Sharp LC-22GA3M, LC-22GA3X Operating Manual

LC-22GA3M/LC-22GA3X
ENGLISH
LC-22GA3M LC-22GA3X
LC-22GA3M LC-22GA3X
OPERATION MANUAL
LCD COLOUR TELEVISION
TINS-B558WJZZ
04P10-JKMA
OPERATION MANUAL
Printed in Japan
Printed on 100% post-consumer recycled paper.
TINS-B558WJZZ
04P10-JKMA
LC-22GA3MX_E_Hyo1_4.p65 2004.10.11, 2:03 PM1
Contents
LC-22GA3M
LC-22GA3X
LCD COLOUR TELEVISION
ENGLISH
OPERATION MANUAL
ENGLISH
ENGLISH
Dear SHARP Customer .................................................... 2
Important Safety Precautions ......................................... 2
Trademarks ....................................................................... 3
Supplied Accessories ......................................................4
Preparation ....................................................................... 5
Installing Batteries in the Remote Control ................... 5
Using Remote Control .................................................5
Power Connection .......................................................6
Antenna Connection ................................................... 6
Listening with Headphones......................................... 6
Part Names of Main Unit .................................................. 7
How to fix the cables ................................................... 8
Part Names of Remote Control .......................................9
Basic Operation..............................................................10
Turning On and Off the Main Power ..........................10
Standby .....................................................................10
Switching the TV/VIDEO Modes (AV1/AV2/AV3/
COMPONENT/TV) .............................................. 10
Sound Volume ........................................................... 11
Changing Channels .................................................. 11
Preset .............................................................................. 12
On-Screen Display Language Selection ................... 12
Presetting the Channels (AUTO) ............................... 12
Presetting the Channels (MANUAL).......................... 13
Channel Setting (AUTO)............................................ 14
Channel Setting (MANUAL) ...................................... 14
CLOCK SETUP .......................................................... 14
Selecting Menu Items .................................................... 15
Basic Adjustment Settings ............................................16
BOOSTER.................................................................. 16
AV MODE .................................................................. 16
Picture Adjustments .................................................. 16
COLOUR SYSTEM (AV1, AV2 or AV3 Mode)............. 17
Colour Temperature................................................... 17
I/P SETUP ..................................................................18
DNR (Digital Noise Reduction).................................. 18
FILM MODE ............................................................... 18
QUICK SHOOT.......................................................... 18
Useful Features .............................................................. 19
Sound Adjustments ................................................... 19
SPEECH EMPHASIS.................................................. 19
DOLBY VIRTUAL ....................................................... 19
WSS (Wide Screen Signalling) .................................. 20
4:3 MODE .................................................................. 20
DISPLAY MODE ........................................................ 20
AV3 IN/OUT ............................................................... 21
On-Screen Display Language Setting ...................... 21
BACKLIGHT .............................................................. 21
WIDE MODE .............................................................. 22
V-POSITION (Vertical Position) .................................. 22
TIMER FUNCTIONS .................................................. 23
AUTO POWER OFF ................................................... 23
NO OPERATION OFF ................................................ 23
BLUE BACK .............................................................. 23
NICAM Broadcast Selection .......................................... 24
A2 Stereo Broadcast Selection ..................................... 25
Teletext ............................................................................ 26
Connecting with External Devices ............................... 28
Example of External Devices that can be
Connected .......................................................... 28
Connecting a VCR, DVD Player or a Camcorder
(COMPONENT/AV-IN1/2/3) ................................ 29
Outputting Video and Audio (Video Output) ............. 29
Troubleshooting ............................................................. 30
Specifications ................................................................. 31
Dimensional Drawings...................................................32
LC-22GA3MX_E_P01-09.p65 04.8.25, 7:53 PM1
1
Dear SHARP Customer
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Precautions carefully before using this product.
Important Safety Precautions
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD colour TV product, please read the following precautions carefully before using the product.
1. Read instructions—All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for future reference.
3. Observe warnings—All warnings on the product and in the instructions must be observed closely.
4. Follow instructions—All operating instructions must be followed.
5. Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
6. Power source—This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.
7. AC cord protection—The AC cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.
8. Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
9. Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.
10. Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.
11. Repair—If any of the following conditions occurs, unplug the AC cord from the AC outlet, and request a qualified service person to perform repairs.
a. When the AC cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive adjustment work
by a qualified technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that
the product needs servicing.
12. Replacement parts—In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.
13. Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.
14. Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.
2
LC-22GA3MX_E_P01-09.p65 04.8.25, 7:53 PM2
Important Safety Precautions (Continued)
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.
•Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub, swimming pool and in a wet basement.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).
• Do not place vases or any other water-filled containers on this product. The water may spill onto the product causing fire or electric shock.
•To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.
•Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.
•To prevent fire or shock hazard, do not place the AC power cord under the TV set or other heavy items.
The LCD panel is a very high technology product with 1,229,760 thin film transistors, giving you fine picture details. Due to the very large number of pixels, a few non-active pixels may occasionally appear on the screen as a fixed point of blue, green or red. This is within product specifications and does not constitute a fault.
Do not display a still picture for a long time, as this could cause an afterimage to remain.
Trademarks
• Micronas® VOICE is a Speech Enhancement and Intelligibility Processing technology by Micronas GmbH.
• Micronas is a trademark of Micronas GmbH.
• Manufactured under license from Dolby Laboratories.
• “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
LC-22GA3MX_E_P01-09.p65 04.8.25, 7:53 PM3
3
Supplied Accessories
LC-22GA3M LC-22GA3X
Make sure the following accessories are provided with the LCD TV set.
Remote control
pages 5 and 9
AC cord
AC adapter
page 6
Antenna cable
*Product shape varies in some countries.
page 6
“AAA” size batteries (×2)
page 5
Cable clamps (×2)
page 8
page 6
Operation manual
4
LC-22GA3MX_E_P01-09.p65 04.9.3, 10:38 AM4
Preparation
+
+
OPC indicator
WAKE-UP TIMER indicator
POWER indicator
OPC sensor
Remote sensor
Installing Batteries in the Remote Control
Before using the LCD TV set for the first time, install the two “AAA” size batteries supplied in the remote control. When the batteries become depleted and the remote control fails to operate, replace the batteries with new “AAA” size batteries.
1 Open the battery cover. 2 Insert two “AAA” size batteries. 3 Close the battery cover.
Slide the cover while pressing the (
) part.
Place batteries with their terminals corresponding to the (+) and (–) indications in the battery compartment.
Engaging the lower claw with the remote control, close the cover.
Caution!
Precautions regarding batteries
Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) indications.
•Different types of batteries have different characteristics. Do not mix batteries of different types.
•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old batteries to leak chemicals.
•Remove batteries as soon as they are depleted. Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe it off with a cloth.
• The batteries supplied with the LCD TV set may have a shorter operating time due to storage conditions.
• If the remote control is not to be used for an extended period of time, remove the batteries from the remote control.
Using Remote Control
Use the remote control by pointing it towards the remote sensor window of the main unit. Objects between the remote control and sensor window may prevent proper operation.
Cautions regarding use of remote control
Do not apply shock to the remote control. In addition, do not expose the remote control to liquids, and do not place it in an area with high humidity.
Do not install or place the remote control under direct sunlight. The heat may cause deformation of the unit.
The remote control may not work properly if the remote sensor window is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or main unit, or operate the remote control closer to the remote sensor window.
5
LC-22GA3MX_E_P01-09.p65 04.8.25, 7:53 PM5
Preparation (Continued)
NOTE
VOLUME
NOTE
Connect to the DC input terminal of the LCD TV set.
POWER INPUT terminal (DC 13V)
Power Connection
MAIN POWER
Household
power outlet
AC cord*
* Product shape varies in
some countries.
Plug into power outlet.
To POWER
INPUT terminal
AC adapter
Using the AC adapter
• Although the AC adapter may become warm during use, this is not a malfunction.
• Do not wrap or cover the AC adapter with a blanket or similar covering. This can cause a malfunction or accident.
• Do not attempt to disassemble or modify the AC adapter. The insides of the AC adapter contain high-voltage components that can result in the risk of electrical shock.
• Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.
