Sharp IV-08MTV Instruction Manual

Download

Page 1

Version 1.3

Created in December 2004

Instruction Manual

for

IV-08MTV

LCD Color Monitor

- This manual was written with the utmost care. However, if you have any questions

or inquiries concerning the product, please feel free to contact our dealers or service

agents.

- Copying all or part of this booklet is prohibited.

- The contents of this manual may be revised or modified for improvement without

prior notice.

Thank you for purchasing our IV-08MTV LCD

Color Monitor.

Before using it, read this manual carefully to

become familiar with its functions and proper

use.

Notes

Page 2

Safety Precautions

Read this user's manual and the attached documents carefully before installing, operating, or performing any maintenance, in order to keep the machine working correctly. Make sure you understand all of the equipment details, safety information, and cautions before using this machine. In this user's manual, the safety precautions are categorized as "Caution."

Caution : Improper handling may cause dangerous situation, moderate or light injury, or damage

to equipment.

Even when only a Caution is given, serious results may occur depending on the circumstances. In all cases, important points are described. Be sure to follow the advice given.

The following symbols are used to prohibit or explain required action.

: This means do not do what is described. For example, prohibited disassembly is shown as .

(1) Installation

Caution

- Use only in the environments specified in the leaflet, or instruction manual. Electric shock, fire or malfunction may result if used in high temperature, high humidity,

dusty or corrosive environments, or if excessive vibration or impact occurs.

- Install the equipment only as described in the instruction manual. An improper installation may cause the equipment to fall, breakdown, or malfunction.

- Never leave wire cuttings or any other foreign matter lying about. A fire, breakdown or malfunction may result from inappropriate objects left near the equipment.

(2) Connection

Caution

- To provide power to the IV-08MTV, use only the specialized AC cord and adapter that come with the monitor.

- The included AC power cord is for plugging the monitor into a 100 VAC outlet.

- If you need to plug the monitor into a 200 VAC outlet, please contact our sales division or the shop where you purchased the monitor.

- Do not use the specialized AC cord and adapter that come with the IV-08MTV to power any other devices.

(3) Maintenance

Prohibit

- Don't disassemble or modify the Monitor. Fires, breakdowns or malfunctions may occur, if the monitor is disassembled.

- 1 -

Page 3

1. Outline / Features

The IV-08MTV (or simply the Monitor) is a compact, 8.4" screen liquid crystal color monitor.

- It meets the IP65 regulations (when installed in a frame) making it suitable for FA use.

- The Monitor's brightness, color, and contrast can be adjusted and the display language can be switched between Japanese and English.

- An external monitor can be connected to its video output terminal.

The Monitor has an NTSC video output terminal so a separate monitor can be used to check the settings on IV series controllers or for remote monitoring.

- NTSC video input and analog RGB input terminals are standard

The Monitor can be used as a display monitor for any equipment with an NTSC output, such as the SHARP IV-S30 series, IV-C35M etc., and it can be used as a monitor for the SHARP IV-S51M (analog RGB output) or as a monitor for a personal computer.

- 2 -

Page 4

2. Precautions for Use

Please note the following points when handling the Monitor.

(1) Installation location and environment

- The Monitor should be used in a location with an ambient temperature of 0 to 45 oC and a relative humidity of 90%RH or less.

If the ambient temperature is higher than the maximum temperature above, install a fan for forced air cooling or an airconditioner to conditioning the space to bring the ambient temperature within the specified range.

- Do not install the Monitor in a location subject to condensation due to rapid temperature changes.

- Do not install the Monitor in a location exposed to direct sunlight.

- Do not install the Monitor in a location directly subject to vibration or mechanical shock.

- Do not install the Monitor in a location exposed to corrosive or combustible gas, or to solvents or coolants. Do not install it in a location where there is lots of dust, salt in the air or metal powder.

(2) Installation

- Allow adequate ventilation space. If the ventilation area is blocked the internal temperature of the Monitor may increase enough to cause a fire.

