Sharp DV-NC70W, DV-NC70 User Manual

Download

VCR/DVD COMBINATION

MODEL

DV-NC70W DV-NC70 DV-NC70X

OPERATION MANUAL

EJECT/STOP

OPERATE

PLAY/×2

REW

AV 2 IN

L(MONO)-AUDIO-R

VIDEO

REC

VCR/DVD SELECTOR

TIMER

VCR DVD

STOP

OPEN/CLOSE

PLAY

• This Operation Manual explains operation for three models (DV-NC70W, DV-NC70 and DV-NC70X) available in the two geographic areas listed below. Take care to make sure that the instructions you read are for your particular area.

1. DV-NC70W, DV-NC70 .... Hong Kong: Region Number 3

2. DV-NC70X ....................... Australia: Region Number 4

PAL NTSC

DV-NC70W DV-NC70

DV-NC70X

NTSC/PAL

Only for DV-NC70W

ENGLISH

......GB1 – GB104

......C1 – C104

About This Manual

• All mentions of “the Remote” refer to the remote control unit.

• The following table describes the icons used in this Operation Manual.

Icon Meaning

Tips and Hints for easier operation

DVD

VIDEO

C D

Functions for DVD

Functions for VIDEO CD

Functions for Audio CD

GENERAL INFORMATION

CONNECTION AND INITIAL SETTING

VCR, DVD SETUP

WA TCHING THE VCR, DVD

OTHER INFORMA TION

Important!

Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand for future reference when you experience operational problems.

SAFETY INFORMATION

<Only for DV-NC70W/70> Note:

This Product can be used only where the power supply is AC 110V-240V, 50/60Hz. It cannot be used elsewhere.

<Only for DV-NC70X> Note:

This Product can be used only where the power supply is AC 240V, 50Hz. It cannot be used elsewhere.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MA Y RESULT IN HAZARDOUS RADIA TION EXPOSURE.

AS THE LASER BEAM USED IN THIS PRODUCT IS HARMFUL TO THE EYES, DO NOT A TTEMPT TO DISASSEMBLE THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

• This Product is classified as a CLASS 1 LASER product.

• The CLASS 1 LASER PRODUCT label is located on the rear cover.

• This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

CLASS 1 LASER PRODUCT

(Rear of product)

INFORMATION

GENERAL

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

Laser Diode Properties

Material: AlGaInP Wave length: 650 nm Emission Duration: Continuous Laser output: Max. 0.7 mW

Power Cord Protection

To avoid any malfunctions of the Product, and to protect against electric shock, fire or personal injury, please observe the following.

• Hold the plug firmly when connecting or disconnecting the AC power cord.

• Keep the AC power cord away from heating appliances.

• Never put any heavy object on the AC power cord.

• Do not attempt to repair or reconstruct the AC

power cord in any way.

SA005WJ

CAUTION-LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.

VORSICHT-LASERSTRAHLUNG, WENN GEFFNET. BLICKEN SIE NICHT IN DEN STRAHL UND BETRACHTEN SIE DIESEN NICHT DIREKT MIT OPTISCHEN INSTRUMENTEN.

ATTENTION-RADIATION LASER EN CAS D'OUVERTURE. NE PAS FIXER LE FAISCEAU NI REGARDER DIRECTEMENT DES INSTRUMENTS OPTIQUES.

VARNING-LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN MED OPTISKA INSTRUMENT.

VARO ! AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN LAITTEEN LAPI.

VARNING-LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN GEMON OPTISKT INSTRUMENT.

ADVARSEL-LASERSTRÅLING NÅR DEKSEL ÅPNES. STIRR IKKE INN I STRÅLEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.

ADVARSEL-LASERSTRÅLING VED ÅBNING. SE IKKE IND I STRÅLENHELLER IKKE MED OPTISKE INSTRUMENTER.

SAFETY INFORMATION

Location and Handling

• Do not place your Product in closed spaces or do not cover it to prevent excessive temperatures inside the Product.

• Do not place the Product in direct sunlight, or near heat sources.

• Keep the Product away from strong magnetic objects.

• Do not place any object containing water or other liquids on the Product. In the event that liquid should enter the cabinet, unplug the Product immediately and contact the retailer or service centre approved by SHARP immediately.

• Do not remove the Product cabinet. Touching parts inside the cabinet could result in electric shock and/ or damage to the Product. For service and adjustment inside the cabinet, call a qualified dealer or service centre approved by SHARP.

Nonuse Periods

When the Product is not being used, switch the Product to the standby mode. When left unused for a long period of time, the Product should be unplugged from the household AC outlet.

No Fingers or Other Objects Inside

Do not put any foreign object on the disc tray.

Stacking

Place the Product in a horizontal position, and do not place anything heavy on it.

Condensation

Moisture may form on the pickup lens in the following conditions:

• immediately after a heater has been turned on.

• in a steamy or very humid room.

• when the Product is suddenly moved from a cold

environment to a warm one.

If moisture forms inside this Product, it may not operate properly. In this case, turn on the power and wait about one hour for the moisture to evaporate.

Cleaning

Unplug your Product before cleaning. Use a damp cloth for cleaning. Do not use cleaning fluids or aerosols which could enter the Product and cause damage, fire, or electrical shock. These substances may also deteriorate the finish of your Product.

If There is Noise Interference on the TV While a Broadcast is being Received

Depending on the reception condition of the TV, interference may appear on the TV monitor when you watch a TV broadcast while the Product is turned on. This is not a malfunction of the Product or the TV. To watch a TV broadcast, turn off the Product.

Service

Do not attempt to service this Product yourself. Please refer any service to the nearest service centre approved by SHARP.

Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Please refer to relevant laws in your country.

Copy Protection

This Product supports Macrovision copy protection. On DVDs that include a copy protection code, if the contents of the DVD are copied using a VCR, the copy protection code prevents the videotape copy from playing normally.

Apparatus Claims of U.S.Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093 licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Recommended Measures for Optimum Picture Excellence

The Product is a precision device that is constructed using extremely accurate technology. Soiling or friction affecting the pickup lens or disc drive can impair the image quality. neither video nor audio will be played back. To obtain optimum picture quality, the Product should be checked (cleaning and replacement of some parts) every 1,000 hours. Note that this period varies depending on the environment (temperature, humidity, dust, etc.) in which the Product is used. Contact your authorized Sharp supplier for details.

At the worst,

Do not attempt to clean the pickup lens yourself.

T ypes of Discs that Can Be Played on This Product

This Product can play back discs bearing any of the following marks:

DVD See DVD-R/DVD-RW* See [8cm(3") disc/12cm(5") disc]

4.7

VIDEO CDs • Supports up to version 2.0. [8cm(3") disc/12cm(5") disc]

Audio CDs See [8cm(3") disc/12cm(5") disc]

CD-R/CD-RW [8cm(3") disc/12cm(5") disc]

Other CDs

1) On CD-G and CD-EXTRA discs, only the sound can be played (no images).

2) Photo CD, DVD-ROM, DVD-RW (Video Recording Format), DVD-Audio, SACD, SVCD and CD-ROM discs cannot be used.

3) Discs with unusual shapes (heart-shaped or hexagonal discs) cannot be used. The use of such discs will cause a fault.

• This Product will reject an incompatible disc, therefore the disc type should be checked.

* Disks that have not been finalized cannot be played

back. In addition, disks that have been recorded with the video recording format (VR Recording) also cannot be played back.

• Discs recorded in MP3 file format or Audio format.

1 2 on the next page

3 on the next page

This Product will output NTSC signals when playing “NTSC discs”. NTSC signals cannot be converted to modified PAL signals. An NTSC TV or NTSC-compatible Multi-system TV must be used when playing NTSC discs.

DVD-R/DVD-RW Recording Modes

The video mode refers to a mode that allows playback with an ordinary DVD player. It is the mode that allows recording onto disks of DVD-R Ver. 2.0 or later or DVD-RW Ver. 1.1 or later. The video recording format (VR Recording) refers to the recording mode that allows various recording functions and editing in compliance with the standard specifications of the DVD Forum. (Cannot be played back with this Product)

•

DVD video players and discs are designed with region numbers which dictate the regions in which a disc can be played. If the region number on the disc you want to play does not match the region number in this Product, you will not be able to play the disc.

Samples of region number marks compatible

The region number for this Player is

with this Player:

.... ........

Disc playable in all regions

213 546

ALL

Samples of region number marks compatible

The region number for this Player is

with this Player:

.... ........

213 546

ALL

Disc playable in all regions

As for the list of the region number 3, 4 countries and the world map for all region numbers, refer to pages 102 and 103.

T ypes of Discs that Can Be Played on This Product

Disc Function or Operation that is Not Available

In the cases listed below, the or indicator may appear on the TV screen, which indicates that the function or operation is not available.

• When you intend to perform the function or operation on which the manufacturer restriction is imposed: The specific functions on some DVDs and VIDEO CDs are determined by the disc manufacturer. As this Product plays disc data in accordance with the guidelines of the disc manufacturer, some functions may not be available on some discs. Be sure to read the documentation provided with the disc.

• When you intend to perform the functions or operations prohibited for the current disc: The types of functions and operations that can be used for a particular disc vary depending on the features of that disc. Some disc functions and operations may differ from the descriptions given in this Operation Manual. In this event, follow the instructions given on the screen.

Icons Used on DVDs

Sample Icons

1. English

2. Chinese

Number of audio tracks

• This Product supports 2-channel (L/R) audio and 5.1ch (Multi-channel) MPEG Audio 1/2 (only when the DIGITAL OUT coaxial jack is used for connection). It does not support 7.1 channel MPEG Audio Version 2.0.

• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown.

Type of subtitles recorded

1. English

2. Chinese

16:9

Screen aspect ratio recorded

multiple camera angles

Region code indicatorDisc with

Title, Chapter and T racks

• DVDs are divided into “titles” and “chapters”. If the disc has more than one movie on it, each movie would be a separate “title”. “Chapters”, on the other hand, are sections of titles.

Example: DVD

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2

• VIDEO CDs and Audio CDs are divided into “tracks”. You can think of a “track” as one tune on an Audio CD.

Example: VIDEO CD or Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do not.

Disc Handling and Maintenance

Handling Precautions

• Hold the disc by the edges so the surface will not be soiled with

(

fingerprints. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on the label side with a ball-point pen or other writing utensils.

• Do not use record cleaning sprays, benzine, thinner , static electricity prevention liquids or any other solvent.

• Be careful not to drop or bend the disc.

• Do not install more than 1 disc on the disc tray.

• Do not try to close the disc tray when the disc is not installed

properly.

• Be sure to store the disc in its exclusive case when not in use. Then store upright.

• Do not stick paper or adhesive labels to the disc.

)

(

)

If the Surface is Soiled (C)

Wipe gently with a soft, damp (water only) cloth. When wiping discs, always move the cloth from the center hole towards the outer edge. (If you wipe the discs using a circular motion, circular scratches are likely to occur, which will cause noise.)

If the playing surface of a disc is soiled or scratched, the Product may decide that the disc is incompatible and eject the disc tray, or it may fail to play the disc correctly. Wipe any soiling off the playing surface with a soft cloth.

Disc tray

Disc

If the Disc is Brought from a Cold to a Warm Environment, Dew May Form on the Disc

Wipe the dew off with a soft, dry, lint-free cloth before using the disc.

Improper Disc Storage

You can damage discs if you store them in the following places:

• Areas exposed to direct sunlight

• Humid or dusty areas

• Areas directly exposed to a heat outlet or heating appliance

Maintenance

• Be sure to turn the Product off and disconnect the AC power cord before maintaining the Product.

• Wipe this Product with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth which has been dipped in a weak soap-and-water solution and wrung out thoroughly and then wipe again with a dry cloth.

• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. And do not use compressed air to remove dust.

Contents

GENERAL INFORMATION

SAFETY INFORMATION ................................ 1

Types of Discs that Can Be Played on

This Product .............................................. 3

Disc Handling and Maintenance .................. 5

Features ......................................................... 8

Accessories ................................................... 8

Major Components........................................ 9

CONNECTION AND INITIAL SETTINGS

Basic Connection........................................ 14

Connecting to ANTENNA IN/RF OUT ..............14

Connecting a TV Equipped with

VIDEO/AUDIO Input Jacks ..........................15

Using the Component Colour (Y, P

and P

R (CR)) Output Jacks ...........................15

(CB),

DVD Audio Connections ............................. 16

Connecting a TV Equipped with S-VIDEO

Input Jacks...................................................16

Connecting to Audio Equipment.......................16

Playing 2 channel audio................................16

Playing Dolby Digital (5.1 channel), DTS or

MPEG audio ...............................................17

Preparations Before Using the Product.... 18

Adjusting the Video Channel ..................... 19

Auto Tuning System ................................... 21

VCR SETUP

VCR Setup.................................................... 24

Menu Screen ....................................................24

Mode Selection.................................................25

Setting the Channels ........................................27

Auto Tuning ......................................................28

Manual Tuning..................................................30

Channel Skip/Cancelling Skip ..........................32

Channel Skip.................................................32

Cancelling Skip .............................................34

Setting the Clock ..............................................35

Initial Setting of Clock ...................................35

Changing the Clock Setting ..........................36

Setting the Language .......................................37

VCR-RESET .................................................37

Initial Setting of Language ............................37

Changing Language......................................37

VCR Display Information ............................ 38

How to Display Indicators.................................38

VCR Front Panel Display .................................38

DVD SETUP

DVD Setup.................................................... 40

About the SETUP Screen.................................40

TV MODE Setting.............................................41

PARENTAL Level Setting .................................42

AUDIO Setting..................................................44

Setting the COMPRESSION

(Dolby Digital output level)..........................44

Setting the DOLBY DIGITAL .........................45

Setting the MPEG .........................................46

Setting the CINEMA VOICE..........................46

DISC LANGUAGE Setting................................47

Setting SUBTITLE,

AUDIO and MENU languages ....................47

Selecting languages from OTHER................48

DVD Display Information ............................ 49

Operation Mode Indicators ...............................49

Language Code List for Disc Language ... 50

WATCHING THE VCR

Playback....................................................... 52

Inserting a Video Cassette ...............................52

Playback...........................................................52

Video Search (with the Remote).......................52

Fast Forwarding and Rewinding.......................53

Slow Motion Playback (with the Remote).........53

Still Picture and Frame Advance ......................53

Double Speed Playback ...................................53

NTSC Tape Play Back on PAL TV ....................54

Full Auto Playback ............................................54

Auto Head Cleaning System ............................54

Auto Tracking Control System..........................54

Quick Start with Full Loading Mechanism ........54

AUTO RENTAL.................................................55

COLOUR ..........................................................55

BLUE BACK .....................................................56

Playback of Hi-Fi Recorded Tapes ...................57

Audio Output Mode ..........................................57

Adjusting Hi-Fi Audio Tracking .........................57

Sharp Super Picture.................................... 58

Auto Repeat ................................................. 59

Auto Zero Back............................................ 60

DPSS (Digital Program Search System)

/Skip Search ............................................ 61

DPSS................................................................61

Skip Search ......................................................61

TV Programme Recording.......................... 62

Cassette Erase Protection................................62

Recording a TV Programme.............................62

To Watch Another TV Programme While

Recording.....................................................62

Recording NICAM/IGR Multiplex Broadcasts...63

Simple Recording Timer............................. 64

Immediate Recording .......................................64

Programming the Timer with G-CODE® System

(DV-NC70W only)..................................... 65

Setting the Programme Number In Step 4 .......67

Recording with the Timer ........................... 68

Confirming Timer Programmes ........................71

Cancelling Timer Programmes .........................72

Tape Dubbing .............................................. 73

Recording a DVD Disc onto a Video

Cassette ................................................... 74

Recording a DVD disc onto a Video cassette

(Tape Editing mode)..................................... 74

WATCHING THE DVD

Contents

About the Function Control Screen .......... 85

Direct skip (title [track]/chapter/time) ................86

Subtitle language setting ..................................87

Angle setting.....................................................88

Audio setting.....................................................89

3D VIRTUAL SURROUND setting ...................90

DIGITAL GAMMA setting..................................91

Direct Selection of Scenes ......................... 92

Selecting Scenes by Title Number ...................92

Selecting Scenes from the Menu Screen .........92

Programmed Playback ............................... 93

Chapter Programmed Playback .......................93

Track Programmed Playback ...........................94

MP3 Files Programmed Playback ....................95

Repeat Playback.......................................... 96

Repeat playback...............................................96

A-B Repeat.......................................................97

Resume Function ........................................ 98

OTHER INFORMATION

Troubleshooting.......................................... 99

Definition of Terms.................................... 101

Specifications............................................ 104

INFORMATION

GENERAL

CONNECTION AND

INITIAL SETTINGS

VCR SETUP

DVD SETUP

WATCHING

THE VCR

Preparing to Use DVD................................. 78

When connecting a TV with the

DVD output jacks .........................................78

When connecting a TV with the

DVD/VCR shared output jacks ....................78

Playback....................................................... 79

Basic Play.........................................................79

Track Direct Playback.......................................79

Fast Forward/Fast Reverse..............................80

Slow-Motion Play..............................................80

Still/Pause ........................................................81

Frame Advance ................................................81

Skip (Forward/Reverse) ...................................81

Angle Selection ........................................... 82

Playing MP3 Discs ...................................... 83

Regarding MP3 discs .......................................83

Playing MP3 discs ............................................83

To play MP3 discs ............................................84

To play another file (music title) while playing ..84

To skip the file while playing .............................84

THE DVD

INFORMATION

WATCHING

OTHER

Features

■ Common Features

• A DVD, AUDIO CD, VIDEO CD player and VCR all in one.

• Simultaneous VCR recording and DVD playback.

■ VCR

• Hi-Fi Stereo Sound, NICAM/IGR System

• 380-times High Speed Rewind Function (in NTSC)

• S-VHS Simple Playback

• HQ (High Quality) Circuitry

• Simple Recording Timer

• Sharp Super Picture

CODE

• G-

* For Hong Kong: G-

■ DVD

• Plays DVD, VIDEO CD and Audio CD discs as well as CD-R/CD-RW discs recorded in MP3 file format

• 3D Virtual Surround provides high-quality surround sound

• Digital Gamma correction

• Dolby Digital*

• High-quality digital images

• High-quality digital sound

*1 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of *2 “DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.

System*............... only for DV-NC70W

CODE

is a registered trademark of Gemstar Development Corporation. The G-

manufactured under license from Gemstar Development Corporation.

, DTS*2, MPEG Audio digital out capability

Dolby Laboratories.

CODE

system is

Disc Features and this Operation Manual

• The types of functions and operations that can be used for a particular disc vary depending on the

features of that disc. In some cases, these functions and operations may differ from the descriptions given in this Operation Manual. In this event, follow the instructions given on the screen. This Operation Manual only covers basic disc operations.

