How it Works
Sharp
Loading...
21GT-22

Sharp 21GT-22 Service Manual

Download
Page 1
SERVICE MANUAL
SX2U121GT-22/
COLOUR TELEVISION
Chassis No. GA-1
21GT-22
MODEL
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
21GT-22
FEATURES
Ë
PAL B/G
Ë
NTSC(A V Thru)
Ë
Full Auto Channel Preset and Auto Channel Skip
Ë
100 CH Program Memory
Ë
CATV (Hyper Band) Ready
Ë
AVL (Sound Keeper) Function
Ë
High Contrast Picture (Black Stretch Circuit)
Ë
ON Timer/Sleep T imer/Reminder Timer
Ë
Favourite Channel
Ë
Blue Back Noise Mute
Ë
Front AV In (Front AV Priority)
Ë
Rear A V In/Out Terminals
Ë
Colour-Comb Filter (NTSC AV In)
Ë
Hotel Mode
Ë
Front Headphone Jack
Ë
English/Thai Language OSD
Ë
Mono Bilingual
CONTENTS
Page
» SPECIFICATIONS .............................................2
» IMPORTANT SERVICE NOTES ........................ 2
» ADJUSTMENT PRECAUTIONS........................3
» MEMORY MAP ................................................ 11
» GA1 HOTEL MODE APPLICATION ................15
» TROUBLE SHOOTING TABLE........................15
» SOLID STA TE DEVICE BASE DIAGRAM .......18
» WAVEFORMS ..................................................19
» CHASSIS LAYOUT..........................................20
» BLOCK DIAGRAM...........................................21
» DESCRIPTION OF SCHEMATIC DIAGRAM ..25 » SCHEMATIC DIAGRAM
Ë
MAIN UNIT ...................................................26
Ë
CRT UNIT.....................................................28
Ë
HEADPHONE UNIT ..................................... 28
Ë
MONO BILINGUAL UNIT.............................29
» PRINTED WIRING BOARD ASSEMBLIES..... 30
» REPLACEMENT PARTS LIST
Ë
ELECTRICAL PARTS
MAIN UNIT ................................................... 36
CRT UNIT.....................................................39
HEADPHONE UNIT ..................................... 39
MONO BILINGUAL UNIT.............................39
Ë
SUPPLIED ACCESSORIES.........................40
Ë
PACKING PARTS.........................................40
Ë
CABINET PA RTS .........................................41
» PACKING OF THE SET...................................42
Page
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user – serviceable parts inside. Refer servicing to qualified service personnel.
WARNING
SHARP CORPORATION
1
Page 2
21GT-22
qualified service personnel only.
IMPORTANT SERVICE NOTES
Maintenance and repair of this receiver should be done by
SERVICING OF HIGH VOLTAGE SYSTEM AND
PICTURE TUBE
When servicing the high voltage system, remove static charge from it by
connecting a 10k ohm Resistor in series with an insulated wire (such as a
test probe) between picture tube dag and 2nd anode lead. (AC line cord
should be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion protection.
discharging the high voltage completely
2. Replace with tube of the same type number for continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after
X-RAY
This receiver is designed so that any X-Ray radiation is kept to an absolute
minimum. Since certain malfunctions or servicing may produce potentially
than 28.0 kV (at beam 0
hazardous radiation with prolonged exposure at close range, the following
precautions should be observed:
1. When repairing the circuit, be sure not to increase the high voltage to more
Depth: 477.5 mm
Height: 476.0 mm
Weight (Approx.): 20.5 kg
2-1 2-2
SPECIFICATIONS
5.74 MHz ...................................................................................................... 33.16 MHz
5.5 MHz .......................................................................................................... 33.4 MHz
Picture IF Carrier ...............................................................................................38.9 MHz
Sound IF Carrier Frequency
Convergence .................................................................................Self Converging System
Focus ......................................................................... Electr ostatic Focus High Bi -Potenti al
Sweep Deflection................................................................................................... Magnetic
Intermediate Frequencies
Colour Sub-Carrier Frequency ....................................................................... 34.47 MHz
Power Input.................................................................................... AC110 - 240V, 50/60 Hz
Power Consumption .....................................................................................................84 W
Size .............................................................................................. 5 × 9 cm Elliptic (2 pcs)
Audio Power Output Rating......................................................................... 5.0 W (at Max.)
Speaker
VHF/UHF....................................................................................... 75 ohm Unbalanced
Voice Coil Impedance......................................................................... 16 ohms at 400 Hz
Aerial Input Impedance
» VHF..................................................................................................... E2 thru E12
Receiving Channels (PAL-B/G)
» UHF .................................................................................................. E21 thru E69
» VHF-Channels.................................................................... 48.25 thru 463.25 MHz
» UHF-Channels ................................................................. 471.25 thru 863.25 MHz
Receiving Frequency
Dimensions ..............................................................................................Width: 506.5 mm
2
Specifications are subject to change without prior notice.
Cabinet Material ................................................................................................. All Plastics
Page 3
SUB
ADJ.
MODE
21GT-22
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
SUB
ADJ.
MODE
Y-DELAY
ADJ.
MODE
OFFSET
ADJ.
MODE
↓
WHITE POINT
AGC &
SERVICE MODE
Ë
(1)In the Service Mode, Key is used to select the mode in the following order.
ADJ.
MODE
MODE
GEOMETRIC
IC
OPTION
MISC.
OPTION
MODE
MODE
FORWARD : CH DOWN KEY
REVERSE : CH UP KEY
WHITE POINT
AGC &
MAX VOLUME (SUB-VOL)
↓
ADJ.
MODE
W.P RED STD. W.T. (DRI-RS)
↓
MODE
GEOMETRIC
AGC TAKE OVER POINT (AGC)
SUB TINT (SUB-TINT)
SUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)
SUB BRIGHTNESS (SUB-BRI)
↓
↓
↓
↓
W.P.BLUE STD. W.T. (DRI-BS)
W.P. RED COOL W.T.(DRI-RC)
W.P. GREEN STD. W.T.(DRI-GS)
↓
↓
↓
↓
VERTICAL AMP (V-AMP)
VERTICAL SLOPE (V-LIN)
VERTICAL SHIFT (V-CENT)
MAX HOTEL VOLUME (HTL-VOL)
SUB SHARPNESS (SUB-SHP)
↓
↓
W.P. RED W ARM W.T.(DRI-RW)
W.P. BLUE COOL W.T.(DRI-BC)
W.P. GREEN COOL W.T.(DRI-GC)
↓
↓
EAST-WEST WIDTH (H-SIZE)
HORIZONTAL PARALLELOGRAM (EW//)
HORIZONTAL SHIFT (H-CENT)
BLACK LEVEL OFFSET R(CUT-R)
HOTEL PROGRAM NO(HTL-PRG)
↓
↓
W.P. GREEN W ARM W.T.(DRI-GW)
↓
↓
EAST-WEST PARABOLA/WIDTH (PARA)
BLACK LEVEL OFFSET G(CUT-G)
OSD RGB REFERENCE (RGB)
W.P. BLUE W ARM W.T. (DRI-BW)
↓
EAST-WEST UPPER COR. PB (COR(U))
CATHODE DRIVE LEVEL(CDL)
↓
↓
↓
HORIZONTAL BOW (HB)
EAST WEST TRAPEZIUM (TRAPE)
EAST-WEST LOWER COR. PB (COR(L))
S-CORRECTION (S-COR)
FORWARD : CH DOWN KEY
REVERSE : CH UP KEY
* ( ) means OSD display.
