Sharp IV-08MP Instruction Manual
TOP - 1
Instruction Manual
Thank you for purchasing the SHARP IV-08MP LCD
monitor. Read this introductory instruction manual
carefully to thoroughly familiarize yourself with the
functions and proper procedures for operation.
• This manual was written with the utmost care. However, if you have any question or
inquiries concerning the product, please feel free to contact our dealers or service agents.
• Copying all or part of this booklet is prohibited.
• The contents of this manual may be revised or modified for improvement without prior
notice.
Notes
LCD monitor
IV-08MP
Version 1.0
Produced in Jan. 2004
Components - 1
The components of IV-08MP are as follows.
Components of IV-08MP
Accessories
One(1) LCD monitor IV-08MP
• Four (4) Main housing angle brackets
• Two (2) Controller angle brackets
• Two (2) Securing screws
• One (1) Stylus pen
• One (1) Instruction manual
Sefety - 1
(1) Installation
• Use only in the environments specified in the catalog and instruction manual.
Electric shock, fire or malfunction may result if used in the environment with high temperature,
high humidity, dust, corrosive gas, excessive vibration or impact.
• Install the equipment only as described in the manual.
An improper installation may cause the equipment to fall off, breakdown, or malfunction.
• Never leave debris from wire cutting or any other foreign matter in the equipment.
It may cause a fire, breakdown or malfunction.
(2) Wiring
• Connect only to the specified power source.
Connection to the wrong power source may cause a fire.
• Wiring should be performed by a qualified electrician.
Improper wiring may lead to a fire, machine failure or electric shock.
(3) Maintenance
• Do not disassemble or modify the camera.
It may cause a fire, breakdown, or malfunction.
Safety Precautions
Read this instruction manual and the attached documents carefully before installing, operating, or per-
forming any maintenance, in order to keep the machine working correctly. Make sure you understand all of
the equipment details, safety information, and cautions before using this machine. In this user's manual,
the safety precautions are categorized as "Caution".
: Improper handling may cause dangerous situation, moderate or light injury, or damage to
equipment.
Even when is given, serious results may occur depending on the circumstances. Be sure to follow
the advice given.
The following symbols are used to prohibit action.
: This means do not do what is described. For example, prohibited disassembly is shown as .
Caution
Caution
Caution
Caution
Prohibit
1 - 1
1. Outline/ Features
This touch panel type 8.4-inch TFT color LCD monitor , the IV-08MP, realizes power saving, automation and
cost saving in inspection/measurement processes as the monitor for image sensor in various arenas. Using
LCD with high-brightness and wide viewing angle, this monitor which is thinner and smaller than CRT can be
easily mounted to the equipment. The touch panel provides a function to enter various settings to the controller (IV-S51M) by simply touching the screen. Also, since the IV-S51M can be connected directly to the
backside of the IV-08MP to be used as one unit, the space required to install the unit will be smaller.
Features
Thin and light weight. Direct connection to the IV-S51M.
The low-profile monitor with approx.46mm in depth is designed to provide easy installation to the
equipment or the wall panel. Since the IV-S51M can be connected directly to the backside of the IV08MP to be used as one unit, the space which would be required for wiring cables to the controller
will be saved.
High-brightness and wide viewing angle for better viewing experience. TFT color LCD.
Using the high-brightness (more than 400cd/m2) TFT color LCD, this monitor can be used in the
bright
environment. The wide viewing angle provides the wider range with up/down: 40°/60°, and left/right:
65°.
IV-S51M settings can be entered from the touch panel.
By simply touching the screen, measurement program or setting of various parameters for the image
sensor camera, IV-S51M, can be easily entered.
2 - 1
2. Precautions for Use
Pay attention to the points below when handling the IV-08MP.
(1) Installed location and environment
• Use the equipment in the environment where the ambient temperature is 0~40°C and the relative
humidity is less than 90% RH. If the ambient temperature is out of the above range, install a forced
fan or an air conditioner to keep the temperature within the required range.
• When this equipment and the controller (IV-S51M) are directly connected and used as one unit,
make sure that the ambient temperature at this equipment side is within 0 to 40°C.
• Avoid installing this equipment in the place where the temperature would change drastically causing
condensation.
• Avoid installing this equipment in the place where it would be exposed to the direct sunlight.
• Do not install this equipment in the place where excessive vibration or impact would directly affect
the equipment.
• Avoid installing this equipment in the place where it would be exposed to water, corrosive gasses,
combustible gasses, solutions, or grinding oil. Do not install the equipment in the place with too
much dust, salt, or iron.
(2) Mounting
• Provide enough space for ventilation. If the ventilation is blocked, the internal temperature of the
equipment may rise resulting in a fire.
• Avoid mounting this equipment onto the panel where high-tension equipment is installed. Keep this
equipment away from high-tension cable or electric motor cable by at least 200mm when the equip-
ment is mounted.
(3) Use
• Do not use the power supply of this equipment to power other equipment. Do not use any power
supply other than 24V DC.
• Discontinue the use of this equipment promptly when any abnormality (over heat, odor, smoke, etc.)
or failure is observed, and contact our dealers or service agents.
• Do not drop or give a strong impact to this equipment. It may damage the glass of display part.
• In dry environment, a human body may charge excessive static electricity. Static electricity may
cause a damage to the components built inside of this equipment (base plate). Discharge the
electricity first by touching the grounded metal before touching this equipment.
(4) Maintenance
• Except for a service representative, do not take off the back cover or the mounting frame of this
equipment.
Touching high-voltage parts inside of the equipment may cause electric shock or machine failure.
• Clean this equipment with soft dry cloth while the power supply is OFF. The use of thinner or other
solutions may cause deformation or discoloration of the equipment. The use of hard cloth may
cause scratches on the screen and other damages.
3 - 1
3. System Configuration
IV-S50 series controller can be directly connected to the backside of the IV-08MP monitor and used as
one unit.
IV-08MP can also be connected to the controller using the monitor cable.
Direct connection
* Monitor cable IV-S50MC2 is sold separately. The monitor cable needs to be purchased, when the
monitor cable is used to
connect the equipment and the controller.
Connection using monitor cable
IV-S51M
IV-08MP
IV-08MP
IV-S51M
(when vertically placed)
Monitor cable*
Monitor input connector
Backside of equipment
IV monitor connector
(IV MONITOR ONLY)
LINK
RX
RGB
ANALOG
EXP
X15
X14
X13
X12
X11
X10
X9
X8
X7
X6
X5
X4
X3
X2
X1
X0
C (+)
+0V
+24V
C (-)
RDY
RUN
Y15
Y14
Y13
Y12
Y11
Y10
Y9
Y8
Y7
Y6
Y5
Y4
Y3
Y2
Y1
Y0
FG
TERMINATOR
USB
USB
LAN
IV MONITOR
ONLY
COM
IV-S51M
POWER
CAMERA2
CAMERA1
(Cable length: 2m)
Loading...