• For some operations, the or indicator may appear on the TV screen. This indicates that

the operation described in this Operation Manual is not permitted for the current disc.

Accessories

G-CODE

PROG

Two batteries

(AA, R6 or UM/SUM-3 )

for the Remote

VIDEO/AUDIO cable

TIMER

OPERATE

ON/OFF

DISPLAY

SCREEN

FUNCTION

PROG/

CONTROL

REPEAT

TITLE

CLEAR RETURN

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

TAPE

SKIP

SPEED

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

EJECT

VCR MENU DVD SETUP

DVD MENU

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

DV- NC70X

OPEN/ CLOSE

SET

ENTER

SLOW

VCR/DVD

SELECTOR

ANGLE

AUDIO

OUTPUT

Remote control unit

RF cable

Operation Manual

Major Components

VCR Main Unit (Front)

18 52

OPERATE EJECT/STOP

Numbers in refer to the main pages in this Operation Manual where the topic is explained.

Cassette compartment

VCR/DVD SELECTOR

TIMER indicator

Front AUDIO/ VIDEO input

jack

PLAY/×2

AV 2 IN

REW

REC

OPERATE

VIDEO

L(MONO)-AUDIO-R

EJECT/STOP

52 52

62 38

PLAY/×2

REW

REC

VCR Front Panel Display

Operation status

Indicator

Timer Recording

Indicator

Audio Output

Indicator

VCR

L R

SEPVP D

VCR/DVD SELECTOR

VCR DVD

STOP

OPEN/CLOSE

TIMER

PLAY

Tape Speeds

Indicator

Clock Indicator

Channel Indicator

Tape Counter Indicator

38 38 38

Major Components

DVD Main Unit (Front)

Numbers in refer to the main pages in this Operation Manual where the topic is explained.

Disc tray

OPERATE

EJECT/STOP

PLAY/×2

REW

AV 2 IN

VIDEO

L(MONO)-AUDIO-R

VCR/DVD SELECTOR

DVD Front Panel Display

TITLE

Indicator

TRACK

Indicator

CHAPTER

Indicator

OPEN/CLOSE

STOP

OPEN/CLOSE

REC

VCR/DVD SELECTOR

VCR DVD

TIMER

PLAY

Disc operation buttons (PLAY, STOP)

VCR DVD Indicator

PROGRAM Indicator

Operation status/Time Indicator

You can toggle between 1 and 2 by pressing the remote control unit’s

DISPLAY button (page 49).

VIRTUAL surround

Indicator

REPEAT Indicator

ANGLE Indicator

Remote (VCR Operation Buttons)

• The explanations on this page use the VCR/DVD CHANGE Switch in the VCR position.

Numbers in refer to the main pages in this Operation Manual where the topic is explained.

Major Components

TIMER ON/OFF

OPERATE

DISPLAY

ON SCREEN

CURSOR ( / / / )

CLEAR

Number buttons

AM/PM or

REW

PLAY

REC

STOP

TAPE SPEED

CH /

VCR/DVD CHANGE Switch

67 18 38 38 20 60

36 52

52 62 52 62 38

TIMER

OPERATE

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

INPUT SELECT

PLAY

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

REV FWD

REC

TAPE

SPEED

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

VCR/DVD SELECTOR

SET

ZERO BACK

SKIP SEARCH

VCR DVD

INPUT SELECT

PAUSE/ STILL

53 61

SLOW —/±, DPSS —/

SLOW

AUDIO OUTPUT

G-CODE

PROG

Loading the Batteries

1 Open the battery cover

by pulling the lid in the direction of the arrow.

VCR/DVD COMBINATION

2 Load the batteries.

Load the two batteries supplied with the Remote so that the battery poles

and are positioned as indicated.

(AA, R6 or UM/SUM-3)

3 Close the battery cover

by lowering the lid in the direction of the arrow.

Major Components

Remote (DVD Operation Buttons)

• The explanations on this page use the VCR/DVD CHANGE Switch in the DVD position.

Numbers in refer to the main pages in this Operation Manual where the topic is explained.

PROG , REPEAT

FUNCTION CONTROL

93 96

OPERATE

ON SCREEN

DISPLAY

TITLE

RETURN

Number buttons

REV

STOP

49 49

85 92

TIMER

OPERATE

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

INPUT SELECT

PLAY

STOP

DPSS SKIP

AUDIO

OUTPUT

VCR DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

REV FWD

REC

TAPE

SPEED

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

VCR/DVD SELECTOR

ANGLE

DVD SETUP

OPEN/CLOSE

DVD MENU

ENTER CURSOR ( / / / )

PLAY

FWD

PAUSE/STILL

SLOW

SKIP

VCR/DVD CHANGE Switch

VCR/DVD COMBINATION

• Do not subject the Remote to shock, water or excessive humidity.

• The Remote may not function if the Product sensor is in direct sunlight or any other strong light.

• Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries properly.

• Do not mix old and new batteries, or mix brands in use.

• Remove the batteries if you do not use the Remote for an extended period of time.

Main Unit (Rear)

To an AC outlet

DVD Coaxial DIGITAL

output jack

COMPONENT

(CB)

(CR)

DVD OUT

LINE OUT 2

S-VIDEO

DIGITAL

Major Components

VCR

DVD/VC R

ANTENNA IN

LINE IN 1

LINE OUT 1

AUDIO

RF OUT

VIDEO

DVD/VCR shared AUDIO output jacks

VCR AUDIO input jacks

ANTENNA IN (antena

or cable input)

COMPONENT VIDEO output jacks

DVD S-VIDEO output jack

DVD AUDIO output jacks

COMPONENT

(CB)

(CR)

DVD OUT

LINE OUT 2

S-VIDEO

DIGITAL

AUDIO

LINE IN 1

AUDIO

VIDEO

VCR

ANTENNA IN

RF OUT

ANTENNA OUT

DVD/VCR

LINE OUT 1

AUDIO

VIDEO

VCR VIDEO input jack

DVD/VCR shared VIDEO output jack

Basic Connection

Caution:

• Be sure to turn off the Product and equipment to be connected before connecting.

• Read through the operation manual for the equipment to be connected.

•

Be sure that the colours of the jacks and plugs match up when using a VIDEO/AUDIO cable

• Be sure to keep the Product connection cables separate from the TV antenna cable when you install the Product, because it may cause electrical interference when you are watching television programmes.

Connecting to ANTENNA IN/RF OUT

The connection method differs depending on the type of TV.

This Product

To antenna input jack

COMPONENT

(CB)

(CR)

DVD OUT

LINE OUT 2

S-VIDEO

RF cable

(Supplied)

To ANTENNA IN jack

DIGITAL

AUDIO

To RF OUT jack

DVD/VCR LINE OUT 1

AUDIO

VIDEO

LINE IN 1

AUDIO

VIDEO

VCR

ANTENNA IN

RF OUT

Antenna cable

Connecting a TV Equipped with VIDEO/AUDIO Input Jacks

This Product

VCR

LINE IN 1

AUDIO

VIDEO

COMPONENT

(CB)

(CR)

DVD OUT

LINE OUT 2

S-VIDEO

DIGITAL

AUDIO

DVD/VCR LINE OUT 1

(Red)

AUDIO

(White) (Yellow)

VIDEO

Basic Connection

ANTENNA IN

RF OUT

CONNECTION AND

INITIAL SETTINGS

Required cable

VIDEO/AUDIO cable

(supplied)

To DVD/VCR shared VIDEO/AUDIO out jacks

VIDEO/AUDIO cable (supplied)

Yellow

White (L)

Red (R)

Jack and Plug Colours

Video: Yellow

Yellow White (L) Red (R)

(White)

(Red) (Yellow)

To VIDEO/AUDIO

input jacks Audio Left: White Audio Right: Red

VIDEO

AUDIO

TV (with external input jacks)

Y ou will not be able to hear all of the sound being output by the Product if you use the supplied VIDEO/AUDIO

cable to a monaural TV that has only one AUDIO input jack.

• Make sure that colours of the jacks and plugs match up when connecting the cable.

• Connect the Product directly to the TV. If you attempt to view video on a TV connected via a VCR, the copy protection

function will scramble the picture.

• If you want to listen to the audio through audio equipment, connect only the VIDEO cable to the TV.

Using the Component Colour (Y, P

) and P

)) Output Jacks

Colour Output Jacks (Y, P P

(CR)):

(CB) and

Some TVs and monitors are equipped with input jacks for the component colour signals (Y, P

(CB) and PR (CR)). By connect-

ing these input jacks to the corresponding output jacks on the Product, you can enjoy higher quality playback images. If you are using a TV or monitor equipped with Y, P

(CB) and PR (CR) jacks, use these

jacks rather than the S-VIDEO OUT jack.

COMPONENT

(CB)

(CR)

DVD OUT

LINE OUT 2

S-VIDEO

DIGITAL

AUDIO

DVD/VCR LINE OUT 1

AUDIO

VIDEO

VCR

ANTENNA IN

LINE IN 1

AUDIO

RF OUT

VIDEO

DVD Audio Connections

Connecting a TV Equipped with S-VIDEO Input Jacks

When you want to achieve a better video image by connecting a TV equipped with an S-VIDEO input connector to the Product, you should use an S-VIDEO cable (commercially available) to connect the TV to the Product.

Connecting to Audio Equipment

Connecting the Product to audio equipment provides normal stereo sound plus powerful stereo sound enhanced by Dolby Digital (5.1 channel), DTS, and MPEG Audio.

Playing 2 channel audio

■ Analogue Connection

This Product

Required cables

AUDIO cable (commercially available)

White (L)

Red (R)

S-VIDEO cable (commercially available)

DVD OUT

COMPONENT

(CB)

(CR)

LINE OUT 2

S-VIDEO cable (commercially available)

AUDIO cable (commercially available)

DIGITAL

AUDIO

S-VIDEO

AUDIO

To S-VIDEO OUT jack

To AUDIO OUT jacks

(Red)

(White)

DVD/VCR

LINE OUT 1

R AUDIO

VIDEO

LINE IN 1

AUDIO

VIDEO

White (L) Red (R)

VCR

ANTENNA IN

RF OUT

Jack and Plug Colours

Audio Left: White Audio Right: Red

To S-VIDEO input jack

S-VIDEO

INPUT

To amplifier audio input jacks

ANALOG INPUT

(White)

(Red)

Amplifier of stereo system, etc.

TV (with external input jacks)

If the Product is set to OPERATE ON, the DVD signals will be output from the DVD OUT jacks at all times.

(The DVD signals will be output from the DVD OUT jacks also when using the VCR.)

DVD Audio Connections

Playing Dolby Digital (5.1 channel), DTS or MPEG audio

Connecting an amplifier with a Dolby Digital/DTS/MPEG Audio digital surround processor or a Dolby Digital/ DTS/MPEG Audio surround processor to your Product’s coaxial digital jack provides richer and more powerful audio play.

■ Connection to a processor or amplifier with a coaxial digital input jack

You can make this connection using a coaxial digital

This Product

cable

To coaxial digital input jack

COMPONENT

(CB)

(CR)

Required cable

Coaxial digital cable (commercially available)

DVD OUT

LINE OUT 2

S-VIDEO

DIGITAL

AUDIO

DVD/VCR LINE OUT 1

R AUDIO

VIDEO

LINE IN 1

AUDIO

VIDEO

VCR

ANTENNA IN

RF OUT

To coaxial DIGITAL OUT jack

Coaxial digital cable (commercially available)

DIGITAL IN

COAXIAL

Audio equipment

Digital Connection to an MD to Record a CD

Some Audio CDs and VIDEO CDs have a short silent section between musical tracks. When sound from discs such as these is digitally recorded by connecting the Product directly to a digital recorder (such as an MD player), the music may be recorded continuously and track numbers may be lost.

■ Digital Connection to Audio Equipment or MD Player without a Dolby Digital Decoder

• Audio CD or VIDEO CD Play the disc as you normally would, with the audio mode set to “L+R” (see page 89). With a digital connection, audio of a disc recorded with DTS sounds abnormal in this case.

• DVD With a digital connection, audio cannot be produced from a DVD recorded with Dolby Digital (5.1 channel), Dolby Surround (Pro Logic), DTS or MPEG Audio, so you should use an analogue connection to play such discs. Discs with linear PCM audio should play normally.

• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial

digital input jack.

Preparations Before Using the Product

Preparing to Watch a VCR or a DVD

1 Turn on the TV and switch the TV channel to the external

“VIDEO” or “AV” channel connected to the DVD/VCR shared output jacks.

2 Press OPERATE.

• The product is turned on.

3 Press VCR/DVD SELECTOR on the remote control to switch to

the “VCR” mode or “DVD” mode.

• The VCR/DVD SELECTOR on the product lights up in orange for “VCR” or green for “DVD”.

OPERATE

AV 2 IN

VIDEO

OPERATE

PLAY STOP

REW

EJECT/STOP

PLAY/×2

REC

)

L(MONO

AUDIO-R

VCR/DVD SELECTOR

TIMER

DVD

VCR

VCR/DVD

SELECTOR

OPEN/CLOSE

VCR/DVD SELECTOR

• Each time VCR/DVD SELECTOR is pressed, the mode changes between “VCR” mode and “DVD” mode.

• The mode can be switched by pressing the VCR/DVD SELECTOR on the product.

4 Move the VCR/DVD CHANGE Switch on the Remote to either

“VCR” or “DVD”.

VCR DVD

The VCR functions on the Remote will now take priority.

VCR DVD

The DVD functions on the Remote will now take priority.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

SELECTOR

SCREEN

PROG/

FUNCTION

ANGLE

REPEAT

CONTROL

TITLE

CLEAR

RETURN

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

TAPE

SKIP

SPEED

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

EJECT

VCR MENU DVD SETUP

OPEN/ CLOSE

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

SELECTOR

SCREEN

PROG/

FUNCTION

ANGLE

REPEAT

CONTROL

TITLE

CLEAR

RETURN

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

TAPE

SKIP

SPEED

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

EJECT

VCR MENU DVD SETUP

OPEN/ CLOSE

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

Adjusting the Video Channel

To view the output of your Product on the television screen, you must select an unused channel on your TV and tune it to the output of your Product (see Table 1 for factory preset to UHF Channel).

1 Make sure both Products (TV and this Product) are connected

(power cord) to the power outlet.

2 T urn on your TV.

3 Select an unused channel on your TV.

4 Set the power on the Product to of f. (If the Product is ON, press

OPERATE to turn off the power.)

5 Keep pressing VCR MENU for more than two seconds to light up

the UHF Channel (see Table 1) on the VCR Front Panel display .

Table 1

South East Asia, Hong Kong

Ex.

Australia

Factory Preset UHF Channel

60 37

6 Adjust the tuning of the selected TV channel until the RF pattern

appears on your TV screen. (Refer to your Operation Manual for tuning procedures.)

SYSTEM I B/G D/K

(RF pattern)

DV-NC70W and DV-NC70 only

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

SYSTEM B/G D/K

(RF pattern)

DV-NC70X only

VCR/DVD COMBINATION

Adjusting the Video Channel

7 Press

\ /

| to select the RF output system that corresponds to

your TV by referring to the chart shown to the below, and press SET.

I,B/G,D/K (RF system) Hong Kong China, Russia

Ex.

D/K

South East Asia Australia

B/G

New Zealand

8 Press OPERATE to turn on the power of the Product. Select any

channel on the VCR tuner. If a picture appears and sound can be heard, then the RF output system is correctly set. If a picture appears but no sound can be heard, then perform step 7 above to select another RF output system.

• Make sure the sound is not muted when checking the RF output system.

• It is not necessary to change the system to RF system “M”. The Product will automatically detect and change the RF system to “M” when receiving the NTSC signal.

• If picture interference appears on the TV screen in step 6 above, you can change the video channel (RF output channel from the Product to TV) with the following procedure. If UHF Channel (see Table 1) is an active broadcast channel in your area, manually select a different channel (UHF 21 to UHF 69) (see below) and then retune your TV as above.

1 Press OPERATE to turn off the power. 2 Keep pressing VCR MENU for more than two seconds to light up

the UHF Channel (see Table 1) on the VCR Front Panel display.

3 Press ' / " on the Remote to manually select an unused channel

for use as the video channel.

4 Perform steps 6 to 7 above using the newly selected video

channel.

5 Repeat steps 3–4 to select the optimal video channel.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

Auto Tuning System

This Product is equipped with an Auto Tuning System to provide easier set up of the Product. After following the instructions for “Basic Connection” on pages 14 and 15 and “Adjusting the Video Channel” on page 19, turn on your TV, press OPERATE to turn on the Product, and select the video channel. The Product will automatically display the setting screens as shown below.

LANGUAGE

setting screen

Press SET. (Manual operation)

SYSTEM

setting screen

Press SET. (Manual operation)

AUT OMATIC TUNING

screen

Press VCR MENU to cancel the next step.

CLOCK

setting screen

Press SET. (Manual operation)

Normal screen appears.

• If the Language selection and Auto Tuning have already been performed, the Clock setting screen will first appear. To reset all VCR settings and perform the Auto Tuning from the Language setting screen, see page 37. (Perform “VCR-RESET”)

Selection of language to be used for the On Screen Display. (See page 37.)

Selection of broadcast system(SYSTEM) (I, B/G, D/K or M) that correspond with your area. (See page 28, step 3.)

Setting and sorting the channels for your area. (See page 28.)

Setting the present time. (See page 35.)

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

VCR Setup

VCR Setup .................................................................................... 24

Menu Screen............................................................................... 24

Mode Selection ........................................................................... 25

Setting the Channels................................................................... 27

Auto Tuning................................................................................. 28

Manual Tuning ............................................................................ 30

Channel Skip/Cancelling Skip..................................................... 32

Channel Skip............................................................................ 32

Cancelling Skip ........................................................................ 34

Setting the Clock......................................................................... 35

Initial Setting of Clock .............................................................. 35

Changing the Clock Setting ..................................................... 36

Setting the Language.................................................................. 37

VCR-RESET ............................................................................ 37

Initial Setting of Language ....................................................... 37

Changing Language................................................................. 37

VCR Display Information............................................................. 38

How to Display Indicators ........................................................... 38

VCR Front Panel Display ............................................................ 38

VCR SETUP

23GB23

23Web-site:www.sharp.co.uk/support Help line:08705 274277 (office hours)

VCR Setup

Menu Screen

The menu screen is a home screen used to select various screen functions. A sub-menu will appear once you select an item for the menu. See the following pages for details on each menu procedure.

• The word “G-CODE” will only appear on menu screen for DV-NC70W which has the G-CODE system.

