Sharp 45D40U - LC - 45"" LCD TV, LC-40C45U, LC-45D40U Service Manual

Download

Page 1

TopPage

LC-40C45U

SERVICE MANUAL

No. S46S5LC40C45U

LCD COLOR TELEVISION

MODEL

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

LC-40C45U

OUTLINE

This model is based on the LC-45D40U and is changed some parts. This Service Manual covers the modifications alone. For the other points, refer to the LC-37/45D40U Service Manual.

CONTENTS

LIST OF CHANGED PARTS

LC-40C45U .........................................................i

SAFETY PRECAUTION

IMPORTANT SERVICE SAFETY PRE-

CAUTION ........................................................... ii

PRECAUTIONS A PRENDRE LORS DE

LA REPARATION.............................................. iii

PRECAUTIONS FOR USING LEAD-FREE

SOLDER ........................................................... iv

CHAPTER 1. SPECIFICATIONS

[1] SPECIFICATIONS ......................................... 1-1

CHAPTER 2. OPERATION MANUAL

[1] OPERATION MANUAL .................................. 2-1

CHAPTER 3. DIMENSIONS

[1] DIMENSIONS ................................................ 3-1

Parts Guide

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

Page 2

LC-40C45U

Service Manual

LIST OF CHANGED PARTS

LC-40C45U

Ref. No. Description LC-45D40U LC-40C45U Note

PWB ASSEMBLIES

MAIN Unit DUNTKD640FM07 DUNTKD640FM14 No parts changed LED Unit DUNTKD641FM07 DUNTKD641FM14 No parts changed IF Unit DUNTKD643FM07 DUNTKD643FM14 No parts changed KEYUnit DUNTKD716FM07 DUNTKD716FM14 No parts changed AC INLET Unit DUNTKD726FM07 DUNTKD726FM14 No parts changed POWER SUPPLY Unit RDENCA166WJQZ — —

LCD PANEL

45” WIDE LCD Panel Module Unit R1LK445T3LZ10 — —

CABINET AND MECHANICAL PARTS Please refer to a Parts list.

PACKING PARTS AND ACCESSORIES Please refer to a Parts list.

Page 3

LC-40C45U

Service Manual

SAFETY PRECAUTION

IMPORTANT SERVICE SAFETY PRECAUTION

WARNING

1. For continued safety, no modification of any circuit should be attempted.

2. Disconnect AC power before servicing.

BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)

Before returning the receiver to the user, perform the following safety checks:

3. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the chassis and other metal parts in the receiver.

4. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.

5. To be sure that no shock hazard exists, check for leakage current in the following manner.

• Plug the AC cord directly into a 120 volt AC outlet.

• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.

• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.

• Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must be used only for the purpose of completing these checks.)

Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the monitor to the owner.

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

SAFETY NOTICE

Many electrical and mechanical parts in LCD color television have special safety-related characteristics.

These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc.

Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features

are identified by " " and shaded areas in the Replacement Parts List and Schematic Diagrams.

For continued protection, replacement parts must be identical to those used in the original circuit.

The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards.

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:

CAUTION: FOR CONTINUED

PROTECTION AGAINST A RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE.

F7801 (8A, 250V), F702, F703 (5A, 125V) F4701, F4703, F5701 (3A~, 250V, 115

DVM

AC SCALE

1.5k ohm 10W

TO EXPOSED METAL PARTS

CONNECT TO KNOWN EARTH GROUND

0.15µF

TEST PROBE

Page 4

LC-40C45U

iii

PRECAUTIONS A PRENDRE LORS DE LA REPARATION

De nombreuses pièces, électriques et mécaniques, dans les téléviseur ACL présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont identifiées par la marque " " et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques.

Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas les mêmes caractéristiques que les pièces recommandées par l'usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.

AVERTISSEMENT

•

Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants.

N'entreprendre aucune modification de tout circuit. C'est dangereux.

Débrancher le récepteur avant toute réparation.

Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.

Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistancecapacité, les isolateurs mécaniques, etc.

S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante:

Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour cet essai).

A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ 10 watts en parallèle avec un condensateur de 0.15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre.

Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance.

Toucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0.5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client.

VERIFICATIONS CONTRE L'INCEN-DIE ET LE CHOC ELECTRIQUE

Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes.

DVM

ECHELLE CA

1.5k ohm 10W

0.15

SONDE D'ESSAI

AUX PIECES METALLIQUES EXPOSEES

BRANCHER A UNE TERRE CONNUE

AVIS POUR LA SECURITE

PRECAUTION:POURLA

PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE

F7801 (8A, 250V), F702, F703 (5A, 125V) F4701, F4703, F5701 (3A~, 250V, 115

Page 5

LC-40C45U

PRECAUTIONS FOR USING LEAD-FREE SOLDER

Employing lead-free solder

• "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.

