In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
Specifications are subject to change without
prior notice.
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
Page 2
35UF6
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit. The isolated ground system is for
the low B+ DC voltages and the secondary circuit of
the high voltage transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
2
Page 3
2
2
2
IMPORTANT SERVICE SAFETY PRECAUTION
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
(Continued)
35UF6
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Page 4
35UF6
LOCATION OF USER'S CONTROL
L Location of Controls
Front Panel
POWER
Press → On.
Press again → Off.
SENSOR AREA FOR
REMOTE CONTROL
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
Basic Remote Control Functions
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons,
you can program your favorite
programs by using the 4 categories A,
B, C and D. The channels can be
accessed quickly by using these
buttons.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
CATV/DVD-TV/VCR MODE
SELECT SWITCH
In TV/VCR position, sends power and
channel select commands (Channel
up/down and Random Access buttons)
to the TV and VCR control.
In CATV/DVD position, sends power
and channel select commands to a
cable TV converter and DVD control.
DVD/VCR CONTROL
POWERMENU – VOL + CH
POWERMENU – VOL + CH
PULL-OPEN
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
POWER
TV
DVD
VCR
DISPLAY
INPUT
123
456
789
FLASHBACK
PERSONAL PREFERENCE
ABCD
VOL
—
MENUMUTE
REW PLAY FF
PAUSE
ENTER
0
100
CH
CH
CATV TV
DVD VCR
STOP REC
TV • CATV • VCR • DVD
VOL
+
CH/SKIP
TERMINALS
IN 2VIDEO/AUDIO
(INSIDE DOOR)
CHANNEL UP/DOWN
(8) Selects next higher
channel.
(9) Selects next lower
channel.
• Press both at the same
time to access the MAIN
MENU screen.
Infrared Transmitter Window
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
INPUT
Press → Switch to external video
INPUT 1 mode.
Press 2 times → Switch to external video
INPUT 2 mode.
Press 3 times → Switch to external video
INPUT 3 mode or COMPONENT mode.
Press 4 times → Switch back to the
original TV mode.
ENTER
Used in some instances where a Cable
Converter Box requires an “enter”
command after selecting channels,
when using the REMOTE KEYPAD
button.
CHANNEL UP/DOWN
(8) Selects next higher channel.
(9) Selects next lower channel.
• Moves the “a” mark of the MENU
screens.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
Note:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunlight and fluorescent lighting are the most effective when charging the display.
4
Page 5
35UF6
INSTALLATION AND SERVICE INSTRUCTIONS
Note:(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP651 (Pin 3) and make
sure that the voltmeter reads 13.85 ±0.6V DC.
5. Apply external 17.3V DC at TP651 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and plug
the AC cord power on. Now make sure that normal
picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and select the service
adjustment "V11" and Bus data "01" (Y-mute on, CRT
Cut Off).
4. The voltage should be below 35.5kV (at zero beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
5
Page 6
35UF6
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.
2. Service number selection
Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set.
The service adjustment number will vary in
increments of one, from "V01" to "P08". Select the
item you wish to adjust.
3. Data number selection
Press the Vol-up or Vol-down button to adjust the data
number.
DATA NUMBER
SERVICE ADJUSTMENT NUMBER
To enter the service mode and exit service mode.
To enter the service mode manually just press and hold
the Vol-down and Ch-up buttons at the same time, plug
the AC cord into a wall socket.
Now the TV set is switched on and enters the service
mode.
To exit the service mode, turn the television off by
pressing the power button.
Holding down both the VOL-up and CH-up buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2101.
PART REPLACED
IC2001
IC201
IC2101
CRT
IC3001
NECESSARYUNNECESSARY
ADJUSTMENT
X
X
X
X
NOTES
X
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics of parts
including IC201 and MTS level (M01).
Holding down both the VOL-up and CH-up buttons on the TV set in
the service mode for more than 2 seconds will automatically write the
above initial values into IC2101 Then perform a complete adjustment.
Adjust items related to picture tube only.
Adjust items related to MTS only (M01~M20).
SERVICE ADJUSTMENT
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "R01".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note 1 : You will have to come out of the service
mode to select another channel.
Note 2 : Setting the data to "00" will produce a black
raster.
Screen Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "V03" and set the data value to "00" to
set the color level to minimum. (Record original data
code under adjustment "V03" before changing) You
may skip this step, if you selected a B/W picture or
monoscope pattern.
3. Select the service adjustment "V11" and adjust the
data value to "01", this turn off the luminance signal
(Y-mute).
4. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
5. Adjust the service adjustments "V06" red, "V07" green
and "V08" blue to obtain a good grey scale with
normal whites at low brightness level.
6. Select the service adjustment "V11" and reset data
to "00". Select the service adjustment "V03" and reset
data to obtain normal color level.
7. For component input, the data value of "V46" red,
"V47" green and "V48" blue is adjusted to follow the
data value of "V06", "V07" and "V08" respectively.
8. Reset the master screen control to obtain normal
brightness range.
White Balance Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "V03" and set to "00" (minimum
color)(Record original data code under adjustment
"V03" before changing). "V03" does not have to be
adjusted, if you selected a B/W picture or monoscope
pattern.
3. Alternately adjust the service adjustment data of
"V09" and "V10" until a good grey scale with normal
whites is obtained. (RF Input)
4. For component input, the data value of "V49" and
"V50" is adjusted to follow the data value of "V09"
and "V10" respectively.
5. Select the service adjustment "V03" and reset data
to obtain normal color level.
Sub-picture and Sub-Bright Adjustments
1. Receive the window pattern signal.
• RF INPUT (TU51)
2. Get into service adjustment data "V01" and "V05" and
set the luminance as shown in figure "A" and "B" as
below respectively.
