SHARP 27N-S100, 27N-S180, CN27S10, CN27S14, CN27S18 Diagram

Page 1
27N-S100, 27N-S180 CN27S10/14/18
SERVICE MANUAL
S40Z327N-S100
COLOR TELEVISION
Chassis No. SN-91
27N-S100, 27N-S180
MODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
CN27S10, CN27S14, CN27S18
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS .........................................................................................................1
» LOCATION OF USER'S CONTROL .....................................................................................................6
» INSTALLATION AND SERVICE INSTRUCTIONS................................................................................7
» CHASSIS LAYOUT .............................................................................................................................13
» BLOCK DIAGRAM ..............................................................................................................................14
» SCHEMATIC DIAGRAMS ...................................................................................................................18
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................38
» REPLACEMENT PARTS LIST............................................................................................................42
» PACKING OF THE SET ......................................................................................................................51
ELECTRICAL SPECIFICATIONS
POWER INPUT.................................................... 120 V AC 60 Hz
POWER RATING ..................................................................110 W
PICTURE SIZE ........................................... 2,187cm2 (339sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING .............. 1.3W + 1.3W (at 10% distortion and
Dual CH Operate)
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF.....................................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels...............................................................2 thru 13
UHF-Channels ............................................................14 thru 69
CATV Channels...........................................................1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without prior notice.
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
1
Page 2
27N-S100, 27N-S180 CN27S10/14/18
Service work should be performed only by qualified service technicians who are throughly familiar with all safety checks and the servicing guidelines which follow:
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems which are separated by insulating material. The non­isolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A­125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE
When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the pic­ture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion protection.
2. Replace with tube of the same type number for continued safety .
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that X­radiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified.
2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically.
3. High voltage should always be kept at the rated value
no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly.
5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry.
6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.
2
Page 3
2 2
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
27N-S100, 27N-S180 CN27S10/14/18
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)
Before returning the receiver to the user, perform the following safety checks.
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner.
Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test).
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.
Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a non­polarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.
AC
VOLTMETER
1.5k ohm 10W
0.15µF
TEST PROBE
TO EXPOSED METAL PARTS
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
CONNECT TO KNOWN EARTH GROUND
SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
3
Page 4
27N-S100, 27N-S180 CN27S10/14/18
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit. C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs peuvent présenter un danger de choc électrique lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur possède deux systèmes de masse qui sont séparées par du matériel d'isolation. Le système de masse non-isolée (sous tension) est pour le circuit du régulateur de tension B+ et le circuit de sortie horizontale. Le système de masse isolée est pour les tensions DC B+ basses et le circuit secondaire du transformateur haute tension. Pour éviter tout risque d'électrocution lors de l'entretien de ce châssis, utiliser un transformateur d'isolation entre le cordon de ligne et la prise de courant.
PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES
4A 125V
D'INCENDIE, REMPLACER LE FUSIBLE P AR UN FUSIBLE DE MEME TYPE 4A-125V .
REP ARA TION DU SYSTEME A HAUTE TEN­SION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme, supprimer la charge statique en branchant une résistance de 10 k en série avec un fil isolé (comme une sonde d'essai) entre la mise à la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit être retiré de la prise murale.)
1. Le tube image dans ce récepteur emploie une protection intégrée contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'après avoir déchargé totalement la haute tension.
LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION
1. Tout le personnel réparateur doit être instruit des instructions et procédés relatifs aux radiations X. Le tube-image, seule source de rayons X dons les téleviseurs transistorisés, n'émet pourtant pas de rayons mesurables si la haute tension est maintenue à un niveau préconisé dans la section "Vérification de la haute tension". C'est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l'enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension en-dessous du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un voltmètre à haute tension qui doit être périodiquement étalonné.
3. La haute tension doit toujours être maintenue à la valeur de régime -et pas plus haute. L'opération à des tensions plus élevées peut entraîner une panne du tube-image ou du circuit à haute tension et, dans certaines conditions, peut entraîner une radiation dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne correctement, il n'y a aucun problème de radiation X. Chaque fois qu'un châssis couleurs est réparé, la luminosité doit être examinée bout en contrôlant la haute tension à l'aide d'un voltmètre pour s'assurer que la haute tension ne dépasse pas la valeur spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié et ne pas effectuer de modifications déconseillées du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures d'essai sur un récepteur qui présente une haute tension excessive, éviter de s'approcher inutilement du récepteur. Ne pas faire fonctionner le récepteur plus longtemps que nécessaire pour localiser la cause de la tension excessive.
4
Page 5
27N-S100, 27N-S180
2 2
CN27S10/14/18
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur , effectuer les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1,5 k 10 watts en parallèle avec un condensateur de 0,15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre.
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000/V pour mesurer la chute de tension en travers de la résistance.
T oucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0,5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client.
Voltmètre CA
1.5k ohm 10W
0.15µF
SONDE D'ESSAI
AUX PIECES METALLIQUES EXPOSEES
TO EXPOSED
METAL PARTS
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
BRANCHER A UNE TERRE CONNUE
CONNECT TO KNOWN EARTH GROUND
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les téléviseurs présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
identifiées par la marque " å " et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas les mêmes caractéristiques que les pièces recommandées par l'usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.
5
Page 6
27N-S100, 27N-S180 CN27S10/14/18
LOCATION OF USER'S CONTROL
Front Panel
POWER
Press On. Press again Off.
VOLUME UP/DOWN
(+) Increases sound. (–) Decreases sound.
Basic Remote Control Functions
POWER
Press On. Press again Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons, you can program your favorite programs by using the four categories A, B, C and D. The channels can be accessed quickly by using these buttons.
VOLUME UP/DOWN
(+) Increases sound. (–) Decreases sound.
• In menu mode, changes or selects the TV adjustments.
MENU
Press Accesses MAIN MENU. Press again → Exits MAIN MENU.
TV-CATV MODE SELECT SWITCH
In TV position, sends power and channel select commands (Channel up/down and Random Access buttons) to the TV. In CATV position, sends power and channel select commands to a cable TV converter.
VCR CONTROL
SENSOR AREA FOR REMOTE CONTROL
+
VIDEO/AUDIO TERMINALS
(VIDEO/AUDIO terminals are also
provided on the rear.)
CHANNEL UP/DOWN
'
( ) Selects next higher channel. ( ) Selects next lower channel.
"
• Press both at same time to access MAIN MENU Screen.
Infrared Transmitter Window
DISPLAY
Press Displa ys receiving channel for four seconds. Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption mode.
INPUT
Press Switch to external video INPUT 1 mode. Press again Switch to external video INPUT 2 mode. Press three times Switch back to the original TV mode.
ENTER
Used in some instances where a VCR or Cable Converter Box requires an “enter” command after selecting channels, when using the REMOTE KEYPAD button.
CHANNEL UP/DOWN
( ) Selects next higher channel.
'
( ) Selects next lower channel.
"
• Moves the “
screens.
MUTE
Press Mutes sound. Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
IN 2
” mark of the MENU
NOTE:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunlight and fluorescent lighting are the most effective when charging the display.
6
Page 7
27N-S100, 27N-S180 CN27S10/14/18
INSTALLATION AND SERVICE INSTRUCTIONS
Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2)Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate input voltage.
2. Allow for warm up and adjust all customer controls for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 11.2 ± 0.6V.
5. Apply external 13.8V DC at TP653 by using an external DC supply, TV must shut off.
6. To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.
HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:
1. Connect an accurate high voltage meter between ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC line voltage, with a strong air signal or a properly tuned in test signal.
3. Enter the service mode and select the service adjustment "S19" and Bus data "01" (Y-mute on).
4. The voltage should be approximately, 28.7kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.
7
Page 8
27N-S100, 27N-S180 CN27S10/14/18
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if serv­ice adjustments are required.
1. Service mode
Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset function in the video adjustment menu to ensure customer controls are in their proper (reset) position.
2. Service number selection
Once in the service mode, press the Ch-up or Ch­down button on the remote controller or at the set. The service adjustment number will vary in increments of one, from "S01" to "M05". Select the item you wish to adjust.
3. Data number selection
Press the Vol-up or down button to adjust the data number.
DATA NUMBER
SERVICE ADJUSTMENT NUMBER
To enter the service mode and exit serv­ice mode.
While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket. Now the TV set is switched on and enters the service mode. To exit the service mode, turn the television off by pressing the power button.
CHANNEL
S01
Figure A.
55(085)
02
S01 D:00
8
Page 9
27N-S100, 27N-S180 CN27S10/14/18
SERVICE
NUMBER
S01 PICTURE 55 00-7F S02 TINT 46 00-7F S03 COLOR 32 00-7F S04 BRIGHTNESS 40 00-7F S05 SHARPNESS 28 00-3F Must be set to "28" S06 VERTICAL PHASE 00 00-07 Must be set to "00" S07 HORIZONT AL PHASE 12 00-1F S08 RF-AGC 23 00-3F S09 VERTICAL AMP 20 00-3F S10 PIF VCO 2C 00-7F S11 R CUT-OFF 00 00-FF S12 G CUT -OFF 00 00-FF S13 B CUT-OFF 00 00-FF S14 G GAIN 7F 00-FF S15 B GAIN 7F 00-FF S16 TRAP 00 00 or 01 Must be set to "00" S17 BALANCE 20 00-3F Must be set to "20" S18 C.C.POSITION 17 00-7F S19 MUTE 00 00,01,03 "00"=Normal, "01"=No-Y, "03"=No Vertical S20 ENERGY SAVE OFFSET 20 00-3F Must be set to "23" S21 D.D.E. OFFSET 03 00-1F Must be set to "03" S22 OSD SETUP 00 00-03 Must be set to "00" S23 TUNER SETUP 00 00, 01 Must be set to "00" OP1 OPTION1 (Set to each mode) 00 00-FF "B3"=27N-S100, "B7"=27N-S180,
OP2 OPTION2 00 00-FF "A7"=27N-S100, "A7"=27N-S180, M01 INPUT LEVEL 0A 00-0F
M02 ST VCO 20 00-3F M03 FILTER 1C 00-3F M04 WIDE BAND 20 00-3F M05 SPECTRAL 1B 00-3F
ADJUSTMENT ITEM
INITIAL VALUE
DATA
ADJUSTMENT CONTENTS
RANGE
"A7"=CN27S10, "A7"=CN27S14, "A7"=CN27S18 "07"=CN27S10, "A7"=CN27S14, "A7"=CN27S18
Table - A
Holding down both the Vol-up/CH-down buttons on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2101.