• Always turn the MAIN POWER switch of the LCD TV set to OFF when connecting the AC adapter.
• Unplug the AC adapter from the LCD TV set and power outlet when the LCD TV set is not to be used for a long period of time.
Antenna Connection
• Using the supplied antenna cable, connect the room antenna terminal to the antenna terminal on the LCD TV set. (Refer to the figure below.)
ANT. (Antenna terminal)
Antenna cable (supplied)
Room antenna terminal (75-ohm type)
To antenna terminal
Listening with Headphones
Plug the headphone mini-plug into the headphone jack located on the side of the LCD TV set.
On-screen display
Headphones
Adjust the sound volume using VOL (+)/(–).
• Headphones are not included in the supplied accessories.
• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the headphone jack.
6
LC-22GA3MX_E_P01-09.p65 04.9.3, 10:38 AM6
MAIN POWER
MENU
TV/VIDEO
CH
( )/( )
VOL
( )/( )
Upper control panel
Part Names of Main Unit
NOTE
How to adjust the angle
Tilt the display by grabbing onto the carrying handle while securely holding down the stand with your other hand.
Controls
Speaker
Remote sensor
OPC sensor
To change the vertical angle of the LCD TV set, tilt the screen up to 5 degrees forward or 10 degrees backward. The LCD TV set can also be rotated up to 25 degrees to right and left. Please adjust the angle so that the LCD TV set can be watched most comfortably.
(Headphone jack)
Plug the headphone mini-plug into the headphone jack located on the side of the LCD TV set. (See page 6.)
OPC indicator (Optical Picture Control)
The Optical Picture Control indicator lights up green when the “BACKLIGHT” is set to “AUTO (OPC)”. (See page 21.)
WAKE-UP TIMER indicator
The WAKE-UP TIMER indicator lights up red when the wake-up timer is set.
POWER indicator
The POWER indicator lights up green when the power is on, and red when in the standby mode (the indicator will not light when the main power is off).
TV/VIDEO, CH ( )/( ), VOL (–)/(+) and MENU on the main unit have the same functions as the same buttons on the remote control.
LC-22GA3MX_E_P01-09.p65 2004.9.9, 5:48 PM7
Fundamentally, this operation manual provides a description based on operation using the remote control.
7
Part Names of Main Unit (Continued)
Carrying handle
Rear View
COMPONENT
ANT. (Antenna terminal)
POWER INPUT terminal
(DC 13V)
Y
AUDIO (L) AUDIO (R)
PB (CB) P
R (CR)
AUDIO (R)
AUDIO (L)
VIDEO
AV-IN1
AV-IN2
AV-IN3/OUT
AUDIO (R)
AUDIO (L)
VIDEO
AUDIO (R)
AUDIO (L)
VIDEO
S-VIDEO
Cable clamps
Terminals
8
• Secure cables and cords with the supplied cable clamps so that they do not get caught when mounting the cover.
Pull down the hook to open the cover.
How to fix the cables
LC-22GA3MX_E_P01-09.p65 04.10.15, 9:54 AM8
Part Names of Remote Control
SUBTITLE
Displays the Teletext
Subtitle directly.
(P. 27)
OK
(P. 14)
HOLD
Temporarily holds the
current Teletext page.
(P. 27)
TIMER
Displays the Timer functions
Menu screen. (P. 23)
(Mute)
Switches the sound on and off. (P. 11)
Yellow
(P. 26)
Cyan
(P. 26)
Channel Select
TV input mode: Selects the channel.
(P. 11)
Teletext mode: 0-9/Selects the page.
(P. 26)
MENU
Displays the TV menu or returns to normal screen. (P. 14)
VOL (+)/(
-
)
(P. 11)
(Flashback)
Returns to the previous
channel. (P. 11)
Red, Picture Menu
(P. 16, 26)
Right/Left Selection
(P. 14)
RETURN
Returns to the previous screen.
TEXT
Displays the Teletext mode screen. (P. 26)
Upwards/Downwards Selection, Zoom display function (Teletext mode)
(P. 14, 27)
POWER
(P. 10)
MPX
Switches to the audio
mode. (P. 24)
REVEAL
Displays hidden information such as solutions to riddles and puzzles. (P. 27)
TV/VIDEO
Switches the input source between COMPONENT, AV1, AV2, AV3 and TV mode. (P. 10)
SUBPAGE
Displays the Teletext Subpage directly. (P. 27)
DISPLAY
Turns on the status display when the menu is not displayed. (P. 23)
WIDE
Changes the wide image mode. (P. 22)
Dolby V
Selects Virtual Dolby
Surround settings.
(P. 19)
Green, Sound Menu
(P. 19, 26)
CH ( )/( )
TV input mode: Selects the channel. (P. 11) Teletext mode: Selects the page. (P. 26)
LC-22GA3MX_E_P01-09.p65 04.10.20, 10:599
9
NOTE
1
PAL B/G
Basic Operation
NOTE
COMPONENT
AV2
PAL
AV3
PAL
12
PAL B/G
COMPONENT mode
AV1
AV1 mode
AV2 mode
AV3 mode
TV mode
PAL
48 P
0
Turning On and Off the Main Power
MAIN POWER
POWER indicator
Press MAIN POWER. The POWER indicator instantly changes from red to green and the LCD TV set is turned on.
On-screen display
Switching the TV/VIDEO Modes (AV1/AV2/AV3/COMPONENT/TV)
Turn on the power of the connected video equipment.
1
Press TV/VIDEO to select the applicable input source.
2
The screen changes in order of COMPONENT, AV1, AV2, AV3 and TV mode each time TV/VIDEO is pressed.
• The on-screen display disappears after a few seconds.
To turn off the main power, press MAIN POWER again.
Standby
To turn off the LCD TV
Press POWER. The POWER indicator will turn red.
To turn the LCD TV back on
Press POWER again. The POWER indicator will turn green.
• COMPONENT: Select this mode when viewing the signals from the video equipment connected to the COMPONENT terminal.
• AV1: Select this mode when viewing the signals from the video equipment connected to the AV-IN1 terminal. The S-VIDEO terminal is additionally provided for the AV-IN1 terminal. If both S-VIDEO terminal and VIDEO terminal are connected with cables, the S-VIDEO terminal takes priority.
• AV2: Select this mode when viewing the signals from the video equipment connected to the AV-IN2 terminal.
• AV3: Select this mode when viewing the signals from the video equipment connected to the AV-IN3/OUT terminal. AV3 mode is used to adjust the preset settings and In or Out can be selected. AV3 indication is not displayed when Out is selected. (For details on setting “AV3 IN/OUT”, see page 21.)
10
LC-22GA3MX_E_P10-11.p65 2004.9.9, 5:48 PM10
Basic Operation (Continued)
NOTE
VOLUME 50
VOLUME 10
VOLUME 10
1
PAL B/G
--
1-
15
PAL B/G
Sound Volume
To adjust the volume
Press VOL (+) to increase the sound volume.
The numerical value increases.
Press VOL (–) to decrease the sound volume.
The numerical value decreases.
Changing Channels
You can select channels using Channel Select or CH ( )/( ).
To handle the increasing number of channels available, this LCD TV set allows you to select up to 100 positions (Channels 0 to 99). One-digit and two-digit methods of selection can be used. Follow the procedure shown below to select channels.
Using Channel Select
To select a one-digit channel (e.g., Channel 5):
Press 5 of Channel Select.
1
If “5-” is indicated and the picture does not change,
2
press
-/-- to switch over to the 1-digit select mode
and press 5 of Channel Select.
To mute the sound
Press
Press
ee
e (Mute) to temporarily turn off the sound. The
ee
MUTE mark is displayed on the screen.
ee
e (Mute) or VOL (+)/(–) to turn the sound back to
ee
the previous level. MUTE is automatically cleared when one of the following buttons is pressed: POWER, VOL (+)/(–) or
ee
e (Mute).
ee
To select a two-digit channel (e.g., Channel 15):
Press -/-- to set the 2-digit select mode.
1
Press 1 of Channel Select.
2
Press 5 of Channel Select.
3
• Complete this procedure within 4 seconds, otherwise the selection will not be made.
Changing channels with CH ( )/( ) on the remote control.