• COMPONENT INPUT
3. Get in service adjustment data "V42" and "V45" and
set the luminance as shown in figure "A" and "B" as
below respectively.
LUMINESCENCE CONFIRMATION
A: 80±10cd/m
B: 1.1±0.5cd/m
2
2
9
Page 10
35UF6
Sub-Tint Adjustment
1. Receive the half color bar signal.
• RF INPUT (TU51)
2. Get into Y-Mute by R/C, or by setting the "V11" bus
data to "01".
3. Vary the "V02" bus data until the waveform becomes
as stated below.
LEVEL
B-AMP Base waveform in step
(TP47B)
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position .
• RF INPUT (TU51)
3. Enter the service mode and select service adjustment
"V03".
4. Adjust "V03" data value to obtain a normal color level.
Focus Adjustment
1. Receive a good local channel.
2. Adjust the FOCUS VR of the flyback transformer to
make the image as fine as possible.
C. C Display Position Adjustment
1. Receive the lion head pattern signal.
2. Select "EX2" to display the text box.
3. Adjust the "EX2" bus data to let the text box displayed
in the center.
DISPLAY OF TEXT BOX
TEXT BOX
| A-B | / 2
Note: Aging for 10 min before adjustment. After the
adjustment of V-center and V-size, readjustment for this V-line.
Vertical Phase Adjustment
(SCREEN FORMAT 4:3)
1. Enter the service mode and input data of “00h” on
"D01".
2. Adjust "D18" data value so that picture is centered.
3. Input data of "00h" on "D20".
4. Input data of "D34" same as "D18" data.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "D02".
3. Adjust "D02" data value so that picture is centered.
4. Input data of "D21" same as "D02" data.
Horizontal-Size Adjustment
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D04" for H-size.
3. Adjust the "D04" bus data to get the proper H-size.
4. Input data of "D23" same as "D04" data.
EW-Parabola
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D07" for EW parabola.
3. Adjust the "D07" bus data to get the proper vertical
straight line for both left and right side.
4. Input data of "D26" to mines 16 step from "D07" data.
A
SPEC INSPECTION:| A-B | / 2
B
<
5mm
=
Vertical-Size and Linearity Adjustments
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D03" for V-size.
3. Adjust the "D03" bus data to get the proper V-size.
4. For V-linearity adjustment, select data bus "D05" and
adjust to get the proper vertical linearity.
5. Input data of "D22" to mines 38 step from "D03” data.
(V-SIZE)
6. Input data of "D24" same as "D05" data. (V-LIN)
EW-Trapezium
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D08" for EW-Trapezium.
3. Adjust the "D08" bus data to get the best position
display.
4. Input data of "D27" same as "D08" data.
10
Page 11
Ë
MTS ADJUSTMENT
MTS Level Adjustment
1. Set the sound volume above 1.
Monoral signal: 400Hz, 100% modulation
2. Confirm "EX4" data is "5Ah".
3. Vary the "M01" bus data until the voltage to pin (39)
of IC3001 to become the value as stated below.
SETTING VOLTAGE
ADJ spec : 490±10mVrms
CHK spec: 490±20mVrms
MTS VCO Adjustment
1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µF, 50V) in between
positive(+) side of C3005 and ground.
4. Enter the service mode and select the service
adjustment "M02"
5. Adjust the data so that the frequency counter reads
62.94 ±0.75kHz.
35UF6
Filter Adjustment
1. Feed the following stereo pilot signal to pin (14) of
IC3001 at C3005 open.
Stereo pilot signal: 9.4kHz, 600mVrms.
2. Enter the service mode and select the service
adjustment "M03".
3. Adjust the data until "OK" appears in position on the
screen. Make sure the "OK" is displayed almost at
the center of the data range.
Separation Adjustment
1. Input "SIGNAL 1" and vary the "M04" bus data to get
the minimun AC voltage to pin (39) of IC3001.
2. Input "SIGNAL 2" and vary the "M05" bus data to get
the minimun AC voltage to pin (39) of IC3001.
SIGNAL 1:
SIGNAL 2: 3kHz, 30% modulation, Lch only, NR-ON
Note: SIGNAL 1 Adj. for widebando
SIGNAL 2 Adj. for spectral
Check the output of the speaker at the maximum
volume as stated below.
Confirmation spec:
ADJ spec: above 25 dB
CHK spec: above 20 dB
300Hz, 30% modulation, Lch only, NR-ON
11
Page 12
35UF6
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
654321
12
Page 13
BLOCK DIAGRAM
H
G
F
35UF6
E
D
C
B
A
654321
13
Page 14
35UF6
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µV B & W or Color
signal.