PART REPLACED
NECESSARY
IC2001
IC201 X
IC2101
CRT IC3001
ADJUSTMENT
X
X X
UNNECESSARY
X
Data is stored in IC2101. The adjustment is needed to compensate for characteristics
of parts including IC201 and MTS level (M01).
Holding down both the Vol-up/CH-down buttons on the TV set in the service mode for more than 2 seconds will automatically write the above initial values into IC2101. Then perform a complete adjustment.
Adjust items related to picture tube only. Adjust items related to MTS only (M01~M05).
NOTES
Table - B
9
Page 10
27N-S100, 27N-S180 CN27S10/14/18
SERVICE ADJUSTMENT
VCO Adjustment
1. Connect a digital voltmeter between pin (44) of IC201 and ground.
2. Receive a good local channel.
3. Enter the service mode and select the service adjustment "S10".
4. Adjust the data so that digital voltmeter reads 2.2V.
5. Adjustment is completed, remove the voltmeter, return to "normal" mode.
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S08".
3. Set the data value to point where no noise or beat appears.
4. Select another channel to confirm that no noise or beat appears. Note 1 : You will have to come out of the service
mode to select another channel.
Note 2 : Setting the data to "00" will produce a black
raster.
White Balance Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S03" and set to "00" (minimum color)(Record original data code under adjustment "S03" before changing). "S03" does not have to be adjusted, if you selected a B/W picture or monoscope pattern.
3. Alternately adjust the service adjustment data of "S14" and "S15" until a good grey scale with normal whites is obtained.
4. Select the service adjustment "S03" and adjust data to obtain normal color level.
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to maximum.
3. Enter the service mode and select the service adjustment "S01".
4. Adjust the data value to achieve normal contrast range.
Screen Adjustment
1. Connect a oscilloscope between TP854 and GND on the CRT Unit.
2. Receive a good local channel.
3. Enter the service mode and select the service adjustment "S03" and set the data value to "00" to set the color level to minimum. (Record original data code under adjustment "S03" before changing) You may skip this step, if you selected a B/W picture or monoscope pattern.
4. Select the service adjustment "S19" and adjust the data value to "01", this turn off the luminance signal (Y-mute).
5. Select the service adjustment "S04" and adjust data value to obtain 2.35 volts on the oscilloscope screen.
6. Adjust the master screen control until the raster darkens to the point where raster is barely seen.
7. Adjust the service adjustments "S11" red, "S12" green and "S13" blue to obtain a good grey scale with normal whites at low brightness level.
8. Select the service adjustment "S19" and reset data to "00". Select the service adjustment "S03" and reset data to obtain normal color level.
9. Remove oscilloscope, and reset the master screen control to obtain normal brightness range.
Sub-Tint Adjustment
1. Receive a good local channel.
2. Set customer tint control to center of it's range.
3. Enter the service mode and select the service adjustment "S02".
4. Adjust "S02" data value to obtain normal flesh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center position .
3. Enter the service mode and select service adjustment "S03".
4. Adjust "S03" data value to obtain normal color level.
10
Page 11
27N-S100, 27N-S180 CN27S10/14/18
Sub-Brightness Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to center position.
3. Enter the service mode and select the service adjustment "S04".
4. Adjust "S04" data value to obtain normal brightness level.
Vertical-Size Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S09".
3. While observing the top and bottom of the screen, adjust "S09" data value to proper vertical size.
Vertical Phase Adjustment
1. Enter the service mode and select the service adjustment "S06".
2. Adjust data value to "00".
Note: This must be set "00" when changed data retrace
line will appear.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S07".
3. Adjust "S07" data value so that picture is centered.
Caption Position Adjustment (Horizontal)
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S18".
3. A black text box appears on the screen. (see Figure B. below)
4. Adjust "S18" data value so that text box is positioned in the center of the screen.
3.58MHz Trap Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service adjustment "S16".
3. This is a two position adjustment, "00" is ON, "01" is OFF.
4. Models should be adjusted as follows.
MODEL "S16" 27N-S100 01 27N-S180 01
CN27S10 00 CN27S14 01 CN27S18 01
Sharpness and Audio Balance Adjust­ments
1. Receive a good local channel.
2. Enter the service mode and select the service adjustments "S05" for sharpness and "S17" for balance.
» Sharpness Adjustment
3. Adjust data value to "28"(center of data range) for sharpness adjustment.
» Audio Balance Adjustment
4. Adjust data value to "20"(center of data range) for audio balance adjustment.
Energy save offset Adjustment
1. Enter the service mode and select the service adjustment "S20".
2. Adjust data value to "23".
Note : This position is used to preset the level for the
energy save function.
Other Adjustments
1. Enter the service mode.
2. Adjust the following data values as listed below.
Figure B.
S21 "03" DDE OFFSET S22 "00" OSD SETUP S23 "00" TUNER SETUP
11
Page 12
27N-S100, 27N-S180 CN27S10/14/18
MTS ADJUSTMENT
MTS Level Adjustment
1. Feed the following monaural signal to pin (14) of IC3001.
Monaural signal : 300Hz, 245mVrms
2. Connect the rms voltmeter to pin (39) of IC3001.
3. Enter the service mode and select the service adjustment "M01".
4. Adjust the data so that the rms voltmeter reads.
Spec.: 490 ±10mVrms.
MTS VCO Adjustment
1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µF, 50V) in between positive(+) side of C3005 and ground.
4. Enter the service mode and select the service adjustment "M02"
5. Adjust the data so that the frequency counter reads.
Spec.: 62.94 ±0.75kHz.
Filter Adjustment
1. Feed the following stereo pilot signal to pin (14) of IC3001 . Stereo pilot signal: 9.4kHz, 600mVrms.
2. Enter the service mode and select the service adjustment "M03".
3. Adjust the data at the point where "OK" appears on the screen. The "OK" represents the approximate center of the adjustable range of the data.
Separation Adjustment
1. Connect the rms voltmeter to pin (39) of IC3001.
2. Receive the following composite stereo signal 1. Composite stereo signal: 30% modulation, left channel only, noise reduction on, 300Hz
3. Enter the service mode and select the service adjustment "M04".
4. Adjust the data until the AC voltage reading of the rms voltmeter is minimum.
5. Receive the following composite stereo signal 2. Stereo signal: 30% modulation, left channel only, noise reduction on, 3kHz
6. Enter the service mode and select the service adjustment "M05".
7. Adjust the data until the AC voltage reading of the rms voltmeter is minimum.
8. Take the above steps 1 thru 8 again for fine adjustment.
12
Page 13
CHASSIS LAYOUT
27N-S100, 27N-S180 CN27S10/14/18
H
(27N-S100, CN27S14) PWB-K
G
F
E
PWB-B
(27N-S180, CN27S18) PWB-K
PWB-H
PWB-A
D
C
B
A
13
1716 1918151413121110
654321
Page 14
27N-S100, 27N-S180 CN27S10/14/18
MODEL 27N-S100 BLOCK DIAGRAM
H
H
G
G
F
F
E
E
D
D
C
C
B
B
A
A
87109654321
654321
14
Page 15
MODELS 27N-S180, CN27S18 BLOCK DIAGRAM
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
1716 1918151413121110
654321
15
Page 16
27N-S100, 27N-S180 CN27S10/14/18
MODEL CN27S10 BLOCK DIAGRAM
H
H
G
G
F
F
E
E
D
D
C
C
B
B
A
A
87109654321
654321
16
Page 17
MODEL CN27S14 BLOCK DIAGRAM
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
1716 1918151413121110
654321
17
Page 18
27N-S100, 27N-S180 CN27S10/14/18
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
H
1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/8 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted. (P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
G
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color signal.
F
E
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control.
2.
indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
å
AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS.
