SHARP ARM162, ARM207, ARM165 Service Manual

CODE : 00ZARM207/A1E

AR-M162 AR-M165

AR-M207

With the RSPF installed

[ 1 ] GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[ 3 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . 4 - 1

DIGITAL COPIER

AR-M207 AR-M165

MODEL AR-M162

CONTENTS

[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 5 - 1

[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[ 7 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

[ 8 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 -1

[ 9 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

[10] DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . 10 - 1

[11] KEY OPERATOR PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1

[12] FRASH ROM VERSION UP PROCEDURE . . . . . . . . . . . . . . 12 - 1

[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

Parts marked with “ “ are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

CONTENTS

[1] GENERAL

1. Cautions on using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

2. Installation requirements . . . . . . . . . . . . . . . . . . . . . . . .1-1

3. Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

[2] SPECIFICATIONS

1. Basic specificatio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

[3] CONSUMABLE PA RTS

1. Supply system table. . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

2. Environmental conditions. . . . . . . . . . . . . . . . . . . . . . . .3-2

3. Production number identification . . . . . . . . . . . . . . . . . .3-2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

2. Internal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

3. Operation Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

4. Display(base screen) . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

5. Motor, solenoid, clutch. . . . . . . . . . . . . . . . . . . . . . . . . .4-6

6. Sensor, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

7. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

8. Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

[5] UNPACKING AND INSTALLATION

1. Installing conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

2. Removal of protective material and fixing screw . . . . . .5-1

3. Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

4. Removal and storage of fixing screw. . . . . . . . . . . . . . .5-2

5. Changing the paper size setting of a trey. . . . . . . . . . . .5-3

[6] ADJUSTMENTS

1. Adjustment item list . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

2. Copier adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

[7] SIMULATIONS

1. Entering the simulation mode. . . . . . . . . . . . . . . . . . . . .7-1

2. Canceling the simulat i o n mode . . . . . . . . . . . . . . . . . . .7-1

3. List of simulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

4. Contents of simulati ons . . . . . . . . . . . . . . . . . . . . . . . . .7-3

[8] TROUBLE CODE LIST

1. Trouble code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

2. Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . . . 8-2

[9] MAINTENANCE

1. Maintenance table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

2. Maintenance display system. . . . . . . . . . . . . . . . . . . . . 9-2

3. Note for replacement of consumable parts. . . . . . . . . . 9-2

[10] DISASSEMBLY AND ASSEMBLY

1. High voltage section/Duplex transport section . . . . . . . 10-1

2. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

3. Fusing section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

4. Paper exit section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6

5. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9

6. Optical frame unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9

7. LSU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9

8. Tray paper feed section/Paper transport section. . . . . . 10-10

9. Manual multi paper feed section. . . . . . . . . . . . . . . . . . 10-11

10. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13

11. Deve lo p i n g sec tio n . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14

12. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-15

13. Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16

[11] KEY OPERATOR PROGRAM

1. Custom setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

2. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

[12] FLASH ROM VERSION UP PROCEDURE

1. Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

2. Driver Installation procedure. . . . . . . . . . . . . . . . . . . . . 12-1

3. Download procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3

4. V ersion confirming procedure. . . . . . . . . . . . . . . . . . . . 12-5

[13] ELECTRICAL SECTION

1. Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

2. Circuit descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2

3. Actual wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8

[1] GENERAL

1. Cautions on using

A. Warning

•The fusing area is hot. Exercise care in this area when removing misfed paper.

Fusing unit

•Do not look directly at the light source. Doing so may damage your eyes .

2. Installation requirements

Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.

1. The machine should be installed near an accessible power outlet for easy connection.

2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.

•For the power supply requirements, see the name plate on the back of

the main unit.

Note: Connect the machine to a power outlet which is not used for other

electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

3. Do not install your machine in areas that are:

•damp, humid, or very dusty

•exposed to direct sunlight

•poorly ventilated

• su bject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

4. Be sure to allow the required space around the machine for servicing and proper ventilation.

8" (20 cm)

B. Cautions

•Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on.

•Place the machine on a firm, level surface.

• When the machine is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

• When moving the machine, be sure to turn the power switch off and remove the power cord from the outlet.

•Do not cover the machine with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the machine.

•Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine.

•Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from printing by national law . Other items may be prohibited by local law.

Money, Stamps, Bonds, Stocks Bank drafts, Checks, Passports, Driver’s licenses

•Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints.

•Store spare toner car tridges in a cool dry plac e without removing from the package before use.

• If they are exposed to direct sunlight or excessive heat, poor copies may result.

(20 cm)

AR-M207 M165 M162 GENERAL 1-1

3. Configuration

A. System Configurations

Job separator

(AR-TR4)

RSPF(AR-RP6N) SPF(AR-SP6N)

AR-M207

With the RSPF installed

Network Box

(AR-NB3)

AR-M165 AR-M162

2 X 250 sheet paper

feed unit

(AR-D25)

MODEL OPTION AR-RP6N REVERSING SINGLE PASS FEEDER OPT OPT NO AR-SP6N SINGLE PASS FEEDER OPT OPT OPT AR-VR5 DOCUMENT COVER OPT STD STD AR-D24 250-SHEET PAPER FEED UNIT OPT OPT OPT AR-D25 2 x 250-SHEET PAPE R FEED UNI T OPT OPT OPT AR-TR4 JOB SEPARATOR TRAY KIT OPT OPT OPT AR-EB9 DUAL FUNCTION BOARD STD*1 STD STD*1 *1

AR-NB3 NETWORK PRINTING / SCANNING

EXPANSION K I T AR-FX11 FACSIMILE EXPANSION KIT OPT OPT OPT AR-SM5 EXPANSION MEMORY OPT OPT OPT AR-MM9 FAX EXPANSION MEMORY OPT OPT OPT AR-PF1 BARCODE-FON T KI T OPT OPT OPT The AR-NB3 is

AR-PK1N PS3 KIT OPT OPT OPT The AR-NB3 is

AR-PF2 FLASH MEMORY KIT OPT OPT OPT The AR-NB3 is

AR-M207 AR-M165 AR-M162 Remark

OPT OPT OPT

250 sheet paper

feed unit

(AR-D24)

Option for USA,CANADA.

required

AR-M207 M165 M162 GENERAL 1-2

[2] SPECIFICATIONS

1. Basic Specification

A. Base Engine

(1) Type

AR-M207, AR-M162 / M165 Desk-top

(2) Engine speed

Paper size AR-M207 AR-M162 / M165 A4/8.5" x 11" 20ppm 16ppm A4R/8.5" x 11"R 14/15ppm 12ppm A5/5.5" x 8.5" 20ppm 16ppm B5/16K 20ppm 16ppm B5R/16KR 16/15ppm 14ppm

8.5" x 13" 12ppm 11ppm B4/8.5" x 14 12ppm 10ppm A3/11" x 17"/8K 11/10/11ppm 9/ 9/10ppm

(3) Print performance

AR-M207 AR-M162 / M165 GDI Print* 12ppm 12ppm SPLC Print 20ppm(ROPM) 16ppm(ROPM)