WAVEFORMS
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
ç
MARK= X-RAY RELATED PARTS.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
14
Page 15
SCHEMATIC DIAGRAM: CRT Unit
H
35UF6
G
F
E
D
(DUNTKA527WEE2)(DUNTKA527WEE2)
708708
7001GEFWY7001GEFWY
VB89AJZ90X+1EVB89AJZ90X+1E
QEARCA009WJZZQEARCA009WJZZ
C
B
A
654321
15
Page 16
35UF6
H
G
F
SCHEMATIC DIAGRAM: MAIN-1 Unit
E
D
C
C782C782C782
1000P1000P1000P
D706D706D706
D710D710D710
1SS133++1SS133++1SS133++
EX0650GEEX0650GEEX0650GE
R714R714R714
3.3K3.3K3.3K
B
A
1
2
3
4
5
6
7
98
10
16
Page 17
35UF6
ISS119ISS119ISS119 ISS119ISS119ISS119
17
17161918151413121110
Page 18
35UF6
H
G
F
SCHEMATIC DIAGRAM: MAIN-2 Unit
E
D
C
B
A
1
2
3
4
5
6
7
98
10
18
Page 19
35UF6
19
17161918151413121110
Page 20
35UF6
H
G
F
SCHEMATIC DIAGRAM: 3-LINE Y/C Unit
E
D
C
B
A
1
2
3
4
5
6
7
98
10
20
Page 21
35UF6
21
17161918151413121110
Page 22
35UF6
H
G
F
SCHEMATIC DIAGRAM: MODULE D/F Unit
E
D
C
B
A
1
2
3
4
5
6
7
98
10
22
Page 23
35UF6
ZA023WJZZZA023WJZZZA023WJZZ
23
ZA022WJZZZA022WJZZZA022WJZZ
17161918151413121110
Page 24
35UF6
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
A
PWB-A: MAIN Unit (Components Side)
654321
24
Page 25
35UF6
H
G
F
E
D
C
B
A
PWB-A: MAIN Unit (Chip Parts Side)
654321
25
Page 26
35UF6
H
G
F
E
D
PWB-B: CRT Unit (Wiring Side)
C
B
A
PWB-C: 3-LINE Y/C Unit (Wiring Side)
PWB-C: 3-LINE Y/C Unit (Chip Parts Side)
654321
26
Page 27
35UF6
H
G
F
PWB-H: DF MODULE Unit (Wiring Side)
E
D
C
B
A
654321
27
Page 28
35UF6
Ref. No. Part No. « Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBE
3. PART NO.4. DESCRIPTION
in USA:Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
« MARK: SPARE PARTS-DELIVERY SECTION
p
Ref. No. Part No. « Description Code
pU V101 VB89AJZ90X+1E X Picture Tube CY
U L703RCILGA048WJZZX Degaussing CoilAR
U QEARCA009WJZZ X Ground-Part AD
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-A DUNTKC290WED5 — MAIN Unit —
PWB-B DUNTKA527WEE2 — CRT Unit —
PWB-C DUNTKB573WEV0 — 3-LINE Y/C Unit —
PWB-H DUNTKB569WEV0 — DF MODULE Unit —
R2. REF. NO.
MARK: X-RAY RELATED PARTS
PICTURE TUBE
PWB-A: DUNTKC290WED5
MAIN UNIT
NOTE:THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDETLY
U TU51VTUVT1T5UF202XTunerAS
INTEGRATED CIRCUITS
IC101VHIPQ050ES1-1+XAD
p U IC201VHITB1253AN-1XAS
U IC361VHIAN5277//-1XAK
U IC501VHITDA8177+-1XAG
U IC701VHITEA1533A-1XAG
U IC702RH-FXA003WJZZXAC
D52RH-EX0676GEZZYXZenerDiode32VAB
D103RH-DX0441CEZZYXDiodeAA
D361VHD1SS133++-1YXDiodeAA
D362VHD1SS133++-1YXDiodeAA
D410RH-EX0611GEZZYXZenerDiode5.1V AB
D411RH-EX0611GEZZYXZenerDiode5.1V AB
D412RH-EX0614GEZZYXZenerDiode5.6V AB
C435VCEA0A1HW105M+ X 150VEL.AA
C436VCKYCY1CF104ZY X 0.116VCeramic AA
C437VCKYCY1CF104ZY X 0.116VCeramic AA
C438VCKYCY1HB103KY X 0.0150VCeramic AA
C439VCEA0A1HW106M+ X 1050VEL.AA
C440VCFYFA1HA224J+X 0.2250VMylarAB
C451VCQYTA2AA104K+ X 0.1uF100VMylarAB
C452VCEA0A1EW336M+ X 3325VEL.AA
C471VCKYCY1HB103KY X 0.0150VCeramic AA
C473VCCCCY1HH331JY X 330p50VCeramic AA
C474VCKYCY1HB103KY X 0.0150VCeramic AA
C475VCKYCY1CF104ZY X 0.116VCeramic AA
C476VCKYCY1HB103KY X 0.0150VCeramic AA
C501VCKYPA2HB102K+ X 1000p500VCeramic AA
C502VCEA0A1VW477M+ X 47035VEL.AC
C504VCEACA1HC474M+ X 0.4750VEL.AB
C505VCEA0A1HW474M+ X 0.4750VEL.AA
C506VCKYCY1HB103KY X 0.0150VCeramic AA
C507VCKYCY1HB103KY X 0.0150VCeramic AA