Press CH ( ) and the channels change in the order shown below: 1 2 3 . . . 98 99 0 1 2 3 . . . Press CH ( ) and the channels change in the order shown below: 3 2 1 0 99 98 . . . 3 2 1 . . .
LC-22GA3MX_E_P10-11.p65 04.8.25, 7:48 PM11
Using
Press
Press
AA
A (Flashback)
AA
AA
A to switch the currently tuned channel to the
AA
previously tuned channel.
AA
A again to switch back to the currently tuned
AA
channel.
11
Preset
31, 24
AUTO(B/G
)
VHF 1
48.25MHZ
NOTE
ENGLISH
21
AUTO(B/G
)
VHF 1
48.25MHZ
1
PAL B/G
NOTE
AUTO MANUAL LANGUAGE NORMAL SCREEN
On-Screen Display Language Selection
MENU on the LCD TV set can also be used to select the
language.
Upper control panel
Press MENU (PRESET-1) on the upper part of the
1
LCD TV set for more than 2 seconds to display the PRESET mode screen.
Press MENU (PRESET-1) twice to display the
2
LANGUAGE select mode screen.
• Press MENU (PRESET-1) again to change the
PRESET mode as shown below.
Presetting the Channels (AUTO)
Automatically tunes in and presets receivable TV stations. Make sure the antenna cable is properly connected.
Upper control panel
Press MENU (PRESET-1) on the upper part of the
1
LCD TV set for more than 2 seconds to display the AUTO mode screen.
Sound System
Instead of pressing MENU for more than 2 seconds, you can set the language by selecting screen. (See page 21.)
Press CH ( )/( ) to select the language you wish to
3
“LANGUAGE” in “SETUP” in the Menu
display.
Press TV/VIDEO to return to the normal screen.
4
Press VOL (–)/(+) (PRESET-2) on the upper part of
2
the LCD TV set. All the TV stations in your area that can be received by the LCD TV set are automatically preset.
The screen shows whatever is on channel 1 when full
3
auto channel preset is finished.
When starting PRESET after setting “SOUND SYSTEM” with MENU on the remote control, “SOUND SYSTEM” for all channels are stored into memory.
Unused channels are automatically skipped.
The Preset mode is only available in the TV mode.
Instead of pressing MENU for more than 2 seconds, you can set the channel by selecting screen. (See page 14.)
“CH SETUP” in “SETUP” in the Menu
12
LC-22GA3MX_E_P12-15.p65 04.8.25, 7:56 PM12
31, 2, 64
AUTO(B/G
)
VHF 1
48.25MHZ
MANUAL(B/G
)
VHF 1
48.25MHZ
MANUAL(B/G
)
UHF 5
623.25MHZ
NOTE
Presetting the Channels (MANUAL)
41, 2, 3, 5
NOTE
MANUAL(B/G
)
VHF 1
48.25MHZ
FINE UHF 5
623.25MHZ
ENGLISH
Press MENU for more than 2 seconds.
AUTO MANUAL LANGUAGE NORMAL SCREEN
Preset (Continued)
Setting a channel to a desired TV station Upper control panel
Press MENU (PRESET-1) on the upper part of the
1
LCD TV set for more than 2 seconds to display the AUTO mode screen.
Press MENU (PRESET-1) to display the MANUAL
2
mode screen.
• Press MENU (PRESET-1) again to change the
MANUAL mode as shown below.
Sound system
In a weak reception area or under bad reception conditions
Upper control panel
Press MENU (PRESET-1) on the upper part of the
1
LCD TV set for more than 2 seconds to display the AUTO mode screen.
2
Press MENU (PRESET-1) to display the MANUAL mode screen.
3
While the MANUAL mode screen is displayed, press MENU (PRESET-1) for more than 2 seconds.
The channel position number remains in green.
Adjust for good reception using VOL (–)/(+).
4 5
After finishing the adjustment, press MENU (PRESET-1) to continue channel presetting.
While the MANUAL mode screen is displayed, press MENU
(PRESET-1). (The LANGUAGE mode screen will appear.)
Select the channel position using Channel Select or
3
4
)/( ).
CH (
Press VOL (–)/(+) to locate the channel you want to preset to the position. Search is initiated and when a TV signal is received during the search, the search stops.
5
Repeat steps 3 and 4 above, to preset the channel positions for other broadcasts, etc.
Press MENU (PRESET-1) twice to return to the
6
normal screen.
System may not have been set correctly, if noise can be heard or if there is no sound. In such a case, adjust “SOUND SYSTEM”. (See page 14.)
LC-22GA3MX_E_P12-15.p65 2004.9.9, 5:48 PM13
13
Preset (Continued)
: :
0
0
0
0 0
0
SOUND SYSTEM B/G
START SEARCH
POSITION CH 1 COLOUR SYSTEM AUTO SOUND SYSTEM B/G SKIP OFF FINE 871.1 MHZ NICAM OFF A2 OFF
0
NOTE
B/G I D/K M
AUTO
N358
PAL60 N443
PAL
SECAM
Channel Setting (AUTO)
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
3
Press '/" to select “CH SETUP”, and press OK.
4
Press '/" to select “AUTO”, and press OK.
5
Press '/" to select “SOUND SYSTEM”. Each time you press \/|, the setting for individual items changes as shown in the table on the right.
Press '/" to the select “START SEARCH”, and press
6
OK to begin the automatic programme search.
When the automatic programme search is completed,
7
the channel first received will be displayed.
Selected item
POSITION
COLOUR SYSTEM
SOUND SYSTEM
SKIP
FINE
NICAM
A2
Switching Colour system: Set the system to Auto for normal TV reception. The Auto mode automatically detects the receiving signal system and changes the reception system of the LCD TV set. When the picture or sound is not stable, switching to an appropriate system may improve the picture or sound quality.
When using Fine tuning, the channel number changes from green to yellow.
To return the channel to its original frequency setting, follow the manual channel preset procedure. (For details “Presetting the Channels (MANUAL)”, see page 13.)
The channel position changes to the upper or lower number.
The mode changes in the following order:
The mode changes in the following order:
The mode changes in the following order:
ON OFF
Channel numbers with a “(RED)” mark on the left are set to Skip. To turn off Skip, press Channel Select to select the desired channel, and then set the Skip mode on the CH setup menu to “OFF”.
The frequency changes to allow fine tuning.
The broadcast sound system changes in the following order:
ON (NICAM sound) OFF (Monaural TV sound)
Stereo system changes in the following order:
ON (A2 sound)
Description
OFF (Monaural TV sound)
Channel Setting (MANUAL)
Perform steps 1 and 2 in Channel Setting (AUTO) to
1
display the Setup Menu screen.
Press '/" to select “CH SETUP”, and press OK.
2
Press '/" to select “MANUAL”, and press OK.
3
4
Press '/" to select the desired adjustment item.
5
Each time you press \/|, the setting for individual items changes as shown in the table on the right.
6
Press MENU to exit.
CLOCK SETUP
The Timer functions that turn power on at the specified time do not work unless the clock has been adjusted. Be sure to adjust the clock first.
1
Perform steps 1 and 2 in Channel Setting (AUTO) to display the Setup Menu screen.
2
Press '/" to select “CLOCK SETUP”, and press OK.
3
Press '/" to set the time, and press OK.
Holding down '/" changes the setting at a high speed.
4
Press MENU to exit.
14
LC-22GA3MX_E_P12-15.p65 2004.9.9, 5:48 PM14
Selecting Menu Items
MENUMENU[SOUND
] PICTURE SOUND SETUP FEATURES TREBLE [ TREBLE [ ] – + BASS [ BASS [ ] – + BALANCE [ BALANCE [ ]L R ADVANCED RESET
0 0 0
MENUMENU[SETUP
] PICTURE SOUND
SETUP
FEATURES CH SETUP CLOCK SETUP WSS 4:3 MODE DISPLAY MODE AV3 IN/OUT LANGUAGE
MENUMENU[FEATURES
]
PICTURE SOUND
SETUP
FEATURES WIDE MODE V-POSITION BACKLIGHT TIMER FUNCTIONS BOOSTER AUTO POWER OFF NO OPERATION OFF BLUE BACK
:SELECT:SELECTOK:ENTER
RETURN:
BACK
MENU:
EXIT
MENUMENU[PICTURE
]
PICTURE SOUND SETUP FEATURES
AV MODE [DYNAMIC] CONTRAST [ 3CONTRAST [ 3 ] BRIGHTNESS [ BRIGHTNESS [ ] – + COLOUR [ COLOUR [ ] – + TINT [ TINT [ ] ] SHARPNESS [ SHARPNESS [ ] – + COLOUR SYSTEM ADVANCED RESET
0 0
0
0 0
NOTE
Menu setting screens
For details on setting each menu item, refer to the page number indicated below.