* GDI print measurement c onditions: Host PC/CPU = 500 700MHz o r

above, Windows 98SE, Data = TestChart-B1.doc, USB1.1, when supporting A4/Letter. Measurement method: With setting to 11, from completion of the first paper exit to completion of the 11th paper exit

(4) Copy speed(cpm)

AR-M207 AR-M162 / M165

Normal A4/8.5"x11" 20 20 20 16 16 16 A4R/

8.5"x11"R A5/5.5"x8.5" 20 20 20 16 16 16 B5/16K 20 20 20 16 16 16 B5R/16KR 16/15 16/15 16/15 14 14 14

8.5x13" 12 12 12 10 10 10 B4/8.5"x14 12 12 12 10 10 10 A3/11"x17"/8K11/10/1111/10/1111/10/119/9/10 9/9/10 9/9/10

14/15 14/15 14/15 12 12 12

Reducti on

Enlargement

Normal

Reduction

Enlargement

(6) Job Speed

AR-M207 AR-M162 / M165 S S 20 Sheets/min(100%) 16 Sheets/min(100%) S D 9 Sheets/min(45%) D D 8 Sheets/min(40%) -

* S S(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document, 5

copies

* S D(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document, 5

copies

* D D(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document(20

surfaces), 5 copies

(7) Continuous copying

Max. number of multi copy

1-999copies(Can be changed to 1-99 in key operator programs)

(8) Engine composition

Photoconductor type

Photoconductor drum dia.

Process cleaning Blade Copy lamp Cold cathode fluorescent lamp(CCFL) Developing system Dry 2-component magnetic brush development Charging system Saw teeth charging Transfer system (+)DC scorotro n Separation system (-)DC scorotron Fusing system Heat roller Process speed 88mm/s

OPC(Organic Photo Conductor)

30mm

(9) Engine resolution

Resolution Reading: 600 x 300dpi1(600 x 600dpi selectable)

Gradation Reading: 256 gradation, Writing: 2 gradations

Writing: 600x600dpi

(10)Scanner section

Scanner(Document table)

(5) First copy time

First copy time 7.2sec or less

* Measurement conditions: When feeding paper of A4/8.5" x 11" from the

main unit tray, polygon rotation state

Main unit first stage

Main unit second stage

Option paper feed first stage

Option paper feed second stage

Manual tray 7.5sec or less

First copy time from the document feed unit

SPF 12sec or less RSPF 12s ec or less

7.2sec or less

8.5sec or less

9.5sec or less

10.5sec or less

AR-M207 M165 M162 SPECIFICATIONS 2-1

(11) Document table

Max. Document size

Scan area 297 x 431mm Document

reference position Detection(Platen) Available Detection size Automatic detection(supported by each unit for

OR guide display Left back corner

AB and inch can be switched to each other by Sim.

A3/11"x17"

Left back corner reference

inch/AB) AB system: A3, B4, A4, A4R, A5, Inch system: 11" x 17", 8.5" x 14",

(Print display) Left side document

guide

Left side document guide

Back side document guide(Bookmark)

8.5" x 11", 8.5" x 11"R Document reference

position “ ” (From the back)

[Postal card] · [A6 ] · [B 6 ] · [5-1/2] · [A5 ] · [B5 ] · [A4/A5 ] · [8-1/2] · [B4/B5 ] · [11] · [A3/A 4 ]

(From the left) [5-1/2] · [A5] · [B5] · [A4/ A5 ] · [8-1/2] · [B5 ] · [11]

· [A4 ] · [13] · [14] · [B4 ] · [A3 ] · [17]

B5(Vertical), A4(Vertical), bookmark at 8" - 1/2" position(From the left)

(12) SPF/RSPF

Type SPF/RSPF Single/Duple x automatic

document feeder unit

Scan speed Single surface When copying: 20-sheet

Document reference position

Document size AB system: A3-A5

Document weight 56 - 90g/m²(15 - 24lbs)

Document load capacity

Inhibited kinds of documents

Detection Avaiable Detection size * Automatic detection(A kind of detection unit is used

Document tray guide display

Center

Inch system: 11" x17" - 5.5" x 8.5"

when duplex: 56 - 90g/m²(15 - 24lbs) 40 sheets(30 sheets of 90g/m² loadable)(30 sheets

for B4/8.5" x 13" or above)40 sheets of 4mm thickness or below loadable

Transparency film, Perforated sheets, photo, catalogue

by switching the software destination.) AB system: A3,B4,A4,A4R,B5,B5R,A5 Inch system: 11" x 17", 8.5" x 14", 8.5" x

Tray center(Marked)

Document guide(Marked)

model/20 sheets/min 16-sheet model/16 sheets/min When FA X: 23 sheets/min

11", 8.5" x 11"R, 5.5" x 8.5" Document insertion direction

“ ”document face-up set command

(From the center) A3/A4, 11", B4/B5, 8.5", A4R/A5, B5R, A5R, 5.5"

(13) Operation panel

a. Display device

Type LCD display with backlight System FSTN Display dot

number LCD drive display

area LCD brightness

adjustment Type 7 segment LED(x 3)

b. Key

Mode selection area

Basic input section Start key/LED

LCD display section

Panel language support

c. Characters used in LCD

Kind ROM font Dot 6(W)x 12(H)

119 x 73 dots

78.867 x 41.653 mm

Available

Copy mode key(mode LED) Print mode key(mode LED/ONLINE LED/DATA LED) Scanner mode key(mode LED) Fax mode key(mode LED/LINE LED/DATA LED)

Numeric keys * AUDIT CLEAR key # Read End key Clear/Stop key Interru p t key All Clear key

Exposure key(Color mode/Program) Paper ke y(Resolution/Program) Zoom key(Address) Auto% key(Format/Broadcast) Duplex key(Duplex scan) Sort(Documen t size) Special function key Fax status key Arrows key OK key Back key LINE STATUS indicator (when the fax option is installed)

English(Factory setting) For the languages other than English, the key sheet is packed together with the machine or manual kit. Attach it when installing.

(14) Controller board

CPU H8S2321(16bit 1-chip microprocessor,

Memory 16MB(Single surface model)

Interface

IEEE1284 Parallel 1 port USB1.1 1 port USB2.0 1 port(Standard/option area) Ethernet 1 port(Network box)

19.6608MHz)

32MB(Duplex surface model)

(15) Paper feed section

Type 4-stage paper feed tray + multi manual paper feed Paper feed system Front loading, paper feed from the top

AR-M207 M165 M162 SPECIFICATIONS 2-2

Main unit tray

Size to be fed A3, B4, A4, A4R, B5, B5R, A5(No.1 tray only)

16K, 16KR, 8K, 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11",

8.5" x 11"R, 5.5" x 8.5"(No. 1 tray only) Paper size setting Us er setting Paper size setting A3, B4, A4, A4R, B5, B5R, A5,

11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11",

8.5" x 11"R, 5.5" x 8.5"

(For A5/5.5" x 8.5", however, No. 1 cassette only)

Paper size setting when shipping

Kind and weight of applicable paper

Paper feed capacity

Paper type Standard paper, Recyc led paper Remaining

quantity detection

AB system: A4 Inch system: 8.5" x 11"

Standard paper 56 - 90g/m²

Standard paper 250 sheets(64g/m²)

