Sharp AR-F14 Owner's Manual
MODEL
AR-F14
SADDLE STITCH FINISHER
OPERATION MANUAL
SADDLE STITCH FINISHER
•
• PARTS OF THE SADDLE
Page
1
STITCH FINISHER
• SPECIFICATIONS
•
FUNCTIONS OF THE SADDLE
STITCH FINISHER
•
USING THE SADDLE STITCH
FINISHER FUNCTIONS
•
USING THE SADDLE STITCH
FINISHER TO MAKE COPIES
•
REPLACING THE STAPLE CARTRIDGE
AND REMOVING STAPLE JAMS
•
REMOVING PAPER MISFEEDS
• TROUBLESHOOTING
• USING THE KEY OPERATOR
PROGRAMS
1
2
3
5
6
8
11
14
15
For users in the USA
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This equipment complies with the requirements of Directive 89/336/EEC as amended by
93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinie 89/336/EWG mit Änderung
93/68/EWG.
Ce matériel répond aux exigences contenues dans la directive 89/336/CEE modifiée par la
directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijn 89/336/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC med tillæg nr. 93/68/EEC.
Quest’apparecchio è conforme ai requisiti della direttiva 89/336/EEC come emendata dalla
direttiva 93/68/EEC.
Este equipamento obedece às exigências da directiva 89/336/CEE na sua versão corrigida
pela directiva 93/68/CEE.
Este aparato satisface las exigencias de la Directiva 89/336/CEE, modificada por medio de la
93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjen 89/336/EEC så som kompletteras av
93/68/EEC.
Dette produktet oppfyller betingelsene i direktivet 89/336/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivin 89/336/EEC vaatimukset, jota on muutettu direktiivillä
93/68/EEC.
The CE mark logo label is affixed on an equipment in case that the directives described in the
above sentence are applicable to the product. (This sentence is not applicable in any country
where the above directives are not required.)
SADDLE STITCH FINISHER
The saddle stitch finisher features the offset function, which makes it easy to distinguish sets of output, and the
saddle stitch (pamphlet) function, which automatically staples and folds output down the center. An optional punch
unit can also be installed to punch holes in output.
PARTS OF THE SADDLE STITCH FINISHER
Staple section
Open the front cover and
pull out this section to
replace the staple
cartridge or remove a
staple jam.
Stapler compiler
Paper to be stapled is
temporarily stacked here.
Offset tray
This tray is used for the offset
function and the staple function.
Saddle stitch tray
Saddle stitch (Pamphlet) output
is delivered to this tray.
Front cover
Open this cover to replace the
staple cartridge or remove a
staple jam.
• Do not press down on or place heavy objects on the saddle stitch finisher (or on its trays in
Caution
particular).
• During output to the offset tray, the offset tray may move up and down.
Top cover
Open this cover to remove a paper misfeed.
Center cover
Paper moves through
here when output to the
saddle stitch finisher.
Detach button
Press this button when a
paper misfeed or other
problem occurs to
detach the saddle stitch
finisher from the
machine.
Display screens, messages, and key names shown in this manual may differ from the actual screens, messages,
and key names due to modifications made for improvement.
This operation manual is described based on the American spelling standard.
1
SPECIFICATIONS
Name Saddle Stitch Finisher
Number of trays 2
Paper output Face down (when using the offset tray)
Tray types Upper tray: Offset tray Lower tray: Saddle stitch tray
Tray capacity Upper tray:
Without stapling
Stapling
Lower tray (saddle stitch): Number of pages that can be stapled 10 sets x 6-10 pages
Paper size Upper tray: 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
Lower tray (saddle stitch): 11" x 17", 8-1/2" x 11"R, A3, B4, A4R
Paper weight Upper tray: 16 lbs. to 54 lbs. (60 g/m
Lower tray (saddle stitch): 16 lbs. to 28lbs. (60 g/m
Paper type Upper tray: plain paper, heavy paper, letterhead paper, recycled paper, color paper
Lower tray (saddle stitch):plain paper, letterhead paper, recycled paper, color paper
Paper full detection Upper tray / lower tray (saddle stitch): Yes
8-1/2" x 11" / A4 size or less (21 lbs.(80 g/m2)): 1000 sheets maximum
8-1/2" x 13" / B4 size or greater (21 lbs.(80 g/m
8-1/2" x 11" / A4 size or less
8-1/2" x 13" / B4 size or greater
per set, or 20 sets x 1-5 pages per set
5-1/2" x 8-1/2", A3, B4, A4, A4R, B5, B5R, A5
(21 lbs. (80 g/m2))
(21 lbs. (80 g/m2))
2
to 200 g/m2)
2
to 105 g/m2)
2
)): 500 sheets maximum