The illustrations and on-screen displays in this manual are for explanation purposes and may vary slightly from the actual
appearance.
• Depending on the setting condition, such as an input mode, it may not be possible to adjust or set some items. In such cases, the alert message is displayed on the menu setting screen.
PICTURE
The bar above is an operational guide for the remote control. The bar will change in accordance with each menu setting screen.
AV MODE ....................................................... 16
CONTRAST .................................................... 16
BRIGHTNESS ................................................ 16
COLOUR......................................................... 16
TINT ................................................................ 16
SHARPNESS .................................................. 16
COLOUR SYSTEM ........................................ 17
ADVANCED .............................................. 17, 18
RESET ............................................................ 16
Page
SOUND
SETUP
FEATURES
Page
TREBLE .......................................................... 19
BASS .............................................................. 19
BALANCE ....................................................... 19
ADVANCED .................................................... 19
RESET ............................................................ 19
Page
CH SETUP .......................................... 14, 24, 25
CLOCK SETUP .............................................. 14
WSS ................................................................ 20
4:3 MODE ....................................................... 20
DISPLAY MODE ............................................. 20
AV3 IN/OUT .................................................... 21
LANGUAGE .................................................... 21
Page
WIDE MODE ................................................... 22
V-POSITION ................................................... 22
BACKLIGHT ................................................... 21
TIMER FUNCTIONS ...................................... 23
BOOSTER ...................................................... 16
AUTO POWER OFF ....................................... 23
NO OPERATION OFF .................................... 23
BLUE BACK.................................................... 23
LC-22GA3MX_E_P12-15.p65 04.9.2, 10:48 AM15
15
ON
OFF
NOTE
STANDARD
DYNAMIC
MOVIE
GAME
Basic Adjustment Settings
NOTE
PICTURE SOUND SETUP FEATURES
AV MODE [DYNAMIC] CONTRAST [ 3CONTRAST [ 3 ] BRIGHTNESS [ BRIGHTNESS [ ] – + COLOUR [ COLOUR [ ] – + TINT [ TINT [ ] ] SHARPNESS [ SHARPNESS [ ] – + COLOUR SYSTEM ADVANCED RESET
0 0
0
0 0
NOTE
BOOSTER
Picture quality may improve in regions with weak signal strength using this function.
Press MENU to display the Menu screen.
1
Press \/| to select “FEATURES”.
2
3
Press '/" to select “BOOSTER”, and press OK.
4
Press '/" to select “ON”, and press OK.
Press MENU to exit.
5
• If signal strength is strong enough for the selected channel, the effect is negligible and may produce instability. In such a case, select “OFF”.
Selected item
STANDARD
DYNAMIC
MOVIE
GAME
• You can select a different AV Mode item for each input mode. (For example, select “STANDARD” for TV input and “DYNAMIC” for VIDEO input.)
Changing image settings to standard values.
For a clear-cut image emphasising high contrast for sports viewing.
Controlling the contrast to enable easier viewing of dark images.
Controlling the brightness of video games and other images for easier viewing.
Description
Picture Adjustments
Adjust the picture to your preference with the following picture settings.
1
Press MENU to display the Menu screen.
• The Picture Menu screen can be displayed directly by pressing Red.
2
Press \/| to select “PICTURE”.
Press '/" to select a specific adjustment item.
3
AV MODE
AV MODE gives you preset options to choose from, to best match the image based on room-brightness and playback software used.
Press MENU to display the Menu screen.
1
• The Picture Menu screen can be displayed directly by pressing Red.
Press \/| to select “PICTURE”.
2
Press '/" to select “AV MODE”, and press OK.
3
Press '/" to select desired mode, and press OK.
4
Press \/| to adjust the item to your desired position.
4
Press MENU to exit.
5
Selected item
CONTRAST
BRIGHTNESS
COLOUR
TINT
SHARPNESS
• Select “COLOUR SYSTEM” and press OK to select “AUTO”, “PAL”, “SECAM”, “N358”, “N443” or “PAL60”. See page 17.
• Select “ADVANCED” and press OK to set “COLOUR TEMP.”, “I/P SETUP”, “DNR”, “FILM MODE” or “QUICK SHOOT”. See pages 17 and 18.
• When resetting all adjustment items (except for the items on the “AV MODE”, “COLOUR SYSTEM” and “ADVANCED” menu) to factory preset values, perform the following procedure.
1 Press '/" to select “RESET”, and press OK. 2 Press '/" to select “YES”, and press OK.
\\
\ button
\\
For less contrast
For less brightness
For less colour intensity
Skin tones become purplish
For less sharpness
||
| button
||
For more contrast
For more brightness
For more colour intensity
Skin tones become greenish
For more sharpness
Press MENU to exit.
5
16
LC-22GA3MX_E_P16-18.p65 2004.9.9, 5:49 PM16
Basic Adjustment Settings (Continued)
AUTO PAL6
PAL
SECAM
N358
N443
0
NOTE
0
0
0
COLOUR TEMP. RED [ ] – + GREEN [ ] – + BLUE [ ] – + I/P SETUP DNR FILM MODE QUICK SHOOT RESET
USER
HIGH
MIDDLE
LOW
NOTE
COLOUR SYSTEM (AV1, AV2 or AV3 Mode)
Set the system to “AUTO” for normal reception. The “AUTO” mode automatically detects the receiving signal system and changes the reception system of the set. When the picture or sound is not stable, switching to an appropriate system may improve the picture or sound quality.
1
Press MENU to display the Menu screen.
• The Picture Menu screen can be displayed directly by pressing Red.
2
Press \/| to select “PICTURE”.
3
Press '/" to select “COLOUR SYSTEM”, and press
OK.
4
Press '/"/\/| to select “AUTO”, “PAL”, “SECAM”, “N358”, “N443” or “PAL60” and press OK.
Colour Temperature
Adjust the colour temperature to give a better white balance.
Press MENU to display the Menu screen.
1
• The Picture Menu screen can be displayed directly by pressing Red.
Press \/| to select “PICTURE”.
2
Press '/" to select “ADVANCED”, and press OK.
3
Press '/" to select “COLOUR TEMP.”, and press OK.
4
Press '/" to select the desired item, and press OK.
5
Press MENU to exit.
5
“COLOUR SYSTEM” is available only in the AV mode.
Press MENU to exit.
6
Selected item
USER
HIGH MIDDLE LOW
* When you select “USER”, the following items are adjustable.
Selected item
RED
GREEN
BLUE
• When resetting “RED”, “GREEN” and “BLUE” to factory preset values, perform the following procedure.
1 Press '/" to select “RESET” in the “ADVANCED” menu, and
press OK.
2 Press '/" to select “YES”, and press OK.
Can set your desired colour*
White with Bluish tone
White with Reddish tone
\\
Press
\ Press
\\
Weaker red Stronger red
Weaker green Stronger green
Weaker blue Stronger blue
Description
||
|
||
LC-22GA3MX_E_P16-18.p65 2004.9.9, 5:49 PM17
17
Basic Adjustment Settings (Continued)
0
0
0
COLOUR TEMP. RED [ ] – + GREEN [ ] – + BLUE [ ] – + I/P SETUP DNR FILM MODE QUICK SHOOT RESET
INTERLACE
PROGRESSIVE
NOTE
ON
OFF
NOTE
ON
OFF
NOTE
ON
OFF
NOTE
I/P SETUP
Adjusting the image and input signal can give you a more beautiful picture.
Press MENU to display the Menu screen.
1
• The Picture Menu screen can be displayed directly by pressing Red.
Press \/| to select “PICTURE”.
2
Press '/" to select “ADVANCED”, and press OK.