Only empty detection available

(16) Manual paper feed section

Manual paper feed form

Paper size A3 - A6,

Manual paper feed guide display

Kind and weight of applicable paper

Paper capacity Standard

Paper kind AB system: Standard paper/Recycled paper/

Paper size detection

Paper empty detection

Foldable manual paper feed tray

11" x 17" - 8.5" x 11" A3/A4, B4/B5, A4R/A5, B5R, A5R, B6R, A6R

Standard paper Thick paper(56 - 200g/m²) Recycled paper, Envelope, Transparency film, Labels

100 Sheets

paper

Envelope AB system: 10 Sheets

Other Single paper feed(Transparency film,

Transparency film/Labels/Postal card/Envelope/ Thick paper(-200g/m²) Inch system: Standard paper/Recycled paper/ Transparency film/Labels/Postal card/Envelope/ Thick paper(-200g/m²)

None

Available

(Standard paper: 56 - 80g/m²)(Multi paper feed: 56 -128g/m²)

Inch system: 5 Sheets

Labels, Postal card)

(17) Duplex

Standard 20-sheet m odel: Standard provision

Type Switchback system Paper size A3, B4, A4, A4R, B5, B5R, A5,

Kind and weight of applicable paper

16-sheet model: Not available

11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11",

8.5" x 11"R

Standard paper: 56 - 90 g/m²/15 - 24lbs Bond

(18) Paper exit section

Paper exit position/system

Paper exit section capacity

Paper exit paper size/kind

Paper exit paper full detection

Face do wn

250 sheets

All feedable paper types and sizes

Upper stage: Available(Detected when the job separator is installed) Lower stage: None *250 sheets of counted and detected.

(19) Exposure(Print density)

Density mode Auto/Text/Photo NO. Of manual

adjustment Toner save mode Available(Default OFF with the service simulation)

5 steps(Text/Photo)

(20) Void width

Void area Lead edge: 1 - 4mm, rear edge: 4mm or less,

both sides: 6mm

Image loss 4mm or less

* For void area/image loss, normal/single copy. * For the first sheet of manual paper feed, the rear edge void is disable.

(21) Warm-up

Warm-up time 45sec or less Pre heat Available Jam recovery time 45sec or less

Left for 60 sec after door open. Standard condition, polygon stop

(22) Copy magnification ratio

Fixed magnification ratio

Zooming 25-400%(SPF/RSPF: 50-200%) Independent

zooming

AB system: 25, 50, 70, 81, 86, 100, 115, 122, 141, 200, 400% Inch system: 25, 50, 64, 77, 95, 100, 121, 129, 141, 200, 400%

Vertical/horizontal: 25-400% (SPF/RSPF: 50-200%)

(23) Power source

Voltage 100V, 110V, 120V, 127V, 230V(200V), 240V Frequency 50/60Hz Power switch One power source

(24) Power consumption

Max. Power consumption

Power consumption in operation

Power consumption when standby

* Must conform to energy saving laws, international standards, and

company regulations.

1200W

550W

10W

AR-M207 M165 M162 SPECIFICATIONS 2-3

(25) Environment support

Support program International Energy-Star

Nordic swan Canadian environment selection program Blue angel eco-label Green purchase network Green purchase law Energy-saving law Green products

(26) Noises

Noise level Must conform to SS, blue angel, Nordic swan.

(27) Ozone & dust

Regulated value Ozone: 0.02mg/m³ or less

Dust: 0.075mg/m³ or less Styrene: 0.07mg/m³ or less

(28) External dimensions

1-stage cassette model(floor surface - glass surface)

1-stage cassette model(floor surface - OC)

1-stage cassette model(floor surface - SPF)

2-stage cassette model(floor surface - glass surface)

2-stage cassette model(floor surface - OC)

2-stage cassette model(floor surface - SPF)

3-stage cassette model(floor surface - glass surface)

3-stage cassette model(floor surface - OC)

3-stage cassette model(floor surface - SPF)

4-stage cassette model(floor surface - glass surface)

4-stage cassette model(floor surface - OC)

4-stage cassette model(floor surface - SPF)

590(W) x 595(D) x 435(H)

590(W) x 595(D) x 469(H)

590(W) x 595(D) x 568(H)

590(W) x 595(D) x 520(H)

590(W) x 595(D) x 554(H)

590(W) x 595(D) x 652(H)

590(W) x 595(D) x 605(H)

590(W) x 595(D) x 640(H)

590(W) x 595(D) x 738(H)

590(W) x 595(D) x 690(H)

590(W) x 595(D) x 725(H)

590(W) x 595(D) x 823(H)

(29) Occupying area

Main unit only (excluding the handle)

Main unit(Multi manual feed open) 880(W ) x 595(D)

590(W) x 595(D)

(30) Weight

20-sheet model (Electronic sort : Standard)

20-sheet model (Electronic sort : Option)

16-sheet model (Electronic sort/Duplex)

16-sheet model (Electronic sort : Standard)

16-sheet model (Electronic sort : Option)

34.2 (Kg)

33.8 (Kg)

30.6 (Kg)

30.0 (Kg)

29.7 (Kg)

(31) Printer basics

GDI/SPLC Print

Print speed GDI: 12PPM(GDI Print, USB2.0(Full speed), A4/

First Print 7.2sec or less Resolution 600dpi Duplex print Available Paper feed system Paper feed tray and multi paper feed Shifter Installed to the main unit paper exit section.

Supported OS Windows95/98/Me/NT4.0(Workstation SP5 or

Emulation GDI

Interface IEEE1284(ECP, Compatible)

PnP Support Windows 95/98/Me/2000/XP Software Status Window ROPM When the Dual function board (AR-EB9) is

WHQL Yes(XP/2000) after a few month later from first lot.

Letter) Measurement conditions: Host PC/CPU: 500 700MHz, RAM: 256MB or above, Windows98SE Data Testchart-B1, dot SPLC: According to the main machine speed.

Shit amount: 1 inch(25.4mm)journalizing according to every print j o b.

later)/2000(Professional)/XP(Home/Professional)

SPLC(JBIG-GDI): When the Dual function board (AR-EB9) is installed (Standard or option).

USB1.1 USB2.0(When the Dual function board (AR-EB9) is installed (Standard or option).

installed (Standard or option).

(32) Scanner basics

Type Flat bed color scanner Scan system Document table/document feed unit Light source Whit e CCFL Resolution Basic 600 x 600 dpi

Document Sheet/Book Effective scan

range Scan speed 2.88msec /Line(C olor) Input data 1bit or 12bit Output data 1bit or 8bit Scan color Black and white binary/Gray scale/Full color Protocol TWAIN/WIA(XP Only)/STI Interface USB1.1

Scanner utility Sharpdesk Drop-out color Provided Scanner button Destination selection by LCD Duplex scan Available Supported OS Windows98/Me/2000(Professional)/XP(Home/

Void area Lead edge/rear edge: 2.5mm

WHQL Yes(XP/2000) after a few month later from first lot.