: 30 sets and 1000 sheets maximum
: 30 sets and 500 sheets maximum
Offset function Upper tray only
Allowed paper sizes
for stapling
Number of pages that
can be stapled
Stapling positions Upper tray: 3 positions (top left staple, two left staples, lower left staple)
Paper feeding Center reference
Power supply From power unit of multifunction machine
Dimensions 28-1/32" (W) x 23-3/4" (D) x 40-3/64" (H)(712 mm (W) x 603 mm (D) x 1017 mm (H))
Weight Approx. 101.4 lbs. (46 kg)(finisher: 86 lbs. (39 kg), joint: 15.4 lbs. (7 kg))
Name Punch module
Model*
Number of holes 23 or 24 4
Paper sizes for hole
punching
1
Upper tray: 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, B5R
Lower tray (saddle stitch): 11" x 17", 8-1/2" x 11"R, A3, B4, A4R
8-1/2" x 11", A4 or smaller: 50 pages (21 lbs. (80 g/m
8-1/2" x 13", B4 or greater: 25 pages (21 lbs. (80 g/m
Lower tray (saddle stitch): 4-23/32"(120 mm) pitch from center of paper
(two trays or four trays installed)
28-1/32" (W) x 23-3/4" (D) x 36-7/64" (H)(712 mm (W) x 603 mm (D) x 917 mm (H)
(three trays installed)
AR-PN1A AR-PN1B*
11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
A3, B4, A4, A4R,
B5, B5R
3 holes: 11" x 17",
8-1/2" x 11", A3, A4
2 holes: 8-1/2"x14",
8-1/2" x 13",
8-1/2" x 11"R
2
A3, A4 11" x 17",
2
))
2
))
AR-PN1C*
3
AR-PN1D*
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
A3, B4, A4, A4R,
B5, B5R
3
*1 Multiple punch modules cannot be installed together. Some models may not be available in some regions.
*2 With AR-PN1B, two or three holes can be punched depending on the paper size.
*3 With AR-PN1C and AR-PN1D, the number of holes is the same. The hole interval, however, is not the same.
Diagrams and contents are subject to change without notice.
2
Supplies
The following staple cartridge is required as a supply for the saddle stitch finisher:
● AR-SC2
Staple Cartridge (approx. 5000 staples x 3)
FUNCTIONS OF THE SADDLE STITCH FINISHER
■
Sort function
Collates printed pages
OutputOriginals
■
Offset function
Offset function "ON" Offset function "OFF"
■
Staple sort function
Each set of output is collated by the sort function, stapled, and delivered to the upper (offset) tray.
Three stapling positions are available: top left staple, two left staples, or lower left staple.
■
Saddle stitch (Pamphlet stapling) function
■
Group function
Groups printed pages by page
The offset function offsets each set of output from
the previous set for easy separation. (On the
saddle stitch finisher, the offset function is only
possible using the offset tray.)
The offset function does not operate when the
staple sort function is selected.
OutputOriginals
Each set of output is stapled in two places along
the centerline of the paper, folded (with the side
facing up inside), and delivered to the lower (saddle
stitch) tray. In the factory default settings, the
saddle stitch finisher is set to staple and fold sets
after "Pamphlet copy" is performed. If desired, the
"Pamphlet copy" function can be disabled using the
key operator programs.
Note
"Pamphlet copy" is used to copy two originals onto the front side and two originals onto the back side of each
sheet of paper for easy creation of a pamphlet (See the operation manual for copier).
3
■
Punch function (only when a punch unit is installed)
When an optional punch unit is installed on the
saddle stitch finisher, holes can be punched in the
output. Punched output is delivered to the offset
tray.
The punch function cannot be used in combination
with the saddle stitch (pamphlet stapling) function.
For paper sizes that can be punched, see the
specifications on page 2.
Caution
• The following types of paper cannot be stapled:
Transparency film, heavy paper, label sheets, envelopes, postcards, thin paper
• The following types of paper cannot be punched:
Transparency film, label sheets, envelopes, postcards, thin paper
• Be sure to select the same paper size for the output. Stapling and punching are not possible
when different sizes are mixed together. Note, however, that if the widths are the same, the
"mix size original feeding mode"* function can be used to staple and punch different sizes of
paper (saddle stitch is not possible).
* Stapling and punching are not possible if "mix size original feeding mode" includes sizes
that cannot be stapled (such as 5-1/2" x 8-1/2" and A5).
[Example]
Original 1
Original 2 Punch hole positions
Punch hole positions
4
Loading...