C bus con-
2
C bus control and in the
2
C bus control include preset-only
2
ADJUSTMENT PRECAUTIONS
adjustment.
position and the microprocessor is in input mode. (Adjustment through the I
trol). (Use JWS Key to set as well).
one by one.
one by one.
(OFF) position and the microprocessor is in out of the service mode.
1 Make a short-circuit 137 and 138 for a second and release to switch to the service mode
2 Press the CH DOWN / UP key on the remote controller to get ready to select the mode
3 Press the CH DOWN / UP key on the remote controller to select the modes reversibly
4 Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.
5 Make a short-circuit 137 and 138 for a second and release to switch to the normal mode
This model’s setting are adjusted in two different ways: though the I
conventional analog manner. The adjustments via the I
items and variable data.
CAUTION : Make sure TV Set is in "Normal Condition" before switch to Service Mode for
1. Setting the service mode by the microprocessor.
3-1 3-2
switch to Service Mode. Initial values are automatically preset, only when a new EEPROM
is used (Judge with the first 4 bytes).
1 Make a short-circuit JA137 and JA138, then turn ON the main power and release to
2 The initial data are preset as listed in pages 4-6.
2. Factory Presetting.
FIRST TIME, make sure to make a short-circuit 137 and 138 switch to the service
mode position first and then turn on the main power switch. (See 2-1 above).
Precaution: If haven’t done this initiation, it may possibly generate excessive Beam
current.
3 Make sure the data need modify or not (Initial data).
Note: Once the chassis has been assembly together and ready to be POWER ON for the
(GA1 Series type RH-iX3368CE)
3. For reference please check with memory map
3
Page 4
21GT-22
FUNCTION AGC
RC COMMAND SERVICE-ITEM
CONTRAST DOWN V-LIN
COLOUR DOWN V-AMP
BRIGHTNESS DOWN V-CENT
TINT DOWN H-CENT
SHARPNESS DOWN EW / /
SYSTEM HB
BLUEBACK S-COR
CONTRAST UP SUB-CON
TIMER SUB-VOL
Direct Key-in for Service Item in Service Mode.
↓
↓
↓
↓
↓
↓
IC
MODE
OPTION
ADJ.
MODE
OFFSET
↓
BLACK STRETCH (BKS)
FAST FILTER IF-PLL(FFI)
AUTO V OLUME LEVELING(A VL)
VERTICAL SCAN DISABLE(VSD)
↓
↓
↓
ENABLE VERTICAL GUARD (EVG)
↓
↓
↓
↓
AUTO COLOUR LIMIT(ACL)
EHT TRACKING MODE (EHT)
↓
↓
FORCED COLOUR LIMIT(FCO)
OVERSCAN SWITCH OFF(OSO)
↓
TINT UP SUB TINT
COLOUR UP SUB-COL
BRIGHTNESS UP SUB-BRI
CHANNEL 1 DRI-GS
CHANNEL 4 DRI-BS
SHARPNESS UP SUB-SHP
B
A
CHANNEL 7 CUT-R
↓
BILINGUAL(BIL)
↓
CHANNEL FLASHBACK CUT-G
↓
IF AGC SPEED BIT 0 (AGC0)↓IF AGC SPEED BIT 1 (AGC1)
↓
↓
↓
↓
↓
↓
↓
↓
LED BLINK SPEED (LED-F)
FOA Time Constant-AV (FOA-AV)
FOA Time Constant-RF (FOA-FE)
↓
↓
↓
FOB Time Constant-AV (FOB-AV)
FOB Time Constant-RF (FOB-FE)
↓
↓
↓
VOLUME CONTROL TABLE (MSA)
OUTPUT VERTICAL GUARD (NDF)
↓
↓
↓
↓
↓
↓
B
4-1 4-2
COLOUR OFFSET (PAL) (COL-OP)
COLOUR OFFSET (SECAM) (COL-OS)
↓
↓
MODE
Y-D TIME FOR PAL (TV) (DL-PT)
↓
Y-D TIME FOR SECAM (TV) (DL-ST)
ADJ.
Y-DELAY
SHARPNESS OFFSET (PAL) (SHP-OP)
COLOUR OFFSET (NTSC358) (COL-O3)
COLOUR OFFSET (NTSC443) (COL-O4)
SHARPNESS OFFSET (SECAM) (SHP-OS)
SHARPNESS OFFSET (NTSC358) (SHP-O3)
SHARPNESS OFFSET (NTSC443) (SHP-O4)
↓
↓
↓
↓
↓
↓
Y-D TIME FOR PAL (AV) (DL-PA)
Y-D TIME FOR B/W (TV) (DL-TV)
Y-D TIME FOR N358 (TV) (DL-3T)
Y-D TIME FOR N443 (TV) (DL-4T)
Y-D TIME FOR N358 (AV) (DL-3A)
Y-D TIME FOR SECAM (AV) (DL-SA)
↓
*(Y-D : Y-DELAY)
Y-D TIME FOR B/W (AV) (DL-AV)
Y-D TIME FOR N443(AV) (DL-4A)
MISC.