Set range: 50 - 9600dpi

OC/SPF/RSPF: about 297(length)x 431(width)mm

USB2.0

Professional)

Side Left/right: 3.0mm

AR-M207 M165 M162 SPECIFICATIONS 2-4

(33) Network box basics

Standard memory 64MB Expansion

memory Interface RJ45, USB port(for connection with the main unit) LED Power LED, 10/100BASE-Tx mode LED,

Switch Status Switch Supported OS

Setting software Internet Explorer 5.5 or later, Netscape Navigator 6

Expansion option PS expansion kit(AR-PK1N)

Network protocol TCP/ I P, IPX/SPX(NetWare), NetBEUI,

Emulation PCL/PS(PS is cancelled by the soft key.)

E-RIC Canceled by the soft key.

1DIMM 1 slot 144pin 128/256MB SO-DIMM

LAN status LED, USB status LED

Windows 95/98/Me/NT4.0(Workstation SP5 or later)/2000 professional/XP Home Edition/XP Professional Edition/Windows Sever 2003 Mac OS 8.6 - 9.2.2, 10.1.5, 10.2 - 10.2.8 (excluding

10.2.2), 10.3 - 10.3.4 (when PS option)

or later

Barcode font kit(AR-PF1) Flash ROM kit(AR-PF2) Sharpdesk(Shar p desk license kit AR-U seri es)

Ether Talk(Apple Talk)

ESC/P Font Kanji: Mincho, Gothic(Bitmap) ANK: Roman, Sans Serif(Bitmap)

B. Peripheral devices basic specifications

(1) Single pass feeder(SPF)

Document set Face up Document

reference position Document

transport system Document feed

direction Document size AB system : A3 - A5

Document weight 56 - 90g/m²(15 - 24lbs) Document set

quantity

External dimensions

Weight 5.0kg Power Supplied from the machine(Power consumption:

Document size detection

Detection size AB system A3, B4, A4, A4R, B5, B5R, A5

Guide display (From the center)

Documents out of specifications

Multi copy S-S, S-D(Duplex model) Document mixture Not available Random paper

feed Document

reversion Display

section(LED)

Right side center

Sheet through type

Document feed from the top

Inch system: 11" x 17" - 5.5" x 8.5"

40 sheets(40 sheets of 4mm thickness or less can be loaded.) (30 sheets of 90g/m² can be loaded. 30 sheets for B4 or 8.5" x 13" or above.)

583 mm(W) x 435 mm(D) x 133 mm(H)

21W) On the document feed trey

Inch system 11" x 17", 8.5" x 14", 8.5" x 11",

8.5" x 11"R, 5.5" x 8.5"

A3/A4, 11", B4/B5, 8.5", A4R/A5, B5R, A5R, 5.5" Transparency film/Perforated document, photo,

catalogue

Not availabl e

None

Reliability(MCBJ/ MCBF)

Document replacement speed(Standard copy)

Item included Installation manual Case color Frosty white Installation Must be installed easily.

Conforms to the main unit.

S-S 16-sheet model: 100%

20-sheet model: 100% S-D 20- sheet model: 45%(9 sheets/min) D-D -

(2) Reversing single pass feeder(RSPF)

Document set Face up Document

reference position Document

transport system Document feed

direction Document size AB system: A3 - A5

Document weight 56 - 90g/m²(15 - 24lbs)

Document set quantity

External dimensions

Weight 5.4kg Power Supplied from the machine(Power consumption:

Document size detection

Detection size AB system A3, B4, A4, A4R, B5, B5R, A5

Guide display (From the center)

Documents out of specifications

Multi copy S-S, S-D, D-D, D-S(Duplex model) Document mixture Not available Random paper

feed Document

reversion Display

section(LED) Reliability(MCBJ/

MCBF) Document

replacement speed(Standard copy)

Item included Installation manual Case color Frosty white Installation Must be installed easily

Right side center

Sheet through type

Document feed from the top

Inch system: 11" x 17" - 5.5"x8.5"

Duplex: 56 - 90g/m²(15 - 24lbs) 40 sheets(40 sheets of 4mm thickness or less can

be loaded.) (30 sheets of 90g/m² can be loaded. 30 sheets for B4 or 8.5" x 13" or above.)

583 mm(W) x 435 mm(D) x 133 mm(H)

26.4W) On the document feed trey

Inch system 11" x 17", 8.5" x 14", 8.5" x 11",

8.5" x 11"R, 5.5" x 8.5"

A3/A4, 11", B4/B5, 8.5", A4R/A5, B5R, A5R, 5.5" Transparency film, Perforated document, photo,

catalogue

Not availab le

Available(Not availab le for 5.5" x 8.5" and

5.5" x 8.5"R) None

Conforms to the main unit

S-S 16-sheet model: 100%

20-sheet model: 100% S-D 20- sheet model: 45%(9 sheets/min) D-D 20-sheet model: 40%(8 sheets/min)

AR-M207 M165 M162 SPECIFICATIONS 2-5

(3) 1-stage paper feed unit

Paper feed capacity Paper size detection Paper empty detection Paper size A3, B4, A4, A4R, B5, B5R, 11" x 17", 8.5" x 14",

Paper weight 56 - 90g/m²(15 - 24lbs) Factory setting size Size selection A3, B4, A4, A4R, B5, B5R,11" x 17", 8.5" x 14",

Cassette installation/ removal Power Supplied from the machine(Power consumption:

External dimensions Weight 5.0Kg Reliability(MCBJ/ MCBF) Item included Installation manual, Paper size label Case color Frosty white

250 Sheets

Not available(The paper size can be set with the function menu.) Available

8.5" x 13", 8.5" x 11", 8.5" x 11"R, 16K, 16KR, 8K

AB system: A4 Inch system: 8.5" x 11"

8.5" x 13", 8.5" x 11", 8.5" x 11"R Can be made by the user

5.6W) 590 mm(W) x 471 mm(D) x 88mm(H)

Conforms to the main unit

(4) 2-stage paper feed unit

Paper feed capacity Paper size detection Paper empty detection Paper size A3, B4, A4, A4R, B5, B5R, 11" x 17", 8.5" x 14",

Paper weight 56 - 90g/m²(15 - 24lbs) Factory setting size Size selection A3, B4, A4, A4R, B5, B5R

Cassette installation/ removal Power Supplied from the machine(Power consumption:

External dimensions Weight 10.0Kg Reliability(MCBJ/ MCBF) Item included Installation manual, Paper size label Case color Frosty white

250 Sheets x 2

Not available(The paper size can be set with the function menu.) Available

8.5" x 13", 8.5" x 11", 8.5" x 11"R, 16K, 16KR, 8K

AB system: A4 Inch system: 8.5" x 11"

11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11",

8.5" x 11"R Can be made by the user

8.4W) 590 mm(W) x 471 mm(D) x 174 mm(H)

Conforms to the main unit

(5) Dual function board

Expansion function

Electronic sort compress function Memory fo r electronic sort Electronic sort scan quantity Memory expansion

Item included Installation manual,

Electronic sort function, 2In1/4In1, Rotation copy, Edge erase/Center erase, Margin shift, Card shot USB2.0(High-speed support),SPLC print(JBIGGDI), ROPM function JBIG

16MB

A4 standard document(Test chart B)100 sheets

DIMM Memory slot x 1 Max. 256MB x 1slot + 16MB(Max 272MB in total) (Externally described as max. 256MB x 1)

(6) Original cover(OC)

Function Up/down open/close mechanism Item included Installation manual

(7) 256MB expansion memory

Memory 256MB Item included Installation manual

(8) Job separator

Installation conditions Bin number 1 bin Distribution system Paper size Conforms to the main unit paper feed paper. Paper weight Conforms to the main unit paper feed paper. Paper exit section capacity Paper exit job Upper stage: FAX output or printer output

Paper exit full detection Power None Item included Installation manual Case color Frosty white Installation Must be installed easily

Install when the printer or the FA X is expanded. Perf orms paper exit for every job

Controlled by the main unit.