MENU item list

Main Menu

G-CODE

TIMER

MODE

Only for DV-NC70W

COLOUR [AUTO/PAL/MESECAM/NTSC]

NTSC [3.58/4.43/PAL TV] BLUE BACK [AUTO/OFF] AUTO RENTAL [ON/OFF] REPEAT [ON/OFF] NICAM [AUTO/OFF] S. PICTURE [ON/OFF]

Menu Screen

G-CODE

TIMER MODE CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

Only for DV-NC70W

CHANNEL PRESET

CLOCK

LANGUAGE

AUTO MANUAL

ENGLISH

• Numbers in refer to the pages where the setting procedures are described.

PRESET CH SYSTEM CHANNEL

FINE TUNING SKIP [ON/OFF]

Mode Selection

You can set the basic functions listed in the table below on the MODE selection screen.

VCR Setup

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

1 Press VCR MENU to display the menu screen. 2 Select “MODE” with ' / " and then press SET to confirm.

MENU G-CODE TIMER

MODE

CHANNEL PRESET CLOCK LANGUAGE

:SELECT SET:ENTER MENU:EXIT

3 Set “NTSC” to “3.58”, “4.43” or “PAL TV” with

Then press ".

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

NTSC 3.58 ..... When using NTSC 3.58 TV system.

(Input signal: NTSC 3.58)

NTSC 4.43 ..... When using NTSC 4.43 TV system.

(Input signal: NTSC 4.43)

PAL TV........... When using PAL TV system.

(Input signal: NTSC 4.43)

\ /

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR Setup

4 Set “NICAM” to “AUTO” or “OFF” with

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

\ /

|. Then press ".

AUTO............. Usually select “AUTO”.

OFF................ Select “OFF” when your TV does not have good

NICAM signal reception and a lot of noise is heard when the AUTO mode is set. (Selecting “OFF” will change it to normal audio signal reception.)

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

G-CODE

PROG

• You can change the COLOUR, BLUE BACK, AUTO RENTAL, REPEAT and S.PICTURE settings the same way (See pages 55, 56, 58 and 59).

5 Press SET to enter.

• The screen returns to normal.

• If you press VCR MENU to exit the mode selection screen in Step 4,

the data will not be stored. Be sure to press SET to store the data.

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

VCR Setup

Setting the Channels

Your Product can receive VHF channels 1A to E12 (US AIR 2 to 13), CATV/HYPER channels S1 to S41 and UHF channels E21 to E69 (US AIR 14 to 78). Your Product has 84 programmable channel positions, each of which can be set to any of the broadcast and CATV/HYPER channels.

• Channel positions 13 through 83 will not be displayed when selected. These channel positions have been set at the factory to be skipped.

• To view a skipped channel position, tune that position to a broadcast CATV/HYPER channel, or cancel the channel skip function for that position.

BROADCAST TV CHANNEL

VCR

CHANNEL

000 001 002 003 004 005 006 007 008 009 010 011 11 012

021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075

SOUTH

1A E-2 E-3 E-4 E-5 E-6 E-7 E-8 E-9

E-10 E-11 E-12

E-21 E-22 E-23 E-24 E-25 E-26 E-27 E-28 E-29 E-30 E-31 E-32 E-33 E-34 E-35 E-36 E-37 E-38 E-39 E-40 E-41 E-42 E-43 E-44 E-45 E-46 E-47 E-48 E-49 E-50 E-51 E-52 E-53 E-54 E-55 E-56 E-57 E-58 E-59 E-60 E-61 E-62 E-63 E-64 E-65 E-66 E-67 E-68 E-69

CHINA

EAST ASIA

C-1 C-2 C-3 C-7 C-8 C-9

C-10 C-11 C-12

Z-8

C-13 C-14 C-15 C-16 C-17 C-18 C-19 C-20 C-21 C-22 C-23 C-24

C-25 C-26 C-27 C-28 C-29 C-30

100

C-31

101

C-32

102

C-33

104

C-34

105

C-35

106

C-36

108

C-37

109

C-38

110

C-39

112

C-40

113

C-41

114

C-42

116

C-43

117

C-44

118

C-45

120

C-46

121

C-47

122

C-48

124

C-49

125 C-50 C-51 C-52 C-53 C-54 C-55 C-56 C-57

103

112

122

CATV

02 03 07 08 09 10 12 13 23 24

67 68 69 71 72 73 75 76 77 79 80 81 83 84 85 87 88 89 91 92 93

79 89

AUSTRALIA

0 01 02 03 04 05 06 07 08 09 10

28 29 30 31 32 33 34 35 36 37 38

67 68 69

NEW ZEALAND

01 02 03 04 05 06 07 08 09 10

BROADCAST TV CHANNEL BROADCAST TV CHANNEL

SOUTH

EAST ASIA

VCR

CHANNEL

081 082 083 084 085 5A 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148

S-1 S-2 S-3 S-4 S-5 S-6 S-7 S-8

S-9 S-10 S-11 S-12 S-13 S-14 S-15 S-16 S-17 S-18 S-19 S-20 S-21 S-22 S-23 S-24 S-25 S-26 S-27 S-28 S-29 S-30 S-31 S-32 S-33 S-34 S-35 S-36 S-37 S-38 S-39 S-40 S-41

X Y

Z Z+1 Z+2

Z-1 Z-2 Z-3 Z-4

Z-5 Z-6 Z-7

Z-8

Z-9 Z-10 Z-11

Z-12 Z-13 Z-14 Z-15 Z-16 Z-17 Z-18 Z-19 Z-20 Z-21 Z-22 Z-23 Z-24 Z-25 Z-26 Z-27 Z-28 Z-29 Z-30 Z-31 Z-32 Z-33 Z-34 Z-35 Z-36 Z-37

C-4 C-5

Z-2

C-3

C-4

Z-5

CHINA

CATV

97 99 14 15 16 17 18 20 21 22 25 26 28 29 30 31 32 33 35 36 37 39 40 41 43 44 45 47 48 49 51 52 53 55 56 57 59 60 61 63 64 04 05 06 95 96 29

05 97 98 99 18 19 19 20 09 10 11 25 26 27 32 33 34 37 38

AUSTRALIA

NEW ZEALAND

149 150 151 152 153 154 155 156 157 158 159 160

161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198

VCR

SOUTH

CHANNEL

EAST ASIA

CHINA

Z-12

100 102 104 106 107 108 110 111 114 115 116 118 119 120 123 124

AUSTRALIA

CATV

NEW ZEALAND

41 42 45 46 49 50 53 54 57 58 61 62

66 67 69 70 71 73 74 75 77 78 81 82 83 85 86 87 90 91 93 94

VCR Setup

Auto Tuning

Preparation

•

Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

• Ensure the Video channel is selected on the TV.

1 Press VCR MENU. Press ' / " to select “CHANNEL PRESET”.

Press SET to confirm.

DV- NC70W DV- NC70

DV- NC70X

G-CODE

PROG

MENU G-CODE TIMER MODE

CHANNEL PRESET

CLOCK LANGUAGE

:SELECT SET:ENTER MENU:EXIT

2 Press ' /" to select “AUTO”. Press SET to confirm.

CHANNEL PRESET

AUTO

MANUAL

:SELECT SET:ENTER MENU:EXIT

3 Press

confirm. Select the broadcast system used for areas where I,

B/G, D/K, M reception is necessary. (For DV-NC70X, only B/G

and D/K will appear on the screen.)

\ /

| to select the SYSTEM you desire. Press SET to

AUTOMATIC TUNING SYSTEM I B/G D/K M

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

:CHANGE SET:ENTER MENU:EXIT

I,B/G,D/K,M (Receiving system) Hong Kong China, Russia

D/K

South East Asia,

Ex.

Australia, New

B/G Zealand U.S.A., Japan, Philippine

• If the broadcast signal system does not match the Product receiving system, tuning is not possible.

4 The channel display on the TV screen will continue through all of

the channels and when finished, the TV screen will return to the MOVE (channel sort) screen. The bar display indicates the estimated amount of channels tuned.

VCR/DVD COMBINATION

5 To change the order of tuned-in broadcast, press ' /"/

\ /

to select the channel to be moved. Press SET to confirm .

“SELECTED: CH078” will appear.

MOVE 1/5 1CH002 7 13 2CH003 8 14 3CH004 9 15 4CH075 10 16 5CH078 11 17 6 12 18 SELECTED :CH078 :SELECT SET:ENTER MENU:EXIT

6 Press ' /"/

| |

\ /

| to select the new position for the channel.

| |

Then, press SET to confirm.

“SELECTED: CH078” will disappear.

MOVE 1/5 1CH078 7 13 2CH002 8 14 3CH003 9 15 4CH004 10 16 5CH075 11 17 6 12 18

:SELECT SET:ENTER MENU:EXIT

7 To move additional channels, repeat steps 5 and 6. 8 When the channels have been sorted into the desired order,

press VCR MENU to return to the normal screen.

• If additional unwanted channels are found, refer to page 32 to skip them.

• If some channels are unable to be found, refer to “Manual Tuning” the

next page.

VCR Setup

G-CODE

PROG

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

VCR/DVD COMBINATION

VCR Setup

Manual Tuning

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

• Ensure the Video channel is selected on the TV .

Example: Tuning Channel Position 48 to Broadcast TV Channel E7 (VCR CHANNEL 007 for system I area.)

1 Press VCR MENU. Press ' / " to select “CHANNEL PRESET”

and press SET to confirm.

MENU G-CODE TIMER MODE

CHANNEL PRESET

CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

2 Press ' / " to select “MANUAL” and press SET to confirm.

CHANNEL PRESET AUTO

MANUAL

:SELECT SET:ENTER MENU:EXIT

3 Select the preset channel position number 48 with the number

buttons (0 to 9) or

\ /

| and press ".

PRESET CH 48 SYSTEM I B/G D/K M CHANNEL 002 FINE TUNING SKIP ON OFF

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

:SELECT :CHANGE SET:ENTER MENU:EXIT

4 Press

| |

\ /

| to select the “SYSTEM” you desire and press ".

| |

(For DV-NC-70X, only B/G and D/K will appear on the screen.)

PRESET CH 48 SYSTEM I B/G D/K M CHANNEL 002 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

5 Press the number buttons (0 to 9) or

\ /

| until you see the

desired broadcast channel E7 (VCR CHANNEL 007) on your TV and press ".

VCR Setup

PRESET CH 48 SYSTEM I B/G D/K M CHANNEL 007 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

6 For fine tuning, press

| |

\ /

| until the broadcast channel comes in

| |

clearly on your TV.

PRESET CH 48 SYSTEM I B/G D/K M

CHANNEL 007 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

7 To check that the broadcast channel you tuned the Product to is

VHF E7, select channel 7 using the TV tuner.

8 Select the video channel on your TV again.

• If the channel you tuned the Product to and the one on the TV do not match, repeat steps 5 through 7.

9 Press SET. (This will set channel position 48 in memory and

return to channel position 49 for tuning.)

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

10 If you want to set additional channels, repeat steps 3 through 9.

11 Press VCR MENU to return to the normal screen.

• Use Auto Tuning normally for presetting.

1 Auto tuning may not be able to preset some broadcasts. Use manual tuning to preset. 2 The same broadcast may be preset more than once. Select the channel with the clearer broadcast.

3 After auto tuning is completed, confirm the preset channels in

order.

If no sound can be heard from any of the preset channels, reset the

SYSTEM (I, B/G, D/K, M) with manual tuning.

VCR/DVD COMBINATION

VCR Setup

Channel Skip/Cancelling Skip Channel Skip

If there are channel positions that are not preset, you can skip them with the following procedure.

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

Example: Skip channel position 12.

1 Press VCR MENU. The menu screen will appear. Press ' / " to

select “CHANNEL PRESET” and press SET to confirm.

MENU G-CODE TIMER MODE

CHANNEL PRESET

CLOCK LANGUAGE

:SELECT SET:ENTER MENU:EXIT

2 Press ' / " to select “MANUAL”. Press SET to confirm.

CHANNEL PRESET AUTO

MANUAL

:SELECT SET:ENTER MENU:EXIT

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

3 Set the channel position you wish to skip with

buttons (0 to 9).

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

4 Press ' / " to select “SKIP”.

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

\ /

| or number

VCR/DVD COMBINATION

5 Press

\ /

| to set “ON” and press SET to confirm.

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

6 If you wish to set more channels to be skipped, repeat steps 3

through 5.

7 Press VCR MENU to return to the normal screen.

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

VCR Setup

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

• When making channel inputs with the number buttons (0 to 9), first

select the one figure input or two figures input using the -/-- button on the Remote.

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

VCR Setup

Cancelling Skip

Example: Reset channel position 12.

1 Follow the steps 1 and 2 from “Channel Skip” on page 32.

2 Select the channel position you wish to unskip with

\ /

| or

number buttons (0 to 9).

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

3 Press ' / " to select “SKIP”.

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFFF

:SELECT :CHANGE SET:ENTER MENU:EXIT

4 Press

\ /

| to set “OFF” and press SET to confirm.

PRESET CH 12 SYSTEM I B/G D/K M CHANNEL 012 FINE TUNING SKIP ON OFF

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

:SELECT :CHANGE SET:ENTER MENU:EXIT

5 If you wish to unskip more channels, repeat steps 2 through 4. 6 Press VCR MENU to return to the normal screen.

VCR/DVD COMBINATION

Setting the Clock

When you use the Product for the first time or after a power failure of more than 60 minutes the clock has to be reset. Apply power to the Product to switch it on. Then perform the following procedure.

Initial Setting of Clock

1 First set the language and system setting. (See page 21.) Then

press SET.

2 Press ' / " to select whether the clock should show 12-hour AM/

PM time or 24-hour time and press

CLOCK

MODE TIME DATE YEAR

24H 0:00 1/01 00

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

VCR Setup

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

G-CODE

PROG

MODE:24H/12H :SELECT :CHANGE SET:ENTER MENU:EXIT

3 Set the present time with the number buttons (0 to 9) or ' / " on

the Remote and press “minute”. If there is only one “hour” or one “minute” digit, enter a 0 first.)

• If 12H mode is selected, set the AM or PM indicator.

|. (First set the “hour” digits and the

CLOCK

MODE TIME DATE YEAR 24H 10:28 1/01 00

:SELECT :CHANGE SET:ENTER MENU:EXIT

4 Set the date with the number buttons (0 to 9) or ' / " on the

Remote and press “month”. If there is only one “day” or one “month” digit, enter a 0 first.)

|. (First set the “day” digits and then the

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

CLOCK

MODE TIME DATE YEAR 24H 10:28 15/12 00

DATE :DAY/MONTH :SELECT :CHANGE SET:ENTER MENU:EXIT

VCR Setup

5 Set the year digits with the number buttons (0 to 9) or ' / " on

the Remote. (If there is only one “year” digit, enter a 0 first.)

CLOCK

MODE TIME DATE YEAR 24H 10:28 15/12 00

SELECT : CHANGE:

ENTER :SET EXIT :MENU

6 Press SET to return to the normal screen.

Changing the Clock Setting

1 If the clock has already been set previously and you want to

change it, select “CLOCK” from the MENU, and then follow the steps 1 to 6 from “Initial Setting of Clock” on pages 35 and 36.

2 Press VCR MENU. Press ' / " to select “CLOCK” and press

SET to confirm. Press VCR MENU to return to the normal screen.

MENU G-CODE TIMER MODE CHANNEL PRESET

CLOCK

LANGUAGE

:SELECT SET:ENTER MENU:EXIT

• If the precise clock time is required (within a second), do not press

SET until the exact start of the minute after setting the year (after completing step 5). The clock will start operation as soon as SET is pressed.

• If you prefer the clock display time in the 12-hour AM/PM system,

select “12H” in step 2. In this case, when you set the present time using the number buttons, first press AM/PM on the Remote to select AM or PM, and then set the present time.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

Setting the Language

This Product is factory preset to display the LANGUAGE setting screen after VCR MENU is pressed when the Product is operated for the first time. In some cases, the retailer may have already set the language, and the CLOCK setting screen will appear after VCR

MENU is pressed. To reset the Product, perform the following steps.

VCR-RESET

1 Press OPERATE to POWER OFF on the Product. 2 Press OPERATE to POWER ON on the Product. 3 Press VCR MENU and CH " on the Remote at the same time

for five seconds.

(The LANGUAGE setting screen should appear.)

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

VCR Setup

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

• When the Product is reset, all channel settings, guide channel setting

for the G-CODE system and timer setting will be cancelled.

Initial Setting of Language

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

1 Press ' / " to select the language and press SET to confirm.

LANGUAGE

ENGLISH

Changing Language

If the language has already been set previously and you want to change it, follow the steps below.

1 Press VCR MENU. Press ' / " to select “LANGUAGE ” and

press SET to confirm.

MENU G-CODE TIMER MODE CHANNEL PRESET CLOCK

LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

DVD

VCR

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

2 Select the language with ' / " and press SET to confirm.

LANGUAGE

ENGLISH

3 Press VCR MENU to return to the normal screen.

VCR Display Information

The tape counter and VCR mode can be shown on the screen while you are playing back a tape or watching a broadcast on the video channel.

PLAY, X2 VSF, FF VSR, REW STOP, CASSETTE IN F ADV. SLOW STILL REC REC PAUSE

Operating mode

S. PICTURE

(Sharp Super Picture)

Simple Recording timer

Tape Speed

Clock display

Calendar display

How to Display Indicators

1 Turn on your TV and select the video channel. 2 Press OPERATE to turn on the Product. Mode indicators are displayed in the AUTO display screen. 3 Each time ON SCREEN is pressed, the screen changes as follows:

AUTO Display → FULL Display → Counter Display → Display OFF

AUTO DISPLA Y

When an operation button, number buttons or CH ' / " is pressed, the current mode or the number of the channel will be displayed in the upper section of the TV screen for about 3 seconds.

Display example

2 S.PICTURE ON NICAM I/ SP STOP 11:30 L R

REPEAT 12:30 19 21/08 00 0:00.00

Real time tape counter

DPSS

Programme channel position

Multiplex sound indicator

: stereo)

( Audio Output indicator

Repeat display

DPSS

• When you record a video signal output from this Product on another VCR, press ON SCREEN to select Display Off. (If

the mode indicator is displayed on the screen, it is also recorded on the tape.)

VCR Front Panel Display

Each time DISPLAY on the Remote is pressed, the display changes in the following way. (However, the follow- ing is the case when the clock time is set and displayed in the 12-hour system.)

Channel setting mode → Tape counter mode → Clock mode

• Channel setting mode ..

• Tape counter mode ....... The current tape position will be displayed.

• Clock mode.................... The current time will be displayed.