- Do not install the Monitor in a panel that contains high-voltage equipment. Install the Monitor at least 200 mm away from high voltage lines or power lines.

(3) Use

- Use only the AC cord and adapter that come with the Monitor. Using any other cord or adapter may cause a fire.

- If the Monitor will not be not used for a long time, unplug cord from the AC outlet.

- If a fault or error occurs in the Monitor (overheating, abnormal odor, or smoke), stop operation immediately and contact the shop where you purchased the Monitor or contact our service company.

- Glass is used in the display. Therefore, do not drop it or bang it.

- In a dry atmosphere, static electricity may build up on your body. If the static electricity is discharged by touching the display, the electronic parts inside the Monitor may be damaged. Discharge any static electricity in your body by touching a grounded metal object before touching the Monitor.

(4) Maintenance

- Only authorized service personnel are allowed to remove the back cover on the Monitor. Some parts in the Monitor use high voltage and you may receive an electric shock or damage the Monitor if you are not trained.

- Turn OFF the power before cleaning the Monitor. Wipe off any dirt using a dry, soft cloth. Use of any thinner or other chemicals may damage the frame or screen and may cause color changes. If the cloth is too hard, it may scratch the display surface.

- 3 -

Page 5

3. System Configuration

IV-08MTV

POWER

Adj.

Video cable (Commercially available item: Less than 10 m)

Monitor cable *2

(cable length: 2 m)

Analog RGB cable (Commercially available item)

IV-S30 series IV-C35

IV-S51M

POWER

+24V

USB

COM

USB

TERMINATOR Y6

LINK

LAN

Y10

EXP

Y11

Y12

Y13

ANALOG

Y14

RGB

Y15

RDY

HALT

C (-)

CAMERA1

IV MONITOR

ONLY

CAMERA2

X10

X11

X12

X13

X14

X15

C (+)

IV-08MTV

POWER

Adj.

[For simultaneous monitoring at another location]

*1: The Monitor is compatible with the following IV-S30 series controllers.

Product name Controller (model name)

Compact image sensor camera (IV-S30 series)

Compact color image sensor camera

Image sensor camera

IV-S31M, IV-S32M, IV-S33M

IV-S31MX, IV-S32MX, IV-S33MX

IV-C35M

IV-S51M

*2: The monitor cable comes as an accessory with the IV-S30 series (controller),

and the IV-C35M. If you need a cable longer than 2 m, purchase a standard cable locally.

Personal computer (Commercially available item)

- 4 -

Page 6

4. Name and Function of Each Part

[Top view]

[Front view]

220.6

(7) Mounting holes (4 positions: two at bottom)

235

(Unit: mm)

[Side view]

53.3

177.6

192

(6)

[Rear view]

key

Adj key

Adj.

ANALOG

RGB

VIDEO

OUT

POWER

(5) Power lamp

Power key

VIDEO

DC24V

(8) M4 Screw hole

(4 positions: For the mounting stand)

(9) Cable clamp

(4) Analog RGB connector

(3) Video output terminal

(1) DC input terminal

(2) Video input terminal

- 5 -

Page 7

FunctionName

DC input terminal

(1)

(24 VDC)

Video input terminal

(2)

(VIDEO IN)

Video output terminal

(3)

(VIDEO OUT)

Analog RGB

(4)

connector (ANALOG RGB)

(5)

Power lamp (POWER)

Power key

[Adj] key

(6)

key

(7)

Mounting hole (for the mounting bracket)

(8)

Screw hole (for a support stand)

(9)

Cable clamp

Terminal used to supply power to the Monitor.

- Connect the cable from AC adapter here (Monitor accessory).

Terminal used to supply an NTSC video signal (from an IV-S30/C35M etc.) to the Monitor.

- Connect a monitor cable here (IV-S30/C35M accessory).

Terminal used to output an NTSC video signal from the Monitor.

- Connect another video monitor here (or IV-08MTV) to see the same image elsewhere at the same time.

Terminal used to input analog RGB signals from an IV-S51M, or a personal computer.