OPTION
SOUND MUTE BIT 0 (SM0)
FM WINDOW SELECTION (FMWS)
NUMBER OF EXT AV SOURCE (AV)
↓
↓
MODE
↓
SOUND SYSTEM I (S-I)
SOUND SYSTEM M (S-M)
SOUND SYSTEM DK (S-DK)
4
THAI LANGUAGE (THA)
SOUND MUTE BIT 1 (SM1)
↓
↓
SOUND SYSTEM BG (S-BG)
MALAY LANGUAGE (MAL)
ARABIC LANGUAGE (ARA)
CHINESE LANGUAGE (CHI)
↓
↓
↓
↓
FE (RF) SECAM (F-SECAM)
FE (RF) NTSC 3.58 (F-N358)
FE (RF) NTSC 4.43 (F-N443)
PLAYBACK SECAM (P-SECAM)
FRENCH LANGUAGE (FRE)
↓
VIDEO MUTE AT IDENT LOSS (VMI)
SYNC OF OSD (HP2)
RUSSIAN LANGUAGE (RUS)
FORCED V-SYNC SLICING LEVEL(FSL)
↓
↓
HOTEL MODE (HTL)
/SOURCE CHANGE (VMC)
VIDEO MUTE AT PROGRAM
REDUCED FM DEMODULATION
GAIN FOR BTSC SIGNAL (BTSC)
TUNER SELECTION (CPT)
↓
A
Page 5
REMARK
INITIAL DATA FIX/ADJ
0*FIX
1*FIX
1*FIX
0*FIX
1*FIX
1*FIX
0*FIX
0*FIX
0*FIX
0*FIX
1 (0) *FIX
1*FIX
1 (0) *FIX
1 (0) *FIX
0*FIX
1*FIX
1 (0) *FIX
1 (0) *FIX
1*FIX
0*FIX
0*FIX
0*FIX
1*FIX
1 (0) *FIX
0*FIX
0 (1) *FIX
1 (0) *FIX
1 (0) *FIX
1 (0) *FIX
1 (0) *FIX
1 (0) *FIX
*FIX
0*FIX
0*FIX
*FIX
1*FIX
0*FIX
0*FIX
0*FIX
1*FIX
1*FIX
0 (1) *FIX
0 (1) *FIX
21GT-22
0 (1) *FIX
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
EEPROM ITEMS OSD DATA LENGTH
SHARPNESS OFFSET (NTSC358) SHP-O3 0~15 12 *FIX
SHARPNESS OFFSET (NTSC443) SHP-O4 0~15 8 *FIX
VERTICAL SCAN DISABLE VSD
BLACK STRETCH BKS
PROM
2
PROM.
2
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
AUTOMATIC VOLUME LEVELING AVL
FAST FILTER IF-PLL FFI
ENABLE VERTICAL GUARD (RGB BLANKING) EVG
EHT TRACKING MODE (HCO) EHT
OVERSCAN SWITCH OFF OSO
AUTO COLOUR LIMIT ACL
FORCED COLOUR LIMIT FCO
SOUND SYSTEM M S-M
SOUND SYSTEM DK S-DK
SOUND SYSTEM I S-I
REMARK
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
VMC
BTSC
SOUND SYSTEM BG S-BG
PLAYBACK SECAM P-SECAM
FE (RF) NTSC 3.58 F-N358
FE (RF) NTSC 4.43 F-N443
FE (RF) SECAM F-SECAM
VIDEO MUTE AT IDENT LOSS VMI
VIDEO MUTE AT PROGRAM/SOURCE CHANGE
HOTEL MODE HTL
REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL
0 FOR1 AV/1 FOR 2AV
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
NUMBER OF EXTERNAL AV SOURCE AV
FM WINDOW SELECTION FMWS
SOUND MUTE BIT 0 SM0
SOUND MUTE BIT 1 SM1
THAI LANGUAGE THA
ARABIC LANGUAGE ARA
MALAY LANGUAGE MAL
CHINESE LANGUAGE CHI
FRENCH LANGUAGE FRE
SAME AS (DRI-BS) DATA
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE) 0 (1)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
RUSSIAN LANGUAGE RUS
FORCED V-SYNC SLICING LEVEL FSL
SYNC OF OSD HP2
TUNER SELECTION (0:SHARP/ALPS;1:MURATA) CPT 0(DISABLE)/1(ENABLE) 0 (1)
BILINGUAL BIL
IF AGC SPEED BIT 0 AGC0
IF AGC SPEED BIT 1 AGC1
PHI-1 TIME CONSTANT (RF) FOA-FE
PHI-1 TIME CONSTANT (RF) FOB-FE
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
0(DISABLE)/1(ENABLE)
Please set the EEPROM initial data according to the value in parenthesis ( ) before adjustment.
1) *FIX: PLEASE DO NOT CHANGE FIXED DATA WITHOUT SPECIFIC INSTRUCTION.
2) *2: CDL ADJUST = 7
PHI-1 TIME CONSTANT (OFF AIR) FOA-AV
PHI-1 TIME CONSTANT (OFF AIR) FOB-AV
LED BLINK SPEED LED_F
VOLUME CONTROL PWM TABLE MSA
OUTPUT VERTICAL GUARD NDF
NOTE :
STEPS.
NEW SUB-COL=SUB-COL DATA OF 75% WHITE & RED PORTIONS AT SAME LEVEL +6
4) *4: After SUB-COLOUR ADJUSTMENT, ADD 6 STEPS INTO THE DATA OF SUB-COL.
3) *3: S-COR ADJUST = 20
INITIAL DATA FIX/ADJ
EEPROM ITEMS OSD DATA LENGTH
00H : 55H 02H : 43H
01H : 4FH 03H : A1H
Address : Data Address : Data
AGC TAKE OVER POINT AGC 0~63 14 ADJ
VERTICAL SLOPE V-LIN 0~63 32 ADJ
VERTICAL AMPLITUDE V-AMP 0~63 32 ADJ
VERTICAL SHIFT V-CENT 0~63 32 ADJ
HORIZONTAL SHIFT H-CENT 0~63 32 ADJ
EAST-WEST WIDTH H-SIZE 0~63 32 *FIX
HORIZONTAL PARALLELOGRAM EW// 0~63 32 *FIX
After short JA137 & 138, and turn on the main power switch, read data from E
address 00H ~ 03H, and compare to the list below, if different, initialize the E
EAST-WEST PARABOLA/WIDTH PARA 0~63 32 *FIX
EAST-WEST UPPER CORNER PARABOLA COR (U) 0~63 32 *FIX
EAST-WEST LOWER CORNER PARABOLA COR (L) 0~63 32 *FIX
EAST-WEST TRAPEZIUM TRAPE 0~63 32 *FIX
HORIZONTAL BOW HB 0~63 32 *FIX
255 *FIX
SHARPNESS OFFSET (PAL) SHP-OP 0~15 8 *FIX
5-1 5-2
SHARPNESS OFFSET (SECAM) SHP-OS 0~15 4 *FIX
0~99 OR>99FOR NONE
S-CORRECTION S-COR 0~63 0 ADJ *3
WHITE POINT RED STD WHITE TEMP DRI-RS 0~63 32 *FIX
WHITE POINT GREEN STD WHITE TEMP DRI-GS 0~63 32 ADJ
WHITE POINT BLUE STD WHITE TEMP DRI-BS 0~63 32 ADJ
WHITE POINT RED COOL WHITE TEMP DRI-RC 0~63 25 *FIX
WHITE POINT GREEN COOL WHITE TEMP DRI-GC 0~63 32 ADJ (DRI-GS)- 7 DATA
WHITE POINT BLUE COOL WHITE TEMP DRI-BC 0~63 32 ADJ
WHITE POINT RED WARM WHITE TEMP DRI-RW 0~63 32 *FIX