The meaning of the main indicators is shown below. (This list does not include all indicators.)

Display Examples

Rotate

Rotate rapidly

Rotate

The number of the channel will be displayed. It does not display during playback.

slowly

Cassette-In

Indicator

Playback

Rewind,

Video Search Rewind

Fast forward,

Video Search Forward

Record

Rec Pause

Slow, Still,

Frame Advance

When AC power cord

is first plugged in

Stop

LINE IN 1/2

• Tape counter is displayed during playback, fast forward or rewind operation.

• When the power is turned off, the clock is displayed and the VCR Front Panel Display Becomes darker.

• The display will return to the original mode (counter or clock display) 3 seconds after the VCR enters the operation

mode.

DVD Setup

DVD Setup ....................................................................................... 40

About the SETUP Screen .............................................................. 40

TV MODE Setting .......................................................................... 41

P ARENTAL Level Setting ............................................................... 42

AUDIO Setting ............................................................................... 44

Setting the COMPRESSION (Dolby Digital output level)............ 44

Setting the DOLBY DIGITAL ....................................................... 45

Setting the MPEG ....................................................................... 46

Setting the CINEMA VOICE........................................................ 46

DISC LANGUAGE Setting ............................................................. 47

Setting SUBTITLE, AUDIO and MENU languages..................... 47

Selecting languages from OTHER.............................................. 48

DVD Display Information................................................................ 49

Operation Mode Indicators............................................................. 49

Language Code List for Disc Language ....................................... 50

DVD SETUP

DVD Setup

About the SETUP Screen

This section describes how to specify various basic settings using the SETUP screen. The list below shows all the items you can set and adjust. See the following pages for details on each setup procedure.

• The setting procedures described on the following pages are available only in STOP mode.

• The OSD (On Screen Display) screens used in this Operation Manual are purely for the purposes of explanation. The actual displays (set displays) may differ slightly from what is shown here.

Important!

• When you set the language to be used in the OSD, changing the

mode to “VCR” and select “LANGUAGE” in the menu screen. See OSD Language Setting on page 37 for details.

Setup item list

Main Menu

TV MODE

• Specifies the setting for the type of TV connected and the playback format for wide-screen video material.

4 : 3 4 : 3

16 : 9

PS LB

(Example) TV MODE

TV MODE

4:3

16:9

SELECT

ENTER

RETURN

• Numbers in refer to the pages where the setting

PARENTAL [1 to 8 (ON)/OFF]/Selecting the Country Code

• Sets or changes the parental level (1 to 8).

• Used to set or change the password used to

prevent the parental level from being changed too easily.

• See page 43 for Country Code.

AUDIO

• Use this setting for increasing the average volume of Dolby Digital audio when playing a DVD.

• Use this setting for specifying either “BITSTREAM” or “D-PCM” as the digital type.

DISC LANGUAGE

• Use this setting for selecting languages of subtitle, audio track and disc menu recorded on a disc.

OSD LANGUAGE SETUP

• Use this setting for selecting OSD languages.

procedures are described.

COMPRESSION [ON/OFF]

DIGITAL

MPEG

CINEMA VOICE[ON/OFF]

AUDIO

SUB TITLE

MENU ENGLISH

ESPAÑOL FRANÇAIS

BITSTREAM D-PCM BITSTREAM PCM

ENGLISH SPANISH

FRENCH ITALIAN GERMAN CHINESE SWEDISH DUTCH OTHER

Languages you can select are same as above.

DVD Setup

TV MODE Setting

Preparation

• See Preparing to Watch a DVD on page 18.

1 While this product is stopped, press DVD SETUP to display the

SETUP screen.

2 Use ' or " to select the “ TV MODE”.

TV MODE PARENTAL LEVEL 8 AUDIO DISC LANGUAGE

ENTER

SELECT ENTER

4:3

RETURN

3 Press ENTER to display the items you can select.

4:3

4 Use ' or " to select

(Example) Selecting

TV MODE

4:3

16:9

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REV FWD

REC

TAPE

SPEED

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

PLAY

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

SELECT

ENTER

4:3

•

— (Pan & Scan mode): When wide-screen video

RETURN

material is played, this mode clips the right and left sides of the image so that it can be viewed on a conventional TV screen.

• Some wide-screen DVDs that do not permit Pan & Scan mode playback are automatically played in letterbox mode (black bands top and bottom).

4:3

•

— (Letterbox mode): When wide-screen video material is played in this mode on a conventional TV screen, black bands appear at the top and bottom of the screen.

16:9

— (Wide-screen TV): This is the correct mode for playing

•

wide-screen videos on a wide-screen TV.

• You must also set the screen mode on your wide-screen TV to

“FULL”.

5 Press ENTER to confirm the “TV MODE” setting. 6 If you want to complete the settings here, press RETURN to exit

the SETUP screen and return to the normal screen.

• If you intend to go on and specify other settings (PARENTAL, AUDIO or DISC LANGUAGE), press ' or " to display other SETUP screen without pressing RETURN.

VCR/DVD COMBINATION

Cut off when a wide-screen video image is played.

The actual appearance of the image depends on the screen mode setting of your widescreen TV .

DVD Setup

PARENTAL Level Setting

Certain discs come preset with country codes and parental level settings defined for particular countries. Discs equipped with the parental lock function are rated according to their content. The rated content allowed by a parental lock level and the way a DVD can be controlled vary from disc to disc. Some discs, for example, may let you edit out scenes and replace them with scenes suitable for children. You can also use the parental lock to completely disable playback of the DVD.

Preparation

• See Preparing to use DVD on page 78.

1 Press DVD SETUP to display the SETUP screen.

OPERATE

DISPLAY

FUNCTION CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

2 Use ' or " to select the “ PARENTAL” and then press

ENTER.

• The password specification and verification screen appears. For DV-NC70X model, the par ental country code is “Australia”.

PARENTAL PASSWORD PASSWORD

LEVEL OFF CODE CHINA

• If you have already set your password,

ENTER

????

SELECT

RETURN

(password

verification display) appears.

3 Use the number buttons (0 to 9) to enter a 4-digit password.

P ASSWORD : 1 2 3 4

• Enter the numbers slowly as each number is stored separately.

• If you enter the wrong number three times in succession, the normal

screen reappears.

If you forget your password, you can erase your current password by pressing ËSTOP four times.

Displayed when “1234” is being entered as the

password.

CLEAR

RETURN

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

ZERO BACK

VCR DVDAM/PM

PAUSE/STILL

SLOW

4 The cursor is moved to “LEVEL” and then press ENTER.

PARENTAL

LEVEL 1 LEVEL 5 LEVEL 2 LEVEL 6 LEVEL 3 LEVEL 7 LEVEL 4 LEVEL 8

OFF

ENTER

SELECT

RETURN

5 Press ', ", | or \ to select the desired parental level and

then press ENTER. (Example) Selecting “LEVEL 8”

DVD Setup

DV- NC70W DV- NC70

DV- NC70X

G-CODE

PROG

PARENTAL PASSWORD

PASSWORD LEVEL 8 CODE CHINA

----

• Level 1: for most restricted viewing → Level 8: for adult viewing (The smaller the number, the greater the level of restriction.)

• When “PARENTAL” is set to “OFF”, DVD discs can be played back regardless of the parental level.

The parental level set up for CHINA is prepared for future use. As for the set up of an appropriate level, please check the level when you purchase your DVD disc equipped with the parental feature.

6 Press " to select “CODE” and then press ENTER.

PARENTAL CODE USA FRANCE

CANADA UK JAPAN ITALY GERMANY SPAIN

ENTER

SELECT

RETURN

7 Press ', ", | or \ to select the desired country code and then

press ENTER.

• If you want to go to next page, select the country code displayed at the bottom, and then press ".

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR RETURN

REV FWD

REC

TAPE

SPEED

SELECTOR

SCREEN

PROG/

ANGLE

REPEAT

INPUT SELECT

PLAY

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

PARENTAL PASSWORD

PASSWORD LEVEL 8 CODE CHINA

----

8 Press RETURN to return to the SETUP screen.

• If you want to go on and specify the other settings, use ' or " to display other SETUP screen. However, press RETURN if

you want to exit the SETUP screen.

Important!

• Be sure to try playing back the disc to confirm that the parental level setting is working correctly. If it is not working correctly, try changing the country code.

• You can use the parental lock function only with DVD discs that are equipped with the parental lock feature.

• On some DVD discs, the PARENTAL level setting is fixed and cannot be modified.

• The parental level depends on countries. If you do not set the country code correctly, it fails to work correctly.

• Some DVD discs allow the viewer to temporarily change the parental level setting to view the original scenes. When this prompt appears, input the password to view the original scenes.

Country Code List

USA CANADA JAPAN GERMANY FRANCE UK ITALY SPAIN SWISS SWEDEN HOLLAND NORWAY DENMARK

FINLAND BELGIUM HONG KONG SINGAPORE THAILAND MALAYSIA INDONESIA TAIWAN PHILIPPINE AUSTRALIA RUSSIA CHINA

DVD Setup

AUDIO Setting

COMPRESSION ............ Use this setting for increasing the average

volume of Dolby Digital audio when playing a DVD.

DIGITAL..................Use this setting for specifying the type of

digital output when playing a disc.

CINEMA VOICE.............Use the setting for raising the sound of the

center speaker to make the voices in a movie easier to hear.

Setting the COMPRESSION (Dolby Digital output level)

When Dolby Digital is used to record the audio on a DVD disc, the average overall volume level of the audio is relatively lower than that produced by a VIDEO CD/Audio CD. This is to provide the widest possible dynamic range. To counteract this, this product automatically raises the overall average volume level of a disc recorded using Dolby Digital to a level that is similar to that of a VIDEO CD/Audio CD.

COMPRESSION:

OFF

DVD

Dolby Digital audio • Low audio level

COMPRESSION:

•

Audio level the same as audio CD, etc.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VIDEO CDs

Audio CDs

• OFF.............. Audio level recorded on disc is played back without

modification.

• ON ............... Dolby Digital average audio level is increased so it

sounds similar to that of a VIDEO CD/Audio CD.

Preparation

• See Preparing to Watching a VCR or a DVD on page 18.

1 Press DVD SETUP to display the SETUP screen. 2 Use ' or " to select the “ AUDIO” and then press ENTER.

AUDIO COMPRESSION OFF

DIGITAL MPEG CINEMA VOICE OFF

ENTER

SELECT ENTER

BITSTREAM BITSTREAM

RETURN

VCR/DVD COMBINATION

3 Use ' or " to select “COMPRESSION”. 4 Press ENTER to display the settings you can select.

DVD Setup

AUDIO COMPRESSION

OFF

SELECT

ENTER

RETURN

5 Use ' or " to select “ON” or “OFF”.

• Use of the “OFF” setting is recommended when the product is connected to audio equipment.

6 Press ENTER to confirm the setting.

•

When you have completed the above setting, press RETURN to return to the SETUP screen. However, if you want to specify the

DIGITAL” setting in succession, proceed to step 1 below.

“

• Whenever the “COMPRESSION” setting is “ON”, the 3D VIRTUAL SURROUND setting is automatically changed to “OFF”.

Setting the DOLBY DIGITAL

When playing a disc recorded using Dolby Digital (5.1ch), you can specify either “BITSTREAM” or “D-PCM” as the digital type output.

• Before setting the “ page 46.

DIGITAL” , perform the step 1 and 2 on

1 Use ' or " to select “ DIGITAL”. 2 Press ENTER to display the settings you can select.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

AUDIO

DIGITAL

BITSTREAM

D-PCM

SELECT

ENTER

RETURN

3 Use ' or " to select “BITSTREAM” or “D-PCM”.

BITSTREAM: Use this setting for a digital connection of a

receiver (amplifier) equipped with a Dolby Digital decoder.

D-PCM: Use this setting for a digital connection to the

(Down Mix PCM) PCM digital input jack of a DAT or MD, or for

a digital connection to a receiver (amplifier) that does not have a Dolby Digital decoder.

4 Press ENTER to confirm the setting. 5 When you have completed the setting above, press RETURN to

return to the SETUP screen. However, if you want to go on and specify the other settings, use ' or " to display other setting screen.

VCR/DVD COMBINATION

DVD Setup

Setting the MPEG

•

Before setting the “MPEG”, perform the step 1 to 2 on pages 47 and 48.

1 Press ENTER and then use ' or " to select “MPEG”. 2 Press ENTER to display the settings you can select.

BITSTREAM

SELECT

ENTER

RETURN

3 Use ' or " to select “BITSTREAM” or “PCM”.

BITSTREAM: Use this setting for a digital connection of a

receiver (amplifier) equipped with an MPEG Audio decoder.

PCM: Use this setting for a digital connection to the

PCM digital input jack of a DA T or MD, or for a digital connection to a receiver (amplifier) that does not have an MPEG Audio decoder.

4 Press ENTER to confirm the setting. 5

Press RETURN to exit the SETUP screen and return to normal screen.

• If you want to go on and specify other settings, use ' or " to display the other SETUP screen without pressing RETURN.

When playing a disc recorded using DTS, the bitstream type signal is output regardless of the setting of “

DIGITAL” and “MPEG”.

Setting the CINEMA VOICE

This function is raising the sound of the center speaker to make the voices in a movie easier to hear.

•

Before setting the “CINEMA VOICE” , perform the step 1 and 2 on page 46.

1 Use ' or " to select “CINEMA VOICE”. 2 Press ENTER to display the settings you can select.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

AUDIO CINEMA VOICE

OFF

SELECT

ENTER

RETURN

3 Use ' or " to select “ON” or “OFF”.

ON: OFF: Set to “OFF” when you do not want to use this function.

Set to “ON” when you want to raise the sound of the voice.

4 Press ENTER to confirm the setting. 5

When you have completed the setting above, press RETURN to return to the SETUP screen. However, if you want to go on and specify the other settings, use ' or " to display other setting screen.

• The CINEMA VOICE setting raises the sound of the center channel threfore it does not affect the voices in other channels.

• Even if this function is set to “ON”, the result may or may not be effective depending on the disc.

VCR/DVD COMBINATION

DISC LANGUAGE Setting

Use this setting for selecting the language for subtitles, audio tracks and disc menu.

DVD Setup

Setting SUBTITLE, AUDIO and MENU languages

Preparation

• See Preparing to Watch a VCR or a DVD on page 18.

1 Press DVD SETUP to display the SETUP screen. 2 Use ' or " to select the “ DISC LANGUAGE”.

TV MODE PARENTAL LEVEL 8 AUDIO DISC LANGUAGE

ENTER

SELECT ENTER

4:3

RETURN

3 Press ENTER and then use ' or " to select “AUDIO”,

“SUB TITLE” or “MENU”.

•

You can set “AUDIO”, “SUB TITLE” or “MENU” individually.

(Example) Selecting “AUDIO”

DISC LANGUAGE AUDIO

SUB TITLE MENU

ENTER

SELECT ENTER

ENGLISH

ENGLISH ENGLISH

RETURN

4 After selecting the item, press ENTER.

• After selecting “MENU”, make sure to set the language by following steps 2 to 5 under “Selecting languages from OTHER” on the next page.

5 Select the language you want to use with ', ", \ and |.

(Example) Selecting “FRENCH”

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

AUDIO

ENGLISH SPANISH

FRENCH

ITALIAN GERMAN

ENTER

CHINESE SWEDISH DUTCH RUSSIAN OTHER

SELECT

RETURN

• If you want to use any languages which are not on the OSD, proceed to step 1 under “Selecting languages from OTHER” on the next page.

6 Press ENTER to confirm the setting. 7 Repeat steps 4 to 7 above to go on with other “DISC

LANGUAGE” settings in succession.

If you want to complete the setting here, press RETURN to

•

return to the SETUP screen. However, if you want to display other setting screens, press ' or " without pressing RETURN.

DVD Setup

Selecting languages from OTHER

Select “OTHER” with ', ", \ and |, then press ENTER to set the “OTHER” input item (two letters).

• See Language Code List for Disc Language on page 50 when selecting the code.

(Example) Selecting “OTHER” in “AUDIO”

DV- NC70W DV- NC70

DV- NC70X

G-CODE

PROG

OTHER AUDIO 1 E

AUDIO 2 N

SELECT

ENTER

RETURN

• The “SUB TITLE” and “MENU” screens are displayed respectively when being set.

2 Press \ or | to select the alphabet as the first letter on

“AUDIO 1”. (Upper side)

3 Press " to move the cursor to “AUDIO 2”. (Lower side)

OTHER

AUDIO 1 F

AUDIO 2 A

SELECT

ENTER

RETURN

4 Press \ or | to select the alphabet as the second letter. 5 Press ENTER to confirm the setting.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

• Press RETURN to return to the previous screen.

VCR/DVD COMBINATION

DVD Display Information

Operation Mode Indicators

Each time ON SCREEN on the Remote is pressed, the display on the TV screen changes the mode in the following sequence:

AUTO mode → ON mode → OFF mode

• AUTO mode ....Displays indicators for 3 seconds when operation begins.

• ON mode .........Displays indicators continually until the operation mode is changed.

• OFF mode .......Does not display indicators.

Each time DISPLAY on the Remote is pressed, the DVD Front Panel Display changes the mode in the following sequence:

Time mode → Operation Status mode → Title mode

• Time mode ..................... Displays the playing time*.

•

Operation Status mode

• Title mode ...................... Displays the total number of titles, chapters, or tracks.

* When the disc you attempt to play has no information on time, the operation status is displayed.

This product displays the information shown below on the TV screen and on the DVD Front Panel Display depending on the operation status.

Display Examples

If no disc is loaded or an unplayable disc is loaded when this product is switched on

.... Displays the operation you perform such as “PLAY”, “REV”.

TV Screen DVD Front Panel Display Remarks

“– – – – –” appears when the tray is closed and:

1) There is no disc in the tray.

2) The disc type is not DVD, VIDEO CD or Audio CD.

3) The disc is not loaded correctly (upside-down, etc.)

Tray open Tray closed Loading

Stopped Playing Still/Paused

Fast forward Fast reverse Slow Playback Control

The indicator changes to show other indicators (total time, etc.)

When a DVD or VIDEO CD is played back.

When an Audio CD is played back.

Does not work with Audio CDs.

Region (Local) Number Error Indicator

If the region (local) number of the disc that you attempt to play differs from the region number of this product, “ REGION CODE ERROR” appears on the TV screen and the disc tray slides out. (The disc cannot be played.)