- Connect an analog RGB cable here (available locally).

Lights when power is supplied to this Monitor.

Turn the power to this Monitor ON/OFF. [Adj] key

Press the [Adj] key and the adjustment menu will appear on the display.

- Select items (brightness etc.) on the adjustment menu. Then set the value using the / keys. Confirm the setting with the [Adj] key.

Holes (4 positions) to install the Monitor using the mounting bracket (Monitor accessory).

Screw holes (4 positions) for installing the Monitor on a specialized support stand (custom order item).

Secure the AC adapter cord (Monitor accessory).

- 6 -

Page 8

5. Installation Method

Secure the Monitor using the mounting bracket (Monitor accessory) in the mounting holes on the Monitor housing (4 positions). For specific external dimensions, see Section 4. "Name and Function of Each Part", in this manual.

1) Cut a rectangular hole (222±0.5 x 179±0.5 mm) in the control panel (thickness: Max. 7 mm) and install the Monitor housing in this hole.

Max. 7 mm

Mounting hole in the mounting bracket

(4, including 2 on the bottom)

IV-08MTV

192

235

Installation section

A (See the cross section view below)

2) Insert a mounting bracket (2 each at the top and bottom) into each mounting hole on the housing, and secure the mounting brackets using the mounting screws.

Max. 7 mm

Mounting bracket

Installation section

53.3 mm

5.6 mm

(Cross-section from position A in the figure above)

Mounting screw

Mounting holes of the mounting brackets (totally 4 including top and bottom sides)

- 7 -

Page 9

[Rear view when mounting the Monitor using the mounting brackets]

198.8

10.6 10.6

177.6

220.6

235

(Unit: mm)

192

- 8 -

Page 10

When using the specialized stand

Install the Monitor on the specialized stand (custom order item). Then the Monitor can be used in a standalone configuration.

IV-08MTV

Stand

Rotation center

■Dimensional drawings when the Monitor is installed on the stand

Mounting screws on the Monitor housing

Plan view of the stand

Mounting holes (4 positions)

5.2

1252.5

(stand accessories)

230

127.5

125

23.522.9

235

230

130

53.3

192

230.7

148

1252.5

127.5

- 9 -

Page 11

6. Connection Method

[1] To connect the Monitor to an IV-S30 series controller or an IV-C35M

Connect the NTSC video input terminal (VIDEO IN) on the Monitor to the monitor connector on the IVS30 series (controller), or the IV-C35M, using the monitor cable (*1).

[Rear view of the IV-08MTV]

IV-S30 series IV-C35M

ANALOG

RGB

VIDEO

Video input terminal

(VIDEO IN)

VIDEO

DC 24V

OUT

Monitor connector

Monitor cable *1

(Cable length: 2 m)

*1: The monitor cable is an IV-S30 series and IV-C35M accessory.

If you need a cable longer than 2 m, purchase one locally.

- 10 -

Page 12

[2] To connect the Monitor to an IV-S51M or a personal computer

Connect the analog RGB connector (ANALOG RGB) on the Monitor to the analog connector on the IVS51M or personal computer using an analog RGB cable (purchase one locally). A connection example using an IV-S51M is shown below

[Rear view of the IV-08MTV]

IV-S51M

+24V

Y10

Y11

Y12

Y13

Y14

Y15

RDY

HALT

ANALOG

RGB

VIDEO

OUT

VIDEO

DC 24V

Analog RGB cable

C (-)

X10

X11

X12

X13

X14

X15

C (+)

(purchased locally)

〜

"Pin numbers and signal names" in the analog RGB connector (ANALOG RGB)

POWER

USB

COM

USB

TERMINATOR

LINK

LAN

EXP

CAMERA1

IV MONITOR

CAMERA2

Analog RGB monitor connector

ANALOG

RGB

(ANALOG RGB)

ONLY

D-Sub (female) 15-pin

ANALOG

RGB

15 11

610

10 11 12 13 14 15

Signal namePin No.