Upper stage: 100 Sheets Lower stage: 150 Sheets

Lower stage: Copy output or printer output Upper stage: Available Lower stage: YES (Full detection by the counter)

(9) Network box

Function Supports the network printer(PCL/PS)and the

Power Supplied from the machine

External dimensions Item included USB2. 0code x 1

network scanner.

(Power consumption: 5.5W) 248 mm(W) x 127 mm(D) x 59 mm(H)

Software CD(Driver/Network setting/application) Installation manual

(10) Facsimile expansion kit

Function FAX expansion option Item included One-touch dial key, destination label, installation

manual

(11) Barcode font kit

Same as the AR-PF1.

(12) Flash memory kit

Same as the AR-PF2.

(13) PS3 expansion kit

Same as the AR-PK1N.

(14) Facsimile expansion memory

Same as the AR-MM9.

AR-M207 M165 M162 SPECIFICATIONS 2-6

C. Various functions specifications

(1) Copy function specification

Function/ Special function

Automatic paper selection

Automatic magnification ration selection

Auto tray switching

Memory copy Yes Rotation copy Yes (When electronic sort) Electronic sort Yes (Standard or option) Rotation sort No X Y zoom Yes Dual page copy Yes (Enlargement invalid/SPF

Sort function Yes (Standard or option)

Margin shift Yes (When electronic sort)

Edge erase Yes (When electronic sort)

Center erase Yes (When electronic sort)

Black/white reverse

2in1/4in1 Yes (When electronic sort) Sorter Yes (Offset function) Card shot Yes (When electronic sort) Preheating Yes (Set by the key operator

Auto shut-off Yes (Set by the key operator

Total counter Yes Duplex Yes (Standard provision for the

Toner save Yes (Set according to the

Department management

Yes

invalid(Patent rotation)

100 sheets of A4 standard document (Test Chart B)are sorted.

Default AB system: 10mm(5, 10, 15, 20mm) Inch system: 1/2 Inch(1/4, 1/2, 3/4, 1 Inch)

Default AB system: 10mm(5, 10, 15, 20mm)Inch system: 1/2 Inch(1/4, 1/2, 3/4, 1 Inch)

Default AB system: 10mm(5, 10, 15, 20mm) Inch system: 1/2 Inch(1/4, 1/2, 3/4, 1 Inch)

program.)

model of 20-sheet model only)

destination) (No setting. * Default OFF with the service simulation.)

Yes (Copy/printer/scanner: 50 Dept, Fax 50 dept)

(2) Printer function specification

a. GDI/SPLC Printer <Summary>

Platform IBM PC/AT(Include compatible machine) Supported OS IEEE1284 Windows95/98/Me/

USB1.1 Windows98/Me/

USB2.0 Windows2000(Professional)/

Emulation GDI/JBIG GDI Memory Environments for full operations of the above OS

Only the summary is described on this item.

Function Content

Main Copies 1-999 Makes prints of the set

Collate Collate

Document Style

N-up *1 2/4 The set pages are printed

N-up Order Z N-up Border Yes/No Border lines are printed

Duplex 1-sided

Paper Paper Size A3/B4/A4/B5/

Custom Paper Size *2

Fit to Page Yes/No The print size is changed

Image Orientation

Paper Selection

Rotate 180 Degree

NT4.0(Workstation SP5)/ 2000(Professional)/XP(Home/ Professional)

2000(Professional)/XP(Home/ Professional)

XP(Home/Professional)

number of copies.

Uncollate

1-sided 2-sided(Book) 2-sided(Tablet)

2-sided(Book) 2-sided(Tablet)

A5/A6/B6/ Ledger/Legal/ Foolscap/ Folio/Letter/ Invoice/ Executive/8K/ 16K/COM-10/ DL/C5/ Custom/Postal card

1 size Width: 100 - 297mm

Portrait Landscape

Auto Bypass Tray 1/2(3/4)

Yes/No Data are rotated 180

When this item is set to "Collate," prints of two or more copies are collated. When set to "Uncollated," two or more copies of each page are printed(uncollated).

Single face or double face print is made according to the setting. When set to duplex, the printing direction differs depending on book or tablet.

on one sheet.

between pages printed on one sheet.

Print is made in the set paper size. Even when the actual paper size differs from the set paper size, images are formed printed in the set paper size.

Length: 148-431.8mm

according to the set content.

Printing is made in the set direction.

Paper is fed from the set paper feed tray.

degrees and printed.

AR-M207 M165 M162 SPECIFICATIONS 2-7

Function Content

Paper Output Tray

Selection

Advanced Print Quality Draft

Image Adjustment

Brightness 0 - 100% The image brightness is

Contrast 0 - 100% T he image contrast is

Pured Black print

Watermarks

Watermarks None/TOP

User Setting Add/Update/

Position Center

Size 6 - 300 Angle ± 90 Grayscale 0 - 255 Edit Font Yes On First Page

only

Upper Tray Center Tray

Normal Photo

Yes/No Contrast and brightness of

Yes/No A docum ent ma de by a

SECRET/ CONFIDENTI AL/DRAFT/ ORIGINAL/ COPY

Delete

X: ± 50 Y : ± 50

Yes /No

When the job separator is installed, selection is made between the upper stage and the center stage of the paper exit tray.

Draft/Normal (only for Windows 9x, Me)

images are adjusted. For Windows NT4.0/2000/XP, enable only for the Photo mode of Print Quality.

adjusted by moving the scale from 0 to 100. The illustration image on the left upper corner of the display is changed.

CAD program is printed in black to provide clear print of color line images and texts.

(3) Scanner function Specification

a. PUSH Scan(USB)

Supported OS Win98/Me/2000/XP Hardware

environment

Selectable destination

b. PULL Scan(TWAIN)

Supported OS Win98/Me/2000/XP Hardware

environment

Duplex scan Yes Color mode Black and white(Simple binary)/Black and

Resolution Pull: 600 x 600dpi

Preview function Yes Zoom preview

function Rotation scan Yes (90 degrees/180 degrees/270 degrees) Brightness/

contrast adjustment

Gamma adjustment

Color matching None/Printer/CRT/LCD display/ICM Edge emphasis None/Normal/Strong/Blur Black/white

reverse Light source

selection Threshold value

setting Void area addition Available(Top/End edge = 2.5mm /Left/Right =

Set contents save Yes

(System)Must meet the operating conditions of each OS. (HDD)8MB or above: 100MB or above recommendable (Monitor)800 x 600 dots or above, 256 colors or more must be displayed. (Other)USB port(1.1 or 2.0)

SharpDesk/E-mail software/Fax software/OCR software/MS Word

USB TW AIN

(System)Must meet the operating conditions of each OS. (HDD)8MB or above: 100MB or above recommendable (Monitor)800 x 600 dots or above, 256 colors or more must be displayed.