Language Code List for Disc Language

Code Language Name

AA Afar AB Abkhazian AF Afrikaans AM Ameharic AR Arabic AS Assamese AY Aymara AZ Azerbaijani BA Bashkir BE Byelorussian BG Bulgarian BH Bihari BI Bislama BN Bengali;

Bangla BO Tibetan BR Breton CA Catalan CO Corsican CS Czech CY Welsh DA Danish DE German DZ Bhutani EL Greek EN English EO Esperanto ES Spanish ET Estonian EU Basque FA Persian FI Finnish FJ Fiji FO Faroese FR French

Code Language Name

FY Frisian GA Irish GD Scots Gaelic GL Galician GN Guarani GU Gujarati HA Hausa HI Hindi HR Croatian HU Hungarian HY Armenian IA Interlingua IE Interlingue IK Inupiak IN Indonesian IS Icelandic IT Italian IW Hebrew JA Japanese JI Yiddish JW Javanese KA Georgian KK Kazakh KL Greenlandic KM Cambodian KN Kannada KO Korean KS Kashmiri KU Kurdish KY Kirghiz LA Latin LN Lingala LO Laothian LT Lithuanian L V Latvian, Lettish

Code Language Name

MG Malagasy MI Maori MK Macedonian ML Malayalam MN Mongolian MO Moldavian MR Marathi MS Malay MT Maltese MY Burmese NA Nauru NE Nepali NL Dutch NO Norwegian OC Occitan OM (Afan) Oromo OR Oriya PA Panjabi PL Polish PS Pashto, Pushto PT Portuguese QU Quechua RM Rhaeto-

Romance RN Kirundi RO Romanian RU Russian RW Kinyarwanda SA Sanskrit SD Sindhi SG Sangho SH Serbo-

Croatian SI Singhalese SK Slovak

Code Language Name

SL Slovenian SM Samoan SN Shona SO Somali SQ Albanian SR Serbian SS Siswat ST Sesotho SU Sundanese SV Swedish SW Swahili TA Tamil TE Telugu TG Tajik TH Thai TI Tigrinya TK Turkmen TL Tagalog TN Setswana TO Tonga TR Turkish TS Tsonga TT Tatar TW Twi UK Ukrainian UR Urdu UZ Uzbek VI Vietnamese VO Volapük WO Wolof XH Xhosa YO Yoruba ZH Chinese ZU Zulu

Watching the VCR

Playback .......................................................................................... 52

Inserting a Video Cassette............................................................. 52

Playback......................................................................................... 52

Video Search (with the Remote) .................................................... 52

Fast Forwarding and Rewinding..................................................... 53

Slow Motion Playback (with the Remote)....................................... 53

Still Picture and Frame Advance.................................................... 53

Double Speed Playback................................................................. 53

NTSC Tape Play Back on PAL TV.................................................. 54

Full Auto Playback ......................................................................... 54

Auto Head Cleaning System.......................................................... 54

Auto Tracking Control System........................................................ 54

Quick Start with Full Loading Mechanism...................................... 54

AUTO RENT AL............................................................................... 55

COLOUR........................................................................................ 55

BLUE BACK................................................................................... 56

Playback of Hi-Fi Recorded Tapes ................................................. 57

Audio Output Mode ........................................................................ 57

Adjusting Hi-Fi Audio T racking ....................................................... 57

Sharp Super Picture ....................................................................... 58

Auto Repeat ..................................................................................... 59

Auto Zero Back................................................................................ 60

DPSS (Digital Program Search System)/Skip Search .................. 61

DPSS ............................................................................................. 61

Skip Search.................................................................................... 61

TV Programme Recording.............................................................. 62

Cassette Erase Protection ............................................................. 62

Recording a TV Programme .......................................................... 62

To Watch Another TV Programme While Recording ...................... 62

Recording NICAM/IGR Multiplex Broadcasts ................................ 63

Simple Recording Timer ................................................................. 64

Immediate Recording..................................................................... 64

Programming the Timer with G-

Setting the Programme Number In Step 4..................................... 67

Recording with the Timer ............................................................... 68

Confirming Timer Programmes...................................................... 71

Cancelling Timer Programmes....................................................... 72

T ape Dubbing .................................................................................. 73

Recording a DVD Disc onto a Video Cassette.............................. 74

Recording a DVD disc onto a Video cassette

(Tape Editing mode)................................................................... 74

CODE

System (DV-NC70W only)... 65

WATCHING

THE VCR

Playback

Inserting a Video Cassette

Gently insert the video cassette into the cassette compartment. The Product turns on automatically. If the cassette is inserted incorrectly, the loading system will not function. Do not force the cassette into the Product. When the cassette has been properly loaded, “ pears on the VCR Front Panel display. To remove the cassette, press EJECT during stop mode.

” ap-

PLAY STOP

PLAY/×2

OPERATE

REW

EJECT/STOP

REC

(

AV 2 IN

MONO

VIDEO

)

AUDIO-R

VCR/DVD SELECTOR

TIMER

VCR

OPEN/CLOSE

DVD

PLAY/ 2

Playback

1 Switch on your TV and select the video channel. 2 Press OPERATE to turn on the Product.

3 Insert a cassette. 4 Press ûPLAY. (The auto tracking control system engages and

“

|” flashes on the TV screen for a few seconds.)

5 Press ËSTOP to stop playback. (If the tape reaches its end, the

Product will automatically rewind the tape to the beginning, eject the cassette, and turn off the power. If a DVD is being played back, the power will not turn off.)

• NTSC tapes recorded in Hi-Fi and EP mode may appear distorted during playback. This does not indicate a malfunction. The tracking function can be used to slightly enhance the picture quality.

Video Search (with the Remote)

Use the following procedure to quickly find the section you want, while viewing the picture.

1 During playback, press FF

REW for reverse search.

There are 2 search speeds in each direction. The Product switches between them each time the button is pressed.

for forward video search, or

2 Press ûPLAY to resume normal playback.

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

STOP

VCR/DVD

SELECTOR

ANGLE

INPUT SELECT

EJECT /

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

• During video search of a tape recorded in the LP mode and EP mode, the upper part of the picture may be skewed to one side.

TAPE SPEED

VSF/VSR 1 VSF/VSR 2

SP ✕ 5 ✕ 9

✕ 5 ✕ 11 ✕ 9 ✕ 27

SP/LP

✕ 5 ✕ 7 ✕ 9 ✕ 21

PAL TAPE

MESECAM TAPE

PAL TAPE EP

NTSC TAPE

●

VSF : Video Search Forward

●

VSR : Video Search Reverse

VCR/DVD COMBINATION

Fast Forwarding and Rewinding

1 Press ËSTOP to stop the video tape. 2 Press FF

or È REW.

3 Press ËSTOP to stop fast forward/rewind.

• If you use other than E-90/E-180 cassettes, fast forward and rewind may take somewhat longer.

Slow Motion Playback (with the Remote)

1 Press SLOW on the Remote during playback. 2 Press SLOW

motion playback speed between 1/5 and 1/30 of the normal playback speed.

(to the left of SLOW) to vary the slow

3 Press ûPLAY to resume normal playback.

• No noise can be erased when a tape recorded in the NTSC SP mode is played back in special modes (still, slow motion, etc.). However, this does not indicate a malfunction with the Product.

• During slow motion, still picture, frame advance and double speed playback with a tape recorded in the PAL EP mode, noise may appear.

OPERATE

EJECT/STOP

(

AV 2 IN

MONO

VIDEO

PLAY/×2

REW

)

- AUDIO-R

EJECT /

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REC

PLAY/ 2

REW

STOP

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD SELECTOR

VCR/DVD

SELECTOR

ANGLE

CH /

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

Playback

PLAY STOP

TIMER

DVD

VCR

G-CODE

PROG

OPEN/CLOSE

Still Picture and Frame Advance

INPUT SELECT

VCR DVDAM/PM

1 Press âPAUSE/STILL during playback. This will freeze the

picture on your TV.

2 If noise bars appear on the screen during still picture, set your

Product to the slow mode and press CH ' / " to make the noise disappear. Then press âPAUSE/STILL again.

3 If there is vertical jitter during still picture playback, press

CH ' / " to stop jitter.

4 Press âPAUSE/STILL during still mode for frame advance.

REV FWD

PLAY

REC

TAPE

SPEED

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

5 Press ûPLAY again to resume normal playback.

Double Speed Playback

1 Press ûPLAY during playback. The tape will be played back at

twice the normal speed.

VCR/DVD COMBINATION

2 Press ûPLAY to resume normal playback.

• Sound is muted during video search, slow motion, still picture, frame advance and double speed playback.

• To avoid damage to the tape, your Product will resume normal playback after about 5 minutes of slow motion playback

and still picture.

• If an NTSC tape and a PAL or MESECAM tape recorded in LP mode is played back in still picture, frame advance, slow motion, Double speed, or Video Search mode, the picture may have horizontal jitter and the top of the picture will be distorted, but this does not indicate VCR malfunction.

Playback

NTSC Tape Play Back on PAL TV

When you play back an NTSC tape on your Product, it is possible to use a PAL or multi-system compatible TV. However, please note the following:

• The picture will shrink vertically to some degree, as shown in the diagram, but this does not indicate a malfunction in your TV or Product.

• If your TV does not have a V-HOLD control, the picture may roll and be unwatchable. However, if you use a TV with a V-HOLD control, you can stop the rolling by adjusting the V-HOLD control and watch the picture.

• Horizontal noise bars may appear on the screen during special effect playback (video search, still, slow, frame advance, and double speed playback), possibly accompanied by discolouring.

• Although NTSC tapes can be played back into a PAL TV, those tapes cannot be dubbed by a PAL system VCR connected to the AUDIO OUT and VIDEO OUT terminals of this product. Tapes recorded in this way cannot be played back on PAL system VCRs.

• Set the Colour mode to AUTO or NTSC, and set the NTSC mode to PAL TV.

Full Auto Playback

(This function only works when AUTO RENTAL mode on the MODE selection screen is set to “OFF”.) Full Auto Playback lets you enjoy playback with ease. When you insert a cassette with the erasure protection tab removed, your Product automatically turns on the power and plays back the tape. When the tape reaches its end, the Product automatically rewinds the tape, ejects it and turns off the power. If a DVD is being played back, the power will not turn off.

• If the erasure protection hole is covered, press ûPLAY after the power turns on automatically.

Auto Head Cleaning System

When the tape is inserted or ejected, this system automatically cleans the drum and heads with a special roller before recording or playback begins, protecting the heads and drum from dirt and preserving beautiful picture quality.

Auto Tracking Control System

This function automatically adjusts the tracking to match the recorded tape. Auto tracking engages in the following cases:

• When you insert the cassette and begin playback.

• When you press CH ' / " at the same time.

• When the Product has been playing back an unrecorded section of tape,

and then reaches a recorded tape segment.

When auto tracking engages, “

• When a poorly recorded tape is played back, auto tracking may not operate normally. In this event, manually adjust

the tracking with CH ' / " to make any noise disappear.

|” on the TV screen flashes for a few seconds.

Poor Tracking Normal tracking

Quick Start with Full Loading Mechanism

Your Product has a standby function (Full Loading Mechanism) to allow immediate recording and playback. After pressing standby mode.

ÆÆ

ÆREC or ûPLAY, it takes about 2 seconds until recording or playback is engaged when in the

ÆÆ

AUTO RENTAL

(This function only works when AUTO RENTAL mode on the MODE selection screen is set to “ON”.) The convenient auto rental mode lets you enjoy playback with ease. When you insert a cassette with the erasure protection tab removed (rental videos, etc.), your Product automatically turns on the power, rewind the tape forward to find the recorded section, and plays back the tape. When the tape reaches the end of recorded section, the Product automatically rewinds the tape, ejects it and turns off the power. If a DVD is being played back, the power will not turn off.

1 Press VCR MENU to display the menu screen. 2 Press ' / " to select “MODE”. 3 Press SET to confirm. 4 Press ' / " to select “AUTO RENTAL”.

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

5 Press

\ /

| to select “ON” or “OFF”.

6 Press SET to confirm and then press VCR MENU to return to

the normal screen.

• If there is more than a 15 second unrecorded section between

recorded sections, the tape will automatically stop and rewind. To watch the next recorded section, press ËSTOP, fast forwar d to that section and play the tape.

• If the erasure protection hole is covered, press ûPLAY after the

power turns on automatically. (AUTO RENTAL Mode does not work.)

• The AUTO REPEAT mode has priority over the AUTO RENTAL mode. If

the AUTO REPEAT mode is set to “ON” and the video cassette reaches its end, the Product will rewind the tape and play it back again without ejecting the tape or turning off the power.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

Playback

G-CODE

PROG

COLOUR

If the quality of a colour recording is poor, the picture may turn black and white. In this event, set the COLOUR mode on the MODE selection screen to PAL (fixed PAL colour mode), MESECAM (fixed MESECAM colour mode), NTSC (fixed NTSC mode). Normally, the colour mode should be set to “AUTO” mode. (See “Mode Selection” on page 25.)

1 Follow steps 1 to 3 from “AUTO RENTAL” above.

Playback

2 Press ' / " to select “COLOUR”.

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

3 Press

\ /

| to select “AUTO”, “PAL”, “MESECAM” or “NTSC”.

4 Press SET to confirm and then press VCR MENU to return to

the normal screen.

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

• When the colour mode is set to fixed colour mode while the Product is

playing back a black and white tape or is receiving a black and white broadcast, the picture may be coloured. In this event, set the COLOUR mode on the MODE selection screen to “AUTO” mode.

BLUE BACK

This function eliminates monitor noise and mutes sound during playback of unrecorded portions of a tape, and when receiving a non-broadcasting channel. A blue screen will also appear if the Product is set to the Auxiliary input (LINE IN) mode but no video signal is fed to the Product. (The BLUE BACK mode is set to “AUTO” at the factory.)

1 Follow steps 1 to 3 from “AUTO RENTAL” on page 55. 2 Press ' / " to select “BLUE BACK”.

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

3 Press

\ /

| to select “AUTO” or “OFF”.

4 Press SET to confirm and then press VCR MENU to return to

the normal screen.

• Blue Back does not function during still picture, variable slow motion

and video search.

• Blue Back may not function properly if the broadcast signal is too

strong or too weak.

• Blue Back cannot be recorded.

•

If the antenna signal is weak while recording a TV programme, or if the input signal is weak while tape dubbing, the monitor screen may turn blue since the Product may not recognize whether or not a proper signal is being received. In this event, set the BLUE BACK mode to “OFF”.

Playback of Hi-Fi Recorded Tapes

This Product will play back both video and audio, or audio-only tapes recorded in the Hi-Fi mode.

Playback

• Stereo sound output is only possible using the AUDIO OUT terminals.

Sound from the radio frequency converter (RF OUT) is mono only. A blue screen will appear if audio-only Hi-Fi tapes are played back.

Audio Output Mode

The audio output mode is controlled by AUDIO OUTPUT on the Remote. The Product is normally set to the Hi-Fi mode, with

and displayed on the VCR Front Panel display, and normal stereo sound output. Select , and only the Hi-Fi Left channel audio is heard from both the Right and Left speakers. Select , and only the Hi-Fi Right channel audio is heard from both the Right and Left speakers. If you select the mono linear track,

• Should the Hi-Fi output level be poor, the Product will automatically select the mono linear track output.

• When playing back tapes which have only Hi-Fi sound recorded: If Hi-Fi sound is not reproduced, or if there is some noise in the audio, press CH ' / " until the sound improves.

and will disappear.

Adjusting Hi-Fi Audio Tracking

(To adjust the Hi-Fi tracking manually when playing back a poorly recorded Hi-Fi tape.)

• Normally you can simultaneously press and hold both CH ' / " to obtain the optimal Hi-Fi audio tracking.

• If Hi-Fi audio is unstable (frequent dropouts, etc.) with a rental video, a tape recorded on another VCR, restore normal tracking while playing back the tape as described below:

1 Press ON SCREEN on the Remote and select the Full Display

mode. (See page 36.)

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

2 Simultaneously press CH ' / ". 3 Press CH ' / " repeatedly at equal, short intervals until the

and indicators disappear from the On Screen Display (OSD).

4 Press CH ' / " in the same manner while counting button

operations until the L and R indicators reappear and then disappear again.

5 Press CH ' / " again for half the number of times counted in

step 4 above to obtain optimal track.

Sharp Super Picture

This function creates clearer picture quality only during playback.

1 Press VCR MENU to display the menu screen. 2 Select “MODE” with ' / " and then press SET to confirm.

MENU G-CODE TIMER

MODE

CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

3 Select “S.PICTURE” with ' / ". Then set it to “ON” or “OFF”

\ /

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

with

ON:

Normally leave the mode set to ON. This high picture quality function will create a clearer image during playback.

OFF:

Set to OFF when playing back a tape on the Product while editing or when strong noise appears on the screen.

4 Press SET to confirm and return to the menu screen. 5 Press VCR MENU to exit to normal screen.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

• This function only operates during playback. It will not operate when

recording or watching a TV program with the VCR tuner.

• When playing S-VHS tape:

1. Sharp Super Picture is set to off automatically. When finished playback, the setting will return to the previous setting.

2. You cannot change ON/OFF setting manually.

• The ON/OFF status of the Sharp Super Picture can be checked when ON SCREEN is pressed to display OSD.

• When the Product power is turned off, the Sharp Super Picture setting is retained in memory.

• If power is interrupted for more than 60 minutes (power failure, etc.), the setting will return to ON.

VCR/DVD COMBINATION

Auto Repeat

With this feature, the entire tape is played back repeatedly.

1 Press VCR MENU to display the menu screen. 2 Select “MODE” with ' / " and then press SET to confirm.

MENU G-CODE TIMER

MODE

CHANNEL PRESET CLOCK LANGUAGE

:SELECT SET:ENTER MENU:EXIT

3 Select “REPEAT” with ' / ". Then set the mode to “ON” or

“OFF” with

\ /

COLOUR AUTO PAL MESECAM NTSC NTSC 3.58 4.43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S.PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT

4 Press SET to confirm and return to the menu screen. 5 Press VCR MENU to return to normal screen.

• “REPEAT” will be displayed on the OSD when the Auto Repeat mode is “ON”.

• If the Auto Repeat is “ON” and the tape is rewinded to the beginning with rewind or reverse video search, the tape will automatically start playback.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

Auto Zero Back

The zero-back function makes the cassette fast forward (or rewind) to the previously set “0:00.00” point and stop there.

1 Make sure the counter is displayed, then press CLEAR on the

Remote at the point you wish to return and later “0:00.00” is displayed.

2 Press ZERO BACK on the Remote. The Product automatically

detects the direction of the “0:00.00” position and fast forwards (or rewinds) the tape.

3 When the tape reaches the “0:00.00” position, the tape

automatically stops.

• The zero-back function does not operate during recording and fast forward (or rewind). The function works during the playback, stop and video search modes.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

DPSS (Digital Program Search System)/Skip Search

DPSS

With this feature you can quickly locate a desired section of the tape. The DPSS feature makes use of index signals to search for a specified tape segment and begin playback automatically.