'
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES å ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ' : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
WAVE FORMS
D
C
B
A
87109654321
18
Page 19
SCHEMATIC DIAGRAM: CRT and FRONT AV Units
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
1716 1918151413121110
654321
19
Page 20
MODEL 27N-S100 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
20
21
Page 21
MODEL 27N-S100 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
22
23
Page 22
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
24
25
Page 23
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
26
27
Page 24
MODEL CN27S10 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
28
29
Page 25
MODEL CN27S10 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
30
31
Page 26
MODEL CN27S14 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
32
33
Page 27
MODEL CN27S14 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
121110987654321
34
35
Page 28
27N-S100, 27N-S180 CN27S10/14/18
MODELS 27N-S100, CN27S14 SCHEMATIC DIAGRAM: S-VIDEO Unit
H
G
F
E
D
C
B
A
654321
36
Page 29
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM: DIGICOM/S-VIDEO Unit
H
G
F
27N-S100, 27N-S180 CN27S10/14/18
E
D
C
B
A
654321
37
Page 30
27N-S100, 27N-S180 CN27S10/14/18
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
A
PWB-A : MAIN Unit (Wiring Side)
654321
38
Page 31
27N-S100, 27N-S180 CN27S10/14/18
H
G
F
E
D
C
B
A
PWB-A : MAIN Unit (Chip Parts Side)
654321
39
Page 32
27N-S100, 27N-S180 CN27S10/14/18
H
G
F
E
PWB-B : CRT Unit (Wiring Side)
D
C
B
PWB-H : FRONT AV Unit (Wiring Side)
A
654321
40
Page 33
27N-S100, 27N-S180 CN27S10/14/18
J1
C1513
R1516
D1504
D1503
R1517R1515
R1519
D1502
R1514
C1510
P1503
16
D1501
KC
H
R1506
R1503
R1501
R1502
G
Q1501
R1505
C1502
Q1502 R1504
Q1503
R1510
R1508
R1507
Q1504
L1502
R1509
R1511
L1501
J3
L1503
R1513
R1512
C1503
J4
J2
IC1501
C1508
J5
C1506
C1505
C1504
C1501
F
R1518
5
KA
P1501
C1511
1
J6
C1507
C1512
5
C1509
KB
P1502
1
PWB-K : S-VIDEO Unit (Wiring Side)
E
(Only for 27N-S100, CN27S14)
Q1405
Q1405
Q1404 R1413
R1404
R1406
R1419
RJ5
Q1402
Q1406
R1403
R1422
R1412
C1421
Q1407
C1425
R1418
R1420
R1415
C1423
R1414
C1426
R1421
RJ4
C1454
1
R1410
C1428
IC1451
R1425
R1454
C1453
R1451
R1452
C1451
1
R1455
R1453
1
Q1403
R1409
C1413
Q1401
R1417
R1416
C1411
C1424
D
1
C1403
C1404
C1406
C1405
RJ1
R1407
C1420
C
CJ1
RJ2
C1417 R1424
C1416
1
IC1401
C1412
C1409
C1407
RJ3
C1410 R1408
1
B
R1401
R1402
R1405
C1401
PWB-K : DIGICOM/S-VIDEO Unit (Wiring Side)
A
(Only for 27N-S180, CN27S18)
41
654321
Page 34
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT P ARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PAR T NO. 4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call Toll­Free; 1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
MARK: X- RAY RELATED PARTS
Ref. No. Part No. Description Code
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi`eces et dans les diagrammes sch élematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl'usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE 2. NO. DE REF
3. NO. DE PIECE 4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No. Part No. Description Code
PICTURE TUBE
çå V101 VB68ADT2503*S M Picture Tube (I.T.C.) CN
å L703 RCiLG0038MEZZ M Degaussing Coil AQ
MSPRT0002MEZZ M Spring for CRT AA QEARC2702MEZZ M Grounding Part AH
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-ADUNTKA126WEK4 – MAIN Unit (27N-S100) — PWB-ADUNTKA126WEK5 – MAIN Unit
(27N-S180, CN27S18) PWB-ADUNTKA126WEK8 – MAIN Unit (CN27S10) — PWB-ADUNTKA126WEL6 – MAIN Unit (CN27S14) — PWB-BDUNTK9510WEK1 – CRT Unit — PWB-HDUNTK9310WEK1 – FRONT AV Unit — PWB-KDUNTKA114WEK0 – S-VIDEO Unit
(27N-S100, CN27S14) PWB-KDUNTKA115WEK0 – DIGICOM/S-VIDEO Unit
(27N-S180, CN27S18)
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10) PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18) PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED
AS AN ASSEMBLY BUT NOT INDEPENEDENTLY.
å TU51 VTUVTST5UF78S M Tuner AX
or VTU115B8035AH
INTEGRATED CIRCUITS
IC101 VHiKA78S05P-1 J KA78S05P AD
çå IC201 RH-iX3253CEZZ J TA1268AN AV
IC351 VHiAN7511//-1 J I.C. AK IC352 VHiAN7511//-1 J I.C. AK
å IC501 VHiTA8427K/-1 J TA8427K AL å IC701 VHiSTRF66261E J STR-F6626 AX å IC702 RH-FX0034CEZZ J PC817 AE
or RH-FX0002GEZZ
å IC703 VHiSE120N//-1 J SE120N AG å IC750 VHiKA7809Pi-1 M KA7809PI AE å IC751 VHiKA7809Pi-1 M KA7809PI AE
IC951 VHiMM1111XF1E J MM1111XFBE AE
(CN27S10)
IC951 VHiMM1113XF1E J MM1113XFBE AE
(27N-S100/180, CN27S14/18) IC2001 RH-iX3366CEZZ M TMPA8700CPF-164 AT IC2040 VHiKiA7045A-1 J KIA7045A AD IC2101 VHiM24C16B/-1 J M24C16-BN6 AG IC3001 VHiCXA2074Q-1 J CXA2074Q AY
TRANSISTORS
You can substitute "VS2SC2412-C-1" for "VS2SD601AR/-1".
Q201 VS2SC2735//1E J 2SC2735 AC Q251 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S18)
42
Page 35
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10) PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18) PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
Q252 VS2SD601AR/-1 J 2SD601AR AC
å D753 RH-DX0441CEZZ J Diode AC å D754 RH-DX0441CEZZ J Diode AC
D755 VHD1SS119//-1 J Diode AB
å D756 RH-DX0441CEZZ J Diode AC
D2001 VHD1SS119//-1 J Diode AB D2011 RH-EX0611GEZZ J Zener Diode, 5.1V AA
(27N-S180, CN27S18)
Q253 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S18)
Q301 VS2SD601AR/-1 J 2SD601AR AC
å PR701 RMPTP0092CEZZ J Packaged Circuit AH
X801 RCRSB0205CEZZ J Crystal AF
Q401 VS2SD601AR/-1 J 2SD601AR AC Q402 VS2SB709AR/-1 J 2SB709AR AC
or
VS2SA1037KR-1 Q403 VS2SD601AR/-1 J 2SD601AR AC Q421 VS2SB709AR/-1 J 2SB709AR (CN27S10) AC
or
VS2SA1037KR-1
CF301 RFiLC0029TAZZ J Ceramic Filter AD CF401 RFiLC0013CEZZ J Ceramic Filter AE CF631 RFiLA0034CEZZ J Ceramic Filter AD CF2040
Q451 VS2SB709AR/-1 J 2SB709AR AC
or
VS2SA1037KQ-1
SF201 RFiLC0405CEZZ J SAW Filter AH
Q601 VS2SC2482//-1 J 2SC2482 AD
å Q602 VS2SD2539//1E J 2SD2539 AP
Q751 VS2SC3198-Y-1 J 2SC3198(Y) AA Q901 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S10/14/18)
Q902 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S10/14/18)
L201 VP-XF1R2K0000 J Peaking 1.2µH AB L202 RCiLi0588CEZZ J VCO Coil AF L251 VP-XF390K0000 J Coil (27N-S180, CN27S18) AB L301 VP-XF8R2K0000 J Peaking 8.2µH AB L302 RCiLi0613CEZZ J IF Coil AE
Q903 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S10/14/18)
Q904 VS2SD601AR/-1 J 2SD601AR AC
(27N-S180, CN27S10/14/18) Q2060 VS2SD601AR/-1 J 2SD601AR AC Q2201 VS2SD601AR/-1 J 2SD601AR AC Q2211 VS2SD601AR/-1 J 2SD601AR AC
L401 VP-XF6R8K0000 J Peaking 6.8µH AB L402 VP-XF3R3K0000 J Peaking 3.3µH AB L403 VP-XF8R2K0000 J Peaking 8.2µH AB L404 VP-XF8R2K0000 J Peaking 8.2µH AB L421 VP-XF680K0000 J Peaking 68µH (CN27S10) AB L672 RCiLZ0101MEZZ M Coil AE
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D51 RH-EX0611GEZZ J Zener Diode, 5.1V AA D52 RH-EX0673GEZZ J Zener Diode, 32V AB D53 RH-EX0611GEZZ J Zener Diode, 5.1V AA D103 VHD1SS119//-1 J Diode AB D401 VHD1SS119//-1 J Diode AB D402 RH-EX0604GEZZ J Zener Diode, 3.9V AB D454 RH-EX0611GEZZ J Zener Diode, 5.1V AA D455 VHD1SS119//-1 J Diode AB D456 VHD1SS119//-1 J Diode AB D457 RH-EX0217CEZZ J Zener Diode AB D458 RH-EX0217CEZZ J Zener Diode AB D459 VHD1SS119//-1 J Diode AB
å D501 RH-DX0131CEZZ J Diode AC å D510 RH-DX0441CEZZ J Diode AC
D621 RH-EX0631GEZZ J Zener Diode, 9.1V AA
å D622 RH-DX0131CEZZ J Diode AC çå D651 RH-DX0131CEZZ J Diode AC çå D652 RH-EX1313CEZZ M Zener Diode, 9.1V AB çå D653 VHD1SS119//-1 J Diode AB çå D654 VHD1SS119//-1 J Diode AB
å D701 RH-DX0154CEZZ J Diode AC
å D702 RH-DX0154CEZZ J Diode AC
å D703 RH-DX0154CEZZ J Diode AC
å D704 RH-DX0154CEZZ J Diode AC
D705 VHD1SS82///1A J Diode AC D706 RH-DX0066GEZZ J Diode AB D707 VHD1SS82///1A J Diode AC D708 RH-DX0066GEZZ J Diode AB
å D709 RH-DX0229CEZZ J Diode AF
å D712 RH-DX0407CEZZ J Diode AD
å D713 RH-EX0673GEZZ J Zener Diode, 32V AB
å D715 RH-EX0610GEZZ J Zener Diode AA
D716 VHD1SS119//-1 J Diode AB D717 RH-EX0650GEZZ J Zener Diode, 16V AB
å D725 RH-DX0407CEZZ J Diode AD
å D751 RH-DX0441CEZZ J Diode AC
å D752 RH-DX0441CEZZ J Diode AC
å L701 RCiLF0025PEZZ M Coil AK å L702 RCiLF0025PEZZ M Coil AK å L705 RCiLP0179CEZZ J Coil AD
L729 RCiLP0179CEZZ J Coil AD L2040 RCiLB0131CEZZ J Oscillation Coil AE
T601 RTRNZ0057PEZZ R Transformer AK
çå T602 RTRNF0033MEZZ M H-Volt Transformer AY
å T701 RTRNP0543CEZZ J Power Transformer AM å T702 RTRNZ0017MEZZ M Transformer AM
C51 VCEA0A1CW476M J 47 16V EL. AB C53 VCEA0A1HW105M J 1 50V EL. AB C54 VCEA0A1HW475M J 4.7 50V EL. AB C55 VCEA0A1CW108M J 1000 16V EL. AD C56 VCKYCY1CB104K J 0.1 16V Ceramic AB C103 VCEA0A1CW228M J 2200 16V EL. AB C201 VCKYMN1HB102K J 1000p 50V Ceramic AA C202 VCKYCY1HF103Z J 0.01 50V Ceramic AA C203 VCKYCY1HB102K J 1000p 50V Ceramic AA C204 VCKYCY1HF103Z J 0.01 50V Ceramic AA C205 VCEA0A1HW474M J 0.47 50V EL. AB C206 VCEA0A1CW337M J 330 16V EL. AC C207 VCKYCY1HF103Z J 0.01 50V Ceramic AA C208 VCEA0A1HW474M J 0.47 50V EL. AB C209 VCKYCY1HB222K J 2200p 50V Ceramic AA C210 VCKYCY1HB102K J 1000p 50V Ceramic AA C251 VCQYTA1HM103K J 0.01 50V Mylar AB
PACKAGED CITCUITS
or RCRSB0001PEZZ
FILTERS
RFiLC0121GEZZ J Ceramic Filter AD or RFiLA0099CEZZ
COILS
or RCiLi0605CEZZ
or RCiLZ0102MEZZ
TRANSFORMERS
or RTRNF0037MEZZ
or RTRNZ0022MEZZ
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
(27N-S180, CN27S18)
43
Page 36
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10) PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18) PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
C252 VCQYTA1HM103K J 0.01 50V Mylar AB C253 VCCCCY1HH470J M 47 50V Ceramic AA C301 VCCCCY1HH330J J 33p 50V Ceramic AA
C302 VCCCCY1HH151J J 150p 50V Ceramic AA C303 VCCCCY1HH390J J 39p 50V Ceramic AA C307 VCCCCY1HH1R5C J 1.5p 50V Ceramic AD C308 VCKYCY1HB102K J 1000p 50V Ceramic AA C309 VCEA0A1CW337M J 330 16V EL. AC C313 VCEA0A1CW476M J 47 16V EL. AB C351 VCEA0A1HW106M J 10 50V EL. AB C352 VCKYCY1HB332K J 3300p 50V Ceramic AA C354 VCEA0A1HW106M J 10 50V EL. AB C355 VCKYCY1HB332K J 3300p 50V Ceramic AA C356 VCEA0A1HW106M J 10 50V EL. AB C358 VCEA0A1CW477M J 470 16V EL. AC C359 VCEA0A1HW106M J 10 50V EL. AB C401 VCKYCY1HB331K J 330p 50V Ceramic AA C402 VCCCCY1HH101J J 100p 50V Ceramic AA C403 VCKYCY1CB104K J 0.1 16V Ceramic AB C404 VCEA0A1HW106M J 10 50V EL. AB C405 VCEA0A1HW335M J 3.3 50V EL. AB C406 VCEA0A1HW225M J 2.2 50V EL. AB C408 VCEA0A1HW106M J 10 50V EL. AB C409 VCEA0A1HW335M J 3.3 50V EL. AB C410 VCQYTA1HM104K J 0.1 50V Mylar AC C411 VCEA0A1CW337M J 330 16V EL. AC C412 VCKYCY1HB103K J 0.01 50V Ceramic AA C413 VCKYCY1HB103K J 0.01 50V Ceramic AA C414 VCKYCY1CB104K J 0.1 16V Ceramic AB
C421 VCCCCY1HH330J J 33p 50V Ceramic AA C422 VCEA0A1CW476M J 47 16V EL. AB
C451 VCQYTA1HM104K J 0.1 50V Mylar AC C452 VCEA0A1HW475M J 4.7 50V EL. AB C453 VCEA0A1CW226M J 22 16V EL. AB C501 VCKYPA2HB102K J 1000p 500V Ceramic AA C502 VCEA0A1VW108M J 1000 35V EL. AD C510 VCFYSA1JB564J M 0.56 63V Mylar AB C511 VCKYPA2HB391K J 390p 500V Ceramic AA C512 VCQYTA1HM473K J 0.047 50V Mylar AB C513 VCQYTA1HM103K J 0.01 50V Mylar AB C514 VCEA0A1VW107M J 100 35V EL. AC C515 VCEA0A1HW474M J 0.47 50V EL. AB C516 VCSATA1VE684K J 0.68 35V Tantalum AC C517 VCEA0A1VW108M J 1000 35V EL. AD C518 VCFYSA1JB473J M 0.047 63V Mylar AA C551 VCSATA1CE225K J 2.2 16V Tantalum AB C552 VCEA0A1HW225M J 2.2 50V EL. AB C606 VCKYPA2HB561K J 560p 500V Ceramic AA C607 VCKYPA1HB472K J 4700p 50V Ceramic AA
çå C610 VCFPVC3CA772H J 7700p 1.6kV M-Poly. AF çå C611 VCFPVC3CA772H J 7700p 1.6kV M-Poly. AF
C615 VCKYPA2HB102K J 1000p 500V Ceramic AA
å C623 VCEA4A2EN106M J 10 250V EL. AD
C631 VCEA0A1HW335M J 3.3 50V EL. AB C632 VCQYTA1HM103K J 0.01 50V Mylar AB C633 VCEA0A1CW477M J 470 16V EL. AC C652 VCEA0A1HW106M J 10 50V EL. AB C653 VCEA0A1HW106M J 10 50V EL. AB C680 VCFPVC2DB474J M 0.47 200V M-Poly. AE C682 VCKYPA2HB331K J 330p 500V Ceramic AA
å C701 RC-FZ012SCEZZ J 0.22
or RC-FZ012SGEZZ or RC-FZ037SCEZZ
(27N-S180, CN27S18) (27N-S180, CN27S18)
(CN27S10) (CN27S10)
AC250V
Plastic AD
å C705 RC-EZ0800CEZZ J 560 200V EL. AQ
å C706 RC-KZ0092GEZZ J 0.0033
å C723 RC-EZ0724CEZZ J 100 160V EL. AG å C725 RC-EZ0809CEZZ J 220 160V EL. AL
å C730 RC-EZ0385CEZZ J 1000 16V EL. AE å C731 RC-EZ0385CEZZ J 1000 16V EL. AE
or
RC-FZ017SCEZZ C702 RC-KZ0029CEZZ J 0.01 C703 RC-KZ0029CEZZ J 0.01
or
RC-EZ0719CEZZ
or
RC-EZ1336CEZZ C707 VCFPVC3CA222H J 2200p 1.6kV M-Poly. AE
C708 VCCSPA1HL471J J 470p 50V Ceramic AA C709 VCEA0A1VW107M J 100 35V EL. AC C710 VCQYTA1HM102J J 1000p 50V Mylar AA C717 VCKYPA2HB472K J 4700p 500V Ceramic AB C718 VCKYPA2HB472K J 4700p 500V Ceramic AB C722 VCQYTA1HM104K J 0.1 50V Mylar AB
C726 RC-KZ0338CEZZ J 560p 2kV Ceramic AD C727 RC-KZ0338CEZZ J 560p 2kV Ceramic AD C729 VCEA0A1CW106M J 10 16V EL. AB
C732 VCKYPA2HB102K J 1000p 500V Ceramic AA C741 VCKYPA2HB102K J 1000p 500V Ceramic AA C742 VCKYPA2HB102K J 1000p 500V Ceramic AA C753 VCEA0A1CW107M J 100 16V EL. AC C755 VCEA0A1CW476M J 47 16V EL. AB C772 VCEA0A1VW477M J 470 35V EL. AB C801 VCQYTA1HM223K J 0.022 50V Mylar AB C802 VCEA0A1HW474M J 0.47 50V EL. AB C803 VCCCCY1HH110J J 11p 50V Ceramic AA C804 VCKYCY1CB104K J 0.1 16V Ceramic AB C805 VCKYCY1CB104K J 0.1 16V Ceramic AB C806 VCKYCY1CB104K J 0.1 16V Ceramic AB C807 VCCCCY1HH221J J 220p 50V Ceramic AA C808 VCKYCY1HB102K J 1000p 50V Ceramic AA
C901 VCEA0A1HW335M J 3.3 50V EL. AB C902 VCEA0ACW476M J 47 16V EL. AB C903 VCEA0A1HW335M J 3.3 50V EL. AB C908 VCEA0A1HW225M J 2.2 50V EL. AB
C909 VCEA0A1HW225M J 2.2 50V EL. AB C910 VCKYCY1HB681K J 680p 50V Ceramic AA
C911 VCKYCY1HB681K J 680p 50V Ceramic AA C922 VCEA0A1HW335M J 3.3 50V EL. AB C923 VCEA0A1HW335M J 3.3 50V EL. AB C931 VCKYCY1EB183K J 0.018 25V Ceramic AA C932 VCKYCY1EB183K J 0.018 25V Ceramic AA C951 VCEA0A1HW106M J 10 50V EL. AB
C952 VCEA0A1HW106M J 10 50V EL. AB C954 VCKYCY1HF103Z J 0.01 50V Ceramic AA C955 VCEA0A1CW106M J 10 16V EL. AB C956 VCEA0A1CW106M J 10 16V EL. AB
C2001 VCCCCY1HH101J J 100p 50V Ceramic AA C2002 VCCCCY1HH101J J 100p 50V Ceramic AA C2040 VCEA0A1AW107M J 100 10V EL. AB C2041 VCEA0A1HW105M J 1 50V EL. AB C2060 VCKYCY1CB104K J 0.1 16V Ceramic AB C2061 VCCCCY1HH101J J 100p 50V Ceramic AA C2062 VCEA0A1AW107M J 100 10V EL. AB C2201 VCKYCY1HB152K J 1500p 50V Ceramic AA C2202 VCCCCY1HH390J J 39p 50V Ceramic AA C2601 VCEA0A1HW475M J 4.7 50V EL. AB
AC250V
Ceramic AC
AC250V
Ceramic AC
AC250V
Ceramic AC
(CN27S10) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18)
(27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18) (27N-S180, CN27S10/14/18)
(27N-S100/180, CN27S14/18)
44
Page 37
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
RJ61 VRS-CY1JF000J J 0 1/16W M-Ox. AA
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18) PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
C2602 VCCCCY1HH101J J 100p 50V Ceramic AA C3001 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3002 VCKYCY1HB562K J 5600p 50V Ceramic AA C3003 VCQYTA1HM123K J 0.012 50V Mylar AA C3004 VCEA0A1HW105M J 1 50V EL. AB C3005 VCEA0A1HW475M J 4.7 50V EL. AB C3006 VCEA0A1HW106M J 10 50V EL. AB C3007 VCEA0A1HW475M J 4.7 50V EL. AB C3008 VCKYCY1HF103Z J 0.01 50V Ceramic AA C3009 VCEA0A1CW227M J 220 16V EL. AC C3010 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3011 VCEA0A1HW475M J 4.7 50V EL. AB C3012 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3013 VCKYCY1HB272K J 2700p 50V Ceramic AA C3014 VCQYTA1HM473K J 0.047 50V Mylar AB C3015 VCSATA1CE335K J 3.3 16V Tantalum AC C3016 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3017 VCSATA1CE106K J 10 16V Tantalum AD C3018 VCEA0A1HW105M J 1 50V EL. AB C3019 VCEA0A1HW475M J 4.7 50V EL. AB C3020 VCEA0A1HW475M J 4.7 50V EL. AB C3021 VCEA0A1HW475M J 4.7 50V EL. AB C3022 VCEA0A1HW475M J 4.7 50V EL. AB
RESISTORS
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
RJ1 VRD-MN2BE000J J 0 1/8W Carbon AA RJ10 VRD-MN2BE000J J 0 1/8W Carbon AA RJ11 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ12 VRD-MN2BE000J J 0 1/8W Carbon AA RJ13 VRD-MN2BE000J J 0 1/8W Carbon AA RJ14 VRD-MN2BE000J J 0 1/8W Carbon AA RJ15 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ17 VRD-MN2BE000J J 0 1/8W Carbon AA RJ19 VRD-MN2BE000J J 0 1/8W Carbon AA RJ20 VRD-MN2BE000J J 0 1/8W Carbon AA RJ21 VRD-MN2BE000J J 0 1/8W Carbon AA RJ22 VRD-MN2BE000J J 0 1/8W Carbon AA RJ25 VRD-MN2BE000J J 0 1/8W Carbon AA RJ26 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ28 VRD-MN2BE000J J 0 1/8W Carbon AA RJ29 VRD-MN2BE000J J 0 1/8W Carbon AA RJ30 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ31 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ32 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ33 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ35 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ36 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ37 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ38 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ39 VRD-MN2BE000J J 0 1/8W Carbon AA RJ40 VRD-MN2BE000J J 0 1/8W Carbon AA RJ41 VRD-MN2BE000J J 0 1/8W Carbon AA RJ42 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ43 VRD-MN2BE000J J 0 1/8W Carbon AA RJ46 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ48 VRD-MN2BE000J J 0 1/8W Carbon AA RJ49 VRD-MN2BE000J J 0 1/8W Carbon AA RJ50 VRD-MN2BE000J J 0 1/8W Carbon AA RJ51 VRD-MN2BE000J J 0 1/8W Carbon AA RJ52 VRS-CY1JF000J J 0 1/16W M-Ox. AA
(CN27S10) RJ54 VRD-MN2BE000J J 0 1/8W Carbon AA RJ55 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ56 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ57 VRD-MN2BE000J J 0 1/8W Carbon AA RJ58 VRD-MN2BE000J J 0 1/8W Carbon AA RJ59 VRS-CY1JF000J J 0 1/16W M-Ox. AA
(27N-S100/180, CN27S14/18) RJ60 VRD-MN2BE000J J 0 1/8W Carbon AA
RJ63 VRD-MN2BE000J 0 1/8W Carbon AA RJ64 VRD-MN2BE000J J 0 1/8W Carbon AA RJ67 VRS-CY1JF000J J 0 1/16W M-Ox. AA
å R51 VRS-RG3AB151J M 150 1W M-Ox. AA å R52 VRS-RG3DB123J J 12k 2W M-Ox. AA å R53 VRS-RG3AB470J J 47 1W M-Ox. AA
R54 VRD-MN2BE101J J 100 1/8W Carbon AA R55 VRD-MN2BE101J J 100 1/8W Carbon AA R56 VRD-MN2BE823J J 82k 1/8W Carbon AA R57 VRD-MN2BE392J J 3.9k 1/8W Carbon AA R201 VRD-MN2BE151J J 150 1/8W Carbon AA R202 VRD-MN2BE122J J 1.2k 1/8W Carbon AA R203 VRD-MN2BE682J J 6.8k 1/8W Carbon AA R204 VRD-MN2BE270J J 27 1/8W Carbon AA R205 VRS-CY1JF331J J 330 1/16W M-Ox. AA R206 VRD-MN2BE121J J 120 1/8W Carbon AA R207 VRD-MN2BE4R7J J 4.7 1/8W Carbon AA R208 VRD-MN2BE331J J 330 1/8W Carbon AA R209 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R251 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R252 VRD-MN2BE562J J 5.6k 1/8W Carbon AA R253 VRD-MN2BE332J J 3.3k 1/8W Carbon AA R254 VRD-MN2BE223J J 22k 1/8W Carbon AA R255 VRS-CY1JF563J J 56k 1/16W M-Ox. AA R256 VRS-CY1JF182J J 1.8k 1/16W M-Ox. AA R257 VRS-CY1JF470J J 47 1/16W M-Ox. AA R258 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R259 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R301 VRD-MN2BE222J J 2.2k 1/8W Carbon AA
R302 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R303 VRD-MN2BE103J J 10k 1/8W Carbon AA R304 VRD-MN2BE333J J 33k 1/8W Carbon AA R305 VRD-MN2BE102J J 1k 1/8W Carbon AA R306 VRD-MN2BE152J J 1.5k 1/8W Carbon AA R351 VRD-MN2BE683J J 68k 1/8W Carbon AA R352 VRD-MN2BE103J J 10k 1/8W Carbon AA R353 VRD-RA2BE822J J 8.2k 1/8W Carbon AA R354 VRD-MN2BE223J J 22k 1/8W Carbon AA R355 VRD-MN2BE683J J 68k 1/8W Carbon AA R356 VRD-MN2BE103J J 10k 1/8W Carbon AA R357 VRD-MN2BE822J J 8.2k 1/8W Carbon AA R358 VRD-MN2BE223J J 22k 1/8W Carbon AA R401 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R402 VRS-CY1JF331J J 330 1/16W M-Ox. AA R403 VRS-CY1JF391J J 390 1/16W M-Ox. AA R404 VRD-MN2BE102J J 1k 1/8W Carbon AA R405 VRS-CY1JF470J J 47 1/16W M-Ox. AA R406 VRS-CY1JF680J J 68 1/16W M-Ox. AA R407 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R408 VRS-CY1JF471J J 470 1/16W M-Ox. AA R409 VRD-MN2BE562J J 5.6k 1/8W Carbon AA R410 VRD-RA2BE154J J 150k 1/8W Carbon AA R411 VRD-MN2BE153J J 15k 1/8W Carbon AA R412 VRD-RA2BE561J J 560 1/8W Carbon AA R413 VRS-CY1JF101J J 100 1/16W M-Ox. AA R414 VRS-CY1JF101J J 100 1/16W M-Ox. AA R415 VRS-CY1JF101J J 100 1/16W M-Ox. AA R416 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R421 VRD-MN2BE152J J 1.5k 1/8W Carbon AA R422 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA
(27N-S100, CN27S10/14)
(27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18) (27N-S180, CN27S18)
(27N-S100/180, CN27S14/18) (CN27S10) (CN27S10)
45
Page 38
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10) PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18) PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
R423 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
(CN27S10)
R424 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(CN27S10)
å R451 VRS-RG2HC103J J 10k 1/2W M-Ox. AA
R452 VRD-RM2HD153J J 15k 1/2W Carbon AA R453 VRD-RA2EE683J J 68k 1/4W Carbon AA R454 VRD-MN2BE102J J 1k 1/8W Carbon AA R456 VRD-MN2BE682J J 6.8k 1/8W Carbon AA R458 VRD-MN2BE152J J 1.5k 1/8W Carbon AA
å R501 VRN-RL3ABR56J J 0.56 1W M-Film AA
R510 VRD-MN2BE471J J 470 1/8W Carbon AA R511 VRD-RA2BE823G J 82k 1/8W Carbon AB R512 VRD-RA2BE124G J 120k 1/8W Carbon AA R513 VRD-RA2BE473J J 47k 1/8W Carbon AA R514 VRD-MN2BE101J J 100 1/8W Carbon AA R519 VRD-RA2BE153G J 15k 1/8W Carbon AA R520 VRD-MN2BE184J J 180k 1/8W Carbon AA R523 VRN-RL3AB1R0J M 1 1W M-Film AA R524 VRS-RG3AB391J J 390 1W M-Ox. AA R526 VRD-MN2BE562J J 5.6k 1/8W Carbon AA R551 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R552 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R553 VRD-MN2BE333J J 33k 1/8W Carbon AA R554 VRD-MN2BE333J J 33k 1/8W Carbon AA
å R604 VRS-RG3LB392J M 3.9k 3W M-Ox. AB
R605 VRD-RA2BE331J J 330 1/8W Carbon AA R606 VRD-RA2BE331J J 330 1/8W Carbon AA
å R607 VRS-RG3LB392J M 3.9k 3W M-Ox. AB å R609 VRS-RG3AB562J M 5.6k 1W M-Ox. AA
R610 VRD-RM2HD220J J 22 1/2W Carbon AA
å R611 VRS-KA3NG3R3K J 3.3 7W M-Ox. AD å R621 VRN-RL3DB1R2J M 1.2 2W M-Film AA å R622 VRN-RL3ABR39J M 0.39 1W M-Film AA å R623 VRN-RL3AB2R7J M 2.7 1W M-Film AA å R624 VRS-RG3DB332J M 3.3k 2W M-Ox. AA
R625 VRD-MN2BE102J J 1k 1/8W Carbon AA R627 VRD-RM2HD224J J 220k 1/2W Carbon AA R631 VRS-CY1JF391J J 390 1/16W M-Ox. AA R632 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA R633 VRD-MN2BE472J J 4.7k 1/8W Carbon AA R634 VRD-RA2BE4R7J J 4.7 1/8W Carbon AA
çå R651 VRS-RG2HC270J M 27 1/2W M-Ox. AA çå R652 VRN-RA2BK103F J 10k 1/8W M-Film AA çå R653 VRN-RA2BK822F J 8.2k 1/8W M-Film AA çå R654 VRD-MN2BE184J J 180k 1/8W Carbon AA çå R655 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R690 VRS-RG2HC102J J 1k 1/2W M-Ox. AA
å R701 RR-HZ0048CEZZ J 3.9M 1/2W Solid AB å R702 VRW-KQ3NC1R2K J 1.2 7W Cement AE
R704 VRD-RM2HD154J J 150k 1/2W Carbon AA
å R705 VRN-RL3DBR22J J 0.22 2W M-Film AA å R706 VRN-RL3DBR27J M 0.27 2W M-Film AA
R707 VRS-RG2HC681J J 680 1/2W M-Ox. AA
å R709 VRN-GA2EB1R0J J 1 1/4W M-Film AA
R710 VRD-RM2HD470J J 47 1/2W Carbon AA R711 VRD-RA2BE242J J 2.4k 1/8W Carbon AA
å R715 VRS-RG3DB153J J 15k 2W M-Ox. AA å R723 VRN-RL3DBR39J M 0.39 2W M-Film AA
R724 VRS-RG2HC332J J 3.3k 1/2W M-Ox. AA R725 VRS-RG2HC821J M 820 1/2W M-Ox. AA R726 VRS-RG2HC122J M 1.2k 1/2W M-Ox. AA R727 VRD-RA2BE271J J 270 1/8W Carbon AA
å R728 VRN-RL3LB4R7J M 4.7 3W M-Film AB
R734 VRD-RM2HD124J J 120k 1/2W Carbon AA
å R737 VRN-RL3DBR56J M 0.56 2W M-Film AA
R751 VRD-MN2BE473J J 47k 1/8W Carbon AA R801 VRD-MN2BE332J J 3.3k 1/8W Carbon AA R802 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R803 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R804 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R805 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R806 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R807 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
(CN27S10)
R808 VRD-RA2BE102J J 1k 1/8W Carbon AA
(CN27S10)
R901 VRD-RA2BE331J J 330 1/8W Carbon AA
(27N-S180, CN27S10/14/18)
R903 VRD-MN2BE102J J 1k 1/8W Carbon AA
(27N-S180, CN27S10/14/18)
R904 VRS-CY1JF683J J 68k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R905 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R906 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R907 VRS-CY1JF182J J 1.8k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R908 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R910 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R911 VRS-CY1JF683J J 68k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R912 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R913 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R914 VRS-CY1JF182J J 1.8k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R915 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R922 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18)
R923 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S180, CN27S10/14/18) R924 VRS-CY1JF750J J 75 1/16W M-Ox. AA R925 VRD-MN2BE104J J 100k 1/8W Carbon AA R926 VRD-MN2BE104J J 100k 1/8W Carbon AA R931 VRS-CY1JF750J J 75 1/16W M-Ox. AA
(27N-S100/180, CN27S14/18) R932 VRS-CY1JF750J J 75 1/16W M-Ox. AA
(27N-S100/180, CN27S14/18) R951 VRD-RA2BE101J J 100 1/8W Carbon AB R952 VRD-MN2BE102J J 1k 1/8W Carbon AA R953 VRS-CY1JF101J J 100 1/16W M-Ox. AA
(27N-S100/180, CN27S14/18) R961 VRD-RA2BE101J J 100 1/8W Carbon AB R962 VRD-RA2BE101J J 100 1/8W Carbon AB R2001 VRD-RA2BE562J J 5.6k 1/8W Carbon AA R2002 VRD-MN2BE103J J 10k 1/8W Carbon AA R2004 VRD-MN2BE101J J 100 1/8W Carbon AA R2006 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2008 VRD-MN2BE333J J 33k 1/8W Carbon AA R2009 VRD-RA2BE102J J 1k 1/8W Carbon AA R2010 VRD-MN2BE102J J 1k 1/8W Carbon AA R2012 VRS-CY1JF471J J 470 1/16W M-Ox. AA R2016 VRS-CY1JF223J J 22k 1/16W M-Ox. AA R2020 VRS-CY1JF223J J 22k 1/16W M-Ox. AA R2023 VRS-CY1JF223J J 22k 1/16W M-Ox. AA R2024 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2025 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2026 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2027 VRD-MN2BE682J J 6.8k 1/8W Carbon AA R2028 VRD-MN2BE102J J 1k 1/8W Carbon AA R2029 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
(27N-S100, CN27S10/14) R2032 VRD-RA2BE103J J 10k 1/8W Carbon AA R2034 VRD-RA2BE102J J 1k 1/8W Carbon AA
(27N-S180, CN27S18) R2035 VRD-MN2BE223J J 22k 1/8W Carbon AA R2038 VRD-RA2BE103J J 10k 1/8W Carbon AA
(27N-S180, CN27S18) R2040 VRD-MN2BE102J J 1k 1/8W Carbon AA
46
Page 39
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10) PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
S2505 QSW-K0079GEZZ J CH-Up AB
PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
R2041 VRD-MN2BE333J J 33k 1/8W Carbon AA R2042 VRD-MN2BE101J J 100 1/8W Carbon AA R2043 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R2044 VRD-MN2BE682J J 6.8k 1/8W Carbon AA R2045 VRD-MN2BE101J J 100 1/8W Carbon AA R2046 VRD-RA2BE101J J 100 1/8W Carbon AB R2047 VRS-CY1JF221J J 220 1/16W M-Ox. AA R2048 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA R2060 VRD-MN2BE221J J 220 1/8W Carbon AA R2061 VRD-MN2BE562J J 5.6k 1/8W Carbon AA R2062 VRD-MN2BE183J J 18k 1/8W Carbon AA R2063 VRD-MN2BE222J J 2.2k 1/8W Carbon AA R2064 VRD-RA2BE332J J 3.3k 1/8W Carbon AA R2067 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
(CN27S10) R2068 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2069 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(27N-S100/180, CN27S14/18) R2070 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2071 VRD-RA2BE102J J 1k 1/8W Carbon AA R2101 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2102 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2201 VRD-MN2BE222J J 2.2k 1/8W Carbon AA R2202 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2203 VRS-CY1JF184J J 180k 1/16W M-Ox. AA R2211 VRD-MN2BE222J J 2.2k 1/8W Carbon AA R2212 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2213 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R2401 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2402 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2403 VRD-MN2BE101J J 100 1/8W Carbon AA R2404 VRD-MN2BE101J J 100 1/8W Carbon AA R2501 VRD-MN2BE103J J 10k 1/8W Carbon AA R2503 VRD-MN2BE273J J 27k 1/8W Carbon AA R2504 VRD-MN2BE123J J 12k 1/8W Carbon AA R2505 VRD-MN2BE563J J 56k 1/8W Carbon AA R2506 VRD-MN2BE563J J 56k 1/8W Carbon AA R2507 VRD-MN2BE823J J 82k 1/8W Carbon AA R2508 VRD-MN2BE153J J 15k 1/8W Carbon AA R2509 VRD-MN2BE272J J 2.7k 1/8W Carbon AA R2601 VRD-RA2BE331J J 330 1/8W Carbon AA R3001 VRD-RA2BE101J J 100 1/8W Carbon AB R3002 VRD-RA2BE101J J 100 1/8W Carbon AB R3003 VRS-CY1JF105J J 1M 1/16W M-Ox. AA R3004 VRS-CY1JF104J J 100k 1/16W M-Ox. AA R3005 VRS-CY1JF623J J 62k 1/16W M-Ox. AA R3007 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R3008 VRS-CY1JF302J J 3k 1/16W M-Ox. AA R3010 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA R3011 VRD-MN2BE102J J 1k 1/8W Carbon AA R3012 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R3013 VRD-MN2BE104J J 100k 1/8W Carbon AA R3014 VRD-MN2BE104J J 100k 1/8W Carbon AA R3015 VRD-RA2BE101J J 100 1/8W Carbon AB R3016 VRD-MN2BE750J J 75 1/8W Carbon AA R3017 VRD-RA2BE102J J 1k 1/8W Carbon AA R3018 VRD-RA2BE102J J 1k 1/8W Carbon AA
å RY701 RRLYJ0081CEZZ J Relay AL
å F701 QFS-B4023CEZZ J Fuse, 4A 125V AC
FB601 RBLN-0047CEZZ J Ferrite Bead AB FB702 RBLN-0036CEZZ J Ferrite Bead AB FB704 RBLN-0037CEZZ J Ferrite Bead AB FB706 RBLN-0037CEZZ J Ferrite Bead AB FH701 QFSHD1013CEZZ J Fuse Holder AC FH702 QFSHD1014CEZZ J Fuse Holder AC J931 QSOCD0430CEZZ J Socket, S-Video AE
P351 QPLGN0461CEZZ J Plug, 4-pin (S) AB P601 QPLGN0160FJZZ J Plug, 5-pin (K) AD P621 QPLGN0461CEZZ J Plug, 4-pin (YBN) AB P651 QPLGN0361CEZZ J Plug, 3-pin AB P701 QPLGN0207CEZZ J Plug, 2-pin (M) AA P703 QPLGN0269GEZZ J Plug, 2-pin (P) AB P901 QPLGN0561CEZZ J Plug, 5-pin (HA) AB P903 QPLGN0561CEZZ J Plug, 5-pin (GBN) AB P931 QPLGN0661CEZZ J Plug, 6-pin (KC) AD
P2401 QPLGN0561CEZZ J Plug, 5-pin AB SC401 QSOCN0585CEZZ Socket, 5-pin (KA) AC
SC402 QSOCN0585CEZZ Socket, 5-pin (KB) AC
RMC2601
RDA501 RDA604 RDA701 RDA751 TAN921 TAN921
QSW-K0202PEZZ or
QSW-K0202PEZZ
MISCELLANEOUS PARTS
or RRLYJ0088CEZZ or RRLYJ0094CEZZ
or QFS-B4021GEZZ
(27N-S100/180, CN27S14/18)
(27N-S100/180, CN27S14/18)
(27N-S100/180, CN27S14/18)
(27N-S100/180, CN27S14/18) RRMCU0235CEZZ J R/C Receiver AK PRDAR0234PEFW R Heat Sink, for IC501 AH PRDAR0233PEFW R Heat Sink, for Q602 AK PRDAR1008MEFW M Heat Sink, for IC701 AH PRDAR5072CEFW J Heat Sink, for IC751 AC QTANJ0323CEZZ J A V Terminal (27N-S100) AL QTANJ0523CEZZ M AV Terminal AG
(27N-S180, CN27S10/14/18) LX-BZ3049GEFD J Screw AA LX-HZ3007MEFD M Screw AA
S2501 QSW-K0079GEZZ J Power AB
SWITCHES
or QSW-K0202PEZZ
S2502 QSW-K0079GEZZ J Vol-Down AB
or QSW-K0202PEZZ
S2503 QSW-K0079GEZZ J Vol-Up AB
or QSW-K0202PEZZ
S2504 QSW-K0079GEZZ J CH-Down AB
or
47
Page 40
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-B: DUNTK9510WEK1
CRT UNIT
TRANSISTORS
Q851 VS2SC3198-Y-1 J 2SC3198(Y) AA Q852 VS2SC3789//2E M 2SC3789 AA
or
VS2SC3619LB1E Q853 VS2SC3198-Y-1 J 2SC3198(Y) AA Q854 VS2SC3789//2E M 2SC3789 AA
or
VS2SC3619LB1E Q855 VS2SC3198-Y-1 J 2SC3198(Y) AA Q856 VS2SC3789//2E M 2SC3789 AA
or
VS2SC3619LB1E Q881 VS2SA1266-Y-1 J 2SA1266(Y) AA
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D881 VHD1SS119//-1 J Diode AB D882 VHD1SS119//-1 J Diode AB D884 VHD1SS119//-1 J Diode AB
COIL
L851 VP-MK820K0000 J Peaking 82µH AB
CAPACITORS
[EL.··· Electrolytic]
C851 VCCSPA1HL391J J 390p 50V Ceramic AA C852 VCCSPA1HL331J J 330p 50V Ceramic AA C853 VCCSPA1HL391J J 390p 50V Ceramic AA C854 RC-KZ0024CEZZ J 0.001 2kV Ceramic AC
or
VCKYPB3DE472Z 0.00472kV Ceramic C883 VCEA0A1HW106M J 10 50V EL. AB
RESISTORS
[M-Ox.··· Metal Oxide]
R851 VRD-RA2BE470J J 47 1/8W Carbon AA R852 VRD-RA2BE181J J 180 1/8W Carbon AA R853 VRD-RA2BE121J J 120 1/8W Carbon AA R855 VRD-RA2BE471J J 470 1/8W Carbon AA R856 VRD-RA2BE221J J 220 1/8W Carbon AA
å R857 VRS-VV3LB123J J 12k 3W M-Ox. AB
R858 VRD-RM2HD222J J 2.2k 1/2W Carbon AA R859 VRD-RA2BE470J J 47 1/8W Carbon AA R860 VRD-RA2BE181J J 180 1/8W Carbon AA R861 VRD-RA2BE121J J 120 1/8W Carbon AA R863 VRD-RA2BE471J J 470 1/8W Carbon AA R864 VRD-RA2BE221J J 220 1/8W Carbon AA
å R865 VRS-VV3LB123J J 12k 3W M-Ox. AB
R866 VRD-RM2HD222J J 2.2k 1/2W Carbon AA R867 VRD-RA2BE470J J 47 1/8W Carbon AA R868 VRD-RA2BE181J J 180 1/8W Carbon AA R869 VRD-RA2BE121J J 120 1/8W Carbon AA R871 VRD-RA2BE471J J 470 1/8W Carbon AA R872 VRD-RA2BE221J J 220 1/8W Carbon AA
å R873 VRS-VV3LB123J J 12k 3W M-Ox. AB
R874 VRD-RM2HD222J J 2.2k 1/2W Carbon AA R881 VRD-RA2BE102J J 1k 1/8W Carbon AA R882 VRD-RA2BE331J J 330 1/8W Carbon AA R883 VRD-RA2BE561J J 560 1/8W Carbon AA R884 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R895 VRD-RA2BE470J J 47 1/8W Carbon AA
MISCELLANEOUS PARTS
P851 QPLGN0541CEZZ J Plug, 5-pin (GBN) AB P852 QPLGN0441CEZZ J Plug, 4-pin (YBN) AB SC851 QSOCV0937CEZZ M CRT Socket AF
PWB-K: DUNTKA114WEK0 (27N-S100, CN27S14)
S-VIDEO UNIT
INTEGRATED CIRCUIT
IC1501 VHiM52055FP-1 J M52055FP AH
TRANSISTORS
You can substitute "VS2SD601AR/-1" for "VS2SC2412KQ-1".
Q1501 VS2SC2412KQ-1 J 2SC2412K AA Q1502 VS2SB709AR/-1 J 2SB709AR AC
or
VS2SA1037KR-1 Q1503 VS2SC2412KQ-1 J 2SC2412K AA Q1504 VS2SC2412KQ-1 J 2SC2412K AA
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D1501 VHD1SS119//-1 J Diode AB D1502 VHD1SS119//-1 J Diode AB D1503 RH-EX0631GEZZ J Zener Diode, 9V AA D1504 RH-EX0631GEZZ J Zener Diode, 9V AA
COILS
L1501 VP-XF6R8K0000 J Peaking 6.8µH AB L1502 VP-XF6R8K0000 J Peaking 6.8µH AB L1503 VP-XF8R2K0000 J Peaking 8.2µH AB
CAPACITORS
[EL.··· Electrolytic]
C1501 VCEA0A1CW106M J 10 16V EL. AB C1502 VCCCCY1HH470J J 47p 50V Ceramic AA C1503 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1504 VCCCCY1HH271J J 270p 50V Ceramic AA C1505 VCCCCY1HH330J J 33p 50V Ceramic AA C1506 VCCCCY1HH151J J 150p 50V Ceramic AA C1507 VCCCCY1HH330J J 33p 50V Ceramic AA C1508 VCE9GA1CW106M J 10 16V EL. (N.P) AB C1509 VCEA0A1CW106M J 10 16V EL. AB C1510 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1511 VCEA0A1CW106M J 10 16V EL. AB C1512 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1513 VCKYCY1HF103Z J 0.01 50V Ceramic AA
RESISTORS
[M-Ox.··· Metal Oxide]
R1501 VRS-CY1JF223J J 22k 1/16W M-Ox. AA R1502 VRS-CY1JF123J J 12k 1/16W M-Ox. AA R1503 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA R1504 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1505 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA R1506 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1507 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1508 VRS-CY1JF561J J 560 1/16W M-Ox. AA R1509 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1510 VRS-CY1JF181J J 180 1/16W M-Ox. AA R1511 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA R1512 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R1513 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA R1514 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1515 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1516 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R1517 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1518 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1519 VRS-CY1JF101J J 100 1/16W M-Ox. AA
MISCELLANEOUS PARTS
P1501 QPLGN0585CEZZ J Plug, 5-pin (KA) AB P1502 QPLGN0585CEZZ J Plug, 5-pin (KB) AD P1503 QPLGN0661CEZZ J Plug, 6-pin (KC) AD
48
Page 41
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-K: DUNTKA115WEK0 (27N-S180, CN27S18)
DIGICOM/S-VIDEO UNIT
INTEGRATED CIRCUIT
IC1401 VHiTC90A45F-1 J TC90A45F AM IC1403 VHiKA78L05B-1 J KIA78L05BP AE IC1451 VHiM52055FP-1 J M52055FP AH
TRANSISTORS
You can substitute "VS2SD601AR/-1" for "VS2SC2412KQ-1".
Q1401 VS2SC2412KQ-1 J 2SC2412K AA Q1402 VS2SC2412KQ-1 J 2SC2412K AA Q1403 VS2SC2412KQ-1 J 2SC2412K AA Q1404 VS2SC2412KQ-1 J 2SC2412K AA Q1405 VS2SC2412KQ-1 J 2SC2412K AA Q1406 VS2SC2412KQ-1 J 2SC2412K AA Q1407 VS2SC2412KQ-1 J 2SC2412K AA
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D1401 VHD1SS119//-1 J Diode AB D1402 VHD1SS119//-1 J Diode AB D1403 VHD1SS119//-1 J Diode AB D1451 VHD1SS119//-1 J Diode AB D1452 VHD1SS119//-1 J Diode AB D1453 RH-EX0631GEZZ J Zener Diode, 9V AA D1454 RH-EX0631GEZZ J Zener Diode, 9V AA
COILS
L1401 VP-XF100K0000 J Coil 10µH AB L1402 VP-XF100K0000 J Coil 10µH AB L1403 VP-XF150K0000 J Coil 15µH AB L1405 VP-XF330K0000 J Coil 33µH AB L1406 VP-XF100K0000 J Coil 10µH AB
R1404 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1405 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA R1406 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1407 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1408 VRS-CY1JF821J J 820 1/16W M-Ox. AA R1409 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1410 VRS-CY1JF681J J 680 1/16W M-Ox. AA R1411 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1412 VRS-CY1JF821J J 820 1/16W M-Ox. AA R1413 VRS-CY1JF471J J 470 1/16W M-Ox. AA R1414 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1415 VRS-CY1JF821J J 820 1/16W M-Ox. AA R1416 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA R1417 VRS-CY1JF273J J 27k 1/16W M-Ox. AA R1418 VRS-CY1JF153J J 15k 1/16W M-Ox. AA R1419 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1420 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R1421 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA R1422 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1425 VRS-CY1JF471J J 470 1/16W M-Ox. AA R1451 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1452 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1453 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R1454 VRS-CY1JF102J J 1k 1/16W M-Ox. AA R1455 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
MISCELLANEOUS PARTS
P1401 QPLGN0585CEZZ J Plug, 5-pin (KA) AA P1402 QPLGN0585CEZZ J Plug, 5-pin (KB) AA P1451 QPLGN0661CEZZ J Plug, 6-pin (KC) AA
CAPACITORS
C1401 VCCCCY1HH220J J 22p 50V Ceramic AA C1402 VCFYSA1HB474J J 0.47 50V Mylar AC C1403 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1404 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1405 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1406 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1407 VCKYCY1CB104K J 0.1 16V Ceramic AB C1408 VCEA0A1HW106M J 10 50V EL. AB C1409 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1410 VCCCCY1HH181J J 180p 50V Ceramic AA C1411 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1412 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1413 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1415 VCEA0A1CW476M J 47 16V EL. AB C1416 VCKYCY1CB104K J 0.1 16V Ceramic AB C1417 VCCCCY1HH390J J 39p 50V Ceramic AA C1418 VCEA0A1HW106M J 10 50V EL. AB C1419 VCEA0A1HW106M J 10 50V EL. AB C1420 VCKYCY1HB103K J 0.01 50V Ceramic AA C1421 VCCCCY1HH120J J 12p 50V Ceramic AA C1423 VCCCCY1HH120J J 12p 50V Ceramic AA C1424 VCKYCY1CB104K J 0.1 16V Ceramic AB C1425 VCKYCY1CB104K J 0.1 16V Ceramic AB C1426 VCKYCY1HB102K J 1000p 50V Ceramic AA C1427 VCE9GA1CW106M J 10 16V EL. (N.P) AB C1428 VCCCCY1HH270J J 27p 50V Ceramic AA C1451 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1452 VCEA0A1CW106M J 10 16V EL. AB C1453 VCKYCY1HF103Z J 0.01 50V Ceramic AA C1454 VCKYCY1HB103K J 0.01 50V Ceramic AA C1455 VCE9GA1CW106M J 10 16V EL. (N.P) AB
[EL.··· Electrolytic]
RESISTORS
[M-Ox.··· Metal Oxide]
R1401 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1402 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1403 VRS-CY1JF182J J 1.8k 1/16W M-Ox. AA
49
Page 42
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-H: DUNTK9310WEK1
FRONT A V UNIT
J1001 QJAKE0053GEZZ J Jack, Video in AD J1002 QJAKE0055GEZZ J Jack, Audio in (L) AD J1003 QJAKE0059GEZZ J Jack, Audio in (R) AC P1001 QPLGN0541CEZZ J Plug, 5-pin (HA) AB
MISCELLANEOUS P ARTS
MISCELLANEOUS PARTS
å
ACC701
QACCD3065CESA M AC Cord AG QCNW-0130MEZZ M Connecting Cord AF QCNW-0134MEZZ M Connecting Cord AE QCNW-0166MEZZ M Connecting Cord AD QCNW-0167MEZZ M Connecting Cord AC QCNW-0252MEZZ M Connecting Cord AH
SP1 VSP0080PBL4YS M Speaker, (L) AG
or VSP0080PBK9YA
SP2 VSP0080PBL4YS M Speaker, (R) AG
or VSP0080PBK9YA
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC0658MEZZ –
SPAKC0662MEZZ –
SPAKX0165MEZZ – Buffer Material
SSAKA0004MEZZ – Polyethylene Bag
SPAKP0032MEZZ – Polyethylene Sheet
Packing Case (27N-S100/180) Packing Case (CN27S10/14/18)
— —
CABINET PARTS
1 CCABA1325MES0 M Front Cabinet Ass'y BF 1-1 1-2 GCOVA1033MEKA M Cover for R/C AD 1-3 HBDGB1009MESA M Badge, "SHARP" AD 1-4 JBTN-1096MEKA M Button, Power, Vol-up/downAD 1-5 JBTN-1097MEKA M Button, Ch-up/down AD 2 GCABB1157MEKA M Rear Cabinet (27N-S100) AY 2 GCABB1148MEKA M Rear Cabinet
1 CCABA1325MES0 M Front Cabinet Ass'y BF 1-1 1-2 GCOVA1033MEKA M Cover for R/C AD 1-3 HBDGB1009MESA M Badge, "SHARP" AD 1-4 JBTN-1096MEKA M Button, Power, Vol-up/downAD 1-5 JBTN-1097MEKA M Button, Ch-up/down AD 2 GCABB1158MEKA M Rear Cabinet AY
27N-S100, CN27S10/14
Not Available
– Front Cabinet
27N-S180, CN27S18
Not Available
– Front Cabinet
(CN27S10/14)
AZ
SUPPLIED ACCESORRIES
TiNS-6930MEZZ M Operation Manual AD
(27N-S100/180)
TiNS-6935MEN1 M Operation Manual AD
(CN27S10/14/18)
RRMCG1324CESA M Infrared R/C Unit AQ
(27N-S100, CN27S10)
RRMCG1395CESA M Infrared R/C Unit AW
(27N-S180, CN27S14/18)
CABINET PARTS LOCATION
1
1-1
2
1-4 1-3 1-2 1-5
50
Page 43
27N-S100, 27N-S180
REAR
Use 22 staples fix the packing case.
Bar Code Label
Packing Case
Serial Number Label
MARK : Not replacement items.
Number Card
FRONT
Buffer Material
Polyethylene Sheet
Polyethylene Bag
Operation Manual Infrared R/C Unit Batteries
CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PACKING OF THE SET
51
Page 44
27N-S100, 27N-S180 CN27S10/14/18
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
TQ0883-S
Apr. 2000 Printed in Japan
MK. KG
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
52
Loading...