Sharp AN-46SP2, AN-52SP2 INSTALLATION MANUAL
SPEAKER UNIT FOR LCD MONITOR
Attaching the Speaker Unit
INSTALLATION MANUAL
Congratulations on your purchase!
As you enjoy your new product, please keep this installation manual in mind.
•
AN-52SP2 is for exclusive use with the TL-M5200 model LCD monitor.
•
AN-46SP2 is for exclusive use with the TL-M4600 model LCD monitor.
Supplied Accessories
If any component should be missing, please contact your dealer.
Speaker unit (x1) Speaker unit fi xing bracket
(x2)
Screw for the speaker unit
attachment (x4)
Flat head screw for the
speaker unit fi xing bracket (x8)
Cable fi xing clamp (x4)
MODEL
AN-52SP2
AN-46SP2
Rubber cushion (x2)
Installation manual
(this document)
Attach the speaker unit fi xing brackets.
1.
Attach the speaker unit fi xing brackets to the LCD monitor by using the supplied fl at head screws.
2.
Fit the supplied rubber cushions into the holes of the speaker unit fi xing brackets.
Attach the speaker unit.
3.
Attach the speaker unit to the LCD monitor by using the supplied screws.
Specifi cations
Item AN-52SP2 AN-46SP2
Principle Two-way, Woofer (100 x 40 mm) x 4 + Tweeter (20 mm) x 2
Power Capacity 15 W (4 Ω) x 2
5
/8” (W) x 3” (D) x 353/64” (H) 4117/64” (W) x 3” (D) x 353/64” (H)
4861/64” (W) x 363/64” (D) x 3023/32” (H) 4343/64” (W) x 411/64” (D) x 2711/16” (H)
Speaker unit
With LCD Monitor
Dimension 46
Weight 4.5 lbs./2.0 kg 4.0 lbs./1.8 kg
Dimension
Weight 66.2 lbs./30.0 kg 52.5 lbs./23.8 kg
Preparation
•
Before performing work spread cushioning over the base area to lay the monitor on. This will
prevent it from being damaged.
•
Before attaching the speaker unit to the LCD monitor, please make sure to switch off the LCD
monitor’s power and disconnect the power plug from outlet.
•
If the setup stand included with the LCD monitor has been attached to the monitor, remove it
before starting the procedure.
Caution
•
Do not apply strong force onto the speaker grille.
•
If, due to insuffi cient attachment or poor handling, the speaker unit falls or is damaged, please
note that we will not bear any responsibility.
4.
Connect the speaker unit cables.
Connect the speaker unit cables to the appropriate speaker connection terminals of the LCD monitor.
R
L
•
With the tab depressed, insert the
tip of the cable.
•
Connect the red cable to the red
connection terminal (+) and the
black cable to the black connection
terminal (-).
NOTE:
•
Be sure to properly connect the +/- and left/right of the speaker unit cables.
•
Avoid short circuiting the + and - terminals.
•
To detach the speaker unit, perform the steps in reverse order.
Attach the supplied cable clamps to the speaker unit.
5.
Remove the seal from the cable clamp and attach the clamp to the speaker unit in the position shown in
the fi gure below (4 positions).
•
Remove the seal and attach the
clamps.
Precautions when transporting the LCD monitor.
•
Do not hold onto the attached optional speakers when transporting the monitor.
Printed in China
TINS-D772WJZZ
08P06-CH-NS
Route the speaker unit cables through the cable clamps.
6.
•
Place the cable on the clamp and
then close the clamp to secure the
cable.
Loading...