Example:

Using lead-free wire solder

• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.

As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.

Soldering

• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.

Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as required.

If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.

When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.

• Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing

Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.

Part No, Description Code

ZHNDAi123250E J φ0.3mm 250g(1roll) BL ZHNDAi126500E J φ0.6mm 500g(1roll) BK ZHNDAi12801KE J φ1.0mm 1kg(1roll) BM

Page 6

LC-40C45U

1 – 1

LC-40C45U

Service Manual

CHAPTER 1. SPECIFICATIONS

[1] SPECIFICATIONS

Emergency alert messages via Cable are unreceivable.

•

As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

LCD panel

Number of dots

TV Function

TV-standard (CCIR)

Receiving Channel

VHF/UHF

CATV

Digital Terrestrial Broadcast (8VSB)

Audio multiplex

Audio out

Terminals

Rear

INPUT 1

INPUT 2

INPUT 3

INPUT 4

INPUT 5

ANTENNA

DIGITAL AUDIO OUTPUT

OUTPUT

OSD language

Power Requirement

Power Consumption

Weight

Dimension (W H D)

Accessories

Operating temperature

3,147,264 dots (1366 768 3 dots)

American TV Standard ATSC/NTSC System

VHF 2-13ch, UHF 14-69ch

1-135ch* (non-scrambled channel only)

2-69ch

BTSC System

10W 2

AV in, COMPONENT in

S-VIDEO in, AV in

Audio in, HDMI in with HDCP

HDMI in with HDCP

75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)

Optical Digital audio output 1 (PCM/Dolby Digital)

Audio out

English/French/Spanish

AC 120 V, 60 Hz

Remote control unit ( 1), AC cord ( 1), “AAA” size battery ( 2), Cable clamp ( 1), Cable tie ( 1), Stand unit ( 1), Operation manual ( 1)

32°F to 104°F (0°C to 40°C)

Item

Model: LC-40C45U

45" Advanced Super View & BLACK TFT LCD

with stand

w/o stand

with stand

270 W

64.9 lbs./29.4 kg

70.6 lbs./32.0 kg

/642957/

431/32inch

/643163/64121/64inch

xxx

++ +

Page 7

LC-40C45U

2 – 1

LC-40C45U

Service Manual

CHAPTER 2. OPERATION MANUAL

[1] OPERATION MANUAL

Part names

TV (Front) TV (Rear)

Part names

POWER button

Channel buttons

(CH /)

Volume buttons (

VOL

INPUT button

OPC indicator*

POWER

indicator**

OPC sensor*

Remote control sensor

INPUT 4

terminals

INPUT 3

terminals

AUDIO OUTPUT

terminals

INPUT 5 terminal

DIGITAL AUDIO OUTPUT terminal

Antenna/Cable in

INPUT 1 terminals

INPUT 2 terminals

AC INPUT terminal

Page 8

LC-40C45U

2 – 2

Part names

Remote control unit Removing the stand

Setting the TV on the wall

Appendix

114

19720

11 23

13 27

1 TV POWER: Switch the TV power on or enters standby

mode.

2 DISPLAY: Display the channel information.

3 SOURCE POWER: Turns the power of the external

equipment on and off.

4 External equipment operational buttons: Operate the

external equipment.

5 0–9:Set the channel.

6 • (DOT):

7 INPUT: Select a TV input sourc e. (TV, INPUT 1, INPUT 2,

INPUT3, INPUT 4, INPUT5)

8VOL/:Set the volume.

9 SURROUND: Select Surround settings.

10 FREEZE: Set the still image. Press again to return to

normal screen.

11 EXIT: Turn off the menu screen.

12 SLEEP: Set the sleep timer.

13 AUDIO: Selectsthe MTS/SAP or the audio mode during

multi-channelaudio broadcasts.

14 FUNCTION: Switches the remote control for TV,CBL/

SAT, VCR, DVD and AUDIO operation. Indicator lights up

for the current mode.

* To enter the code registration mode, you need to press

FUNCTION and DISPLAY at the same time.

15 LIGHT : When pressed all buttons on the remote

control unit will light. The lighting will turn off if no

operations are performed within about 5 seconds. This

button is used for performingoperations in low-light

situations.

16 VIEW MODE: Select the screen size.

17 ENT: Jumps to a channel after selecting with the 0–9

buttons.

18 FLASHBACK: Return to the previouschannel or input

external mode.