C510RC-FZ0272CEZZ+X 0.39100VMylarAC
C512VCEA0A1EW476M+ X 4725VEL.AA
C514 VCEA0A1VW107M+ X 100 35V EL. AB
C516VCKYCY1HB472KY X 10035VEL.AA
C517VCKYCY1HF103ZY X 0.01uF 50VCeramic AA
C518VCQYTA2AA473J+X 0.047uF 100VMylarAB
C522VCFYFA1HA334J+X 0.3350VMylarAB
C523VCEA0A1HW105M+ X 150VEL.AA
C601VCEA0A1CW108M+ X 100016VEL.AC
C602VCKYCY1CF104ZY X 0.116VCeramic AA
C603VCEA0A1HW225M+ X 2.250VEL.AA
C604VCKYCY1EB223KY X 0.02225VCeramic AA
C606VCKYPA2HB102K+ X 1000p500VCeramic AA
C607VCKYPA1HB472K+ X 4700p50VCeramic AA
C608RC-KZ0033CEZZX 150p2kVCeramic AB
p U C609VCFPVC3ZA213HX 0.021uF 1500VM.Poly. AD
C611VCEA0A1EW477M+ X 47025VEL.AB
C614VCEA0A1EW108M+ X 100025VEL.AC
C615VCFYSB2EB823JX 0.082uF 250VM.Poly.. AB
C616VCKYPA2HB471K+ X 470p500VCeramic AA
C617VCEA0A1HW474M+ X 0.4750VEL.AA
C622VCKYPA2HB102K+ X 1000p500VCeramic AA
C623VCEA4A2EN106M+ X 10250VEL.AC
C652VCEA0A1HW476M+ X 4750VEL.AB
C653VCEA0A1HW106M+ X 1050VEL.AA
C674VCKYCY1HB391KY X 390p50VCeramic AA
C675VCEA0A1HW106M+ X 1050VEL.AA
C677RC-FZ0377CEZZX 4.750VMylarAE
p U C678VCQPPC2GB563JX 0.056uF 400VMylarAC
C680VCFPVC3ZA822HX 8200p1500VM.Poly. AC
p U C701RC-FZA022WJZZX 0.22AC250V M.Poly. AC
C702RC-KZ0029CEZZ+X 0.01AC250V Ceramic AB
C703RC-KZ0029CEZZ+X 0.01AC250V Ceramic AB
U C705RC-EZ0722CEZZX 820200VEL.AK
U C706RC-KZ0089GEZZAX 1000pAC250V Ceramic AB
U C707RC-KZ0092GEZZAX 3300pAC250V Ceramic AC
U C723RC-EZ0724CEZZX 100160VEL.AD
U C725RC-EZA065WJZZX 330160VEL.AG
C726RC-KZ0226CEZZ+X 560p2kVCeramic AC
C727RC-KZ0226CEZZ+X 560p2kVCeramic AC
C729VCEA0A1HW106M+ X 1050VEL.AA
C730VCEA4A1VN108M+ X 100035VEL.AE
C731RC-EZ0385CEZZ+X 100016VEL.AC
Ref. No. Part No. « Description Code
C732VCKYPA2HB102K+ X 1000p500VCeramic AA
C733VCKYPA2HB102K+ X 1000p500VCeramic AA
C734VCKYPA2HB471K+ X 470p500VCeramic AA
C735 VCKYPA2HB471K+ X 470p 500V Ceramic AA
C736 VCKYCY1HF103ZY X 0.01uF 50V Ceramic AA
C737 VCEA0A1HW226M+ X 22 50V EL. AA
C738 VCFPVC3CA102H X 1000p 1250V M.Poly. AC
C739 RC-EZ0385CEZZ+ X 1000 16V EL. AC
C740 VCEA0A1HW476M+ X 47 50V EL. AB
C741 VCEA4A2AN105M+ X 1 100V EL. AB
C742VCEA0A1HW226M+ X 2250VEL.AA
C743RC-KZ0036CEZZ+X 330p2kVCeramic AC
C744VCKYPA2HB471K+ X 470p500VCeramic AA
C745VCKYPA2HB102K+ X 1000p500VCeramic AA
C746VCKYPA2HB102K+ X 1000p500VCeramic AA
C747VCEA0A1HW475M+ X 4.750VEL.AA
C750VCKYCY1HF103ZY X 0.01uF 50VCeramic AA
C753RC-KZ0036CEZZ+X 330p2kVCeramic AC
C754VCKYPA2HB472K+ X 4700p500VCeramic AB
C755VCEA0A1EW476M+ X 4725VEL.AA
C758VCEA0A1HW475M+ X 4.750VEL.AA
C780 VCEA0A1HW226M+ X 22 50V EL. AA
C781VCFYFA1HA105J+X 150VM-Poly. AC
C782VCKYCY1HB102KY X 1000p50VCeramic AA
C783VCQYTA1HM103J+ X 0.01uF 50VMylarAA
C784VCKYCY1HF103ZY X 0.01uF 50VCeramic AA
C801VCCCCY1HH110JY X 11pF50VCeramic AA
C802VCKYCY1HB222KY X 2200p50VCeramic AA
C803VCEA0A1HW224M+ X 0.2250VEL.AA
C804VCKYCY1CF104ZY X 0.116VCeramic AA
C805VCEA0A0JW108M+ X 10006.3VEL.AB
C806VCKYCY1CF104ZY X 0.116VCeramic AA
C807VCKYCY1CF104ZY X 0.116VCeramic AA
C808VCKYCY1CF104ZY X 0.116VCeramic AA
C809VCKYCY1CF104ZY X 0.116VCeramic AA
C810VCEA0A1CW477M+ X 47016VEL.AB
C812VCQYTA1HM104J+ X 0.1uF50VMylarAB
C901VCKYCY1HB103KY X 0.0150VCeramic AA
C902VCKYCY1HB103KY X 0.0150VCeramic AA
C903VCKYCY1HB681KY X 680p50VCeramic AA
C904VCEA0A1HW105M+ X 150VEL.AA
C905VCEA0A1HW105M+ X 150VEL.AA
C906VCKYCY1HB681KY X 680p50VCeramic AA