Index signal

An index signal is automatically recorded on the tape at the start of ordinary recording, simple recording timer and timer recording.

Rewind

Current tape position

1-1 2

1 Load a tape containing index signals into the Product. 2 Select the index number of the desired programme using DPSS

on the Remote. Search starts immediately . (When a signal is located, the displayed number decreases.)

3 When the selected index signal-encoded section is found,

playback begins automatically.

• DPSS may not function properly if the index signals are too close together (within 8 minutes of each other).

• DPSS can be cancelled with ûPLAY or ËSTOP.

• If the tape reaches its end or is rewinded completely before locating

the desired index signal, DPSS is cancelled.

• DPSS may not function for damaged or worn tapes.

•

The DPSS function cannot be used with tapes that contain no index signals.

• The starting point of a programme may vary slightly.

• DPSS does not operate during the slow, record, fast forward, rewind,

timer standby, and timer recording modes, or when there is no cassette loaded.

Fast forward

Index signals

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

Skip Search

When SKIP SEARCH on the Remote is pressed during playback mode, the product will perform a forward video search for a fixed interval of playback time before resuming playback. Depending on how many times the button is pressed, it is possible to set the forward video search time to approx. 30, 60, 90 or 120 seconds of recorded material.

Number of Times Pressed

1 time

2 times

3 times

4 times

Forward Video Search Time

Approx. 30 sec. (of playback time)

Approx. 60 sec. (of playback time)

Approx. 90 sec. (of playback time)

Approx. 120 sec. (of playback time)

VCR/DVD COMBINATION

TV Programme Recording

Cassette Erase Protection

PAL SECAM

erasure of recorded material. Removing the tab prevents recording. To record on a video cassette with the tab removed, place adhesive tape over the tab opening.

cassette has a removable tab to prevent accidental

Recording a TV Programme

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR.

• Ensure the Video channel is selected on the TV.

1 Insert the cassette, making sure the erasure protection hole is

covered.

2 Select the channel position you wish to record with CH ' / ". 3 Select the SP (Standard Play), EP (Extended Play) or LP (Long

Play) recording speed with TAPE SPEED on the Remote (“SP”, “EP” or “LP” will light up on the VCR Front Panel display.) SP (Standard Play) gives the best picture quality, EP (Extended Play) gives the triple recording time and LP (Long Play) gives the double recording time.

ERASURE PROTECTION TAB

DV- NC70W DV- NC70

DV- NC70X

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

VCR MENU

DVD SETUP

DVD MENU

ZERO BACK

SKIP SEARCH

EJECT

OPEN/

SET

ENTER

G-CODE

PROG

• If the COLOUR mode is set to “AUTO” or “MESECAM”, when a

SECAM signal is received and the EP mode is selected, the Product will automatically change the EP mode to LP mode.

4 Press

ÆÆ

ÆREC. (If the erasure protection hole is uncovered, the

ÆÆ

cassette will be ejected.) To pause during recording, press âPAUSE/STILL. T o resume recording, press âPAUSE/STILL again.

5 To stop recording, press ËSTOP.

• The pause mode disengages automatically after about 5 minutes, and

the Product enters stop mode.

• To record audio and video from an external source through the

AUDIO/VIDEO terminal on the rear of the Product, pr ess INPUT SELECT on the Remote to select the AV channel position situated between the last channel and first channel. (When the AV position is selected, “L1” or “L2” is displayed where a channel position number is usually displayed.)

• If the TV signals are weak and the picture changes to monochrome,

set the strict colour mode on the MODE selection screen. (See ”Mode Selection” on page 23.) Normally, the colour mode should be set to “AUTO”.

To Watch Another TV Programme While Recording

After steps 1 to 4 have been completed, select the programme you wish to view using the TV tuner. At the end of the tape, your Product will automatically stop recording, rewind the tape, eject it and then turn off the power. If a DVD is being played back, the power will not turn off.

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

TV Programme Recording

Recording NICAM/IGR Multiplex Broadcasts

This Product is capable of receiving NICAM multiplex broadcasts (PAL-I, B/G, D/K) and IGR multiplex broadcasts (PAL-

OSD’s MODE is set to AUTO. For information on how to carry out NICAM setting (See “Mode Selection” on page 25). IGR multiplex broadcasts will be recorded on stereo/bilingual. (The AUTO/OFF setting will not function.) This Product automatically records on two types of audio track.

Hi-Fi track:

Special rotary heads will be used to record an audio signal deep in the video track in Hi-Fi. Multiplex broadcasts fall into “stereo” and “bilingual” broadcasts and they will be automatically recorded on their respective tracks.

Normal track:

Conventional analogue audio is always recorded on the normal track (mono sound) regardless of whether your Product is receiving a multiplex broadcasts or not.

B/G, D/K). NICAM multiplex broadcasts will be recorded in ster eo/bilingual when the NICAM setting on the

Setting of “NICAM” in MODE

Broadcast

Normal sound (mono sound)

NICAM (bilingual)

NICAM (stereo)

IGR (bilingual)

IGR (stereo)

Hi-Fi track Normal track Hi-Fi track Normal track

mono

sound

NICAM sound

(bilingual)

NICAM sound

(stereo)

IGR sound

(bilingual)

IGR sound

(stereo)

On screen display

• When receiving a stereo multiplex broadcast,

(LR) will be indicated on the on screen display.

• When receiving a bilingual multiplex broadcast, will be displayed on the on screen display.

OFF positionAUTO position

mono

sound

mono

sound

mono

sound

mono

sound

mono

sound

Broadcast

TYPE

Stereo

Bilingual

mono

sound

mono

sound

mono

sound

IGR sound

(bilingual)

IGR sound

(stereo)

NICAM

mono

sound

mono

sound

mono

sound

mono

sound

mono

sound

IGR

• There are tapes, though small in number, which have a normal track that has been divided into two tracks. On such

tapes, stereo as well as bilingual audio are recorded on the normal track. If such a tape is played back on your Product, the tape’s stereo sound will be reproduced in monaural and its bilingual in both languages combined.

• When a cassette tape on which a NICAM multiplex broadcast has been recorded in stereo or bilingual mode is played

back by a VCR that is not a Hi-Fi VCR, only the sound on the normal track will be reproduced.

• When you select “OFF” for NICAM in the OSD MODE, the stereo and bilingual audio of a NICAM multiplex broadcast

will be fixed to the normal sound.

Simple Recording Timer

Immediate Recording

This is convenient function when having an unexpected visitor or telephone call.

1 Select the channel position to be recorded with CH ' / ".

(Example) Channel position 2

2 S.PICTURE ON I/

SP L R

REPEAT

8:00 15/12 00 0:00.00

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

2 Press

ÆÆ

ÆREC to enter the normal recording mode. Then, press

ÆÆ

ÆREC repeatedly to set the desired ending time.

ÆÆ

(Example) Ending time 9:30

2 S.PICTURE ON I/ SP STOP 9:30 L R

8:00 15/12 00 0:00.00

• Each press of

• Press ËSTOP to terminate recording.

ÆÆ

ÆREC increases the stop time by 10 minutes.

ÆÆ

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

Programming the Timer with G-

CODE

This product has the G-CODE programming system. By simply inputting

CODE number with the number buttons, you can programme your

the GProduct timer recording. The G-CODE numbers are listed in most newspaper, TV guide, and local cable TV listings. The timer can be set for automatic recording of up to 8 events over a 365 day period. In addition, each of the events can be set to be recorded on a daily or weekly basis up to the limit of the tape.

System (DV-NC70W only)

DV- NC70W DV- NC70

DV- NC70X

G-CODE

PROG

Preparation

• Load the cassette, ensuring the erasure protection hole is covered. The Product power will automatically turn on.

• Check that the clock is displaying the correct time.

1 Press VCR MENU. Then select “G-CODE” with ' / " and press

SET to confirm.

G-CODE

TIMER MODE CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

2 Set the G-CODE number with the number buttons (0 to 9).

G-CODE NO. -

ONCE WEEKLY DAILY

:SELECT SET:ENTER MENU:EXIT

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

• For the G-CODE number, refer to your newspaper or TV guide.

• Press the G-CODE button on the Remote to directly select this screen.

3 If you want to record only once, press SET and go to step 4.

Otherwise, press ' / " to select daily/weekly setting mode and

select “DAILY” or “WEEKLY” with

G-CODE NO. 1234

ONCE WEEKLY DAILY

:SELECT :CHANGE SET:ENTER MENU:EXIT

• “ONCE”: To record only once.

• “WEEKLY”: To record every week at the same time.

• “DAILY”: To record every day at the same time.

\ /

|. Then press SET to confirm.

VCR/DVD COMBINATION

Programming the Timer with G-CODE® System

4 If you are going to record a programme from a station which

does not have the PR number programmed, (“

” is displayed)

set that number to be the same as the PR number to which your broadcasting channel is set into. (See Note on page 67.) Use the number buttons (0 to 9) or ' / ". Then press

| .

(Ex.: 47)

1/2 DATE PR START STOP 15/12 47 12:00 12:30 SP

--/-- -- -:-- -:-- --

PR :PRESET CH :SELECT :CHANGE SET:ENTER MENU:EXIT

PMPM

5 Select the tape speed with ' / ".

1/2 DATE PR START STOP 15/12 47 12:00 12:30 SP

--/-- -- -:-- -:-- --

SP/LP.EP:TAPE SPEED :SELECT :CHANGE SET:ENTER MENU:EXIT

• If the COLOUR mode is set to “AUTO” or “MESECAM”, when a

SECAM signal is received and the EP mode is selected, the Product will automatically change the EP mode to LP mode.

• A tape recorded in the PAL EP (Extended Play) mode can only be

playback in a VCR which have its same function (PAL EP (Extended Play) mode).

• For best result, it is advisable to Playback or Recording EP mode with

this Product.

PMPM

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

6 Press SET.

G-CODE NO. -

ONCE WEEKLY DAILY

:SELECT SET:ENTER MENU:EXIT

• To programme additional timer settings, press SET and repeat steps 2

and 6.

VCR/DVD COMBINATION

Programming the Timer with G-CODE® System

VCR

7 Press VCR MENU to return to the normal screen.

8 To set the product for automatic timer recording, press TIMER

ON/OFF and ensure the “

display.

—

VCR

L R

SEPVP D

• Please be sure to check that the start and end times of two different

programmes do not overlap, as the remote control has been designed to accept the basic individual G-CODE number only. If the recording periods of two programmes overlap, the beginning of the second programme will not be recorded.

• To cancel the programmed G-CODE setting, select the TIMER setting

mode on the menu screen. Then select the programme number you wish to cancel with ' / " and press CLEAR. (See “Cancelling Timer Programmes” on page 72.)

Setting the Programme Number In Step 4

When using the G-CODE system for the first time the Programme number (PR) on the screen shows two dashes and is highlighted white. Set it to be the same as the PR number to which your broadcasting channel is set into. For instance if you can view CH 47 on programme (PR) 47, set the On screen PR number to 47.

• You need to set this only once.

• If the channels are retuned you need to set the PR numbers again.

PR: Preset Channel

” lights on the VCR Front Panel

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

1/2 DATE PR START STOP 15/12 -- 12:00 12:30 SP

--/-- -- -:-- -:-- --

PR :PRESET CH :SELECT :CHANGE SET:ENTER MENU:EXIT

PMPM

VCR/DVD COMBINATION

Recording with the Timer

The timer can be set manually for automatic recording of up to 8 events over a 365 day period.

Preparation

• Load the cassette, ensuring the erasure protection hole is covered. The Product power will automatically turn on.

• Check that the clock is displaying the correct time. (See “Setting the Clock” on page 35.)

• Be sure that the colour mode is set to “AUTO”. (See “COLOUR” on page 55.)

For DV-NC70 and DV-NC70X model: Press PROG on the Remote to enter the Timer setting screen.

1 Press VCR MENU. Then select “TIMER” with ' / " and press

SET.

MENU G-CODE

TIMER

MODE CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

2 Select the timer position with ' / " and press SET.

• If the timer positions 1 to 4 have already been set, the screen changes to 2/2 (timer positions 5 to 8).

1/2 DATE PR START STOP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- - 2/2

:SELECT SET:ENTER MENU:EXIT

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

3 Set the date for timer recording with the number buttons (0 to 9)

or ' / " on the Remote and press

First set the “day” digits and then “month”. If there is only one

•

“day” or one “month” digit, enter a 0 first.

1/2 DATE PR START STOP

15/12 -- -:-- -:-- SP

--/-- -- -:-- -:-- --

DATE :DAY/MONTH :SELECT :CHANGE SET:ENTER MENU:EXIT

“SP” will be displayed automatically.

VCR/DVD COMBINATION

Recording with the Timer

4 If you want to record only once, press

| and go to step 5.

Otherwise, select “D (DAIL Y)” to record at the same time each day or “W (WEEKLY)” to record at the same time each week with ' / ", and then pressing

1/2 DATE PR START STOP 15/12 -- -:-- -:-- SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- - :ONCE

W:WEEKLY D:DAILY

:SELECT :CHANGE SET:ENTER MENU:EXIT

5 Set the channel number using the number buttons (0 to 9) or

' / " and press

To record audio and video from an external source through an

•

AUDIO/VIDEO terminal on the Product. Press AV channel. (When an AV position is selected, “L1” or “L2” is displayed where a channel position number is usually displayed.)

• ' /" can also be used to set the date and time instead of the number buttons (0 to 9).

• Press 0 first if the day, month, hour or minute is a single digit.

Set the start time with the number buttons

press

1/2 DATE PR START STOP 15/12 471 -:--PM -:-- SP

--/-- -- -:-- -:-- --

' / " to select an

(0 to 9)

or ' / " and

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

1/2 DATE PR START STOP 15/12 47 12:00

--/-- -- -:-- -:-- --

Set the stop time with the number buttons

press

1/2 DATE PR START STOP 15/12 47 12:00

--/-- -- -:-- -:-- --

-:-- SP

When the clock is set to 24H mode, AM/PM indicator will not appear

12:30PMSP

(0 to 9)

or ' / " and

VCR/DVD COMBINATION

VCR

Recording with the Timer

8 Select the speed with

' / "

1/2 DATE PR START STOP 15/12 47 12:00

--/-- -- -:-- -:-- --

12:30PMSP

• SP: Standard Play, LP: Long Play, EP: Extended Play

9 Press SET. T o programme additional timer settings, repeat steps

3 through 8.

1/2 DATE PR START STOP 15/12 47 12:00 12:30 SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- - 2/2 CLEAR:CANCEL :SELECT SET:ENTER MENU:EXIT

PMPM

10 Press VCR MENU to return to the normal screen. 11 To set the product for automatic timer recording, press TIMER

ON/OFF and ensure the “

display.

VCR

L R

SEPVP D

” lights on the VCR Front Panel

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

• If the timer recording is finished, your product will stop and turn off automatically. (In this case the cassette is not ejected.) If a DVD is being played back, the power will not turn off. (The timer recording is stopped while the power stays on.)

• If the cassette runs out during the timer recording, your product will eject the cassette without rewinding. In this case, the timer recording is cancelled (“ ” disappears) and the device turns itself off automatically. However, if a DVD is being played back, the power will not turn off. (The power stays on.)

• If power is interrupted for more than 60 minutes (power failure, etc.), all timer settings will be cancelled.

• If TIMER ON/OFF is pressed when there is no cassette loaded, “ ” flashes for 5 seconds, indicating that timer recording is not possible.

• If TIMER ON/OFF is pr essed while a cassette with an uncover ed erasure protection hole is loaded, “ ” flashes and the cassette is ejected.

• When “ ” is lit, regular VCR operation, clock setting and setting/ cancelling/confirming timer positions are not possible. For regular VCR operation, clock setting and setting/cancelling/confirming timer positions, press TIMER ON/OFF to disengage the timer (“ ” disappears), and then turn on your Product.

• During timer recording, the timer cannot be set.

• To terminate timer recording, press ËSTOP during timer recording.

• If the same time is input for the start time and the stop time, the timer

setting will be cancelled.

VCR/DVD COMBINATION

Confirming Timer Programmes

You can see on the On Screen Display a list of all timer programmes that are already set.

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR and select the video channel on the TV.

Recording with the Timer

DV- NC70W DV- NC70

DV- NC70X

G-CODE

PROG

1 Press VCR MENU. (If the “ ” indicator on the VCR Front Panel

display is lit, cancel the timer standby mode with and then turn on the power.)

TIMER ON/OFF

2 Select “TIMER” with ' / " and then press SET to confirm .

MENU G-CODE

TIMER

MODE CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

3 The screen for confirming programmes that have been set will

appear.

1/2 DATE PR START STOP 15/12 47 12:00 12:30 SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- - 2/2

:SELECT SET:ENTER MENU:EXIT

• Check the information displayed. If you want to correct the data, select the programme to be

•

changed with

' / "

and press SET. Correct the setting as

described on pages 72.

PMPM

TIMER

OPERATE

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

INPUT SELECT

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

•

After the data is changed, press SET at the applicable tape-speed position at right.

4 Press VCR MENU to return to the normal screen.

• After checking or correcting the programme contents, press

TIMER ON/OFF to enter the Timer Standby mode.

Recording with the Timer

Cancelling Timer Programmes

Perform the following procedure to cancel timer programmes that have already been set.

Preparation

• Press OPERATE. Then move the VCR/DVD CHANGE Switch to VCR and select the video channel on the TV.

DV- NC70W

DV- NC70

DV- NC70X

G-CODE

PROG

1 Press VCR MENU. (If the “ ” indicator on the VCR Front Panel

display is lit, cancel the timer standby mode with and then turn on the power.)

TIMER ON/OFF

2 Select “TIMER” with ' / " and then press SET to confirm .

MENU G-CODE

TIMER

MODE CHANNEL PRESET CLOCK LANGUAGE

:SELECT

SET:ENTER MENU:EXIT

3 The screen for confirming programmes that have been set will

appear.

• Select the programme you wish to cancel with ' / ". (The selected programme will appear highlighted.)

1/2 DATE PR START STOP

15/12 48 12:00 12:30 SP

--/-- -- -:-- -:-- --

--/-- -- -:-- -:-- - 2/2

:SELECT SET:ENTER MENU:EXIT

PMPM

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

4 Double-check that it is the programme you wish to cancel, and

press CLEAR. It will be cleared on the screen.

1/2 2/2 DATE PR START STOP

--/-- -- -:-- -:-- --

:SELECT SET:ENTER MENU:EXIT

5 Press VCR MENU to return to the normal screen.

• If there are still some programmes to be set, press TIMER ON/OFF to enter the Timer Standby mode.