WHITE POINT GREEN WARM WHITE TEMP DRI-GW 0~63 32 ADJ (DRI-GS)-7 DATA
WHITE POINT BLUE WARM WHITE TEMP DRI-BW 0~63 32 ADJ (DRI-BS)-7 DATA
MAX VOLUME SUB-VOL 0~63 63 *FIX
SUB CONTRAST SUB-CON 0~63 63 *FIX
SUB COLOUR SUB-COL 0~63 32 ADJ *4
SUB BRIGHTNESS SUB-BRI 0~63 32 ADJ
SUB TINT SUB-TINT 0~63 32 ADJ
SUB SHARPNESS SUB-SHP 0~63 32 (20) *FIX
MAX HOTEL VOLUME HTL-VOL 0~63 32 *FIX
HOTEL PROGRAM NUMBER HTL-PRG
OSD RGB REFERENCE RGB 0~15 15 *FIX
BLACK LEVEL OFF-SET R CUT-R 0~63 32 ADJ
BLACK LEVEL OFF-SET G CUT-G 0~63 32 ADJ
CATHODE DRIVE LEVEL CDL 0~15 0 ADJ *2
Y-DELAY TIME FOR PAL(TV) [YD] DL-PT 0~15 12 *FIX
Y-DELAY TIME FOR SECAM(TV) [YD] DL-ST 0~15 15 *FIX
Y-DELAY TIME FOR N358 (TV) [YD] DL-3T 0~15 12 *FIX
Y-DELAY TIME FOR N443 (TV) [YD] DL-4T 0~15 12 *FIX
Y-DELAY TIME FOR B/W (TV) [YD] DL-TV 0~15 12 *FIX
Y-DELAY TIME FOR PAL (AV) [YD] DL-PA 0~15 12 *FIX
Y-DELAY TIME FOR SECAM (AV) [YD] DL-SA 0~15 15 *FIX
Y-DELAY TIME FOR N358 (AV) [YD] DL-3A 0~15 12 *FIX
Y-DELAY TIME FOR N443 (AV) [YD] DL-4A 0~15 12 *FIX
Y-DELAY TIME FOR B/W (AV) [YD] DL-AV 0~15 12 *FIX
COLOUR OFFSET (PAL) COL-OP 0~15 8 *FIX
COLOUR OFFSET (SECAM) COL-OS 0~15 8 *FIX
COLOUR OFFSET (NTSC358) COL-03 0~15 4 *FIX
COLOUR OFFSET (NTSC443) COL-O4 0~15 4 *FIX
5
Page 6
21GT-22
» Bias box: About 4.5 V
Oscilloscope
0.1V
TV Set
Bias box
TP201+
+
–
–
E-9 CH
P C
10k
100k
1n60
75ohm
IF OUT
-1.5+/-0.8dB
1000p
Oscilloscope
±1 dBµV
Fig. 1
PIF ADJUSTMENT
Service Mode for adjustment.
signal, but with no signal input.
Adjust the PLL data.
to the tuner antenna. (RF SWEEP)
ANCE probe with wave detector; see Fig.1) to
the tuner's IF output terminal. (This terminal
1. Get the tuner ready to receive the E-9 CH
2. Connect the sweep generator's output cable
3. Adjust the sweep generator's to 80dBuV.
Tuner IFT
(PRESET)
ADJUSTMENT PRECAUTION:Make sure TV Set in "Normal Condition" before switch to
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
must have the probe alone connected).
4. Connect the response lead (use LOW IMPED-
5. Set the RF AGC to 0 - 6 V with no saturation
Fig. 2
For the 50 ohm signal strength
gauge, when not using 50/75
impedance adapter, signal
Note:
position during this adjustment.
with the waveform.
as shown in Fig. 2.
6. Adjust the tuner IF coil to obtain the waveform
Note:Be sure to keep the tuner cover in
» Signal Strength: 57 ±1 dBµV (75 ohm open)
1. Receive "PAL COLOUR BAR" signal.
2. Connect the oscilloscope to TP201 (Tuner’s
TAKE OVER
POINT
ADJUSTMENT
2 RF-AGC
±1 dBµV(75 ohm
open), instead of 57
(75 ohm open).
The loss of using impedance
strength is 52
AGC Terminal) as shown in Fig. 3.
C BUS
2
CONTROL)
(I
adapter
Precaution:
Fig. 3
"AGC" bus data to obtain the Tuner output
voltage level at TP201 is drop 1 step data from
maximum voltage.
3. Call "AGC" mode in service mode. Adjust the
sure that there is no cross modulation beat.
63~67dBµV , and make sure there is no noise.
4. Change the antenna input signal to
5. Turn up the input signal to 90~95 dB µV to be
PROM.
2
ITEMS DATA SETTING
SHIPPING SETTING & CHECKING
(1)The following default data has been factory-set for the E
LAST PROGRAM/CHANNEL 1
FLASHBACK PROGARM/CH 1
C-SYSTEM AUTO
S-SYSTEM B/G
VOLUME 1
AFC ON
SKIP OFF
DIGIT 1
TINT 0 (CENTER)
COLOUR 0 (CENTER)
CONTRAST 60 (MAX)
BRIGHTNESS 0 (CENTER)
ON TIMER In-active, "--:--"
SHARPNESS 0 (CENTER)
WHITE TEMP STANDARD
REMINDER TIMER In-active, "--:--"
OFF TIMER In-active, "--:--"
LANGUAGE THAI
LAST POWER POWER-ON
BLUE BACK MUTE ON
HOTEL MODE OFF
6-1 6-2
LAST TV/AV TV
0 CHANNEL SKIP ON
6
Page 7
21GT-22
BGR
BGR
CONVERGENCE ADJUSTMENT
mode.
1. Receive the "Crosshatch Pattern" signal.
2. Using the remote controller, call NORMAL
Static convergence
1. Turn the 4-pole magnet to a proper opening
RGB
RGB
RGB
Fig. a
angle in order to superpose the blue and red
colours.
angle in order to superpose the green colour
over the blue and red colours.
2. Turn the 6-pole magnet to a proper opening
Fig. b
BGR
swing the deflection coil upward.
screen in the following steps.
Dynamic convergence
1. Adjust the convergence on the fringes of the
and swing the deflection coil downward.
a) Fig. a : Drive the wedge at point "a" and
b) Fig. b : Drive the wedge at point "b" and "c"
About
100°
BGR
Fig. c
RGB
swing the deflection coil rightward.
swing the deflection coil leftward.
c) Fig. c : Drive the "c" wedge deeper and
d) Fig. d : Drive the "b" wedge deeper and
tape over them.
2. Fix all the wedges on the CRT and apply glass
Fig. d
Wedge "a"
About
magnet unit (purity, 4-pole, 6-pole magnets)
and magnet unit lock screw.
Finally received the Red-only and Blue-only
signals to make sure there is no other colours
3. Apply lacquer to the deflection yoke lock screw,
on the screen.
100°
4-pole magnet
Wedge
"c"
Lacquer
Wedge
"b"
CRT neck
6-pole magnet
20mm
Lacquer
Purity magnet
ADJ.
(To be done
after the purity
adjustment.)
1 CONVERGENCE
NO. Adjustment part Adjusting procedure and conditions Waveform and others
b
Fig. 1-1
a
PURITY ADJUSTMENT
beam current to ~ 700 µA.
coil.
2. Degauss the CRT enough with the degausing
3. Maintain the purity magnet at the zero mag-
through the microscope. Adjust the landings
netic field and keep the static convergence
to A rank requirement.
roughly adjusted.
5. Orient the raster rotation to 0 eastward.
4. Observe the points a, b, as shown in Fig. 1-1
6. Tighten up the deflection coil screws.
A = B
B
A
Fig. 1-2
Rank "A"
(on the right of the CRT)
µA.
warming up the unit for 30 minutes or
(11kgf ± 2 kgf)
» Tightening torque: 108N ± 20 N
A rank requirements. If not, stick the magnet
7. Make sure the CRT corners landing meet the
longer with a beam current over 700
sheet to correct it.
Note:This adjustment must be done after
change.
* For the following colours press R/C RGB key to
A
Red-only
Blue-only
Green-only
A = B
B
Signal-colour
screen cleared
Fig. 1-3
Rank "A"
(on the left of the CRT)
ond in NORMAL MODE, the col-
* Press R/C RGB key for 1 sec-
our will change to RGB mono
colour mode.
7-1 7-2
PURITY ADJ. 1. Receive the GREEN-ONLY signal. Adjust the 1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
7
Page 8
21GT-22
B
G Cy
Mg R
Y 100%W W
75%
Fig. 1-1
till the horizontal line in the center of
monoscope is just at the position where the
1. Receive Monoscope Pattern Signal.
blanking starts.
2. Call the "V-LIN" mode.
3. Increase or decrease "V-LIN" by Volume key
C
2
V-SLOPE (I
BUS CON-
TROL)
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
as beside procedure.
line appear and make sure the col-
our appear whether red, green or
*Alternative Procedure
(1) Step (1), (2), (3) and (4) are same
biue.
(2) Then continue adjust until retrace
till the picture is centered.
1. Call the "V-CENT" mode.
2. Increase or decrease "V-CENT" by V olume key
C BUS
2
CONTROL)
V-SHIFT-50
(I
2
test points as below which is based
on colour appear at (2) RED = TP47R,
GREEN =TP47G, BLUE = TP47B
(3) Connect the oscilloscope to related
key to set overscan of 9.5% typical.
Adjustment Spec 9.5% range +1% -0%.
1. Call the "V-AMP" mode.
2. Increase or decrease "V - AMP" by Volume
C BUS
2
V-AMP50
(I
3
3.2Vdc
of signal reach 3.2Vdc.
(4) Then adjust Screen VR until the tip
1. Call the "H-CENT" mode.
2. Increase or decrease "H-CENT" by Volume key
CONTROL)
H-SHIFT (50)
(H-CENTER)
4
t
to center the picture horizontal.
0
1
adjust V-Slope, V -Shift and V-Amp to makesure
adjustment is in acceptable Ring-Shaped.
1. SET DATA TO 20
* Check the E-5 CH Monoscope Pattern then re-
C BUS
2
S-CORREC-
TION (I
5
1 2 3 4 5
Line 3 is one step (data) brighter than line 2
CONTROL)
1 2 3 4 5
2
1. SET DATA TO 20
SUB-
SHARPNESS
6
# 12300°K X : 0.272
ing.
2. Press R/C to set Picture NORMAL condition.
3. Adjust the focus control to get the best focus-
1 Focus 1. Receive the "Monoscope Pattern" signal.
Y : 0.275
(MINOLTA COLOUR ANALYZER CA-
100)
PAL CHROMA ADJUSTMENT
1. Receive the "PAL Color Bar" signal.
2. Press R/C to set Picture Normal condition.
3. Connect the oscilloscope to
C BUS
2
CONTROL)
(I
1 SUB COLOUR
NO. Adjustment part Adjusting procedure and conditions Waveform and others
LOW HIGH
by Volume key.
*Note: Above Data can be UP/DOWN
21" 10cd/m2 120cd/m2
» Range : 20 V/div. (AC) (Using 10:1 probe)
» Sweep time : 10 µsec/div.
mode. Adjust SUB COLOUR bus data, so that
the 75% White & Red portions of PAL Color
Bar be at the same level shown as Fig. 1-1.
Red cathode(D882 Chathode) for 21" (Normal
Neck).
4. Using the R/C call "SUB COL" in SERVICE
DRI-BW="DRI-BS"-7
DRI-GC="DRI-GS"-7
DRI-RC=25
* 12300°K DRI-GW="DRI-GS"-7
COL obtained in 4.
5. Add another 6 steps up into the value of SUB-
6. Clear the SERVICE Mode.
µA.
8-1 8-2
RS/RW/RC, DRI-GS/GW/GC, DRI-BS/BW/BC,
CUT-R and CUT -G must be INITIAL DATA.
room.
NO VIDEO signal.
screen variable resistor until colour raster suddenly
on and off (AKB start function).
Remark
1. Before CRT cutoff adjustment, SUB-BRIGHT, DRI-
2. CRT Cutoff adjustment must be done inside a dark
1. Switch TV to VIDEO mode,BLUE BACK OFF, with
2. Press R/C to set Picture Normal condition.
3. First, off the screen by adjust screen variable resistor.
*4. Next, checking AKB circuit function by slowly increase
C BUS
2
CONTROL)
CRT CUTOFF
ADJUSTMENT
(I
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
until screen retrace line cut off (Not Raster)
5. Then continue adjust until retrace line appear.
6. Finally, slowly decrease the screen variable resistor
Must confirm the AKB function in set before continue
the next adjustment.
hatch pattern with 5 black level windows)
the line 1and 2 have the same darkness wherelse
line 3 is one step (data) brighter than line 2. Finally
data minus 1 to make line 1, 2, and 3 are in same
Note :
1. Call " SUB-BRI" in service mode. (Receive Cross-
2. Adjust the " SUB BRIGHT " bus data in order that
BRIGHTNESS
level (darkness).
C BUS
2
ADJUSTMENT
(I
CONTROL)
2 SUB-
TP603 (+).
1. Receive the "WHITE" pattern with BURST signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP602 (-)
BALANCE
SERVICE
3 WHITE
8
ing up the unit for 30 minutes or longer with
a beam current over 700
BS data to have a colour temperature of 12300°K (
white ). * Note .
set BRIGHTNESS Y by generator, to **10 cd/m2
(MINOLTA CA-100) by reducing LUMINATE Y sig-
nal.
perature #. Then go back NORMAL mode (HIGH
BRIGHT**) to check colour temperature.
4. Check Beam current should be around 1100 µA.
5. Set it to service mode and adjust the DRI-GS, & DRI-
6. Receive "WHITE" pattern, WITH BURST signal, and
C BUS
2
MODE ADJ.
(I
CONTROL)
If out of range, back to 1.
7. Adjust "CUT-R" & "CUT-G" to get desired colour tem-
Note:This adjustment must be done after warm-
DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED)
DRI-BC = "DRI-BS"
(For 12300° K Condition)
after finishing DRI-BS and DRI-GS DATA ADJUST-
MENT.
* Adjust DRI-GC/GW, DRI-BC/BW as following DATA,
TP602 (–).
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP603 (+) &
beam check
4 Max.
Beam current must be within 1100 ± 100 µA.
(Full Scale: 3 mA Range)
4.
Page 9
21GT-22
the CONTRAST effect is OK or not.
1. Receive "Monoscope Pattern" signal.
2. Set P-Mode to select CONTRAST.
3. Press V olume Up/Down key to check whether
CONTRAST
key
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
SAME LEVEL
the COLOUR effect is OK or not.
2. Set P-Mode to select COLOUR.
3. Press Volume Up/Down key to check whether
2 COLOUR key 1. Receive "Colour Bar" signal.
B
Cy G Mg R Y
W
the BRIGHTNESS effect is OK or not
1. Receive "Monoscope Pattern" signal.
2. Set P-Mode to select BRIGHTNESS.
3. Press Volume Up/Down key to check whether
key
3 BRIGHTNESS
Fig. 1-1
in.
for GREEN direction and DOWN for PURPLE
direction whether is OK or not.
2. Set P-Mode to select TINT.
3. Press Volume Up/Down key to check TINT, UP
4 TINT key 1. Receive the "NTSC Colour Bar" signal thru AV
each short test.
* Select one of Q883/5/7 to do
1. Receive "Monoscope Pattern" signal.
2. Set P-mode to select SHARPNESS.
3. Press Volume Up/Down key to check whether
Key
5 SHARPNESS
the SHARPNESS effect is OK or not.
channel number in green colour under AFT ON
condition.
1. All Ch (1~99) will have an OSD display of the
COLOUR
6 CH DISPLAY
7 NORMAL Key 1. Once in PICTURE Mode, and the NORMAL
key is pressed, all the settings will be present
to normal setting.
(Normal setting value for every mode).
» CONTRAST : MAX
» COLOUR : CENTER
» BRIGHTNESS : CENTER
» TINT : CENTER
» SHARPNESS : CENTER
TEMP Option, STANDARD:
NORMAL SETTING, WARM for more
2. Set FUNCTION to select WHITE TEMP.
8 White Temp 1. Receive "Monoscope Pattern" signal.
REDDISH direction changing, COOL for more
3. Press Volume Up/Down key to check WHITE
BLUISH direction changing.
9-1 9-2
Range : 100mV/div. (AC) (Use Probe 10:1)
Sweep time: 10 µsec/div.
»
Adjust the "SUB-TINT" bus data to obtain the
AV in.
5) BLUE-OUT.
NTSC CHROMA ADJUSTMENT
1. Receive the "NTSC3.58 Colour Bar" signal thru
1 SUB-TINT
NO. Adjustment part Adjusting procedure and conditions Waveform and others
»
2. Connect the oscilloscope to TP47B (P882 pin
C BUS
2
(I
CONTROL)
waveform shown as Fig. 1-1.
3. Call the "SUB-TINT" mode in service mode.
4. Clear the SERVICE mode.
short, make sure the protector ON and switch
1. Receive "Monoscope Pattern" signal.
2. Set CONTRAST MAX.
to standby mode.
3. Set BRIGHT MAX.
4. During the Collector & Emitter of Q883/5/7
PROTECTOR OPERATION CHECKING
PROTECTOR
1 BEAM
NO. Adjustment part Adjusting procedure and conditions Waveform and others
(R610 side).
the protector is not work.
the protector is work.
testing in +B line, check all possible damaged
components on +B line.
1. Receive "Monoscope Pattern" signal.
2. Connect output of Bias Box to D603 cathode
3. Set voltage of Bias Box to 18V and make sure
4. Set voltage of Bias Box to 27V , and make sure
(Use random selected set for inspection)
1. Once finish rectified Electrolytic Capacitor short
A/V INPUT AND OUTPUT CHECKING
PROTECTOR
2 H.V
protectors
3 Other
9
White Color Bar, Sound 400 Hz 100% Mod).
pedance. Make sure the output is as specified
(1.0 Vp-p ±3 dB).
1. Receive the "PAL Color Bar" signal (100%
2. Terminate the Video output with a 75 ohm im-
VIDEO AND
AUDIO OUT-
PUT CHECK
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
pedance. Make sure the O/P is as specified
3. T erminate the Audio output with a 10k ohm im-
(1.76 Vp-p ±3 dB).
make sure that the modes change in order of
TV, AV & TV again and the video & audio out-
put are according to the input terminal for each
mode.If connect input to Front and Rear AV
terminal, input terminal of Front AV will be se-
1. Using the TV/AV key on the remote controller,
AUDIO INPUT
CHECK
2 VIDEO AND
lected.
Page 10
21GT-22
400Hz, 100% MODULATION (±50kHz Dev).
output with 400Hz sound and no sound out
HEADPHONE JA CK CHECKING
1. Receive PAL COLOUR PAR with SOUND
1 HEADPHONE
NO. Adjustment part Adjusting procedure and conditions Waveform and others
from speaker.
2. Maximum volume, and check the headphone
OUTPUT
CHECKING
Adjusting procedure and conditions Waveform and others
will change from sound 1 to sound 2.
1. Receive bilingual channel.
2. Press R/C "BILINGUAL" button and the sound
FUNCTION
CHECKING
Adjustment point
1 BILINGUAL
NO.
(Continued)
the COLOUR SYSTEM key to select modes
except PAL, check the COLOUR is not work-
ing properly. Then, select the "PAL" mode.
Check again its colour so that it is working prop-
erly.
nal thru AV, press COLOUR SYSTEM key to
select modes except N4.43/3.58, check the
COLOUR is not working properly. Then, se-
lect the "NTSC 4.43/3.58" mode. Check again
its colour so that it is working properly.
Receive "PAL-B/G" signal, check the sound output
1. Receive the "P AL COLOUR BAR" signal, press
system
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
9 Colour
NO. Adjustment part Adjusting procedure and conditions Waveform and others
2. Receive "NTSC 4.43/3.58 COLOUR BAR" sig-
to make sure it is working properly.