C907VCEA0A1HW105M+ X 150VEL.AA
C908VCKYCY1HB103KY X 0.0150VCeramic AA
C909VCEA0A1HW105M+ X 150VEL.AA
C910VCEA0A1HW105M+ X 150VEL.AA
C911VCEA0A1HW105M+ X 150VEL.AA
C912VCEA0A1HW105M+ X 150VEL.AA
C913VCEA0A1HW105M+ X 150VEL.AA
C914VCKYCY1HB681KY X 680p50VCeramic AA
C915VCKYPA1HF103Z+X 0.01uF 50VCeramic AA
C916VCKYCY1HB103KY X 0.0150VCeramic AA
C917VCEA0A1HW105M+ X 150VEL.AA
C918VCKYCY1HB681KY X 680p50VCeramic AA
C919VCEA0A1HW105M+ X 150VEL.AA
C920VCEA0A1HW105M+ X 150VEL.AA
C921VCKYCY1HB681KY X 680p50VCeramic AA
C922VCKYCY1CF104ZY X 0.116VCeramic AA
C923VCEA0A1CW107M+ X 10016VEL.AA
C926VCEA0A1EW476M+ X 4725VEL.AA
C928VCEA0A1HW105M+ X 150VEL.AA
C930VCEA0A1HW475M+ X 4.750VEL.AA
C931VCKYCY1HB183KY X 0.01850VCeramic AA
C932VCKYCY1HB183KY X 0.01850VCeramic AA
C933VCEA0A1HW475M+ X 4.750VEL.AA
C934VCEA0A1EW476M+ X 4725VEL.AA
C935VCEA0A1HW475M+ X 4.750VEL.AA
C936VCEA0A1HW475M+ X 4.750VEL.AA
C937 VCKYCY1HB103KY X 0.01 50V Ceramic AA
C953VCKYCY1HB681KY X 680p50VCeramic AA
C956VCEA0A1CW477M+ X 47016VEL.AB
C1434 VCEA0A1EW476M+ X 4725VEL.AA
C1437 VCEA0A1EW476M+ X 4725VEL.AA
C2001 VCCCCY1HH101JY X 100p50VCeramic AA
C2002 VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C2025 VCCCCY1HH101JY X 100p50VCeramic AA
C2040 VCKYCY1CF104ZYX 0.116VCeramic AA
C2041 VCEA0A1HW105M+ X 150VEL.AA
C2043 VCCCCY1HH331JY X 330p50VCeramic AA
C2044 VCCCCY1HH100DY X 10p50VCeramic AA
C2046 VCEA0A1EW476M+ X 4725VEL.AA
C2047 VCKYCY1CB473KY X 0.04716VCeramic AA
C2060 VCKYCY1CF104ZYX 0.116VCeramic AA
C2061 VCCCCY1HH101JY X 100p50VCeramic AA
C2062 VCEA0A1CW107M+ X 10016VEL.AA
C2063 VCKYCY1CF104ZYX 0.116VCeramic AA
C2064 VCKYCY1CF104ZY X 0.1 16V Ceramic AA
C2201 VCKYCY1HB681KY X 680p50VCeramic AA
C2202 VCCCCY1HH330JY X 33p50VCeramic AA
C2601 VCEA0A1EW476M+ X 4725VEL.AA
C2602 VCCCCY1HH101JY X 100p50VCeramic AA
C3001 VCEA0A1HW475M+ X 4.750VEL.AA
C3002 VCKYCY1HB562KY X 5600p50VCeramic AA
C3003 VCKYCY1EB123KY X 0.01225VCeramic AA
C3004 VCEA0A1HW105M+ X 150VEL.AA
C3005 VCEA0A1HW475M+ X 4.750VEL.AA
C3006 VCEA0A1HW106M+ X 1050VEL.AA
C3007 VCEA0A1HW475M+ X 4.750VEL.AA
C3008 VCKYCY1CF104ZYX 0.116VCeramic AA
C3009 VCEA0A1CW477M+ X 47016VEL.AB
C3010 VCE9GA1HW475M+ X 4.750VEL.AB
C3011 VCEA0A1HW475M+ X 4.750VEL.AA
C3012 VCEA0A1HW475M+ X 4.750VEL.AA
C3013 VCKYCY1HB272KY X 2700p50VCeramic AA
C3014 VCKYCY1CB473KY X 0.04716VCeramic AA
C3015 VCEACA1HC335K+ X 3.350VEL.AC
C3016 VCE9GA1HW475M+ X 4.750VEL.AB
C3017 VCEACA1CC106K+ X 1016VEL.AC
C3018 VCEA0A1HW105M+ X 150VEL.AA
C3021 VCEA0A1HW475M+ X 4.750VEL.AA
C3022 VCEA0A1HW475M+ X 4.750VEL.AA
C3025 VCKYCY1CB473KY X 0.04716VCeramic AA
C3027 VCKYCY1CB473KY X 0.04716VCeramic AA
C3028 VCKYCY1HB682KY X 6800p50VCeramic AA
C3029 VCKYCY1HB682KY X 6800p50VCeramic AA
R502VRN-RA2BK822FYX 8.2k1/8WM-Film AA
R503VRS-CY1JF105JYX 1M1/16WM-Ox.AA
R504VRS-CY1JF154JYX 150k1/16WM-Ox.AA
R505VRS-CY1JF101JYX 1001/16WM-Ox.AA
R510VRN-RA2BK103FYX 10k1/8WM-Film AA
R511VRN-RA2BK222FYX 2.2k1/8WM-Film AA
R512VRN-RA2BK272FYX 2.7k1/8WM-Film AA
R513VRD-RM2HD1R5JY X 1.51/2WCarbon AA
R517VRS-CY1JF104JYX 100k1/16WM-Ox.AA
R518VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R521VRS-CY1JF101JYX 1001/16WM-Ox.AA
U R523VRN-RL3DBR82J+X 0.822WM-Film AB
U R524VRS-RG3AB561J+X 5601WM-Ox.AB
R601VRS-CY1JF101JYX 1001/16WM-Ox.AA
R603VRD-RA2BE472JYX 4.7k1/8WCarbon AA