VCR/DVD COMBINATION

Tape Dubbing

Tape Dubbing Connection Instructions

Your product can dub (copy) video material from another video device. It can also output video and audio signals for recording on other video or audio equipment. Audio/Video dubbing cannot be done separately.

1 Switch your product to the auxiliary input by pressing INPUT

SELECT. “L1” lights up on the VCR Front Panel display. (You can also use CH ' / ".)

2 Begin recording on the dubbing VCR and playback on the

source VCR simultaneously.

• When using special playback functions (still picture, video search, frame advance, and variable slow motion) during dubbing, a blue screen may appear. Set BLUE SCREEN mode on the dubbing VCR (for recording) to OFF. (See Mode Selection on page 25.)

• Use an RCA pin–type connection cable (not supplied with VCR, but supplied with VIEWCAM) to connect source VCR to dubbing VCR.

• Refer to the manual of the VCR connected to this product when dubbing a tape.

• You can also use the front AV jacks. Select “L2” (Aux. 2 input) by pressing INPUT SELECT twice.

• If source VCR is a monaural mode, connect the audio cable to “AUDIO-L” of the dubbing VCR.

TIMER

OPERATE

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

LINE IN 1

AUDIO

VIDEO

VCR

ANTENNA IN

DVD/VCR LINE OUT 1

AUDIO

VIDEO

Source VCR

(for playback)

RF OUT

DVD/VCR

LINE OUT 1

AUDIO

VIDEO

LINE IN 1

AUDIO

VIDEO

Sharp Viewcam

(for playback)

Audio/Video cable (supplied with Viewcam)

VCR

ANTENNA IN

RF OUT

Dubbing VCR

(for recording)

VCR/DVD COMBINATION

AV 2 IN VIDEO L(MONO) - AUDIO-R

To Front

Recording a DVD Disc onto a Video Cassette

Use the following procedure to record the images and sounds on a DVD disc onto a video cassette.

PLAY/×2

OPERATE

REW

EJECT/STOP

REC

Recording a DVD disc onto a Video cassette (Tape Editing mode)

(

)

AV 2 IN

MONO

VIDEO

AUDIO-R

PLAY STOP

VCR/DVD SELECTOR

TIMER

VCR

OPEN/CLOSE

DVD

Preparation

• Turn on the TV and switch to the external “VIDEO” or “AV” channel.

This Product

• Press OPERATE.

• Move the VCR/DVD CHANGE Switch on the Remote to VCR.

1 Insert both the DVD disc and the video cassette for recording.

2 Press VCR

• The VCR

\ DVD.

\\ \\

\ DVD indicator lights up.

3 Move the VCR/DVD CHANGE Switch on the Remote to DVD.

4 Press ON SCREEN to turn off the DVD on screen display (See

page 49).

5 Press ûPLAY.

• The disc start playback.

• In DVD to VCR recording mode, some discs cannot be recorded:

1 Discs with copy guard function

OPERATE

FUNCTION

CONTROL

CLEAR

RETURN

VCR DVD indicator

DV- NC70W DV- NC70

DV- NC70X

TIMER

ON/OFF

VCR/DVD

DISPLAY

SCREEN

PROG/

REPEAT

TITLE

REV FWD

REC

TAPE

SPEED

SELECTOR

ANGLE

INPUT SELECT

PLAY

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR MENU

DVD SETUP

OPEN/

DVD MENU

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

EJECT

SET

ENTER

SLOW

PLAY

G-CODE

PROG

VCR/DVD COMBINATION

Recording a DVD Disc onto a Video Cassette

6 Press

ÆÆ

ÆREC.

ÆÆ

• The images on the DVD disc are recorded onto the VCR cassette.

• When the VCR is in stop mode, the channel returns to the previously received channel.

• The VCR/DVD SELECTOR is fixed to VCR in the Tape Editing mode (VCR\ DVD indicator lights up).

• Operate the VCR/DVD SELECTOR after pressing VCR

\ DVD,

and after the Tape Editing mode has been cleared (VCR\ DVD indicator stops lighting up).

• The following are not signs of trouble.

1 The brightness of images from regular DVD disc playback and

from discs played in Tape Editing mode might vary.

2 The discs playing time and the Real time counter slightly vary when

recording.

• The DVD/VCR output jacks become VCR fixed.

• The following operations cancel the DVD/VCR output and return to the

regular external input.

1 Programming the timer. 2 Setting the recording ending time during Pause. 3 Turning OPERATE on or off after entering the Tape Editing mode.

• Copy protected DVD discs cannot be recorded (The image will be

distorted, when

• If the DVD on screen display is “ON” while recording, the display will

also be recorded.

The recordings, which you make from TV/radio broadcasts or audio sources (such as records) are for your own private use, and cannot be used without prior permission or consent of the author.

ÆÆ

ÆREC is pressed).

ÆÆ

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

Watching the DVD

Preparing to Use DVD..................................................................... 78

When connecting a TV with the DVD output Jacks ....................... 78

When connecting a TV with the DVD/VCR shared output jacks.... 78

Playback .......................................................................................... 79

Basic Play ...................................................................................... 79

Track Direct Playback .................................................................... 79

Fast Forward/Fast Reverse ........................................................... 80

Slow-Motion Play ........................................................................... 80

Still/Pause ...................................................................................... 81

Frame Advance.............................................................................. 81

Skip (Forward/Reverse) ................................................................. 81

Angle Selection ............................................................................... 82

Playing MP3 Discs .......................................................................... 83

Regarding MP3 discs..................................................................... 83

Playing MP3 discs.......................................................................... 83

To play MP3 discs .......................................................................... 84

To play another file (music title) while playing................................ 84

To skip the file while playing........................................................... 84

About the Function Control Screen .............................................. 85

Direct skip (title [track]/chapter/time).............................................. 86

Subtitle language setting................................................................ 87

Angle setting .................................................................................. 88

Audio setting .................................................................................. 89

3D VIRTUAL SURROUND setting................................................. 90

DIGITAL GAMMA setting ............................................................... 91

Direct Selection of Scenes............................................................. 92

Selecting Scenes by Title Number................................................. 92

Selecting Scenes from the Menu Screen....................................... 92

Programmed Playback ................................................................... 93

Chapter Programmed Playback..................................................... 93

Track Programmed Playback......................................................... 94

MP3 Files Programmed Playback.................................................. 95

Repeat Playback ............................................................................. 96

Repeat playback ............................................................................ 96

A-B Repeat .................................................................................... 97

Resume Function............................................................................ 98

WATCHING

THE DVD

Preparing to Use DVD

The following steps are necessary to display the DVD screen on the TV.

When connecting a TV with the DVD output jacks

1 Turn on the TV and switch the TV channel to the external input

“VIDEO” or “AV” channel connected to DVD output jack.

2 Press OPERATE.

• The start up screen is displayed on the TV screen.

REW

OPERATE

EJECT/STOP

PLAY/×2

)

AV 2 IN

L(MONO

AUDIO-R

VIDEO

OPERATE

PLAY STOP

REC

VCR/DVD

SELECTOR

VCR/DVD SELECTOR

TIMER

DVD

VCR

VCR/DVD

SELECTOR

OPEN/CLOSE

3 Move VCR/DVD CHANGE Switch on the Remote to DVD.

VCR DVD

• When the TV is connected to the DVD output jack, the image will be

displayed regardless of the VCR/DVD mode selected. Therefore, it is not necessary to adjust the mode selected.

When connecting a TV with the DVD/VCR shared output jacks

Turn on the TV and switch the TV channel to the external input “VIDEO” or “AV” channel connected to DVD/VCR shared output jack.

2 Press OPERATE. 3 Move VCR/DVD CHANGE Switch on the Remote to DVD.

VCR DVD

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

4 Press VCR/DVD SELECTOR to enter the DVD mode.

• The VCR/DVD SELECTOR on the product lights up in green.

VCR/DVD SELECTOR

Light up in green

Each time VCR/DVD SELECTOR is pressed, the mode

•

changes between “VCR” mode and “DVD” mode.

VCR/DVD COMBINATION

Playback

Preparation

• See Preparing to Use DVD on page 78.

VIDEO

DVD

C D

CD-R/RW

• The icons below are used in this Operation Manual:

DVD

................... Indicates the functions that can be performed

for DVDs.

C D

................... Indicates the functions that can be performed

for AUDIO CDs.

CD-R/RW

VIDEO

............... Indicates the functions that can be performed

for CD-R/RW.

C D

.................... Indicates the functions that can be performed

for VIDEO CD.

Basic Play

1 Press OPERATE. 2 Press îOPEN/CLOSE to open the disc tray. 3 Place a disc onto the tray.

• Hold the disc without touching either of its surfaces, position it with the printed title side facing up, align it with the guides, and place it in its proper position. 1 8 cm (3") disc 2 12 cm (5") disc

• Do not stack discs in the tray. This can damage the player and the discs.

4 Press î OPEN/CLOSE to close the disc tray. 5 Press ûPLAY.

• Playback image appears on the screen. (No image is shown for audio CDs.)

6 Press ËSTOP to stop playback.

VIDEO

C D

OPERATE

REW

EJECT/STOP

OPERATE

)

AV 2 IN

L(MONO

AUDIO-R

VIDEO

Disc

PLAY/×2

REC

E M I T

V D

R C

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

OPEN/CLOSE

1 2

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

OPEN/CLOSE

VCR/DVD SELECTOR

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR/DVD

VCR MENU

SELECTOR

DVD SETUP

OPEN/

ANGLE

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

PLAY STOP

TIMER

DVD

VCR

OPEN/CLOSE

STOP

PLAY

G-CODE

PROG

Playing VIDEO CDs with Playback Control (PBC)

• Pressing ûPLAY begins PBC playback. Time display is not shown for some discs.

• If you specify the track number to be played (with playback stopped) and press ûPLAY, normal playback (not PBC playback) begins.

• If the disc is loaded upside down or is damaged, “– – – – –” appears on the DVD Front Panel display and the disc tray slides out.

• If you attempt to play a DVD disc with the wrong region code, “ REGION CODE ERROR” appears on the TV screen and the disc tray slides out.

VIDEO

C D

CD-R/RW

VIDEO

C D

Track Direct Playback

1 To display the title number you want to watch, press the number

buttons (0 to 9) on the Remote while playing or stopping an image.

2 Press ûPlay.

• The track number you entered in step 1 is played.

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

Playback

VIDEO

DVD

C D

CD-R/RW

VIDEO

C D

Fast Forward/Fast Reverse

DVD

or ÈREV during playback.

Scanning speed selection

Fast scan image appears here. (No image is shown for Audio CDs.)

1 Press FWD

• The disc begins fast scan at ×2 speed (1).

• Three speeds are available for DVD, VIDEO CDs and Audio

CDs. Each time FWDè or ÈREV is pressed, the speed of fast scan changes in the following sequence:

1 (about ×2) 2 (about ×8) 3 (about ×32)

2 Press ûPLAY when you reach the desired point.

• On some discs, the fast scan function is disabled.

• On DVD discs, audio and subtitles are not played back during the fast

scan playback. Audio is played back only when the search speed of the fast forward is 1 (about ×2).

• With a DVD disc, you cannot search past a title. Playback starts from the beginning of the title.

• Depending on the audio equipment, the sound may not come out when the fast forward is 1 (about ×2).

VIDEO

DVD

VIDEO

C D

Slow-Motion Play

1 Press SLOW in the play mode or still mode.

• Three speeds are available. Each time SLOW is pressed, the speed of slow-motion playback changes in the following sequence:

(DVD)

1 (about ×1/2) 2 (about ×1/8) 3 (about ×1/16)

PLAY STOP

PLAY/×2

OPERATE

REW

EJECT/STOP

REC

)

AV 2 IN

L(MONO

AUDIO-R

VIDEO

VCR/DVD SELECTOR

TIMER

VCR

OPEN/CLOSE

DVD

PLAY

G-CODE

PROG

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

2 Press ûPLAY to return to the normal playback or press

PAUSE/STILL to return to the still picture mode.

• On some discs, the slow-motion playback functions are disabled.

• Slow-motion playback is disabled on Audio CDs and MP3 discs.

VCR/DVD COMBINATION

VIDEO

DVD

C D

CD-R/RW

VIDEO

C D

Still/Pause

Press âPAUSE/STILL during playback.

1 2 If you press ûPLAY while paused (STILL/PAUSE), normal

playback resumes.

VIDEO

DVD

VIDEO

C D

Frame Advance

Press âPAUSE/STILL during playback.

• The playback is paused (STILL/PAUSE).

• The disc goes forward by one frame each time

PAUSE/STILL is pressed.

2 Press ûPLAY to return to the normal playback.

VIDEO

DVD

C D

CD-R/RW

VIDEO

C D

Skip (Forward/Reverse)

While you are playing a disc, this function jumps to the beginning of the next chapter/track (Forward) or the current chapter/track (Reverse) and automatically starts playing that chapter/track.

1 While a disc is playing, press SKIPà or

• Playback skips forwards one chapter/track for each time

SKIPà is pressed.

• If you press ÀSKIP and playback begins, and you then press ÀSKIP again within 3 seconds, playback returns to the beginning of the previous chapter/track.

• The frame advance playback functions are disabled for audio CDs and MP3 discs.

• On discs or titles that do not have chapter settings, playback skips forward to the next title or back to the beginning of the current title or disc.

• On some discs, the skip functions are disabled.

• The playback image is not displayed during the skip. It resumes

during playback following the skip.

When VIDEO CDs are played in PBC mode:

• Pressing SKIPà causes the disc to move to the NEXT position.

• Pressing ÀSKIP causes the disc to move to the PREVIOUS position.

SKIP.

Playback

PLAY STOP

PLAY/×2

REW

EJECT/STOP

OPERATE

AV 2 IN

VIDEO

REC

)

L(MONO

AUDIO-R

VCR/DVD SELECTOR

TIMER

DVD

VCR

OPEN/CLOSE

PLAY

G-CODE

PROG

TIMER

OPERATE

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

INPUT SELECT

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

DVD

Angle Selection

DVD

Some DVD discs contain scenes which have been shot simultaneously from a number of different angles. For these discs, the same scene can be viewed from each of these different angles. (The recorded angles differ depending on the disc used.)

1 While you are playing a DVD disc with different angles recorded,

press ANGLE to view the number of the current angle.

Number changes to show the number of the current angle. (The maximum number stipulated by the manufacturers is 9.)

Lights when different angles are recorded for the title currently playing.

2 Use ' or " (or ANGLE) to change the scene to the next angle

in those recorded.

• About two seconds later, playback continues from the new angle you selected.

• If no button is pressed within 10 seconds, playback continues without changing the current angle.

Sequence of angle shots

(Example)

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

• This function can only be used for discs on which scenes shot from multiple angles have been recorded.

• If no angles are recorded on the disc, xx is displayed.

VCR/DVD COMBINATION

Playing MP3 Discs

This product is able to play CD-R or CD-RW discs recorded in MP3 format.

Regarding MP3 discs

•

MP3 files are audio data compressed in MPEG1 Audio layer 3 file format. “MP3 files” have “.mp3” as extensions. (Some files that have “.mp3” extensions or files that have not been recorded in MP3 format will produce noise or cannot be played.)

• Some discs cannot be played depending on the actual CD-R/CD-RW disc condition, the recording equipment and the disc’s recording.

• Data on the CD-R or CD-RW disc, which has not been recorded in MP3 format, audio tracks or has been recorded in other file formats except MP3, cannot be played.

Playing MP3 discs

• Discs that have more than 255 folders and files in total cannot be played.

• Some MP3 files are not played in the order they were recorded.

• The number of layers, which can be recognized, including files and folders, is maximum 8.

• Only the first session of a multi-session disc can be played.

• When both audio tracks and MP3 files are recorded on a disc, audio tracks will be played.

• Depending on the folder tree, reading MP3 files can take time.

• The more files there are, the longer the reading time. Therefore it is recommended to lower the number of

folders before recording.

• Folder or track (file) names are limited to 8 characters. The folder / file names are displayed in half-size, capital letters or half-size numbers. Folder or track (file) names that go over 8 characters will be abbreviated.

• Certain letters or symbols in folder names or file names may not be displayed. In this case, “?” will be displayed.

• The playing time may not be correctly displayed during MP3 file playback.

• It is recommended to record data at a lower speed as data recorded at fast speed can produce noise and

may not be able to be played.

CAUTION

• It is impossible to make a digital copy by using a digital audio recording device which outputs sound from discs in MP3 format through the coaxial digital output jack of this product.

Playing MP3 Discs

To play MP3 discs

Load the MP3 recorded CD-R or the CD-RW.

• The folder selection screen will be displayed after the data is read.

1/ 4

FOLDER1 FOLDER2 FOLDER3 FOLDER4

MP3

2 Select the folder you want to play by using ', ", \ or | and

then press ENTER.

• The file (music title) in the folder is displayed on the file selection screen.

FOLDER1

1 TITLE01 2 TITLE02 3 TITLE03 4 TITLE04

MP3

• Press RETURN to return to the folder selection screen.

• When pressing |PLAY after selecting the folder, the

playback screen is displayed, and the files in that folder can be played from the beginning.

3 Select the file (music title) you want to play by using ', ", \ or

| and then press ENTER.

• The chosen file (music title) will be played in sequence.

FOLDER1

1 TITLE01 2 TITLE02 3 TITLE03 4 TITLE04 5 TITLE05 6 TITLE06 7 TITLE07 8 TITLE08

FOLDER1 7 TITLE07

MP3

4 Press ËSTOP to stop play.

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

To play another file (music title) while playing

1 Press ', ", \ , | to select the file (music title) you want to play

and then press ENTER.

• The chosen file (music title) will be played.

• The file where the cursor is on, will be played when the cursor is

moved to a different from the file being played and no operation is taken within 10 seconds.

• Press RETURN to return to the folder selection screen.

To skip the file while playing

Press SKIPà or ÀSKIP during playback.

• SKIPà will skip forward, and ÀSKIP will rewind.

• When playing files (tracks) from other folders, press RETURN

and then select the files from the folder selection screen.

While the MP3 disc is playing

• Time Search is disabled.

• Programmed playback is disabled.

• It is possible to repeat one track or the entire folder.

VCR/DVD COMBINATION

About the Function Control Screen

Using Function control, you can check at a glance and change the current settings of the following items: SUBTITLE, ANGLE, AUDIO, 3D VIRTUAL SURROUND and, DIGITAL GAMMA. Function control also allows you three ways of direct skips (title [track], chapter and time).

• While the disc is playing, press FUNCTION CONTROL to display the screen shown below.

• Pressing ' or " changes the currently selected item.

• Numbers in

refer to the pages where the setting procedures are described.