19 CH / : Select the channel.

20 MUTE: Mute the sound.

21 MENU: Display the menu screen.

22 ////ENTER: Select a desired item on the

screen.

23 RETURN: Returnto the previous menu screen.

24 FAVORITE CH

A, B, C, D: Select four preset favorite channels in four

different categories.

While watching, you can toggle the selected channels by

pressing A, B, C and D

25 FAVORITE: Register favorite channel.

26 CC: Display captions from a closed-caption source.

27 AV M ODE: Selec t an audio o r video set ting . (STANDARD,

MOVIE,GAME, USER, DYNAMIC(Fixed), DYNAMIC.)

Before detaching (or attaching) stand, unplug the AC cord from the AC INPUT terminal.

CAUTION

• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.

Before attaching/detaching stand

• BeforeperformingworkmakesuretoturnofftheTV.

• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being

damaged.

CAUTION

• Installing the TV requires special skill that should only be performed by quali-ed service personnel. Customers

should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or

mounting that results in accident or injury.

Using an optional bracket to mount the TV

• You can ask a quali-ed service professional about using an optional AN-37AG2 bracket to mount the TV to the

wall.

• Carefully read the instructions that come with the bracket before beginning work.

Hangingonthewall

AN-37AG2 wall mount bracket. (See the bracket instructions for details.)

Vertical mounting

About setting the TV angle

Unfasten the four screws used to secure the stand in

place.

Detach the stand from the TV.

(Hold the stand so it will not drop from the edge of the

base area.)

NOTE

• To attach the stand, perform the above steps in reverse order.

Angular mounting

0°LC-40C45U

Angle of TV

hex key

NOTE

• Detach the cable clamp on the rear of the TV when using the optional mount bracket.

Page 9

LC-40C45U

2 – 3

Basic adjustment settings

Menu items

Picture

Setup

Audio

Option

Power Contr ol

Digital Setup

List of menu items to help you with operations

OPC

Backlight

Contrast

Brightness

Color

Tint

Sharpness

Advanced

Color Temp.

Black

3D-Y/C

Monochrome

Film Mode

Range of OPC

EZ Setup

CH Setup

Antenna Setup-DIGITAL

Input Skip

Input Label

Parental CTRL

Position

Picture Flip

Standby Mode

Language

Reset

Treble

Bass

Balance

Surround

Audio Only

Digital Noise Reduction

Input Select

HDMI Setup

Output Select

Quick Shoot

Color System

Caption Setup

Program Title Display

Favorite CH

No Signal Off

No Operation Off

Audio Setup

Page 10

LC-40C45U

3 – 1

LC-40C45U

Service Manual

CHAPTER 3. DIMENSIONS

[1] DIMENSIONS

Unit: inch/(mm)

243/32(612)

/64(1113)

/32(126)

/64(989.1)

(812)

(759)2

(53)

(474)

(556.7)

121/64(305)

/32(104)

77/8(200)

(100)

(200)

Page 11

PartsGuide

LC-40C45U

PARTS GUIDE

No. S46S5LC40C45U

★ MARK: SPARE PARTS-DELIVERY SECTION

CONTENTS

[1] PRINTED WIRING BOARD

ASSEMBLIES (NOT REPLACEMENT ITEM)

[2] LCD PANEL (NOTE: THE PARTS

HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY.)

[3] CABINET AND MECHANICAL

MODEL

PARTS

[4] SUPPLIED ACCESSORIES

[5] PACKING PARTS (NOT

REPLACEMENT ITEM)

[6] SERVICE JIGS

LC-40C45U

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

Page 12

LC-40C45U

NO. PARTS CODE

PRICE

RANK

NEW

MARK

★

DESCRIPTION

[1] PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM)

N DUNTKD640FM14 - R MAIN Unit N DUNTKD641FM14 - X LED Unit N DUNTKD643FM14 - X IF Unit N DUNTKD716FM14 - X KEYUnit N DUNTKD726FM14 - X AC INLET Unit N RDENCA166WJQZ BU X POWER SUPPLY Unit

[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-

DENTLY.)