(Other)USB port

white(Error diffusion)/Gray scale/Full color

Emulation: 50-9600dpi Custom: 50-9600dpi

Yes

Auto/Manual(-100 - +100)

Yes

Yes (Red/Green/Blue/White)

Auto/Manual(1 - 254)

3.0mm)

c. Network Push scan(When the network box is installed)

Selectable destination

Destination selection method

AR-M207 M165 M162 SPECIFICATIONS 2-8

Scan to E-mail/FTP/Desktop

Address book LDAP retrieval/selection Ad-Hoc(10-key input)

[3] CONSUMABLE PARTS

1. Supply system table

A. USA / CANADA

NO Name Content Life Product name Remark

1 Toner cartridge(Black)

2 Developer Developer

3 Dru m kit Drum

B. Europe / Australia / New Zealand

NO Name Content Life Product name Remark

1 Toner cartridge(Black)

2 Developer Developer

3 Dru m kit Drum

Toner (Toner: Net Weight 537g) Vinyl bag

(Developer : Net Weight 400g)

Drum fixing plate

Toner (Toner: Net Weight 537g) Vinyl bag

(Developer : Net Weight 400g)

Drum fixing plate

x10

160K AR-202MT Life setting by A4 6% document

x10 x10 500K AR-202MD

x1x150K AR-202DR

x10

160K AR-202LT Life setting by A4 6% document

x10 x10 500K AR-202LD

x1x150K AR-202DM

AR-M207 M165 M162 CONSUMABLE PARTS 3-1

2. Environmental conditions

A. Transport conditions

(1) Transport conditions

3. Production number identification

The label on the toner cartridge shows the date of production.

Humidity (%)

Temperature

(2) Storage conditions

Humidity (%)

Temperature

Ver.No.Production

place

Serial

number

Year/ Month/ Day

The lot number, printed on the front side flange, is composed of 6 digits, each digit showing the following content:

123456

B. Use conditions

Use environment conditions

Humidity (%)

Temperature

C. Life(packed conditions)

Photoconductor drum (36 months from the production month) Developer, toner (24 months from the production month)

1 Alphabet

Indicates the model conformity code. A for this model.

2 Number

Indicates the end digit of the production year.

3 Number or X, Y, Z

Indicates the month of packing. X stands for October, Y November, and Z December.

4/5 Number

Indicates the day of the month of packing.

6 Alphabet

Indicates the production factory. "A" for Nara Plant, “C“ for SOCC

AR-M207 M165 M162 CONSUMABLE PARTS 3-2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

1 USB 2.0 port (USB-2)

(when the dual function board is installed) 2 USB 1.1 port (USB-1) Connect to your computer to this port to use the printer and scanner functions. 3 Parallel port Connect to your computer to this port to use the printer function. 4 Charger cleaner Use to clean the transfer charger. 5 Glass cleaner Use to clean the original scanning glass. 6 Document glass Place an original that you wish to scan face down here. 7 Handles Use to move the machine. 8 Power switch Press to turn the machine power on and off. 9 Center tray Copies and printed pages are output to this tray.

10 Upper tray (when the job separator tray kit is installed) Received faxes (when the fax option is installed) and print jobs are deliv ered to this

11 Operation panel Contains operation keys and indicator lights. 12 Front cover Open to remove paper misfeeds or replace the toner cartridge. 13 Tray 1 Tray 1 can hold approximately 250 sheets of copy paper (64 g/m²). 14 Tray 2 Tray 2 can hold approximately 250 sheets of copy paper (64 g/m²). 15 Document cover (when installed) Open to make a copy from the document glass. 16 Side cover Open to remove misfed paper. 17 Side cover handle Pull to open the side cover. 18 Bypass tray guides Adjust to the width of the paper when using the bypass tray. 19 Bypass tray Special paper (heavy paper or transparency film) can be fed from the bypass tray. 20 Bypass tray extension Pull out when feeding large paper such as 11" x 17" and 8-1/2" x 14" (A3 and B4).

14 13

Connect to your computer to this port to use the printer and scanner functions.

tray.

18 19 20

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1

2. Internal

23 24

2728

29 30

31 32

21 T oner cartridge lock release lever To replace the toner cartridge, pull out the toner cartridge while pushing on this lever. 22 Toner cartridge Contains toner. 23 Document feeder tray (when the SPF is installed) Place the original(s) that you wish to scan face up here. Up to 40 sheets can be

24 Original guides (when the SPF is installed) Adjust to the size of the originals. 25 Feeding roller cover (when the SPF is installed) Open to remove misfed originals. 26 Right side cover (when the SPF is installed) Open to remove misfed originals. 27 Fusing unit release levers To remove the paper misfed in the fusing unit, push down on these levers and

28 Roller rotating knob Rotate to remove misfed paper. 29 Exit area (when the SPF is installed) Originals exit the machine here after copying/scanning when the SPF is used. 30 Reversing tray (when the RSPF is installed) Pull out to remove misfed originals. 31 Photoconductive drum Images are formed on the photoconductive drum. 32 Fusing unit paper guide Open to remove misfed paper.

Warning: The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or injury. Caution: Do not touch the photoconductive drum (green portion) when rem oving the misfed paper. Doing so may damage the drum and cause

smudges on copies.

Note: The model name is on the front cover of the machine.

placed.

remove the paper.

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2

3. Operation panel

2134

26 27 28 29 30

ABCDE

31 32 33 34 35

FGH I J

36 37 38 39 40

KLMNO

41 42 43 44 45

PQR TS

46 47 48 49 50

U V W XYZ SP

SPEAKER

REDIAL/PAUSE SPEED

SHIFT

COMM. SETTING

SYMBOL

SPACE/

COPY

SCAN

FAX

ON LINE

LINE

DATA

1 Keys for fax function (when the fax option is installed) These are used in fax mode. 2 [COPY] key/indicator Press to select copy mode. If pressed when "Ready to copy." appears or during

warm-up, the total number of sheets used appears while the key is pressed.

3 [PRINT] key/indicator Press to select print mode.

• ONLINE indicator Print jobs can be received when this indicator is lit.

• DATA indicator This lights steadily when there is a print job in memor y that has not been print ed, and blinks during printing.

4 [SCAN] key/indicator Press to select scan mode. 5 Display Shows various messages. For more information see page 5-5. 6 [BACK] key Press to return the display to the previous screen. 7 [FAX STATUS] key This key is used in fax mode. 8 [OK] key Press to enter the selected setting. 9 Copy number display The selected number of copies appears. During copying, this shows the remaining

number of copies. 10 Numeric keys U se to select the number of copies. 11 [INTERRUPT] key/INTERRUPT indicator Interrupts a copy run to allow an interrupt copy job to be performed. 12 [C] key Press to clear the set number of copies or stop a copy run. 13 Information lamp

(when the fax option is installed)

14 [FAX] key/indicator (when the fax option is installed)

Information lamp blinks, when facsimile is received, or when the paper remains in

the tray.

