will be skipped.
18 P. INFO
Press to display programme information
which is transmitted through digital video
broadcasting in the upper left corner of
the screen. (DTV only)
19 P (
r/s)
Select the TV channel.
20
p (Display information)
Press to display the station information
(channel number, signal, etc.) in the upper
right corner of the screen. (Page 31)
21 SLEEP
Press to schedule a time for the TV to
automatically standby. (Page 26)
22 MENU
ATV/DTV: Menu screen on/off.
23
6 (Return)
Return to the previous menu screen.
24 ACTION (Action Mode)
This key does not work on this model.
25 AQUOS LINK buttons
If external equipment such as a AQUOS
BD Player is connected via HDMI cables
and is AQUOS LINK compatible, you can
use these AQUOS LINK buttons. See
pages 20 and 22 for details.
Remote control unit
3
Introduction
16
12
13
14
7
8
9
10
11
1
2
3
4
5
6
15
12 EXT 3 terminals
13 Headphones
14 SERVICE socket
15 COMMON INTERFACE slot
16 AC INPUT terminal
7 EXT 6 (HDMI/AUDIO) terminals
8 RS-232C terminal
9 EXT 8 (COMPONENT/AUDIO) terminals
10 EXT 2 (RGB) terminal
11 EXT 1 (RGB) terminal
1 EXT 4 (HDMI) terminal
2 EXT 5 (HDMI) terminal
3 EXT 7 (ANALOGUE RGB/AUDIO) terminals
4 DIGITAL AUDIO OUTPUT terminal
5 OUTPUT (AUDIO) terminals
6 Antenna terminal
TV (Front view)
TV (Rear view)
4
Remote control sensor
OPC sensor
OPC indicator
SLEEP indicator
B (Standby/On)
indicator
MENU button
a (Power) button
i
(k/l) Volume buttons
P (r/s)
Programme [channel] buttons
b (INPUT SOURCE) button
Preparation
Supplied accessories
Attaching the stand unit
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1 Insert the stand into the openings on the
bottom of the TV. (Hold the stand so it will
not drop from the edge of the base area.)
2 Insert and tighten the 4 screws into the
4 holes on the rear of the TV.
3
1
2
Confirm that there are 10 screws with the stand
unit.
1
Attach the supporting post for the stand unit
onto the base using the 6 screws with the screw
driver (supplied) as shown.
2
NOTE
• To detach the stand unit, perform the steps in reverse
order.
5
Remote control unit
(g1)
AC cord (g1) Stand unit (g1)
Cable clamp (g1)
Pages 3 and 6 Page 5
Page 8Page 8
• Operation manual (This publication)
• “AAA” size battery (
g2) ... Page 6
Soft
cushion
Preparation
Inserting the batteries
Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Open the battery cover.
Insert two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding
to the (k) and (l) indications in the battery
compartment.
Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
businesses.
1
2
3
Using the remote control unit
Use the remote control unit by pointing it
towards the remote control sensor. Objects
between the remote control unit and sensor
may prevent proper operation.
30° 30°
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place in an area
with high humidity.
• Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the unit.
• The remote control unit may not work properly if the remote control sensor of the TV is
under direct sunlight or strong lighting. In such case, change the angle of the lighting or
TV, or operate the remote control unit closer to the remote control sensor.
6
5 m
Remote control sensor
Quick guide
Initial installation overview
Follow the below steps one by one when using the TV for the first time. Some steps may not be necessary
depending on your TV installation and connection.
Preparation
Connect antenna cable to the
antenna terminal. (Page 8)
If necessary, insert CA card
into the CI slot to watch
scrambled broadcasts.
(Pages 8 and 19)
Connect the AC cord to the
TV. (Page 8)
Turn on the TV power with a.
(Page 10)
Run the initial auto installation.
(Page 9)
4 Language setting
English
Italiano
Svenska
4 Country setting
Austria A B/G
Finland
FIN
B/G
Greece GR B/G
4 Channel search setting
Analogue SearchDigital Search
Congratulations!
Now you can watch TV.
If necessary, adjust the
antenna to attain maximum
signal reception. (Page 9)
Connect external
devices such as a
DVD as instructed.
(Pages 15 - 17)
Connect external
audio devices such
as speakers/amplifier
as instructed.
(Pages 15 and 18)
1
Power on and
run the auto
installation
2
Watch TV
3
Start searching
channels
Connect
external devices
7
Before turning on the power
Quick guide
Supplying power to the antenna
You must supply power to the antenna in order to
receive digitally/terrestrially broadcast stations after
connecting the antenna cable to the antenna input
terminal on the back of your TV.
1. Press MENU and the menu screen displays.
2. Press c/d to select “Setup”.
3. Press a/b to select “Antenna Setup-DIGITAL”,
and then press OK.
4. Press a/b to select “Supply Voltage”, and then
press OK.
5. Press c/d to select “On”, and then press OK.
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket and attachment available from SHARP.
(Page 39) The use of other wall mount brackets may result in an unstable installation and may cause serious
injuries.
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
• You can ask a qualified service personnel about using an optional bracket and attachment to mount the TV to the wall.
• To use this TV mounted on a wall, first remove the adhesive tape at the 2 locations on the rear of the TV, and then use the
screws supplied with the wall mount bracket to secure the bracket to the rear of the TV.
• When you mount the TV on the wall, you should attach the supporting post.
Bundling the cables
8
1. Carefully insert the
CI Module in the CI slot
with the contact side
forward.
Cable clamp
Bundle the
cables with the
clamp.
AC cord
Place the TV close to the
AC outlet, and keep the
power plug within reach.
Standard DIN45325
plug (IEC 169-2)
75 q coaxial cable
2. The logo on the CI
Module must be facing
forward from the rear of
the TV.
Quick guide
Initial auto installation
When the TV powers on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
Checking signal strength and channel strength
If you install a DVB-T antenna for the first time or
relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
Press
MENU and the menu screen displays.
Press
c/d to select “Setup”.
Press
a/b to select “Antenna Setup-DIGITAL”,
and then press OK.
E
Checking signal strength
Press a/b to select “Signal Strength”.
Signal Strength
Supply Voltage
Channel Strength
Signal Strength
Quality
Current Max.0
CH No. 21
0
Current Max.0 0
E
Checking channel strength
Press a/b to select “Channel strength”, and
then press OK.
• You can input a specified frequency band using 0 - 9
numeric buttons.
Signal Strength
Supply Voltage
Channel Strength
Signal Strength
Quality
Current Max.0
CH No. 21
0
Current Max.0 0
2 6 5 . 2
MHz
Position and align the antenna so that the
maximum possible values for “Signal Strength”
and “Quality” are obtained.
NOTE
• The values of “Signal Strength” and “Quality” indicate when
to check the appropriate alignment of the antenna.
1
2
3
4
Press a on the TV.
• The initial auto installation wizard appears.
Setting the on-screen display language
English
Italiano
Svenska
Setting the country (Location of TV set screen)
Austria A B/G
Finland
FIN
B/G
Greece GR B/G
• The Location of TV set screen only appears during
the first installation.
Starting channel search
Analogue SearchDigital Search
• If you want to search for more broadcasts, execute
“Auto Installation” again from the Setup menu.
1
2
3
4
Confirm the following before turning on
the power
E Is the antenna cable connected?
E Is the AC cord plugged in?
Press a/b/c/d to select the desired language,
and then press OK.
Press a/b/c/d to select your country or area,
and then press OK.
Press c/d to select “Digital Search” or “Analogue
Search”, and then press OK.
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
• To abort the initial auto installation in progress, press
END
.
NOTE
• If you turn off the power on the TV after performing step 4,
the initial auto installation wizard does not appear. The auto
installation function allows you to execute the installation
again from the Setup menu. (Page 26)
• The initial auto installation wizard will go off if you leave
the TV unattended for 30 minutes before searching for
channels in step 5.
5
9
Watching TV
TV indicator status
B indicator
Status
Off Power off
Green Power on
Red Standby
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• A small amount of electric power is still consumed even
when a is turned off.
Changing channels
With Pr/Ps: With 0 - 9:
Switching between analogue and digital broadcasts
Selecting external video source
Once the connection is made, press
b to display the INPUT SOURCE
screen, and then press a/b to switch
over to the appropriate external source
with OK.
INPUT SOURCE
TV
EXT1
EXT2
EXT3
EXT4
EXT5
INPUT SOURCE
TV
EXT1
EXT2
EXT3
EXT4
EXT5
Selecting Sound mode
DTV mode:
E
If multi sound modes are received, each
time you press 2 the mode switches as
follows.
Audio (ENG) : STEREO
L/R L R LR
Audio (ENG) : CH A
CH A CH B CH AB
Audio (ENG) : MONO
E
Press c/d to select L or R sound when
the STEREO or DUAL MONO screen is
displayed.
Audio (ENG) : STEREO
L/R L R LR
NOTE
• The sound mode OSD disappears in 6 seconds.
• Selectable items vary depending on the received
broadcasts.
ATV mode:
Each time you press 2, the mode switches as
illustrated in the following tables.
NICAM TV broadcasts selection
Signal Selectable items
Stereo
NICAM STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B, NICAM CH AB,
MONO
Monaural
NICAM MONO, MONO
A2 TV broadcasts selection
Signal Selectable items
Stereo
STEREO, MONO
Bilingual
CH A, CH B, CH AB
Monaural
MONO
NOTE
• When no signal is input, the sound mode will display
“MONO”.
• However, please bear in mind
that EPG data (electronic
programme guide) will be
lost, and programmed
timer recordings will not be
performed by the TV.
Daily operation
Switching on/off
Turning on/off the power
Press a on the TV.
Switch it off by pressing a on the TV.
E
Watching analogue
broadcasts
E
Watching digital
broadcasts
Standby mode
E
To standby mode
If the TV set is switched on, you can switch it to
standby by pressing B on the remote control.
E
Switching on from standby
From standby, press B on the remote control.
10
Watching TV
EPG (Electronic Programme Guide)
EPG (Electronic Programme Guide) is a programme list that is displayed on the screen. With the EPG, you can
check the schedule of DTV/RADIO/DATA, view detailed information about them, tune to an event currently on-air
and set a timer for future events.
EPG Overview
E
Basic functions
E
Useful functions
E Select a programme using EPG (Page 12)
E Check programme information (Page 12)
E Search for a programme by category (Page 12)
E Search for a programme by date and time
(Page 12)
E Timer recoding using EPG (Page 13)
Useful settings for using EPG
Press MENU to display the menu screen.
Press
c/d to select “Digital Setup”.
MENU
[
Digital Setup
...
EPG Setup
]
Digital Setup Information
REC Picture Size
Download Setup
EPG Setup
Subtitle
CI Menu
[Yes]
[16:9 TV]
Press a/b to select “EPG Setup”, and then
press OK.
Yes No
EPG Setup
Display Range Setup
Genre Icon Setup
Press c/d to select “Yes” or “No”, and then
press OK.
1
2
3
4
E
EPG Setup (setting for receiving EPG data)
If you want to use the EPG for digital stations, select
“Yes”. The EPG data must be automatically captured
while the TV set is in standby mode. After setting to
“Yes”, it may take some time to turn off the power
using the remote control due to the process of the data
capture.
NOTE
• If the TV main power is switched off, the EPG data will not
capture.
E
Display Range Setup
The Display range setup allows you to select three
types of time spans for display on the screen.
E
Genre Icon Setup
You can grey out or place a mark on desired genres
and smoothly search for programmes you frequently
watch.
Genre Icon List
Icon Genre Icon Genre
Movie/Drama Music/Ballet/Dance
News/Current affairs
Arts/Culture (without
music)
Show/Game show
Social/Political Issues/
Economics
Sports
Education/Science/
Factual Topics
Children’s/Youth
programmes
Leisure hobbies
Item
Wide Angle:
Display six hours of programme information.
Zoom: Display three hours of programme information.
Vertical Angle:
Change to the EPG display format with a
vertical time span.
Common Operation EPG display settings
11
Selecting a programme using EPG
3 Check programme information
Press a/b/c/d to select the programme you
want to check.
Press
R.
EPG [Mon]16/04 10:57 AM[DTV-TV] Today (Tue)20 (Wed)21 (Thu)22 (Fri)23 (Sat)24 (Sun)25 (Mon)26
040
10 : 00AM - 1 : 00 AM
BBC News 24 BBC News
Programme Info.
Back to EPG
The BBC’s rolling news service with headlines every 15 minutes.
10 AM 11 0 PM 1 2 3
BBC TWO 002
BBC THREE 007
BBC FOUR 010
BBC FIVE 012
CBBC Channel 030
BBC 1 061
BB22 062
BBC NEWS 24 340
BBCi 351
BBC ONE 999
SIT 1 994
SIT 4 997
This is BBC THREE
BBC NEWS BBC NEWS
BBC NEWS BBC NEWS
This is BBC THREE
BBCi BBCi
This is BBC THREE
R
Next
B
OK
: Select : Enter6: Back
EPG
: Exit
Press OK to tune to the selected programme.
4 Search a programme in a category
Press G.
Press
a/b to select the desired genre, and
then press OK.
Press
a/b to select a programme you want to
watch, and then press OK.
EPG [Mon]16/04 10:57 AM[DTV-TV] Today (Tue)20 (Wed)21 (Thu)22 (Fri)23 (Sat)24 (Sun)25 (Mon)26
Back to EPG
CBBC Cahnnel 030 time Mon 19/05 10 : 50 AM - 11 : 05 AM
BBC TWO 002 School is Lock Mon 19/05 10 : 50 AM - 11 : 10 AM
CBBC Cahnnel 030 Words and Pictures Mon 19/05 11 : 05 AM - 11 : 20 AM
R
OK
: Select : Enter6: Back
EPG
: Exit
Movie/Drama
News/Current affairs
Show/Game show
Sports
Children’s/Youth programmes
Music/Ballet/Dance
Arts/Culture (without music)
Social/Political Issues/Economics
Education/Science/Factual Topics
Leisure hobbies
Today [AM] Today [PM] [Tue] 20 AM [Tue] 20 PM
• Refer to page 11 for the genre setting.
1
2
3
1
2
3
5 Search for a programme by date/time
Press Y.
Press
c/d to select the desired time span and
then press OK.
EPG [Mon]16/04 10:57 AM[DTV-TV] Today (Tue)20 (Wed)21 (Thu)22 (Fri)23 (Sat)24 (Sun)25 (Mon)26
Search by Time
Back to EPG
10 AM 11 0 PM 1 2 3
BBC TWO 002
BBC THREE 007
BBC FOUR 010
BBC FIVE 012
CBBC Channel 030
BBC 1 061
BB22 062
BBC NEWS 24 340
This is BBC THREE
BBC NEWS BBC NEWS
BBC NEWS BBC NEWS
This is BBC THREE
R
Next
Next
B
OK
: Select
: Select Time
: Enter6: Back
EPG
: Exit
Enter +1 Week
G Y
OK
: Enter
0 AM 6 AM
6 AM 0 PM
0 PM 6 PM
6 PM 0 AM
Today
BBC ONE 999
SIT 1 994
SIT 4 997
This is BBC THREE
Press a/b to select the desired programme,
and then press OK.
1
2
3
Basic Operation
E
Display the EPG screen
Selecting a programme
NOTE
• When you select a programme outside of the current time
span, the timer setting screen displays. (Page 13)
Press EPG.
EPG [Mon]16/04 10:57 AM[DTV-TV] Today (Tue)20 (Wed)21 (Thu)22 (Fri)23 (Sat)24 (Sun)25 (Mon)26
040
10 : 00AM - 1 : 00 AM
BBC News 24 BBC News
10 AM 11 0 PM 1 2 3
BBC TWO 002
BBC THREE 007
BBC FOUR 010
BBC FIVE 012
CBBC Channel 030
BBC 1 061
BB22 062
BBC NEWS 24 340
BBCi 351
SIT 3 996
BBC ONE 999
SIT 1 994
SIT 2 995
SIT 5 998
SIT 4 997
This is BBC THREE
BBC NEWS BBC NEWS
BBC NEWS BBC NEWS
This is BBC THREE
BBCi BBCi
This is BBC THREE
OK
: Select : Enter6: Back
EPG
: Exit Programme info. Search By Genre Search By Date Timer List
R G Y B
E
Select a programme
1 Press c/d to select the time
span you want to search.
• Continue to press d to display
programmes in the next time span.
2 Press a/b to select the desired programme.
• If a or b are displayed on the left of the services, continue to press
a/b to display next or previous screen.
E
Close the EPG screen
Press EPG again.
2
1
3 4 5
Programme Information
Watching TV
12
Loading...