N R1LK445T3LZ10 GR X 45" WIDE LCD Panel Module Unit

Page 13

[3] CABINET AND MECHANICAL PARTS

58 59

2-1

3-1

3-2

3-4

3-3

4-1

4-2

4-3

5-1

5-2

5-6

2-2

1-1

1-3

1-6

1-2

1-4

1-7

1-5

1-8

1-4

5-3

5-5

5-4

LC-40C45U

Page 14

LC-40C45U

NO. PARTS CODE

PRICE

RANK

NEW

MARK

★

[3] CABINET AND MECHANICAL PARTS

1 CCABAB285WJ02 BS X Front Cabinet Ass'y 1-1 Not Available - - Front Cabinet 1-2 Not Available - - Front Cover 1-3 HBDGBA061WJSA AG X Badge, SHARP 1-4 PSPAHA416WJZZ AC X Mask Spacer, x6 1-5 Not Available - - Spacer 1-6 Not Available - - POP Label 1-7 Not Available - - Spacer, x5 1-8 Not Available - - Spacer

2 CCABBA750WJ01 BS X Rear Cabinet Ass'y 2-1 Not Available - - Rear Cabinet 2-2 LHLDWA131WJKZ AF X Wire Holder

3 CCOVAB497WJ01 BD X Top Cover Ass'y 3-1 Not Available - - Top Cover 3-2 JBTN-A429WJKA AD X Power Button 3-3 Not Available - - Operation Button 3-4 MSPRCA049WJFW AD X Power Button Spring

4 CDAi-A264WJ02 BC X Stand Support Ass'y 4-1 Not Available - - Support Cover 4-2 Not Available - - Stand Support 4-3 Not Available - - Screw Guide, x4

5 CDAi-A246WJ03 BA X Stand Base Ass'y 5-1 Not Available - - Stand Base Cover 5-2 Not Available - - Base Angle 5-3 Not Available - - LEG Cushion-A, x4 5-4 Not Available - - LEG Cushion-B, x4 5-5 XEBS740P10000 AB X Screw, x14 5-6 Not Available - - Stand Label

6 R1LK445T3LZ10 GR X 45" WIDE LCD Panel Module Unit

7 DUNTKD640FM14 - R MAIN Unit

8 DUNTKD641FM14 - X LED Unit

9 DUNTKD643FM14 - X IF Unit

10 DUNTKD716FM14 - X KEYUnit 11 DUNTKD726FM14 - X 12 RDENCA166WJQZ BU X POWER SUPPLY Unit 13 CANGTA317WJ01 AN X Fan Angle Ass'y 14 CANGTA318WJ01 AP X Fan Angle C Ass'y 15 CCHSMA299WJ01 BC X Tray Chasis Ass'y 16 GCOVAA678WJKA AG X SD Card Cover 17 GCOVAB501WJSA AE X LED Cover 18 GCOVAB593WJKA BD X Stand Bottom Cover 19 HiNDPB603WJSA AK X Jack Indicator 20 HiNDPB715WJSA AF X Terminal Label 21 HiNDPB718WJSA AH X Model Label 22 LANGKA644WJFW AL X Jack Angle Long 23 LANGKA680WJN1 AQ X Stand Fix Angle 24 LANGKA681WJFW AR X Stand Sub Angle 25 LANGQA027WJFW AE X AC Inlet Angle 26 LANGTA301WJM1 AS X Center Angle-R 27 LANGTA302WJM1 AS X Center Angle-L 28 LBSHZA005WJZZ AB X Clip, x2 29 LHLDWA096WJKZ AD X Wire Holder (for IF Unit) 30 Not Available - - Screw (for Stand Ass'y), x4 31 Not Available - - Screw (for Stand), x4 32 LX-NZ3047GEZZ AB X Hexiagonal Nut 33 NFANR0126CEZZ AR X Fan, x2 34 PRDARA192WJFW AE X Hest Sink (for AV2) 35 PRDARA312WJFW AE X Hest Sink (for AMP-Top) 36 PRDARA328WJFW AE X Hest Sink 37 PRDARA330WJFW AM X Hest Sink (for PWB) 38 PSLDMA910WJFW AV X MAIN Shield 39 PSPAZA635WJKZ AC X Spacer (Cool Sheet), x3 40 PSPAZA700WJKZ AD X Spacer (Cool Sheet), x3 41 QCNCWA496WJZZ AK X Connector (F-RCA) 42 QCNW-E385WJQZ AL X Connecting Cord (RA) 43 QCNW-E387WJQZ AH X Connecting Cord (LB) 44 QCNW-E391WJQZ AK X Connecting Cord (SP)

QCNW-E677WJQZ AP X Connecting Cord (LA)