This key is used in fax mode.

LINE indicator, DATA indicator

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-3

For U.S.A.

5967 8 1011 12

FAX STATUS

For other country

COPY

EXPOSURE

PAPER ZOOM

SCAN

COLOR MODE

RESOLUTION

FAX

PROGRAM

ADDRESS FORMAT ADDRESS

RESOLUTION

BROADCAST

15 16 17 18 19

5967 8 1011 12

AUTO %

OUTPUT DUPLEX

ORIGINAL SIZE DUPLEX SCAN ORIGINAL SIZE

BACK

DUPLEX SCAN

SPECIAL FUNCTION

21 22 27262523 24

FAX STATUS

BACK

ACC. #-C

ABC DEF

JKLGHI MNO

TUVPQRS WXYZ

@.-

READ-END

ABC DEF

JKLGHI MNO

TUVPQRS WXYZ

PAPER

COPY

SCAN

COLOUR MODE

FAX

EXPOSURE

PROGRAM

COPY

SELECT

RATIO

RESOLUTION

ADDRESS

BROADCAST

15 16 17 18 19

AUTO

IMAGE

FORMAT

2-SIDED

OUTPUT

COPY

SPECIAL FUNCTION

ORIGINAL SIZE DUPLEX SCAN

21 22 27262523 24

ACC. #-C

@.-

READ-END

15 [EXPOSURE] key Use to select the exposure mode. "AUTO", "TEXT", or "PHOTO" can be selected. 16 [PAPER] key (PAPER SELECT key) Use to manually select a paper tray. 17 [ZOOM] key (COPY RAT IO key) Press to select a reduction or enlargement copy ratio. 18 [AUTO%] key (AUTO IMAGE key) Press to have the copy ratio selected automatically. 19 [SORT] key (Only effective when the dual function

Use to select the sort function.

board is installed)

20 [DUPLEX] key (2-SIDED COPY key) (only on models

Select the two-sided copying mode.

that support two-sided printing)

21 Arrow keys Press to move the highlighting (which indicates that an item is selected) in the

display. 22 [SPECIAL FUNCTION] key Press to select special functions. 23 [ACC.#-C] key Press the end the use of an account and return the display to the account number

entry screen. 24 [0] key Press during a continuous copy run to display the number of copies completed. 25 [READ-END] key When copying in sort mode from the document glass, press this key when you have

finished scanning the original pages and are ready to start copying. 26 [START] key/indicator Copying is possible when this indicator is on. Press the key to start copying. 27 [CA] key Clears all selected settings and returns the machine to the default settings.

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-4

4. Display(base screen)

Example: Copy mode

23 4

Ready to copy.

AUTO

100%

8 x11

AUTO

Icons appearing in the special function icon display

1-sided to 2-sided copy

2-sided to 2-sided copy

2-sided to 1-sided copy

Center erase copy*

Edge + Center erase*

2 in 1 copy*

Sort function* 4 in 1 copy*

Margin shift copy* Dual page copy

* The display shown is the AR-M207 (when the optional

RSPF is installed) display.

* These only appear when the dual function board is

1 Exposure display Indicates the selected exposure mode. 2 Special function icon display Icons of enabled special functions will appear. 3 Message display Messages are displayed regarding machine status and operation. 4 Original size display The size of the placed original and the icon of the original scanning mode will

appear.

: One-sided scanning in the SPF. : Scanning on the document glass

: Two-sided scanning in the RSPF. 5 Copy ratio display Displays the copy ratio for reduction or enlargement. 6 Paper size display Displays the selected paper size. When "AUTO" appears, the most suitable size of

paper is automatically selected.

7 Paper tray display The selected paper tray is highlighted.

Erase copy* Card shot*

installed.

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-5

5. Motor, solenoid, clutch

5 6 7

9 10

11 12 13

No.

1 Mirror motor MRM Drives the optical mirror base (scanner unit). 2 Shifter motor SHTM Shifts the paper exit tray. 3 Toner motor TM Toner supply 4 Duplex motor DPX Switchback operation and paper exit motor in duplex. 5 Cooling fan motor CFM Cools the inside of the machine. 6 Main motor MM D r ives the machine. 7 1st tray paper feed clutch CPFC1 Drive the pick up roller 8 PS clutch RRC Drives the resist roller

9 Paper feed solenoid CPSOL1 Solenoid for paper feed from cassette 10 Resist roller solenoid RRS Resist roller rotation control solenoid 11 Manual paper transport clutch MPTC Drives the manual paper transport roller. 12 Manual paper feed clutch MPFC Drives the manual paper feed roller. 13 Manual paper feed solenoid MPFS Manual paper feed solenoid 14 2nd tray transport clutch CPFC2 Dr i ves the 2nd tray transport roller. 15 2nd tray transport solenoid FSOL1 2nd tray transport solenoid 16 2nd tray paper feed clutch CPFC 1 Drives the 2nd tray paper feed roller. 17 2nd tray paper feed solenoid PSOL2 2nd tray transport solenoid 18 Exhaust fan motor VFM Cools the inside of the machine. 19 Job separator motor Job separator tray up/down

Name

Code

Function operation

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-6

6. Sensor, switch

No. Name Code Function operation

1 Mirror home position sensor MHPS Detects the mirror (scanner unit) home position. 2 Side door switch DSWR Side door open detection 3 Paper exit sensor (paper exit side) POD1 Detects paper exit. 4 Shifter home position sensor SFTHP Shifter home position detection 5 Paper exit sensor (DUP side) PDPX Paper transport detection 6 Thermistor RTH Fusing section temperature detection 7 Thermostat Fusing section abnormally high temperature detection 8 Toner density sensor TCS Toner quantity detection

9 2nd tray detection switch 2nd tray detection 10 Manual sensor MPED Manual transport detection 11 2nd tray door open/close sensor DRS2 2nd tray door open/close detection 12 2nd tray door paper pass sensor PPD2 2nd tray paper entry detection 13 2nd tray paper empty sensor CSS2 2 nd tray paper empty detection 14 Paper in sensor PIN Paper transport detection 15 Cassette empty Tray paper entry detection 16 Front cover SW Front cover open detection 17 Power switch MAIN SW Turns ON/OFF the main power source. 18 Tray full sensor TRAY-D Tray full detection 19 Job separator paper presence/empty

sensor 20 Job separator HP sensor LFT UP Job separator HP detection 21 Lower limit switch / JOBS_DLD Job separator tray lower limit position detection 22 OC sensor OCSW Original cover and SPF open/close detection 23 Original size sensor(Main Scaning) DSIN0 Original size detection 24 Original size sensor(Sub Scaning) DSIN1 Original size detection

TRAY-FULL Job separator tray paper presence/empty detection

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-7

7. PWB unit

No. Name Function operation

1 Copy lamp Inverter PWB Copy lamp control 2 I / F PWB USB1.1, IEEE1284 I/F 3 CCD sensor PWB Image scanning 4 Main control PWB Main control PWB 5 Tray PWB Shifter motor control 6 IMC2 PWB Electronic sort, USB2.0 << Option:AR -EB 9>> 7 2nd cassette PWB 2nd cassette control 8 High voltage PWB High voltage control

9 Power PWB AC power input/DC power control 10 Operation main PWB Operation panel input/Display, operation panel section control 11 LCD OPE PWB Display and operation panel control 12 FAX • KEY PWB FAX operation input, key operation input<< Option:AR-FX11>> 13 FAX main PWB F AX control<< Option:AR-FX11>>

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-8

8. Cross sectional view

7 8

9 10

11 12 13 14

No. Name Function/Operation

1 Copy lamp Image radiation lamp 2 Copy lamp unit Operates in synchronization with No. 2/3 mirror unit to radiate documents

3 LSU unit Converts image signals into laser beams to write on the drum. 4 Lens unit Reads images with the lens and the CCD. 5 MC holder unit Supplies negative charges evenly on the drum. 6 Paper exit roller Used to discharge paper. 7 Transport roller Used to transport paper. 8 Upper heat roller Fuses toner on paper (with the Teflon roller).

9 Lower heat roller Fuses toner on paper (with the silicon rubber roller). 10 Waste toner transport roller Transports waste toner to the waste toner box. 11 Drum unit Forms images. 12 Transfer charger unit Transfer images (on the drum) onto paper. 13 DUP follower roller 14 Duplex transport roller Transports paper for duplex . 15 Resist roller Takes synchronization between the paper lead edge and the image lead edge. 16 Manual paper feed tray Manual paper feed tray 17 Manual paper pick up roller Picks up paper in manual paper feed. 18 No. 2/3 mirror unit Reflects the images from the copy lamp unit to the lens unit. 19 Manual transport roller Transports paper from the manual paper feed port. 20 2nd tray paper transport roller Transports paper from the 2nd tray. 21 2nd tray paper pick up roller

(semi-circular roller)

22 1st tray paper feed roller

(semi-circular roller)

23 MG roller Puts toner on the OPC drum.

sequentially.

Picks up paper from the 2nd tray.

Picks up paper from the 1st tray.

AR-M207 M165 M162 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-9

[5] UNPACKING AND INSTALLATION

1. Installing conditions

A. Copier installation

Do not install your copier in areas that are:

•damp, humid, or very dusty

•exposed to direct sunlight

•poorly ventilated

•subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

•Be sure to allow the required space around the machine for servicing and proper ventilation.

B. Power source

•Use an exclusive-use power outlet. If the power plug of this machine is inserted into a power outlet commonly used with other illumination units, flickers of the lamp may be result. Use a power outlet which is not used commonly with any illumination units.

•Avoid complex wiring.

C. Grounding wire connection.

•To avoid danger, be sure to connect a grounding wire. If no grounding wire is connected and a leakage occurs, a fire or an electric shock may be result.

2) Open the front cover.

•Hold the both sides and pull down to open.

3) Loosen the screw and remove the developer cartridge.

4) Remove the developer tank from the developer cartridge.

2. Removal of protective material and fixing

screw

1) Remove all tapes and protective material.

• Remove all tapes, then open the document cover and remove the protective material of sheet shape

2) Remove the fixing screw.

•Use a coin to remove the fixing screw.

•The fixing screw is required when transporting the machine. Keep it in the tray. (Refer to the later description.)

3.Installing procedure

A.Developer cartridge installation

1) Open the manual tray, and open the side cover.

5) Supply developer into the developer tank while rotating the MG roller in the arrow direction.

MG roller

* Shake the developer bag enough before opening it.

Hook

Note: Check that the DV seal is free from developing agent. If developing

agent is attached to the DV seal, clean it carefully. Check to insure that the hook is engaged in two positions.

6) Attach the developer tank to the developer cartridge.

* After supplying developer into the developer cartridge, do not tilt or

shake the developer cartridge.

7) Attach the developer cartridge to the copier, and fix it with the screw.

AR-M207 M165 M162 UNPACKING AND INSTALLATION 5-1

B. Toner cartridge installation

1) Shake the toner cartr idge several times horizontally, and rem ove the tape.

* Do not hold the shutter lever when shaking. * After removing the tape, do not tilt or shake the toner cartridge.

4 or 5 times

Shutter

4. Removal and storage of fixing screw

1) Lift the knob and gently pull out the tray .

Handle

2) Attach the toner cartr idge to the copier.

3) Pull the shutter lever.

Tape

2) Hold the paper pressure plate and turn t he fixing screw in the arrow direction.

3) Store the fixing pin and the fixing screw in the tray.

•Store the fixing screw which was removed in the abov e procedure 2 and

the fixing screw which was removed in procedure 2 of 2.

•Removal of protective material and fixing screw in the storage place in

the tray.

Pressure

plate

lock

Screw

Close the front cover A, then close the side cover B.

•When closing the front cover, gently press the both sides.

•When closing the side cover, hold the knob.

• When closing the covers, be sure to close the front cover first, then close the side cover. If closed in a wrong sequence, the covers may be broken.

AR-M207 M165 M162 UNPACKING AND INSTALLATION 5-2

5. Changing the paper size setting of a tray

DUPLEX

SPECIAL FUNCTION

ACC.

DUPLEX SCAN DUPLEX SCAN

PQR

DUPLEX

SPECIAL FUNCTION

GHI

BACK

If the size of the loaded paper is different from the size shown in the display, follow the steps below to change the paper size setting of the tray. The paper size setting cannot be changed during copying, printing, fax printing (when the fax option is installed), or interrupt copying, or when a misfeed has occurred. However, if the machine is out of paper or out of toner, the paper size setting can be changed during copying, printing, and fax printing. The paper size cannot be set for the bypass tray.

4) Press the [ ] or [ ] key to select the paper tray for which the paper size is being changed.

Example: Tray 2

PAPER SIZE SET

8 x11 11x17 11x17 8 x14 8 x11 8 x11R

1) Press the [SPECI AL FU NCTION] key.

SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET

The special function screen will appear.

The screen shown above is the copy mode screen.

2) Press the [ ] or [ ] key to select "PAPE R SI ZE SET ".

DISPLAY CONTRAST

SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST

3) Press the [OK] key.

PAPER SIZE SET

8 x11R 11x17

11x17 8 x14 8 x11

The paper size setting screen will appear.

8 x11R

5) Press the [ ] key.

PAPER SIZE SET

8 x11 11x17 11x17 8 x14 8 x11 8 x11R

The cursor moves to the paper size selection position on the right.

6) Press the [ ] or [ ] key to select the paper size.

Example: Selecting 8-1/2" x 14" size

PAPER SIZE SET

8 x11 11x17 11x17 8 x14 8 x11 8 x11R

To change the size of another paper tray, press the [ ] key and then repeat steps 4 to 6.

7) Press the [OK] key.

A message asking you to confirm the new paper size setting will appear.

8) Press the [OK] key. The selected paper size will be stored and the display will return to the base screen.

Note

: Shows tray "1". : Shows tray "2".

Note Affix the paper size label for the paper size selected in step 6 to the label position on the right end of the tray.

AR-M207 M165 M162 UNPACKING AND INSTALLATION 5-3

+ 110 hidden pages