U R604VRS-KA3NG272JX 2.7k7WM-Ox.AD
R605VRD-RM2HD331JYX 3301/2WCarbon AA
R606VRD-RM2HD331JYX 3301/2WCarbon AA
U R621VRN-RL3AB3R3J+X 3.31WM-Film AB
U R622VRN-RL3ABR47J+X 0.471WM-Film AB
U R623VRN-RL3AB4R7J+X 4.71WM-Film AB
U R624VRS-RG3DB332J+X 3.3k2WM-Ox.AB
U R627VRN-RL3ABR47J+X 0.471WM-Film AB
U R628VRN-RL3ABR47J+X 0.471WM-Film AB
p U R651VRS-RG2HC270J+X 271/2WM-Ox.AB
p U R652VRD-RA2EE103GYX 10k1/4WCarbon AA
p U R653VRD-RA2EE562GYX 5.6k1/4WCarbon AA
p U R654VRD-RA2BE563JYX 56k1/8WCarbon AA
U R658VRS-RG3DB183J+X 18k2WM-Ox.AB
R663VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R670VRS-CY1JF000JYX 001/16WM-Ox.AA
R684VRD-RA2BE472JYX 4.7k1/8WCarbon AA
R685VRD-RA2BE822JYX 8.2k1/8WCarbon AA
R686VRD-RA2EE332JYX 3.3k1/4WCarbon AA
R687VRD-RA2BE103JYX 10k1/8WCarbon AA
U R688VRN-RL3DB3R3J+X 3.32WM-Film AB
R689VRD-RM2HD824JYX 820k1/2WCarbon AA
R695VRS-CY1JF683JYX 68k1/16WM-Ox.AA
U R701RR-DZ0049CEZZYX 3.9M1/2WSolidAB
U R703VRW-KQ4AC1R2KX 1.210WCement AC
U R705VRN-RL3DBR15J+X 0.152WM-Film AB
U R706VRN-RL3DBR15J+X 0.152WM-Film AB
R707VRD-RM2HD270JYX 271/2WCarbon AA
R708VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R709VRS-CY1JF393JYX 39k1/16WM-Ox.AA
U R710VRS-RG2HC103J+X 10k1/2WM-Ox.AB
R711VRS-CY1JF334JYX 330k1/16WM-Ox.AA
R712VRD-RM2HD100JYX 101/2WCarbon AA
U R713VRS-RG2HC152J+X 1.5k1/2WM-Ox.AB
R714VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R715VRN-RL2HCR56J+X 0.561/2WM-Film AB
R716VRD-RM2HD100JYX 101/2WCarbon AA
R720VRD-RA2BE473JYX 47k1/8WCarbon AA
R724VRD-RM2HD101JYX 1001/2WCarbon AA
R725VRD-RM2HD821JYX 8201/2WCarbon AA
R734VRD-RM2HD124JYX 120k1/2WCarbon AA
U R737VRN-RL3LBR82J+X 0.823.0WM-Film AC
R742VRD-RA2BE222JYX 2.2k1/8WCarbon AA
R743VRD-RM2HD470JYX 471/2WCarbon AA
R744VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R745VRD-RA2BE683JYX 68k1/8WCarbon AA
R750VRS-CY1JF224JYX 220k1/16WM-Ox.AA
R751VRD-RA2BE473JYX 47k1/8WCarbon AA
R752VRD-RA2BE392JYX 3.9k1/8WCarbon AA
R753VRS-CY1JF223JYX 22k1/16WM-Ox.AA
R754VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R755VRS-CY1JF473JYX 47k1/16WM-Ox.AA
R756VRD-RA2BE152JYX 1.5k1/8WCarbon AA
U R757VRN-RL3DB4R7J+X 4.72WM-Film AB
R759VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R761VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R762VRD-RA2EE151JYX 1501/4WCarbon AA
R764VRD-RM2HD562JYX 5.6k1/2WCarbon AA
R767VRD-RM2HD151JYX 1501/2WCarbon AA
R768VRD-RA2BE393JYX 39k1/8WCarbon AA
R775VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R776VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R801VRS-CY1JF333JYX 33k1/16WM-Ox.AA
R802VRS-CY1JF471JYX 4701/16WM-Ox.AA
R803VRS-CY1JF000JYX 001/16WM-Ox.AA
R805VRS-CY1JF682JYX 6.8k1/16WM-Ox.AA
R806VRS-CY1JF681JYX 6801/16WM-Ox.AA
R807VRS-CY1JF681JYX 6801/16WM-Ox.AA
R808VRS-CY1JF681JYX 6801/16WM-Ox.AA
R810VRS-CY1JF472JYX 4.7k1/16WM-Ox.AA
R903VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R904VRS-CY1JF683JYX 68k1/16WM-Ox.AA
R2606 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R3001VRS-CY1JF221JYX 2201/16W M-Ox. AA
R3002VRS-CY1JF221JYX 2201/16W M-Ox. AA
R3003VRS-CY1JF105JYX 1M1/16W M-Ox. AA
R3004VRS-CY1JF104JYX 100k1/16W M-Ox. AA
R3005VRS-CY1JF623JYX 62k1/16W M-Ox. AA
R3007VRS-CY1JF332JYX 3.3k1/16W M-Ox. AA
R3008VRS-CY1JF302JYX 3k1/16W M-Ox. AA
R3010VRS-CY1JF392JYX 3.9k1/16W M-Ox. AA