1 Direct title skip

Direct chapter skip Direct time skip

Currently selected item

2/5

8/3‰

‰1:3‰:‰8

Subtitle Angle

ENGLISH

2 1 1

1 Direct title skip

• The number of the title currently played back is

• You can skip directly to the desired title.

2 Direct chapter skip

• The number of the chapter currently played back is

• You can skip directly to the desired chapter.

3 Direct time skip

•

• You can skip directly to the point fr om which you want

4 Subtitle setting

• The subtitle number and language currently selected

• You can select the desired subtitle language.

5 Angle setting

• The current angle is displayed. (When a disc with

• You can select the desired angle.

Audio 3D VIRTUAL

SURROUND DIGIT AL GAMMA

displayed.

Elapsed time from the beginning of the disc is displayed.

to start playback.

are displayed. (When a disc with only one subtitle is played back, xx is displayed.)

only one angle is played back, xx is displayed.)

DVD

BIT RATE indicates the amount of data that is

5 1ch

05 10

BIT RATE

Mbps

SELECT

ENTER

6 Audio setting

•

The type of audio currently selected is displayed.

• You can select the desired type of audio.

7 3D VIRTUAL SURROUND setting

• This function provides rich surround sound by downmixing Dolby Digital 5.1 channel and Dolby Surround (Pro Logic) to 2-channel audio or TV.

• You can toggle the setting between “ON” and “OFF”, and change the level.

• When “COMPRESSION” is “ON”, this function is disabled, which is indicated by xx. To use the 3D VIRTUAL SURROUND function, set the “COMPRESSION” to “OFF” (see page 44).

8 DIGITAL GAMMA setting

• You can make the entire image easier to see by brightening the darker and obscure portions.

• You can toggle the setting between “ON” and “OFF”, and change the level.

RETURN

being transferred to the product per second. However, note that picture quality is not always in proportion to the bit rate.

• In Function control mode, you can return to the previous setting screen by pressing RETURN or FUNCTION CONTROL.

• You can cancel the Function control mode by pressing ËSTOP, DVD MENU or TITLE.

• The setting screen is cleared automatically whenever you display a DVD screen that prompts you to change the

scene by pressing ', ", \, or |.

About the Function Control Screen

VIDEO

DVD

C D

VIDEO

C D

Direct skip (title [track]/chapter/time)

Use the following procedure to perform the Direct title [track] skip, Direct chapter skip, or Direct time skip.

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

2 Use ' or " to select and then press ENTER.

(Example) Direct title skip

--/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

3 Use number buttons (0 to 9) to input the title number to which

you want to skip.

• You can also use ' or " to input the title number.

(Example) Entering title 5

5/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

4 Press ENTER.

• The played back image changes to the beginning of the specified title.

• You can exit the Function control screen by pressing RETURN or FUNCTION CONTROL.

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

• The number of titles, chapters or times you can input depends on that of the titles, chapters or times recorded on a disc you play.

• Direct chapter skip can only be used for DVD discs.

DVD

Subtitle language setting

Use the following procedure to perform the Subtitle language setting.

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

About the Function Control Screen

G-CODE

PROG

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

2 Use ' or " to select and then press ENTER.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

Mbps

SELECT

RETURN

3 Press ' or " to select the subtitle language you want to use.

• You can set the subtitle setting to “OFF”.

• You can also toggle the setting between “ON” and “OFF” by

pressing \ or |.

(Example) Selecting “3 SPANISH”

2/5

8/3‰

‰1:3‰:‰8

SPANISH

3 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

Mbps

SELECT

RETURN

4 Press ENTER to confirm the setting.

• You can exit the Function control screen by pressing

RETURN or FUNCTION CONTROL.

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

• This function can only be used for discs on which subtitles have been recorded in multiple languages.

• Some DVD discs are marked “Forced Display”, indicating that the subtitling cannot be suppressed. With such discs, the subtitles will be displayed even when you select “ OFF” display. This does not indicate a fault with this product.

• If no subtitles are recorded on the disc, xx is displayed.

About the Function Control Screen

DVD

Angle setting

You can change the angle of view when playing a DVD disc that contains scenes recorded from multiple angles. Use the following procedure to perform the Angle setting.

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

2 Use ' or " to select and then press ENTER.

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

G-CODE

PROG

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

3 Press ' or " to select the angle number you want.

• The number of recorded angles differs depending on the disc used.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 2 1 ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

4 Press ENTER to confirm the setting.

• You can exit the Function control screen by pressing RETURN or

FUNCTION CONTROL.

• This function can only be used for discs on which scenes shot from multiple angles have been recorded.

• If no angles are recorded on the disc, xx is displayed.

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

VIDEO

DVD

VIDEO

C D

Audio setting

A number of different methods are used to record audio onto a DVD disc, including multi-channels (used for voiceovers in other languages), Dolby Digital (5.1ch), DTS, and Linear PCM. This product provides a number of different audio modes from which you can choose to suit the type of disc you are playing. Use the following procedure to perform the Audio setting.

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

2 Use ' or " to select and then press ENTER.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

3 Press ' or " to select the audio format you want to use.

• See page 44 for details about the types of audio format.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 2LPCM ON

5.1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

About the Function Control Screen

G-CODE

PROG

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

• When watching the video CD, the audio channels changes as the

following sequence:

L+R L R

4 Press ENTER to confirm the setting.

• You can exit the Function control screen by pressing RETURN or

FUNCTION CONTROL.

• This function can only be used for discs on which the sound has been recorded in multiple formats.

• With certain types of discs, you can change the audio using the disc menu. (See page 44.)

• A DTS digital surround decoder is required to listen to DTS audio.

About the Function Control Screen

DVD

3D VIRTUAL SURROUND setting

This function allows you to enjoy a “surround sound” effect when you are using an analog connection (using AV 1 OUT on this product) to 2-channel audio equipment (TV, etc.).

Preparation

To use the 3D VIRTUAL SURROUND function

Set the “COMPRESSION” setting in “AUDIO” to “OFF” (see page 44).

•

Refer to the table below about the types of audio format with which 3D VIRTUAL SURROUND works.

Types of audio recorded on the disc

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

G-CODE

PROG

Dolby

Digital

Dolby

Pro Logic

Dolby Digital

2ch/Linear

PCM

DTS

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

2 Use ' or " to select and then press ENTER.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

SELECT

RETURN

Mbps

3 Press ' or " to toggle 3D VIRTUAL SURROUND between

“ON” and “OFF”.

4 While “ON” is selected, use \ or | to change the level setting.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

Mbps

SELECT

RETURN

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

• 3D VIRTUAL SURROUND does not operate on Audio CDs.

• 3D VIRTUAL SURROUND does not operate when you set the “COMPRESSION” setting in “AUDIO SETUP” to “ON”.

• 3D VIRTUAL SURROUND does not operate when you are using a Digital connection.

• 3D VIRTUAL SURROUND does not operate when you playback a disc recorded using DTS format.

5 Press ENTER to confirm the setting.

• You can exit the Function control screen by pressing

RETURN or FUNCTION CONTROL.

VIDEO

DVD

VIDEO

C D

DIGITAL GAMMA setting

DIGITAL GAMMA is a digital image quality enhancement function that gives a richer image by brightening the darker and more obscure portions of the image without altering the brightness of the brighter portions, thereby making the entire image easier to see. Three digital gamma settings are available to allow for differences in the images played and in brightness of the room.

1 Press FUNCTION CONTROL during playback.

• The Function control screen appears.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5 1ch

BIT RATE

ENTER

SELECT ENTER

DVD

05 10

Mbps

RETURN

2 Use ' or " to select and then press ENTER.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

Mbps

SELECT

RETURN

3 Press ' or " to toggle DIGITAL GAMMA between “ON” and

“OFF”.

4 While the “

• The level selection indicator that shows the current level appears.

ON” is displayed, press \ or |.

About the Function Control Screen

G-CODE

PROG

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

5 Use \ or | to change the level.

2/5

8/3‰

‰1:3‰:‰8

ENGLISH

2 1 1 ON

5.1ch

BIT RATE

ENTER

DVD

05 10

Mbps

SELECT

RETURN

6 Press ENTER to confirm the setting.

•

You can exit the Function control screen by pressing RETURN or FUNCTION CONTROL

VCR/DVD COMBINATION

Direct Selection of Scenes

DVD

Selecting Scenes by Title Number

Press TITLE to show the title screen. (Example)

DISCOVERY EUROPE

DISCOVERY AFRICA

2 Use ', ", | or \ to highlight the desired title.

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

3 When you press ENTER or û PLAY, the title specified in step 2

starts playing.

Selecting Scenes from the Menu Screen

Press DVD MENU to show the menu screen. (Example)

T I T L E

tas

gos

sihes

2 Use ', ", | or \ to highlight the desired title.

(Example) Title 2 selected.

T I T L E

1 2

tas

gos

sihes

3 When you press ENTER or û PLAY, title 2 starts playing.

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

• These functions only operate on DVD discs that have a title or menu screen.

• Languages not provided on the disc are not displayed.

Programmed Playback

The two types of programmed playback provided by this product are chapter programmed playback (DVD discs) and track programmed playback (Audio CD discs).

DVD

Chapter Programmed Playback

Press PROG while the disc is stopped.

• The “DVD-VIDEO PROGRAM” screen appears.

• Press PROG to return to the normal screen.

DVD-VIDEO PROGRAM

TITLE

1 2 3

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

ENTER

SELECT

SET

2 Press ' or " to select the desired title and then press ENTER.

• The chapter selection screen appears.

DVD-VIDEO PROGRAM

: 2 : 2

1 1: 2 2: 3 3: 4: 5: 6:

SELECT

START

RETURN

3 Press ' or " to select the desired chapter and press ENTER.

• The chapter is programed in the playlist.

DVD-VIDEO PROGRAM

: 2 : 2

1 1: 3 2 2: 1 3 3: 4: 5: 6:

SELECT

START

RETURN

• Repeat the above step for each of the chapters that you want to play as part of the program.

• To delete the chapter programmed in the playlist, follow the steps below.

1 Press | to move the cursor to the playlist. 2 Press ' or " to select the program (chapter) you want to

delete and then press RETURN.

• To delete all programmed chapters, move the cursor to the playlist and then press RETURN for more than two seconds.

4 Press ûPLAY to begin playing the programmed chapters.

• The chapters will be played in the order they were entered.

• The PROGRAM indicator lights up on the DVD Front Panel

display.

5 Press

ËË

ËSTOP to stop programmed playback.

ËË

• To start programmed playback again, follow the steps below.

1 Press

ËË

ËSTOP to stop programmed playback.

ËË

2 Press PROG. 3 Select the title you programmed and press ENTER. (If

other titles are selected, the previously entered program will be cleared.)

4 Press ûPLAY.

CLEAR

RETURN

INPUT SELECT

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

•

Up to 24 chapters can be programmed.

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

• Press RETURN to return to the previous screen.

• The program cannot be set during the normal playback.

• This function can only be used for DVD discs on which the chapter has been recorded.

• On some discs in which programmed playback is prohibited, this function is disabled.

Programmed Playback

VIDEO

C D

VIDEO

C D

T rack Programmed Playback

Press PROG while the disc is stopped.

• The “PROGRAM” screen appears.

• Press PROG to return to the normal screen.

Example : CD PROGRAM screen

PROGRAM

START

: : : : : :

SELECT

1 1 2 2 3 3 4 4 5 5 6 6

2 Press ' or " to select the desired track and then press ENTER.

• The track is programmed in the playlist.

PROGRAM

1 1: 2 2: 3 3 4 4 5 5 6 6

SELECT

START

2 : : : :

3 Repeat step 2 for each of the tracks that you want to play as part

of the program.

4 Press ûPLAY to begin playing the programmed tracks.

• The tracks will be played in the order they were entered.

5 Press

ËË

ËSTOP to stop programmed playback.

ËË

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

• Up to 24 tracks can be programmed.

• Press RETURN to return to the previous screen.

• The program cannot be set during the normal playback.

• On some discs in which programmed playback is prohibited, this

function is disabled.

VCR/DVD COMBINATION

CD-R/RW

MP3 Files Programmed Playback

Press PROG while the disc is stopped.

• The “MP3 PROGRAM” screen appears.

• Press PROG to return to the normal screen.

MP3 PROGRAM : 1/ 4

SET

: : : : : :

FOLDER1 1 FOLDER2 2 FOLDER3 3 FOLDER4 4

FOLDER4 5 FOLDER4 6

SELECT

ENTER

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

Programmed Playback

DV- NC70W

DV- NC70

DV- NC70X

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

G-CODE

PROG

2 Press ' or " to select the desired folder and then press

ENTER.

MP3 PROGRAM

FOLDER1

TITLE01 1 TITLE02 2 TITLE03 3 TITLE04 4 TITLE05 5 TITLE06 6

SELECT

START

: : : : : :

RETURN

3 Press ' or " to select the desired file and press ENTER.

• The file is programed in the playlist.

• Press RETURN to return to step 2 and then select the files of

other folder.

MP3 PROGRAM

FOLDER1

TITLE01 1:TITLE03 TITLE02 2:TITLE04 TITLE03 3:TITLE01 TITLE04 4 TITLE05 5 TITLE06 6

SELECT

START

: : :

RETURN

• Repeat the above step for each of the files that you want to play as part of the program.

• To delete the files programmed in the playlist, follow the steps below.

1 Press | to move the cursor to the playlist. 2 Press ' or " to select the program (track/file) you want to

delete and then press RETURN.

To delete all programmed chapter number, move the cursor to

•

the playlist and then press RETURN for more than two seconds.

4 Press ûPLAY to begin playing the MP3 files.

• The files will be played in the order they were entered.

CLEAR

RETURN

ZERO BACK

SKIP SEARCH

INPUT SELECT

REV FWD

PLAY

REC

STOP

TAPE

SPEED

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

VCR/DVD COMBINATION

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

5 Press

ËË

ËSTOP to stop programmed playback.

ËË

• To start programmed playback again, follow the steps below.

1 Press

ËË

ËSTOP to stop programmed playback.

ËË

2 Press PROG. 3 Select the file you programmed and press ENTER. 4 Press ûPLAY.

• Up to 24 chapters can be programmed.

DVD

Repeat Playback

DVD

Repeat playback

1 Press (REPEAT) while a disc is playing.

• The “

• Each time

• Depending on the disc type, the repeat function will vary.

Chapter Repeat

Title Repeat

A-B Repeat (See the next page for details.)

OFF

Track Repeat

Repeat all files in the disc

A-B Repeat (See the next page for details.)

” indicator appears on the DVD Front Panel.

(REPEAT) is pressed, the repeat function

changes as follows.

DVD

VIDEO

C D

VIDEO

C D

DVD

C D

CD-R/RW

OPERATE

VIDEO

C D

DV- NC70W

DV- NC70X

TIMER

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

REV FWD

REC

TAPE

SPEED

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

PLAY

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

DVD SETUP

DVD MENU

ZERO BACK

SKIP SEARCH

DV- NC70

EJECT

VCR MENU

OPEN/

SET

ENTER

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

OFF

CD-R/RW

(Only MP3 File Format)

Repeat one file

DVD

Repeat all files in the folder

OFF

2 Press ENTER to start repeat playback.

• Press

playback.

• Repeat playback is disabled on some discs.

• Repeat playback cannot be used during programmed playback.

(REPEAT) and select OFF when returning to regular

VCR/DVD COMBINATION

DVD

C D

A-B Repeat

VIDEO

C D

Repeat Playback

A-B repeat allows you to repeat specified section on the disc.

1 Press (REPEAT) three times while a disc is playing. 2 While you are playing a disc, press ENTER when you reach the

start of the section to be repeated.

3 While the disc is playing the same chapter/track, press ENTER

again when you reach the end of the section to be repeated.

• The A-B repeat begins from the point where you specified in

step 2.

• Press

to regular playback.

• To cancel A-B repeat, press

• A-B repeat can only be used within the same title/track.

(On some DVD discs, A-B repeat is restricted to the same chapter.) If the title/track finishes before specifying the ending location (B), the location where the title/track finishes will be set as the ending location (B).

• The A-B repeat function cannot be used during programmed playback.

• If the DVD Fr ont Panel display does not show the elapsed playback time

while a disc is playing, A-B repeat playback cannot be used for that disc.

• The A-B repeat function does not operate in scenes where different camera angles are recorded.

• The A-B repeat function cannot be used on VIDEO CDs with PBC mode playback.

• Repeat playback cannot be used during programmed playback.

DVD

(REPEAT) to turn off the “ ” indicator when returning

ËË

Ë STOP, TITLE or DVD MENU.

ËË

TIMER

OPERATE

ON/OFF

VCR/DVD

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

SCREEN

PROG/

REPEAT

SELECTOR

ANGLE

INPUT SELECT

REV FWD

PLAY

REC

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

TAPE

SPEED

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

VCR DVDAM/PM

PAUSE/STILL

SLOW

G-CODE

PROG

VCR/DVD COMBINATION

C D

Resume Function

DVD

C D

This function enables you to resume the playback from the location you specify.

1 Press ËSTOP at the desired point during playback.

• “RESUME” appears followed by “RESUME” on the screen.

• This product stores the location where you stopped.

DVD

RESUME

To CANCEL RESUME PLAY PRESS STOP

2 Press ûPLAY to restart play.

• Play resumes from a point slightly before the point where it was stopped.

• Press ûPLAY to resume disc play, if auto-playback starts from the beginning of the disc when you reload the same disc after removing it.

VIDEO

C D

OPERATE

DISPLAY

FUNCTION

CONTROL

TITLE

CLEAR

RETURN

TIMER

ON/OFF

SCREEN

PROG/

REPEAT

VCR/DVD

SELECTOR

ANGLE

DV- NC70W

DV- NC70

DV- NC70X

EJECT

VCR MENU

DVD SETUP

OPEN/

DVD MENU

SET

ENTER

ZERO BACK

SKIP SEARCH

G-CODE

PROG

• Resume information will not be cancelled even if the power is turned off.

• The continued playback described here may not be possible on some discs (such as discs that automatically start playing when the disc tray closes).

• The resume operation does not work in the following cases

– VIDEO CDs with PBC mode playback. – MP3 file playback.

This resume operation is cancelled in the following cases.

• If you press ËSTOP twice.

• If you press ËSTOP during auto-playback.

• When you open the disc tray.

• After enabling the Resume function.

VCR DVDAM/PM

INPUT SELECT

REV FWD

PLAY

REC

TAPE

SPEED

VCR/DVD COMBINATION

STOP

DPSS

SKIP

AUDIO

OUTPUT

VCR DVD

PAUSE/STILL

SLOW

Sharp DV-NC70W, DV-NC70 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual