SHARP ARPB2 Configuration Report and Test Page

AR-PB2
[6] Configuration Report and Test Page
1. Samples
2. Description of Each contents
This section defines the meaning of each item. These items are basically used in configuration pages, but some contents are not used depending on language.
A. Hardware Status
Machine Information
Value: 600 dpi Example: 600 dpi Default: 600 dpi Description: It is always 600 dpi.
b. Language
Value: (English | Deutsch (German) | Francais (French)
|Italiano (Italian) | Nederlands (Dutch) | Espanol
(Spanish) |Svenska (Swedish) Example: English Default: Depends on copier language Description: AR-PB2 includes seven language messages originally.
AR-PB2 decides the display language depending on the
language code sent from MAIN (MAIN sends the lan-
guage code based on its language ROM). This value
indicates the language that sent by MAIN to PRT.
6 – 1
AR-PB2
Hardware Specs
a. Base Memory
Value: 16 MB Example: 16 MB Default: 16 MB Description: It indicates base memory quantity of the printer board.
Basically, this is fixed at 16 MB and it cannot be changed.
b. Optional Memory
Value: (0|16|32|48|64) MB Example: 0MB Default: 0MB Description: It indicates the printer board’s optional memory quantity.
The customer (serviceman) could extend the memory by attaching 72pin-SIMM. 0MB means optional memory is not attached. 16MB or 32MB SIMM can be used to this purpose.
c. Total Memory
Value: (16|32|48|64|80) MB Example: 16MB Default: 16MB Description: It indicates the printer board’s total memory quantity. In
other words, it is summation of Base Memory and Op­tion Memory.
Version Information
a. PRT
Value: #.## Example: 2.00 Default: Depends on printer firmware version Description: This number should be same as the PRT-PRG ROM
version number seen on serviceman simulation 22-5.
b. BOOT
Value: #.## Example: 2.00 Default: Depends on printer firmware version
c. ICU
Value: #.## Example: 2.00 Default: Depends on printer firmware version Description: This number should be same as the ICU ROM version
number seen on serviceman simulation 22-5.
Installed Device
a. Duplex Module
Value: (Yes | No) Example: Yes Default: Depends on the Machine configuration Description: It indicates that duplex unit is attached or not.It depends
on hardware configuration.
b. Output Device
Value: (Standard 1 Tray | Standard 2 Trays | 3 Tray Finisher|2
Tray Finisher) Example: 3 Tray Finisher Default: Depends on the Machine configuration Description: It indicates attached output device.. It depends on
hardware configuration.
c. Paper Input Trays
Value: (2 trays | 3 trays | 4 trays) Example: 2 trays Default: Depends on the Machine configuration
Description: It indicates the number of standard input trays.It
d. Large Capacity Tray
Value: (Yes | No) Example: Installed Default: Depends on the Machine configuration Description: It indicates that large capacity paper input tray(Large
e. Interface Board
Value: (None | Ethernet | TokenRing) Example: Ethernet Default: Depends on the Machine configuration Description: It indicates the kind of installed network card option to
depends on hardware configuration.
Capacity Tray) is attached or not. It depends on hardware configuration.
the slot. 10Base-T/2 and 10/100Base-T are not iden­tified. Those two will be reported as Ethernet. TokenRing would not be supported for AR-PB1 (AR­PB2) for Japan domestic.
Available Paper Size
Appearance on
Configuration Page
Letter (81/2x11) Letter / Long Edge Feed
Letter (81/2x11R) Letter / Short Edge Feed
Legal (81/2x14) Legal / Short Edge Feed
Ledger (11x17) Ledger / Short Edge Feed
Executive (7 1/4x101/2) Executive / Short Edge Feed
Invoice (5 1/2x81/2) Invoice / Long Edge Feed
Foolscap (81/2x13) Foolscap / Short Edge Feed1
A4 A4 / Long Edge Feed
A4R A4 / Short Edge Feed
B5 B5 / Long Edge Feed
B5R B5 / Short Edge Feed
B4 B4 / Short Edge Feed A3 A3 / Short Edge Feed A5 A5 / Long Edge Feed A6 A6 / Short Edge Feed
Japanese Postcard Japanese Postcard / Short Edge Feed
(Unknown) Other size (EXTRA) (No Paper) No paper available on this tray.
(No Tray) There is a problem with this tray.
(Tray Open)
a. Tray 1 / Tray 2 / Tray 3 / Tray 4
Value: [Appropriate Paper Size] Example: Letter (81/2x11) Default: Depends on paper tray configuration. Description: It indicates paper size configuration of Tray 1 /2 / 3 / 4 /
5. It depends on hardware configuration, not software condition. (Unknown) means paper size cannot be identified. (Tray configuration is "EXTRA".) This line is not printed for unavailable tray.
b. Large Capacity Tray
Value: [Appropriate Paper Size] Example: Letter (81/2x11)
This tray is opened (except Bypass-Tray)
Description
or Tray is lifting up.
6 – 2
AR-PB2
Default: Depends on paper tray configuration. Description: It indicates paper size configuration of Large Capacity
Tray. It depends on hardware configuration, not software condition. When tray is opened, nothing is printed at here. This line is not printed when Large Capacity Tray is not attached.
c. Bypass-Tray
Value: [Appropriate Paper Size] Example: Letter (81/2x11) Default: Depends on the paper size set on Bypass Tray. Description: It indicates paper size of set on Bypass Tray. It depends
on detection of Bypass Tray paper size. (Unknown) means paper size cannot be detected.
B. Software Information
PostScript Emulation
a. Job Time-out
Value: # (variable length digit) Example: 0 Default: 0 Description: This value indicates PostScript Job Time-out length
(seconds). If this time will pass from receiving the job then PostScript interpreter will give up to print the job and cancel.
b. Manual Feed Time-out
Value: # (variable length digit) Example: 0 Default: 0 Description: This value indicates PostScript Manual Feed Time-out
length (seconds). If the print data break off during print­ing and this time will pass, then PostScript interpreter will cancel the print job. 0 means never time out.
c. Wait Time-out
Value: # (variable length digit) Example: 300 Default: 300 Description: This value indicates PostScript Wait Time-out length
(seconds). If the print data break off during printing and this time will pass, then PostScript interpreter will cancel the print job. 0 means never time out.
PCL5e Emulation
This section tells PCL5e information. This section would not appear on AR-PB1 (Siam) for Japan domestic.
a. Font Source
Value: (Resident | Download) Example: Resident Default: Resident Description: Current font source to print characters in PCL mode.
b. Font Number
Value: 0 to 45 Example: 0 Default: 0 Description: This is the current default font number used for plain
PCL job stream.
c. Font
Value: (PCL font name) Example: Courier Default: Courier Description: Current default font for PCL printing.
d. Pitch Size
Value: # (variable length digit) Example: 0.44 to 99.99 in 0.01 steps Default: 10.00 Description: This is the current default pitch size for plain PCL job
stream.
e. Point Size
Value: # (variable length digit) Example: 4.00 to 999.75 in 0.25 steps Default: 12.00 Description: This is the current default point size for plain PCL job
stream.
f. Symbol Set
Value: (PCL symbol set name) Example: Roman-8 Default: Roman-8 Description: This is the current default symbol set for plain PCL job
stream.
Network Information
a. NIC Serial Number
Value: ###### Example: 123456 Default: Depends on NIC. Description: It indicates the NIC’s serial number. This value is written
in NIC’s ROM (or flush ROM).
b. NIC Firmware Version
Value: ###### Example: 123456 Default: Depends on NIC. Description: It indicates the NIC’s serial number. This value is written
in NIC’s ROM (or flush ROM).
c. NetWare Print Server Name
Value: [User Definable] Example: SHARP_990792 Default: SHARP_[NIC card serial number] Description: This value must reflect the printer name for IPX/SPX
(NetWare).
6 – 3
Loading...