R3017VRS-CY1JF102JYX 1k1/16W M-Ox. AA
R3018VRS-CY1JF102JYX 1k1/16W M-Ox. AA
R3019VRS-CY1JF101JYX 1001/16W M-Ox. AA
R3024VRD-RA2BE102JYX 1k1/8WCarbon AA
C850VCFYSB2EB224KX0.22uF 250VM.Poly. AB
C851RC-KZ018JCEZZX 0.01AC250V Ceramic AB
C852VCEA0A1CW107M+ X 10016VEL.AA
C853VCFYFA1HA224J+X0.2250VMylarAB
C854VCEA0A1CW227M+ X 22016VEL.AB
C855VCEA0A2EW336M+ X33250VEL.AD
C856VCEA0A1HW106M+ X 1050VEL.AA
C1501VCEA0A1CW476M+ X 4716VEL.AA
C1506VCKYPA1HF103Z+X0.01uF 50VCeramic AA
C1508VCKYPA2HB472K+X4700p500VCeramic AB
C1509VCKYPA1HB472K+X4700p50VCeramic AA
C1510VCKYPA1HF103Z+X0.01uF 50VCeramic AA
C1511VCKYPA1HF103Z+X0.01uF 50VCeramic AA
C1515VCEA0A1HW476M+ X 4750VEL.AB
C1516VCEA0A1HW476M+ X 4750VEL.AB
C1517VCEA0A2AW106M+ X10100VEL.AB
C1518VCCSPA2HL560K+X56p500VCeramic AB
C1519VCEA0A2CW106M+ X 10160VEL.AB
RESISTORS
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
U R850VRS-SV2HC152JX 1.5k1/2WM-Ox.AA
U R851VRS-SV2HC152JX 1.5k1/2WM-Ox.AA
U R852VRS-SV2HC152JX 1.5k1/2WM-Ox.AA
U R853VRS-SV2HC272JX 2.7k1/2WM-Ox.AA
U R854VRS-SV2HC272JX 2.7k1/2WM-Ox.AA
U R855VRS-SV2HC272JX 2.7k1/2WM-Ox.AA
R856VRD-RM2HD104JYX100k1/2WCarbon AA
R857VRD-RM2HD104JYX100k1/2WCarbon AA
R858VRD-RM2HD104JYX100k1/2WCarbon AA
R862VRC-MA2HG152KY X 1.5k1/2WSolidAB
R863VRC-MA2HG152KY X 1.5k1/2WSolidAB
R864VRC-MA2HG152KY X 1.5k1/2WSolidAB
U R867VRS-SV2HC392JX 3.9k1/2WM-Ox.AA
U R868VRS-SV2HC682JX 6.8k1/2WM-Ox.AA
R869VRD-RA2BE103JYX 10k1/8WCarbon AA
R870VRD-RA2BE223JYX 22k1/8WCarbon AA
R871VRD-RA2BE472JYX 4.7k1/8WCarbon AA
R872VRD-RA2EE680JYX 681/4WCarbon AA
R873VRD-RM2HD224JYX220k1/2WCarbon AA
R874VRD-RM2HD104JYX100k1/2WCarbon AA
34
Page 35
35UF6
Ref. No. Part No. « Description Code
PWB-B: DUNTKA527WEE2
CRT UNIT
RESISTORS
R875 VRD-RM2HD104JY X 100k 1/2W Carbon AA
R876 VRD-RM2HD104JY X 100k 1/2W Carbon AA
R877 VRD-RA2BE103JY X 10k 1/8W Carbon AA
R878 VRS-SV2HC120J X 12 1/2W M-Ox. AA
U
R1511 VRD-RA2BE101JY X 100 1/8W Carbon AA
R1513 VRS-VV3DB561J X 560 2W M-Ox. AA
U
R1514 VRD-RA2BE100JY X 10 1/8W Carbon AA
R1515 VRD-RA2BE820JY X 82 1/8W Carbon AA
R1516 VRD-RA2BE820JY X 82 1/8W Carbon AA
R1517 VRD-RA2BE122JY X 1.2k 1/8W Carbon AA
R1518 VRD-RA2BE683JY X 68k 1/8W Carbon AA
R1519 VRD-RA2BE123JY X 12k 1/8W Carbon AA
R1520 VRD-RA2BE683JY X 68k 1/8W Carbon AA
R1521 VRD-RA2BE122JY X 1.2k 1/8W Carbon AA
R1525 VRD-RA2EE560JY X 56 1/4W Carbon AA
R1526 VRD-RA2EE560JY X 56 1/4W Carbon AA
R1527 VRD-RM2HD1R5JY X 1.5 1/2W Carbon AA
R1528 VRD-RM2HD1R5JY X 1.5 1/2W Carbon AA
R1529 VRS-VV3DB221J X 220 2W M-Ox. AA
U
R1530 VRD-RA2BE122JY X 1.2k 1/8W Carbon AA
FB1501 RBLN-0020CEZZ+ X Ferrite Bead AB
P854 QPLGN0741CEZZ X plug (7 PINS) AB
U
P860 QPLGN0841CEZZ X plug (8 PINS) AB
P861 QPLGN0241CEZZ X plug (2 PINS) AA
SC850 QSOCV0936CEZZ X Socket,12Pin AG
RDA850 PRDAR0248PEFW X Heat Sink AD
RDA1506 PRDAR5072CEFW X Heat Sink AC
RDA1507 PRDAR5072CEFW X Heat Sink AC
C1412 VCEA0A1HW106M+ X 10 50V EL. AA
C1413 VCKYCY1HF103ZY X 0.01uF 50V Ceramic AA
C1414 VCCCCY1HH3R0CY X 3p 50V Ceramic AA
C1415 VCE9GA1CW106M+ X 10 16V EL. AB
C1416 VCEA0A1CW477M+ X 470 16V EL. AB
C1417 VCKYCY1CF104ZY X 0.1 16V Ceramic AA
C1420 VCCCCY1HH270JY X 27p 50V Ceramic AA
C1421 VCCCCY1HH120JY X 12pF 50V Ceramic AA
INTEGRATED CIRCUITS
TRANSISTORS
FILTERS
CAPACITORS
Ref. No. Part No. « Description Code
C1422VCCCCY1HH120JYX 12pF50VCeramic AA