1 2 3 4 5 6 7 8 9

VGA-R VGA-G VGA-B

−

DGND AGND AGND AGND D5V DGND

−

DDC SDA HSync VSync DDC SCL

- 11 -

Page 13

[3] Power connections

Provide power by connecting the DC input terminal (24 VDC) on the Monitor to the AC adapter. Then plug the AC cord from the adapter (*2) into a 100 VAC power outlet. Make sure to connect the ground line on the power cord plug to a ground terminal on the power outlet.

[Rear view of the IV-08MTV]

ANALOG

VIDEO

RGB

DC 24V

OUT

DC input terminal

(24 VDC)

*2: The AC adapter and AC cord are accessories that come with the Monitor.

AC adapter *2 AC cord *2

Power cord plug

IV-08MTV connector

Ground line

Secure the AC adapter cord using the cable clamp.

Cable clamp

DC 24V

Power output

(100 VAC)

- 12 -

Page 14

[4] To connect two IV-08MTV monitors

ANALOG

RGB

VIDEO

OUT

VIDEO

DC 24V

IV-08MTV

[Simultaneous monitoring at another location]

ANALOG

RGB

VIDEO

OUT

VIDEO

DC 24V

IV-08MTV

Video input terminal

(VIDEO IN)

IV-S30 series or others

Video cable

(available locally: less than 10 m)

Video output terminal

(VIDEO OUT)

Connect the NTSC video output terminal (VIDEO OUT) on the IV-08MTV to the NTSC video input terminal (VIDEO IN) on another IV-08MTV using a standard video cable (available locally: less than 10 m). Then, you can monitor simultaneously at another location. The video output and video input terminals are RCA connectors.

- 13 -

Page 15

7. How to Adjust the Screen Display

This chapter describes the adjustment procedures and display items on the Monitor.

[1] Adjustment procedure

Adjust the display as follows.

1. Turn ON the power to the Monitor (Press the power key on the Monitor).

2. Press the [Adj] key on the Monitor. => The main menu will appear.

3. Select the item you want to adjust from the main menu using key. => A detailed menu will appear.

4. On the detailed menu, select the item you want to adjust using and keys. Then press the [Adj] key. => The setting for that item will be displayed.

5. Set (or change) the item using the and keys. Then press the [Adj] key.

6. When through making changes, use the and keys to select "RETURN" and then press the [Adj] key.

7. Use the and keys to select "EXIT." Then press the [Adj] key. => The adjustment screen will be closed and the current settings will be saved.

[2] Adjustment item

The items affecting the screen display (that can be adjusted) vary with the type of input signal (ANALOG RGB or VIDEO).

(1) When a video input signal is used

Main menu

LUMINANCE

CHROMINANCE

DISPLAY

LANGUAGE

OSD DISPLAY

TIMER *

MODEL SELECT

SOURCE

RECALL EXIT

Detailed menu (default values)

BACKLIGHT (85) BRIGHTNESS (70) CONTRAST (75) RECALL RETURN SATURATION (80) HUE (50) RECALL RETURN SHARPNESS (53) QUALITY (20) H.POSITION (43) V.POSITION (56) RECALL RETURN

JAPANESE/ENGLISH (JAPANESE)

OSD H-POS (50) OSD V-POS (50) OSD TIMER (11) OSD TRANSPARENCY (50) RECALL RETURN TIMER (0) SHARP IV/OTHER (SHARP IV) VIDEO 1 ANALOG RGB RETURN

and keys. Then press the [Adj]

- 14 -

Page 16

(2) When an analog RGB input signal is used

Main menu

AUTO SETUP

LUMINANCE

DISPLAY

LANGUAGE

OSD DISPLAY

TIMER *

SOURCE

RECALL

EXIT

Detailed menu (default values)

BASIC ADJUST AUTO COLOR ADJUST

RETURN

BACKLIGHT (85) BRIGHTNESS (100) CONTRAST (100) RECALL RETURN

H.POSITION (43) V.POSITION (56) CLOCK (50) PHASE (0) SHARPNESS (0) QUALITY (20) SUB PIXEL RECALL RETURN

JAPANESE/ENGLISH (JAPANESE)

OSD H-POS (50) OSD V-POS (50) OSD TIMER (11) OSD TRANSPARENCY (50) RECALL RETURN TIMER (0) VIDEO 1 ANALOG RGB RETURN

* The TIMER above is the "off delay timer" for switching OFF the

backlight. (Can be set to 5, 10, 15, 30, 60, or 120 minutes)

- 15 -

Page 17

(1) General specifications

Item Specifications

Power supply Power consumption

Ambient storage temperature

8. Specifications

100 to 240 VAC, 50/60 Hz (using the accessory AC adapter)

10 W

- 20 to + 60

Ambient operating temperature

Ambient humidity

Environmental atmosphere

Protective construction

Vibration proof

Shock proof

Noise immunity

Dielectric strength

Insulation resistance

External dimensions (mm)

0 to 45

35 to 90 %RH (non condensing)

No corrosive gases

Conforms to IP65 (front operation section only)

Meets JIS B 3502 standards (when mounted in a control panel)

Vibration and acceleration: 0.15 mm (10 to 58 Hz), 9.8 m/s

(58 to 150 Hz) Vibration frequency: 10 to 150, 150 to 10 Hz. (1 octave/minute) 2 hours each in the X, Y, and Z directions (Number of sweeps: 15)

Meets JIS B 3502 standards (when mounted in a control panel)

147 m/s

(3 times each in the X, Y, and Z directions)

1000 Vp-p, 1 µs width impulse

- Test made using a noise simulator. Charge voltage (100 VAC) on the primary side of the AC adapter

One minute at 1500 VAC (between the plug of the AC cord and the chassis)

500 VDC, 10 M-ohm or more (between the plug of the AC cord and the chassis)

235 W x 192 H x 53.3 D

Panel cutout dimensions (mm)

Weight Accessories

222 ±0.5W x 179 ±0.5H

Approx. 1.6 kg

One AC cord, One AC adapter, 4 mounting brackets, one Instruction manual.

- 16 -

Page 18

(2) Performance specifications

Item Specifications

Display size

Display type

Driving system

Number of pixels

8.4 inches diagonal: 170.4 W x 127.8 H mm

Transmissive type TFT liquid crystal panel

TFT active matrix driving system

921,600 pixels: (640 W x 480 H) x 3, Ratio of functional pixels: 99.99%

or better

Display color

Screen brightness

Backlight working life

Number of pixels

Signal system *3

Image input connector

Image output connector

Approximately 262,000 colors

230 cd/m

20,000 hours on average *1

800 x 600 pixels *2

NTSC, analog RGB (when connected to an IV-S51M)

RCA connector (1 channel), D-sub 15 pin (1 channel)

RCA connector (1 channel)

- When inputting an NTSC video

Fine adjustment function (Display language selectable:

- When inputting an ANALOG RGB

Japanese/English)

signal:

SATURATION, HUB, MODEL SELECT

signal: AUTO SETUP (position, color etc.), CLOCK, PHASE, SUB PIXEL.

- Common to NTSC VIDEO INPUT and ANALOG RGB INPUT: BRIGHTNESS, CONTRAST, BACKLIGHT, SHARPNESS, QUALITY, horizontal/vertical position adjustment, position of the adjustment display screen, OSD TIMER, OSD TRANSPARENCY, change default setting between NTSC VIDEO / ANALOG RGB, RECALL.

*1: The life span is determined when the ambient temperature is held at 25 ±5

C and the brightness

remains above 50% of the default value (or the backlight does not flicker).

*2: When connecting the Monitor to a personal computer with screen resolution greater than 800 x 600

pixels (such as 1024 x 786), a "NOT supported" message will appear. Before connecting the

personal computer, change the screen resolution on the personal computer to "800 x 600."

*3: The input signal selection can be changed on the adjustment screen.

If you want the Monitor to connect equipment made by other manufacturers, check the compatibility using the actual equipment.

- 17 -