3
Press '/" to select “I/P SETUP”, and press OK.
4
FILM MODE
Automatically detects a film-based source (originally encoded at 24 frames/second), analyses it, and then recreates each still film frame for high-definition picture quality.
1
Perform steps 1 to 3 in I/P SETUP to display the “ADVANCED” screen.
Press '/" to select “FILM MODE”, and press OK.
2
3
Press '/" to select “ON”, and press OK.
4
Press MENU to exit.
• Set “FILM MODE” to “ON” manually to detect a film-based source (originally encoded at 24 frames/second) when the input source has vertical frequency of 60 Hz (e.g. NTSC, PAL60).
“FILM MODE” cannot be set to “ON” when 480P, or 1080Ι signal is received from the COMPONENT terminals.
Film mode does not work frequency of 50 Hz (e.g. PAL, SECAM).
when the input source has vertical
576Ι
, 576P, 720P
5
Press '/" to select “INTERLACE” or “PROGRESSIVE”, and press OK.
6
Press MENU to exit.
Selected item
INTERLACE
PROGRESSIVE
•“I/P SETUP” cannot be set when 480P, 576P, 720P or 1080Ι signal is received from the COMPONENT terminals.
Use this setting when you cannot get a clear picture with Progressive. (Especially suitable for media with special effects like game software.)
Normally, you should select this setting.
Description
DNR (Digital Noise Reduction)
DNR (Digital Noise Reduction) provides high quality images with minimal dot crawl and cross colour noise.
Perform steps 1 to 3 in I/P SETUP to display the
1
“ADVANCED” screen.
Press '/" to select “DNR”, and press OK.
2
QUICK SHOOT
Provides sharp pictures suitable for fast moving images such as a sports programme.
1
Perform steps 1 to 3 in I/P SETUP to display the “ADVANCED” screen.
2
Press '/" to select “QUICK SHOOT”, and press OK.
Press '/" to select “ON”, and press OK.
3
Press MENU to exit.
4
•“QUICK SHOOT” may cause image noise. If this occurs, set the function to “OFF”.
Press '/" to select “ON”, and press OK.
3
Press MENU to exit.
4
• “DNR” cannot be set to “ON” when 720P or 1080Ι signal is received from the COMPONENT terminals.
18
LC-22GA3MX_E_P16-18.p65 04.8.25, 8:08 PM18
SOUND SETUP FEATURES
TREBLE [ TREBLE [ ] – + BASS [ BASS [ ] – + BALANCE [ BALANCE [ ]L R ADVANCED RESET
0 0 0
NOTE
SPEECH EMPHASIS DOLBY VIRTUAL
ON
OFF
NOTE
SPEECH EMPHASIS DOLBY VIRTUAL
ON
OFF
NOTE
DOLBY VIRTUAL [ON] DOLBY VIRTUAL [OFF]
Useful Features
Sound Adjustments
You can adjust the sound quality to your preference with the following settings.
Press MENU to display the Menu screen.
1
The Sound Menu screen can be displayed directly by pressing Green.
2
Press \/| to select “SOUND”.
Press '/" to select a specific adjustment item.
3
4
Press \/| to adjust the item to your desired position.
Press MENU to exit.
5
Selected item
TREBLE
BASS
BALANCE
• Select “ADVANCED” and press OK to set “SPEECH EMPHASIS” or “DOLBY VIRTUAL”. See this page.
• When “OUT ” is selected in “AV3 IN/OUT”, you cannot adjust sound settings.
• When resetting all adjustment items (except for the items on the “ADVANCED” menu) to factory preset values, perform the following procedure.
1 Press '/" to select “RESET”, and press OK. 2 Press '/" to select “YES”, and press OK.
\\
\ button
\\
For weaker treble
For weaker bass
Increase the volume of the left speaker
||
| button
||
For stronger treble
For stronger bass
Increase the volume of the right speaker
•“SPEECH EMPHASIS” cannot be set when “AV3 IN/OUT” is set to “OUT ”.
•“SPEECH EMPHASIS” cannot be set when the headphone mini­plug is plugged into headphone jack.
• Speech emphasis does not work when sound is output from the headphones.
DOLBY VIRTUAL
You can enjoy the Surround 2ch stereo with Dolby Pro Logic technology.
Virtual Dolby Surround is a technology certified by Dolby Laboratories that creates a virtualised surround sound experience from two speakers using Dolby Pro Logic or Dolby Pro Logic ΙΙ.
Virtual Dolby Surround retains all the original multichannel audio information and provides the listener with the sensation of being surrounded by additional speakers.
Perform steps 1 and 2 in Sound Adjustments to
1
display the Sound Menu screen.
2
Press '/" to select “ADVANCED”, and press OK.
Press '/" to select “DOLBY VIRTUAL”, and press
3
OK.
Press '/" to select “ON”, and press OK.
4
Press MENU to exit.
5
ΙΙ
SPEECH EMPHASIS
Micronas® VOICE, Speech Enhancement and Intelligibility Process­ing technology by Micronas GmbH, has the following features:
• Increases the speech signal over background noise to increase intelligibility.
• Separates voice from the background and moves it to the foreground: Voices are moved closer to the listener, while other sounds are moved to the back.
• Improves voices that are hard to understand, but leaves clear voices undisturbed.
Perform steps 1 and 2 in Sound Adjustments to
1
display the Sound Menu screen.
2
Press '/" to select “ADVANCED”, and press OK.
Press '/" to select “SPEECH EMPHASIS”, and press OK.
3
Press '/" to select “ON”, and press OK.
4
5
Press MENU to exit.
•“DOLBY VIRTUAL” cannot be set when “AV3 IN/OUT” is set to “OUT ”.
•“DOLBY VIRTUAL” cannot be set when the headphone mini-plug is plugged into headphone jack.
• Virtual Dolby Surround does not work when sound is output from the headphones.
• When “ON” is selected in “DOLBY VIRTUAL”, you cannot adjust “BALANCE”.
• For some discs, setup may be required on your DVD. In this case, please refer to the operation manual of your DVD player.
Directly setting the Virtual Dolby Surround
Press Dolby V to display the Dolby Virtual screen.
• Each time you press Dolby V, the mode changes as follows. You can select the desired mode.
LC-22GA3MX_E_P19-25.p65 2004.9.9, 5:49 PM19
19
Useful Features (Continued)
ON
OFF
NOTE
NORMAL
PANORAMA
NORMAL
MIRROR
ROTATE
UPSIDE DOWN
ABC
ABC
ABC
ABC
WSS (Wide Screen Signalling)
WSS allows a television to switch automatically among the different screen formats.
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
Press '/" to select “WSS”, and press OK.
3
Press '/" to select “ON” or “OFF”, and press OK.
4
Press MENU to exit.
5
DISPLAY MODE
You can set the orientation of the picture.
1
Press MENU to display the Menu screen.
2
Press \/| to select “SETUP”.
3
Press '/" to select “DISPLAY MODE”, and press OK.
4
Press '/" to select the desired mode, and press OK.
5
Press MENU to exit.
[NORMAL]: Normal image orientation.
[MIRROR]: To display mirror images for special uses.
If an image does not switch to the correct screen format, try to set “WIDE MODE” in “FEATURES”. When the broadcast signal contains no WSS information, the function will not work even if enabled.
WSS information refers to the original wide mode information sent from the broadcasting station.
4:3 MODE
The WSS signal has 4:3 auto-switching that allows you to select between Normal and Panorama.
1
Press MENU to display the Menu screen.
Press \/| to select “SETUP”.
2
3
Press '/" to select “4:3 MODE”, and press OK.
4
Press '/" to select “NORMAL” or “PANORAMA”, and press OK.
5
Press MENU to exit.
[UPSIDE DOWN]: To display upside down images for special uses.
[ROTATE]: To display rotated images for special uses.
20
LC-22GA3MX_E_P19-25.p65 04.9.2, 10:50 AM20
Selected item
NORMAL
PANORAMA
4:3 mode “NORMAL” 4:3 mode “PANORAMA”
Normal range keeping 4:3 or 16:9 aspect ratio.
Wide image without side bars.
WSS signal 4:3 screen
Description
Useful Features (Continued)
AUTO(OPC
)
BRIGHT
NORMAL
DARK
IN
OUT
OUT
NOTE
ENGLISH
AV3 IN/OUT
You can select the AV-IN3/OUT terminal as input terminals or output terminals.
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
Press '/" to select “AV3 IN/OUT”, and press OK.
3
4
Press '/" to select the desired mode, and press OK.
Press MENU to exit.
5
AV3 IN/OUT
[IN]
AV-IN3/OUT terminals selected as input terminals.
[OUT ] Line output is selected,
output volume is fixed and speaker output is available.
[OUT ] Line output is selected,
output volume is variable and speaker output is set to mute.
BACKLIGHT
You can set the brightness of the screen on the LCD TV set.
1
Press MENU to display the Menu screen.
Press \/| to select “FEATURES”.
2
Press '/" to select “BACKLIGHT”, and press OK.
3
4
Press '/" to select the desired mode, and press OK.
Press MENU to exit.
5
Selected item
AUTO (OPC)
BRIGHT
NORMAL
DARK
Screen brightness is adjusted according to the ambient light of the room.
Maximum brightness.
Brightness 60%. Suitable for viewing in well-lit areas. Saves energy.
Brightness 20%. Sufficiently bright when viewing in dim areas.
Description
• “AV3 IN/OUT” cannot be set when “AV3” is selected as an input mode or “AV3” is selected in “CHANNEL” of “WAKE-UP TIMER” in “TIMER FUNCTIONS”.
On-Screen Display Language Setting
You can select English, Chinese or Arabic as the on-screen display language.
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
Press '/" to select “LANGUAGE”, and press OK.
3
Press '/" to select the desired language, and press
4
OK.
Press MENU to exit.
5
21
LC-22GA3MX_E_P19-25.p65 04.9.2, 10:50 AM21
Useful Features (Continued)
NOTE
NORMAL CINEMA 14:9
ZOOM 14:9
PANORAMA
FULL
CINEMA 16:9
NOTE
V-POSITION [ ]– +
0
NOTE
WIDE MODE [NORMAL]
WIDE MODE [ZOOM 14:9]
WIDE MODE [PANORAMA]
WIDE MODE [FULL]
WIDE MODE [CINEMA 14:9]
WIDE MODE [CINEMA 16:9]
WIDE MODE
You can select the picture display size for the playback image of the DVD player.
•“WIDE MODE” cannot be set when 720P or 1080Ι signal is received from the COMPONENT terminals.
1
Press MENU to display the Menu screen.
Press \/| to select “FEATURES”.
2
Press '/" to select “WIDE MODE”, and press OK.
3
Press '/"/\/| to select the desired mode, and press
4
OK.
• If the broadcast signal contains no WSS information, Auto Selection will not function even when the WSS option is enabled.
Directly setting the Wide mode
Press WIDE to display the Wide mode screen.
Each time you press WIDE, the mode changes as follows.
Press MENU to exit.
5
Selected item
NORMAL
ZOOM 14:9
PANORAMA
FULL
CINEMA 16:9
CINEMA 14:9
For 4:3 “standard” pictures. A side bar appears on each side.
For 14:9 letterbox pictures. A thin side bar appears on each side, and you may also see bars on the top and bottom with some programmes.
In this mode the picture is progressively stretched toward each side of the screen.
For 16:9 squeeze pictures.
For 16:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
For 14:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
Description
Auto Selection
If you set “WSS” and “4:3 MODE”, the optimum Wide mode is automatically chosen for every broadcast containing the WSS information.
“WSS” menu
To enable Auto Selection, set “WSS” in the Setup Menu to “ON”. (See page 20.)
“4:3 MODE” menu
To set the type of the wide screen, select “NORMAL” or “PANORAMA” in the 4:3 Mode menu. (See page 20.)
4:3 mode set to
“NORMAL”
4:3 mode set to
“PANORAMA”
V-POSITION (Vertical Position)
Adjusting a picture’s vertical position.
1
Press MENU to display the Menu screen.
Press \/| to select “FEATURES”.
2
Press '/" to select “V-POSITION”, and press OK.
3
Press \/| to adjust the item to your desired position.
4
• Centres the image by moving it up or down.
Press MENU to exit.
5
• You can adjust a different vertical position for each input mode (COMPONENT, AV1, AV2, AV3, and TV).
22
LC-22GA3MX_E_P19-25.p65 04.9.2, 10:50 AM22
ON
OFF
ON
OFF
ON
OFF
NOTE
TIMER FUNCTIONS
3 MIN OFF
6 MIN
9 MIN
12 MIN
15 MIN
0
0
0
0
0
SET OFF WAKE-UP TIME :
CHANNEL CH 1 VOLUME 2
000 0
NOTE
You can set “SLEEP TIMER” and “WAKE-UP TIMER” to automatically turn off and on the LCD TV set.
Press MENU to display the Menu screen.
1
Press \/| to select “FEATURES”.
2
Press '/" to select “TIMER FUNCTIONS”, and press OK.
3
• The Timer functions Menu screen can be displayed directly by pressing TIMER.
4
Press '/" to select “SLEEP TIMER”, and press OK.
Useful Features (Continued)
• You can check the time set in “WAKE-UP TIMER” by pressing DISPLAY.
• When the time set for the “WAKE-UP TIMER” is reached when the power is on, the LCD TV set changes to the set channel. The sound volume does not change at this time.
• “AV3” in “CHANNEL” is not displayed when “OUT ” is selected in “AV3 IN/OUT”.
AUTO POWER OFF
You can set the power to automatically turn off if there is no signal for 5 minutes.
1
Perform steps 1 and 2 in TIMER FUNCTIONS to display the Features Menu screen.
Press '/" to select “AUTO POWER OFF”, and press OK.
2
Press '/" to select “ON”, and press OK.
3
Press MENU to exit.
4
Press '/"/\/| to select “30MIN”, “60MIN”, “90MIN”,
5
“120MIN”, “150MIN” or “OFF”, and press OK.
6
Press '/" to select “WAKE-UP TIMER”, and press OK.
Press '/" to select the desired adjustment item, and
7
press \/| to adjust them.
8
Press MENU to exit.
Selected item
SET
WAKE-UP TIME
CHANNEL
VOLUME
• When you set “WAKE-UP TIMER”, the WAKE-UP TIMER indicator lights up red.
• Be sure to adjust the clock with “CLOCK SETUP” in “SETUP” before setting “WAKE-UP TIMER”.
• You can output the picture and sound of the external device with the “WAKE-UP TIMER” function. Make sure that the external device turns on at the time you specified.
• The “CHANNEL” setting for “WAKE-UP TIMER” changes in the following order: * The skipped channels cannot be selected.
• When not using the LCD TV set for a long period of time, either turn off the main power or “WAKE-UP TIMER” set to “OFF”.
• When “WAKE-UP TIMER” has been set to “ON”, the LCD TV set is turned on at the set time every day until it is set to “OFF”.
• Always make sure to turn off the power with the remote control. “WAKE-UP TIMER” will not be activated if the main power is turned off with MAIN POWER on the LCD TV set.
• After the TV has been turned on by “WAKE-UP TIMER”, “SLEEP TIMER” is automatically set to “120MIN” for safety reason.
To activate the Wake-up timer, set this item to “ON”.
Set the time at which you want to turn on the TV.
Set the TV channel or input mode when the TV is turned on.
Set the volume when the TV is turned on.
COMPONENT → AV1 → AV2 → AV3 →TV (0-99)*.
Description
NO OPERATION OFF
You can set the power to automatically shut down if there is no operation for 3 hours.
Perform steps 1 and 2 in TIMER FUNCTIONS to
1
display the Features Menu screen.
Press '/" to select “NO OPERATION OFF”, and
2
press OK.
Press '/" to select “ON”, and press OK.
3
Press MENU to exit.
4
BLUE BACK
Automatically turns the screen blue if no broadcast signal is received.
Perform steps 1 and 2 in TIMER FUNCTIONS to
1
display the Features Menu screen.
Press '/" to select “BLUE BACK”, and press OK.
2
Press '/" to select “ON”, and press OK.
3
Press MENU to exit.
4
• When received signals are weak or interfered with by some other signals, “BLUE BACK” may be activated. To watch the TV under such conditions, set “BLUE BACK” to “OFF”.
•“BLUE BACK” is activated when AV1, AV2, AV3 or COMPONENT input mode is selected with no signal being input.
23
LC-22GA3MX_E_P19-25.p65 2004.9.9, 5:49 PM23
49
NICAM
STEREO
49
MONO
49
NICAM
M1
49
NICAM
M2
49
MONO
49
NICAM MONO
49
MONO
NOTE
NICAM Broadcast Selection
15
NICAM
NOTE
POSITION CH 1 COLOUR SYSTEM AUTO SOUND SYSTEM B/G SKIP OFF FINE 871.1 MHZ
NICAM OFF
A2 OFF
0
To let you enjoy NICAM broadcasting, this LCD TV set receives NICAM stereo system, bilingual, and monaural broadcasts.
Stereo
The LCD TV set is receiving a stereo broadcast.
• Each time you press MPX, the mode changes between “NICAM STEREO” and “MONO”.
•When “MONO” is selected, the TV sound is output monaurally.
(When stereo sound is received)
Bilingual
The LCD TV set is receiving a bilingual broadcast.
• Pressing MPX changes the audio mode in the order shown below.
• M1=main sound, M2=sub sound, or MONO=monaural sound, can be selected.
(When main sound is selected)
(When sub sound is selected)
If the sound quality is poor due to a weak signal or other problems during NICAM broadcast reception, set the “OFF” position of the NICAM to change the TV sound to monaural.
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
Press '/" to select “CH SETUP”, and press OK.
3
4
Press '/" to select “MANUAL”, and press OK.
5
Press '/" to select “NICAM”, and press \/| to select “OFF”.
(When monaural sound is selected)
Monaural
The LCD TV set is receiving a monaural broadcast.
• Each time you press MPX, the mode changes between “NICAM MONO” and “MONO”.
(When monaural sound is received)
• If approximately 3 seconds pass without a button being pressed,
the mode setting is automatically terminated and the LCD TV set returns to the normal mode.
• The setting can be selected individually for each channel number.
When the NICAM sound is set to the “OFF” position, the TV sound is output in monaural.
Press MENU to exit.
6
(When the “OFF” position is selected)
• When the NICAM sound is set to the “OFF” position, MPX cannot be used to change the audio mode (stereo and bilingual settings).
24
LC-22GA3MX_E_P19-25.p65 2004.9.9, 5:50 PM24
49
STEREO
49
MONO
49
MAIN
49
SUB
NOTE
15
NOTE
A2 Stereo Broadcast Selection
POSITION CH 1 COLOUR SYSTEM AUTO SOUND SYSTEM B/G SKIP OFF FINE 871.1 MHZ NICAM OFF
A2 OFF
0
To let you enjoy A2 stereo broadcasting, this LCD TV set receives A2 stereo system and bilingual broadcasts.
Stereo
The LCD TV set is receiving a stereo broadcast.
• Each time you press MPX, the mode changes between “STEREO” and “MONO”.
•When “MONO” is selected, the TV sound is output monaurally.
(When stereo sound is received)
Bilingual
The LCD TV set is receiving a bilingual broadcast.
• Pressing MPX changes the audio mode in the order shown below.
•MAIN=main sound or SUB=sub sound, can be selected.
(When main sound is received) (When sub sound is received)
If the sound quality is poor due to a weak signal or other problems during A2 stereo broadcast reception, set the “OFF” position of the A2 to change the TV sound to monaural.
Press MENU to display the Menu screen.
1
Press \/| to select “SETUP”.
2
Press '/" to select “CH SETUP”, and press OK.
3
Press '/" to select “MANUAL”, and press OK.
4
Press '/" to select “A2”, and press \/| to select
5
“OFF”.
• If approximately 3 seconds pass without a button being pressed,
the mode setting is automatically terminated and the LCD TV set returns to normal mode setting.
• The setting can be selected individually for each channel number.
When the A2 sound is set to the “OFF” position, the TV sound is output in monaural.
(When the “OFF” position is selected)
b” is displayed when A2 is set to “OFF” during A2 stereo broadcast.
Press MENU to exit.
6
• When the A2 sound is set to the “OFF” position, MPX cannot be used to change the audio mode (stereo and bilingual settings).
LC-22GA3MX_E_P19-25.p65 2004.9.9, 5:50 PM25
25
TELETEXT
100
100 200
TELETEXT
Red Green Yellow
Cyan
100
TELETEXT
Red Green Yellow
Cyan
100
Teletext
What is Teletext?
Teletext is an information service organised like a magazine, which is provided by some TV stations in addition to regular television broadcasting. Your LCD TV set receives special Teletext signals broadcast by a TV station, processes the information and displays it graphically on the screen. News, weather and sports information, stock exchange prices, programme reviews and closed captioning for people hard of hearing are among the many services available through Teletext.
Teletext mode
Teletext is activated with TEXT on the remote control and is also closed with it. The LCD TV set can be controlled in Teletext mode directly by inputting commands with the remote control and indirectly through the on-screen display (menu system).
Operating instructions in Teletext mode
The FLOF system for teletext is transmitted in Singapore currently.
The TOP system for teletext is transmitted in Australia currently.
• If TOP Teletext is broadcast, a control line and TOP line
can be displayed on the screen. The TOP line involves the operating instructions associated with all of the Coloured buttons if TOP text is transmitted, or the operating instructions for only Red and Green if TOP text is not being transmitted.
• If there are subpages, a control line holding the operating
instructions for subpages can be displayed on line 24.
[1] Turning on and off Teletext mode
When viewing the Teletext information
• Press CH ( ) to increase the page number.
• Press CH ( ) to decrease the page number.
• Directly select any page from 100 to 899 by using 0-9.
1
Select a TV channel that is broadcasting the Teletext programme.
Press TEXT to display the Teletext screen.
2
• To turn off the Teletext mode, press TEXT again.
1
[2] Using the TOP line
When TOP Teletext is being broadcast, you can display the TOP line, which contains the operating instructions on the screen.
26
LC-22GA3MX_E_P26-27 04.10.27, 5:06 PM26
Press the Coloured buttons to operate the Teletext screen.
• Press Red to display the previous page and Green to display the next page. Yellow and Cyan are as indicated on the TOP line.
Teletext (Continued)
TELETEXT
100
0002 00 01 02 03
GROUPPAGESBLOCKPAGES
Gesundheit
Geld&Recht
Kind&Kegel CD&BuchTipp Multimedia Auto&Reise Reise Ferien Horoskope Phone
INDEX
Übersicht Nachrichten Wetter Sport TV-Programme
Service
Boulevard
ABC DEF
ABC DEF
[3] Changing subpages
If a page has been selected from among several subpages, you can display a control line which contains the subpage numbers.
Press SUBPAGE.
1
• The control line with the subpage numbers is displayed on line 24, and the number of the currently selected subpage is displayed in blue.
[5] Using Teletext menu
To select the character set
During Teletext broadcast, press MENU to display the
1
“CHARACTER SET” screen.
CHARACTER SET
ARABIC/HEBREW WEST EUROPE EAST EUROPE TURKISH/GREEK
Press '/" to select the desired character set.
2
The colour of the letters will turn to yellow. When selecting
the character set, pressing OK will change the letters to grey for an instant and then return them back to yellow.
Press \/| to select the desired subpage number.
2
• The selected subpage is displayed.
•You can also use Channel Select to select the desired subpage.
Press SUBPAGE to turn off the control line.
3
[4] Using the TOP table
When TOP Teletext is being broadcast, you can display the TOP table with the current programme data if one exists.
Press OK to display the TOP table.
1
• The Teletext page is temporarily turned off.
TOP table
Press MENU to exit.
3
[6] Useful Features for Teletext
HOLD on the remote control can be used to hold the
current teletext page. Press the button again to cancel the hold mode.
'/" can be used to zoom the current teletext page as
shown below.
The screen is displayed in each mode each time '/" is
pressed.
2
3
4
LC-22GA3MX_E_P26-27 04.9.15, 6:20 PM27
Press '/" to select the desired item.
•Press \/| to select topics (column 1) or subtopics (column 2) if they exist.
Press OK.
•A page associated with the selected item is displayed.
Press TEXT to exit.
SUBTITLE can be used to quickly activate subtitles.
Press TEXT to deactivate subtitles.
REVEAL can be used to display hidden information such
as solutions to riddles and puzzles. Press the button again to hide the information.
27
Connecting with External Devices
NOTE
You can enjoy picture and sound by connecting a VCR or a home video game system to the terminals located on the rear of the LCD TV set. When connecting an external device, turn off the power of the LCD TV set first to prevent any possible damage.
Example of External Devices that can be Connected
To AV-IN1 terminal
<Example>
• Camcorder
• Home video game system
*If your external device has an S-VIDEO terminal,
S-VIDEO connection is recommended.
To AV-IN2/3 terminal
<Example>
To COMPONENT terminal
• VCR
<Example>
• DVD Player, etc.
*If your external device has a COMPONENT
terminal, COMPONENT connection is recommended (you can view high-quality pictures).
For the cable, use a commercially available audio/video cord.
Only connect audio/video signals to AV-IN1, AV-IN2 and AV-IN3/OUT terminals. Connecting other signals may result in a malfunction.
AV-IN1 has 2 video input terminals: VIDEO and S-VIDEO. When you connect external devices to both terminals (and if you select AV-IN1),
you can only view pictures from the S-VIDEO terminal. To view the picture from the VIDEO terminal, do not connect any external devices to the S-VIDEO terminal.
For more information about external device connections, see the manuals of your external devices.
28
LC-22GA3MX_E_P28-32.p65 04.8.25, 7:55 PM28
Connecting with External Devices (Continued)
NOTE
NOTE
Connecting a VCR, DVD Player or a Camcorder (COMPONENT/AV-IN1/2/3)
Component cable
(commercially available)
Y
P
B (CB)
P
R (CR)
Audio cable
(commercially available)
S-Video cable
(commercially available)
Audio/Video cable
(commercially available)
Audio/Video cable
(commercially available)
Audio (L)
Audio (R)
S-Video
Video
Audio (L)
Audio (R)
Video
Audio (L)
Audio (R)
DVD Player
Camcorder
VCR
VCR
If your VCR (or other external devices) has an S-Video terminal, S-Video connection is recommended. (Use an S-Video cable.)
When you connect external devices to both S-VIDEO and VIDEO terminals, you can only view pictures from the S-VIDEO terminal.
You cannot view multiple or synthesised pictures by connecting two or more external devices. When connecting an external device, use
care to connect the video and audio cables to the corresponding terminals.
When a monaural audio source is connected to only one of the AUDIO input terminals, sound will be heard not from both speakers but from only one speaker.
Outputting Video and Audio (Video Output)
You can output video and audio data from the LCD TV set through the AV output terminals (AV-IN3/OUT).
When using AV-IN3/OUT as an OUTPUT terminal, select “SETUP” in the Menu and set “AV3 IN/OUT” to “OUT”. (See page 21.)
• The factory setting for “AV3 IN/OUT” is “IN”.
Connect to a VCR, audio amplifier, etc.
The AV-IN3/OUT terminal has 2 output modes (see page 21).
When using the S-VIDEO input for AV-IN1, no video output will be made to the AV output terminal, but audio output will be made for
connection to external audio systems.
When using the S-VIDEO input for AV-IN1 or Y, PB (CB) and PR (CR ) input for COMPONENT, no video output will be made to the AV output terminal, but audio output will be made for connection to external audio systems.
29
LC-22GA3MX_E_P28-32.p65 2004.9.9, 5:50 PM29
Troubleshooting
Before calling for repair services, check the following items for possible remedies to the encountered symptoms.
LCD TV set
Sound
Problem Check item
• Make sure the AC adapter is properly inserted in the power
Picture
Picture
There is no picture or sound.
There is no picture. There is no picture from AV-IN1/2/3.
There is no sound.
There is no picture or sound, just noise.
outlet.
•Reception other than those of broadcasting stations can be considered.
• Make sure the input mode is set to the LCD TV set.
• Make sure the MAIN POWER switch of the LCD TV set is on.
• Make sure Picture adjustment is properly adjusted.
• The fluorescent lamp may have reached the end of its service life.
• Make sure the S-VIDEO terminal has nothing connected.
• Make sure the volume is not set to minimum.
• Make sure the sound is not set to mute.
• Make sure the antenna cable is properly connected.
• Bad reception can be considered.
Reference
page
6
10 10
16
8, 29
11 11
6 –
The Picture is not clear.
The Picture is too light or improp­erly tinted.
The picture is too dark.
Remote control does not work.
Unit cannot be operated.
• Make sure the antenna cable is properly connected.
• Bad reception could be the problem.
•Check colour adjustment. (NTSC mode)
• Check if “BACKLIGHT” is set to “DARK”.
•Check “CONTRAST”.
• The fluorescent lamp may have reached the end of its service life.
• Check if batteries in the remote control have sufficient power.
• Make sure the remote sensor window is not under strong lighting.
•External influences such as lightning, static electricity, etc., may cause improper operation. In this case, operate the unit after first turning the power off, or unplugging the AC cord and re­plugging it in after 1 or 2 minutes.
6 –
16
21 16
5 5
Cautions regarding use in high and low temperature environments
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
•Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. (Storage temperature: –20°C to +60°C)
30
LC-22GA3MX_E_P28-32.p65 2004.9.9, 5:50 PM30
Antenna
Troubleshooting (Continued)
Problem Check item
• The reception may be weak.
The picture is not sharp.
The picture moves.
The picture is doubled or tripled.
The picture is spotted.
• The state of the broadcast may also be bad.
•Make sure the antenna is facing the correct direction.
•Make sure the outside antenna has not been disconnected.
•Make sure the antenna is facing the correct direction.
•Broadcast waves may be reflected from adjacent mountains or buildings.
• There may be interference from automobiles, trains, high-voltage lines, neon lights, etc.
• There may be interference between the antenna cable and power cable. Try positioning them further apart.
There are stripes on the screen or colours fade.
• Is the unit receiving interference from other devices? Transmission antennas of radio broadcasting stations and transmission antennas of amateur radios and cellular phones may also cause interference.
• Use the unit as far apart as possible from devices that may cause possible interference.
Specifications
ITEMS
LCD panel 22" (55 cm) Advanced Super View & BLACK TFT LCD Number of pixels 1,229,760 dots WVGA Video colour systems World multi system
TV Standard (CCIR) PAL: B/G, I, D/K NTSC:M SECAM: B/G, D/K TV Tuning System Auto preset tuning
TV function STEREO/BILINGUAL NICAM-B/G, I, D/K A2 stereo-B/G
AUTO PRESET Yes
CATV S1~S41 ch. Hyper Band 4-LINE DIGITAL COMB FILTER Yes Brightness 450 cd/m Lamp life 60,000 hours* Viewing angles H: 170° V: 170° Audio output 5 W × 2 Speakers 6 × 12 cm, 2 pcs.
COMPONENT Y, PB (CB), PR (CR)/Audio (L/R)
AV-IN1 Composite Video, S-Video, Audio Terminals AV-IN2 Composite Video, Audio
AV-IN3/OUT Composite Video, Audio IN/Composite Video, Audio Out
Headphone jack 3.5 mm ø jack (Side) OSD LANGUAGE English/Chinese/Arabic Power requirement DC 13 V, AC 110–240 V, 50/60 Hz
Power Consumption
Weight 8.9 kg w/o accessories
* The typical period of time after which the lamp’s power output will have decreased by about half, given that the AQUOS is used continuously
in a 25°C room under standard lighting and brightness conditions.
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for the LCD TV set improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
MODEL
2
65 W (1.1 W at Standby): AC 230 V 50 Hz (With AC adapter)
53 W : DC 13 V
LC-22GA3M / LC-22GA3X
LC-22GA3MX_E_P28-32.p65 2004.9.9, 5:50 PM31
31
384
212
567
100
490 (including rubber foot)
175
353
439
496 (including rubber foot)
272
476
244
178
86
63
90
100
43.9
Dimensional Drawings
Unit: mm
32
LC-22GA3MX_E_P28-32.p65 04.8.25, 7:55 PM32
Loading...