C1423VCCCCY1HH3R0CY X 3p50VCeramic AA
C1424VCCCCY1HH270JYX 27p50VCeramic AA
C1425VCCCCY1HH100DYX 10p50VCeramic AA
C1428VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1435VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1436VCKYCY1CF104ZYX 0.116VCeramic AA
C1439VCE9GA1CW106M+ X 1016VEL.AB
C1440VCEA0A1HW106M+X 1050VEL.AA
C1441VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1442VCFYFA1HA474J+X 0.4750VMylarAB
C1443VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1444VCKYCY1HB472KYX 10035VEL.AA
C1445 VCKYCY1HF103ZY X 0.01uF 50V Ceramic AA
C1446VCCCCY1HH181JYX 180p50VCeramic AA
C1447VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1448VCKYCY1CF104ZYX 0.116VCeramic AA
C1449VCKYCY1CF104ZYX 0.116VCeramic AA
C1451VCEA0A1CW107M+X 10016VEL.AA
C1452VCKYCY1CF104ZYX 0.116VCeramic AA
C1453VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1454VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1455VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1456VCKYCY1CF104ZYX 0.116VCeramic AA
C1457VCEA0A1HW106M+X 1050VEL.AA
C1458VCEA0A1HW106M+X 1050VEL.AA
C1460VCKYCY1HF103ZYX 0.01uF 50VCeramic AA
C1470VCCCCY1HH270JYX 27p50VCeramic AA
C1474VCCCCY1HH150JYX 15p50VCeramic AA
C1610VCFYSB2EB224KX 0.22uF 250V M.Poly. AB
C1644VCFPFA2EB684JX 0.68uF 250V EL.AC
C1677VCKYPA1HB391K+X 390p50VCeramic AA
C1678VCKYPA1HB391K+X 390p50VCeramic AA
C1681RC-KZ0024CEZZX 1000p 2kVM.Poly. AC
C1682RC-KZ0037CEZZX 390p2kVM.Poly. AB
C1683VCE9GA1HW335M+ X 3.350VEL.AB
C1684VCEA0A1VW477M+X 47035VEL.AC
C1685VCFYFA1HA474J+X 0.4750VMylarAB
C1686VCEA0A1VW108M+X 100035VEL.AC
C1687VCEA0A1EW107M+X 10025VEL.AB
C1695VCFYFA1HA224J+X 0.2250VMylarAB
C1696 VCQYTA1HM103J+ X 0.01uF 50V Mylar AA
RESISTORS
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
R1610VRS-VV3DB103JX 10k2WM-Ox.AB
R1627VRS-KT3LB122JX 1.2k3WM-Ox.AD
R1656VRD-RA2BE394JYX 390k1/8W Carbon AA
R1657VRD-RA2BE683JYX 68k1/8W Carbon AA
R1658VRD-RA2BE183JYX 18k1/8W Carbon AA
R1659VRD-RA2BE102JYX 1k1/8W Carbon AA
R1680VRS-KT3LB154JX 150k3WM-Ox.AD
R1681VRS-KT3LB104JX 100k3WM-Ox.AD
R1682VRC-MA2HG333KYX 33k1/2W SolidAB
R1683VRD-RA2BE332JYX 3.3k1/8W Carbon AA
R1684VRD-RA2BE681JYX 1.5k1/8W Carbon AA
R1685VRS-VV3AB181JX 1801WM-Ox.AB
R1686VRD-RA2BE103JYX 10k1/8W Carbon AA
R1687VRD-RA2BE103JYX 10k1/8W Carbon AA
R1688VRD-RA2BE473JYX 47k1/8W Carbon AA
R1689VRD-RA2BE823JYX 82k1/8W Carbon AA
R1690VRD-RA2BE822JYX 8.2k1/8W Carbon AA
R1691VRD-RA2BE823JYX 82k1/8W Carbon AA
R1695VRD-RA2BE224JYX 220k1/8W M-Ox.AA
R1696VRD-RA2BE684JYX 680k1/8W Carbon AA
R1697VRD-RA2EE1R0JYX 11/4W Carbon AA
R1698VRD-RA2BE472JYX 4.7k1/8W Carbon AA
R1699VRD-RA2BE562JYX 5.6k1/8W Carbon AA
SP1 VSP1206PB648A X Speaker (L) AK
SP2 VSP1206PB648A X Speaker (R ) AK
QCNW-A689WJZZ X WIRE (SPEAKER) AE
QCNW-B177WJZZ X WIRE (XA) AD
QCNW-B178WJZZ X WIRE (XB) AG
QCNW-B179WJZZ X WIRE (XC) AE
QCNW-B294WJZZ X WIRE (CJ) AE
QCNW-B295WJZZ X WIRE (N) AE
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
QRC0023-U
June. 2004
Modify : SEMEX
Design and Production Information
Design base : JAPAN
Production : SEMEX
J B
SHARP ELECTRONICA MEXICO S. A. DE C. V.
Quality & Reliability Control Center
Blvd. SHARP No. 3510 Parque Industrial Rosarito
Playas de Rosarito, México B. C. 22710
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.