45 46 QCNW-E537WJPZ BA X Connecting Cord (LV) 47 RSP-ZA166WJZZ AU X Speaker L 48 RSP-ZA167WJZZ AU X Speaker R 49 Not Available - - No. Label 50 XBBS740P06000 AA X Screw (for Angle), x20 51 XBBS930P06000 AA X Screw (for Cab-B), x4 52 XBPS730P06WS0 AB X Screw (for Angle, PWB), x46 53 XBPS730P20JS0 AB X Screw (for Fan), x4 54 XBPS930P08000 AA X Screw (for HDMI), x2 55 XEBS940P20000 AA X Screw (for Cab-B), x16 56 XEBSN30P10000 AA X Screw (for Angle), x10 57 XEBS930P08000 AA X Screw (for Jack), x3 58 LHLDW1173CEZZ AE X Wire Holder 59 PSLDMA693WJZZ AD X Shield, x2 60 LX-BZA044WJFU AB X Screw (for AC INLET), x2 61 QCNW-E466WJQZ AH X Connecting Cord (AC) 62 QCNW-E279WJQZ AK R Connecting Cord (SH)

AC INLET Unit

DESCRIPTION

Page 15

LC-40C45U

NO. PARTS CODE

PRICE

RANK

[3] CABINET AND MECHANICAL PARTS

63 QCNW-E386WJQZ AF R Connecting Cord (KM) 64 QCNW-E398WJQZ AN R Connecting Cord (PD) 66 QCNW-E465WJQZ AH R Connecting Cord (FD)

[4] SUPPLIED ACCESSORIES

NO. PARTS CODE

[4] SUPPLIED ACCESSORIES

Cable Clamp

Operation manual

PRICE

RANK

X1 LHLDW0110CESD AF X Cable Clamp X2 LHLDWA083WJ00 AD X Cable Band X3 CDAi-A246WJ15 BM X Stand Ass'y X4 QACCDA039WJPZ AR X AC Cord X5 RRMCGA416WJSA BA X Remote Control Unit X6 SSAKA0101GJZZ AC X Polyethylene Bag X7 SSAKHA020WJZZ X Polyethylene Bag (for Screw) X8 TCADEA126WJZZ AC X Enquete Card

X9 TiNS-C413WJZZ AQ X Operation Manual X10 TCAUZA228WJZZ X Caution Card X11 TCAUHA184WJZZ AD X Set up Guide X12 Not Available - - "AAA" Size Battery

NEW

MARK

Cable Band

Stand Ass'y

NEW

MARK

★

X10

AC Cord

X11

X12

★

DESCRIPTION

Remote Control Unit

Page 16

LC-40C45U

[5] PACKING PARTS (NOT REPLACEMENT ITEM)

S5 S7 S9

S10

Page 17

LC-40C45U

NO. PARTS CODE

PRICE

RANK

NEW

MARK

★

[5] PACKING PARTS (NOT REPLACEMENT ITEM)

S1 SPAKCC629WJZZ - - Packing Case

S2 SPAKCC526WJZZ - - Packing Case (Bottom)

S3 SPAKFA973WJZZ - - Stand Case

S4 SPAKL0023CEZZ - - Jyoint, x4

S5 SPAKPA601WJZZ - - Wrapping Paper (Mirror Mat A)

S6 SPAKPA634WJZZ - - Wrapping Paper (Monitor)

S7 SPAKPA646WJZZ - - Wrapping Paper (Mirror Mat C)

S8 SPAKXA992WJZZ - - Packing Add.

S9 SPAKXB017WJZZ - - Stand Pad S10 TLABKA009WJZZ - - No. Label S11 SPAKFA974WJZZ - - Sent-Sheet S12 SPAKKA400WJZZ - - Case S13 SPAKPA512WJZZ - - Mirror Mat S14 SPAKXB028WJZZ - - Frame S15 TLABKA008WJZZ - - No. Label

[6] SERVICE JIGS

N QCNW-C799WJPZ AG J RCA Cable L=1500mm, Tuner to Terminal N QCNW-D483WJQZ AX J 12pins L=1000mm, Main to Power Unit (PE) N QCNW-E068WJQZ AS J 6pins L=1000mm, Main to Power Unit (PD) N QCNW-E670WJQZ AP J 4-8pins L=1000mm, Main to Inverter Unit (LB) N QCNW-E672WJQZ AX J 14-14pins L=1000mm, Power to Inverter Unit (LA) N QCNW-E673WJQZ BE J 32pins L=1000mm, Main to Controller Unit (LV) N QCNW-E674WJQZ AS J 7pins L=1000mm, Main to Controller Unit (SH) N QCNW-E675WJQZ AQ J 5pins L=1000mm, Main to Power Unit (FD)

DESCRIPTION

Page 18

SHARP CORPORATION

AV Systems Group CS Promotion Center Yaita, Tochigi 329-2193, Japan

TQ2020-S

Apr. 2006 Printed in Japan

Design and Production Information Design: Japan Production: SEMEX

SY. KD

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

LC-40C45U