Sound system
10
sure the sound is heard from the speakers.
Then put the unit in no signal state.
1. Receive "PAL COLOUR BAR" signal.
2. Turn up the volume control to maximum, make
3. Check the sound mute is effective.
4. Finally turn sound level of CTV to minimum.
CHECKING
11 NOISE MUTE
10
Check OSD LANGUAGE quantity and type.
TWO OSD LANGUAGE: ENGLISH THAILAND.
LANGUAGE
QUANTITY
CHECK
12 OSD
10-1 10-2
Page 11
21GT-22
REMARK
LAST INITIAL
SETTING DATA
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
00-FF
04 00-0F
08 00-0F
0C 00-0F
MICON EEPROM EEPROM CHASSIS CTV FINAL
DEFAULT RANGE
1B
00-FF
DE
00-FF
53
00-FF
3E
(1) 20th August 2001:
Added 3 new items.
00-FF
00-F3
00
C4
NDF MSA LED-F
SHARPNESS-OFFSET (N358)
SHARPNESS-OFFSET (N443)
SHARPNESS-OFFSET (SECAM)
BG I DK M
AGC1 AGC0 BIL CPTFOB-AV FOA-AV FOB-FE FOA-FE
DATA
PB-SECAM
01 00-3C
3C 00-3C
VOLUME
CONTRAST
1E 00-3C
1E 00-3C
COLOUR
BRIGHTNESS
1E 00-3C
1E 00-3C
TINT
SHARPNESS
01 00-FF
14 00-FF
28 00-FF
0A 00-FF
1E 00-FF
FAV-POS A
FAV-POS B
FAV-POS C
FAV-POS D
POSITION/AV1/AV2
00 00-01
00 00-02
00 00-01
00 00-07
00 00-01
LANGUAGE
BLUE BACK
WHITE-TEMP
LAST POWER MODE
LAST DIGIT MODE (1 OR 2)
80 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
00 00-FF
POS 0
POS 1
POS 2
POS 3
AFT
001:I
S-SYS
000:BG
010:DK
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (HIGHER PART)
1:ON
011:M
0:OFF
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
ADDRESS
REMARK
LAST INITIAL
SETTING DATA
MICON EEPROM EEPROM CHASSIS CTV FINAL
41
40
PASS WORD 4F 00-FF02PASS WORD 43 00-FF03PASS WORD A1 00-FF
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
SM1 SM0 FMWS AV BTSC HTL VMC VMI
HP2 FSL RUS FRA CHN MLY ARB THA
FCO ACL OSO EHT EVG FFI AVL BKS
SECAM N443 N358
45
46
47
48
42
43
44
49
4A4B4C
50
51
525354
55
57
59
56
4F
4D
4E
58
5A5B5C
5D
SKIP 0 SKIP 1 SKIP 2 SKIP 3 SKIP 4 SKIP 5 SKIP 6 SKIP 7
SKIP 8 SKIP 9 SKIP 10 SKIP 11 SKIP 12 SKIP 13 SKIP 14 SKIP 15
SKIP 16 SKIP 17 SKIP 18 SKIP 19 SKIP 20 SKIP 21 SKIP 22 SKIP 23
SKIP 24 SKIP 25 SKIP 26 SKIP 27 SKIP 28 SKIP 29 SKIP 30 SKIP 31
SKIP 32 SKIP 33 SKIP 34 SKIP 35 SKIP 36 SKIP 37 SKIP 38 SKIP 39
SKIP 40 SKIP 41 SKIP 42 SKIP 43 SKIP 44 SKIP 45 SKIP 46 SKIP 47
SKIP 48 SKIP 49 SKIP 50 SKIP 51 SKIP 52 SKIP 53 SKIP 54 SKIP 55
SKIP 56 SKIP 57 SKIP 58 SKIP 59 SKIP 60 SKIP 61 SKIP 62 SKIP 63
SKIP 64 SKIP 65 SKIP 66 SKIP 67 SKIP 68 SKIP 69 SKIP 70 SKIP 71
SKIP 72 SKIP 73 SKIP 74 SKIP 75 SKIP 76 SKIP 77 SKIP 78 SKIP 79
SKIP 80 SKIP 81 SKIP 82 SKIP 83 SKIP 84 SKIP 85 SKIP 86 SKIP 87
SKIP 88 SKIP 89 SKIP 90 SKIP 91 SKIP 92 SKIP 93 SKIP 94 SKIP 95
SKIP 96 SKIP 97 SKIP 98 SKIP 99
60
61
62
63
64
65
66
67
68
5F
5E
69
6A
(1) 20th August
2001:Change of
range & default.
6B
7071727374
6F
6C
6D
6E
MODEL MODEL
76
77
79
75
78
7A
7F
7C
7D
7B
7E
LETTER NO. LETTER NO.
11-1 11-2
AGC TAKE-OVER 0E 00-3F
V-SLOPE 20 00-3F
V-AMPLITUDE 20 00-3F
V-CENTER 20 00-3F
H-CENTER 20 00-3F
H-SIZE 20 00-3F
EW-PARALLELOGRAM 20 00-3F
EW-PARABOLA/WIDTH 20 00-3F
EW-UPPER CORNER 20 00-3F
EW-LOWER CORNER 20 00-3F
EW-TRAPEZIUM 20 00-3F
HORIZONTAL-BOW 20 00-3F
S-CORRECTION 00 00-3F
DRIVE-R (STANDARD) 20 00-3F
DRIVE-G (STANDARD) 20 00-3F
DRIVE-R (WARM) 20 00-3F1ADRIVE-G (WARM) 20 00-3F1BDRIVE-B (WARM) 20 00-3F
DRIVE-B (STANDARD) 20 00-3F
DRIVE-R (COOL) 19 00-3F
DRIVE-G (COOL) 20 00-3F
DRIVE-B (COOL) 20 00-3F
SUB-VOLUME 3F 00-3F
SUB-CONTRAST 3F 00-3F
SUB-COLOUR 20 00-3F
SUB-BRIGHTNESS 20 00-3F
SUB-TINT 20 00-3F
SUB-SHARPNESS 20 00-3F
HTL-VOLUME 20 00-3F
HTL-POSITION FF 00-FF
OSD-REFERENCE 0F 00-0F
CUTOFF LEVEL -OFFSET R 20 00-3F
CUTOFF LEVEL -OFFSET G 20 00-3F
CATHODE DRIVE LEVEL 00 00-0F
Y-DELAY (TV PAL) 0C 00-0F
Y-DELAY (TV SECAM) 0F 00-0F
Y-DELAY (TV N358) 0C 00-0F34Y-DELAY (TV N443) 0C 00-0F
Y-DELAY (TV BW) 0C 00-0F
Y-DELAY (AV PAL) 0C 00-0F
Y-DELAY (AV SECAM) 0F 00-0F
Y-DELAY (AV N358) 0C 00-0F39Y-DELAY (AV N443) 0C 00-0F
Y-DELAY (AV BW) 0C 00-0F
COLOUR-OFFSET (PAL) 08 00-0F
COLOUR-OFFSET (SECAM) 08 00-0F
COLOUR-OFFSET (N358) 04 00-0F3ECOLOUR-OFFSET (N443) 04 00-0F
SHARPNESS-OFFSET (PAL) 08 00-0F
0E
01
040506
00 PASS WORD 55 00-FF
(HEX) D7 D6 D5 D4 D3 D2 D1 D0 DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
ADDRESS DATA
MEMORY MAP
08
09
07
0A
0F
0B
0C
10
11
0D
12
131415
MODEL MODEL
1E
16
17
18
19
1F
1C
202122
1D
25
26
27
28
23
24
2E
29
2A
2F
30
31
32
35
36
2B
2C
2D
37
33
38
3F
3B
3C
3A
3D
LETTER NO. LETTER NO.
11
Page 12
21GT-22
REMARK
LAST INITIAL
SETTING DATA
MICON EEPROM EEPROM CHASSIS CTV FINAL
POS 25
POS 26
POS 27
POS 28
POS 29
DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
POS 30
POS 31
POS 32
POS 33
POS 34
POS 35
POS 36
POS 37
POS 38
POS 39
POS 40
POS 41
POS 42
POS 43
POS 44
POS 45
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CB
POS 6
CA
POS 7
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
ADDRESS DATA
REMARK
POS 4
LAST INITIAL
SETTING DATA
MICON EEPROM EEPROM CHASSIS CTV FINAL
DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
CE
CF
CC
POS 8
CD
D0
D1
D2
D3
D4
D5
D6
POS 9
POS 10
POS 11
DB
D7
D8
D9
DA
POS 12
POS 13
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EB
DE
DC
DD
POS 14
POS 15
POS 16
POS 17
EA
POS 18
EC
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
EE
ED
POS 19
EF
F0
F1
F2
F3
F4
F5
POS 20
POS 21
F6
POS 22
FB
F7
F8
F9
FC
FA
POS 23
POS 24
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
MODEL MODEL
FF
FE POS 46
FD
POS 25
LETTER NO. LETTER NO.
12-1 12-2
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
80
81
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
ADDRESS DATA
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
8E
82
83 TUNING FREQUANCY (HIGHER PART) POS 5
84 TUNING FREQUANCY (LOWER PART)
85
86
87
88
89
8F
8B
8C
90
91
8A
8D
92
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
93
94
95
96
97
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
9E
98
99
9A
9F
9B
9C
9D
A0
A1
A2
A3
A4
A5
A6
12
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
AE
AF
B0
B1
B2
B3
B4
A7
A8
A9
AB
AC
AA
AD
B5
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
MODEL MODEL
BF
B6
B7
B8
B9
BE
BB
BC
BD
BA
LETTER NO. LETTER NO.
Page 13
REMARK
POS 68
POS 69
POS 70
POS 71
LAST INITIAL
SETTING DATA
MICON EEPROM EEPROM CHASSIS CTV FINAL
DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
POS 72
POS 73
POS 74
POS 75
POS 76
POS 77
POS 78
POS 79
POS 80
POS 81
POS 82
POS 83
POS 84
POS 85
POS 86
POS 87
21GT-22
POS 88
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
140
141
142
143
144
145
146
147
148
149
14B
POS 49
14A
POS 50
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
ADDRESS DATA
REMARK
POS 47
POS 48
LAST INITIAL
SETTING DATA
MICON EEPROM EEPROM CHASSIS CTV FINAL
DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
14E
14F
14C
14D
150
151
152
153
154
155
156
157
158
159
15A
POS 51
POS 52
POS 53
POS 54
POS 55
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
15E
15F
15B
15C
15D
160
161
162
163
164
165
166
167
168
169
POS 56
POS 57
POS 58
POS 59
POS 60
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
16E
16F
16B
16C
16D
170
171
172
173
174
175
176
177
POS 64
178
POS 65
16A
POS 61
POS 62
POS 63
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
MODEL MODEL
17E
179
17A
POS 66
17F POS 89
17B
17C
17D
POS 67
LETTER NO. LETTER NO.
13-1 13-2
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
100 POS 46
101
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
ADDRESS DATA
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
102
103
104
105
106
107
108
109
10E
10B
10C
10D
10A
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
10F
110
111
112
113
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
11E
114
115
116
117
118
119
11F
11B
11C
11D
120
121
122
11A
123
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
12E
124
125
126
127
128
129
12F
12B
12C
12D
130
131
132
133
12A
134
13
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
MODEL MODEL
13E
135
136
137
138
139
13A
13F
13B
13C
13D
LETTER NO. LETTER NO.
Page 14
21GT-22
REMARK
LAST INITIAL
SETTING DATA
1C0
1C1
1C2
1C3
1C4
1C5
POS 90
1C6
POS 91
(HEX) D7 D6 D5 D4 D3 D2 D1 D0 DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
ADDRESS DATA MICON EEPROM EEPROM CHASSIS CTV FINAL
REMARK
POS 89
LAST INITIAL
SETTING DATA
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
MICON EEPROM EEPROM CHASSIS CTV FINAL
DEFAULT RANGE
1CB
1C7
1C8
1C9
1CA
POS 92
POS 93
DATA
MODEL MODEL
1CF
1CE
1D0
1D1
1D2
1D3
1D4
1D5
1D6
1D7
1D8
POS 96
1D9
POS 97
1CC
1CD
POS 94
POS 95
1DA
POS 98
1DE
1DF
1E0
1E1
1E2
1E3
1E4
1E5
1E6
1E7
1E8
1DB
1DC
1DD
AV1
POS 99
AV2
1E9
1EA
1EF
1EB
1EE
1F0
1F1
1F2
1F3
1F4
1F5
1F6
1F7
1EC
1ED
1F8
1FE
1FF
1FB
1FC
1F9
1FA
1FD
LETTER NO. LETTER NO.
14-1 14-2
(auto) C-SYS
(auto) C-SYS
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
180
181
182
183
ADDRESS
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
184
S-SYS AFT (auto) C-SYS
185
186
187
188
189
18A
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
18E
18F
18B
18C
18D
190
191
192
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
193
194
195
196
197
198
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
19E
199
19A
19F
19B
19C
19D
1A0
1A1
1A2
1A3
1A4
1A5
1A6
1A7
1A8
14
MODEL MODEL
1BE
1AF
1AB
1AE
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1B9
1A9
1AC
1AD
1AA
1BA
1BF
1BB
1BC
1BD
LETTER NO. LETTER NO.
Page 15
Blown out.
Replace the fuse.
Check F701.
NO RASTER
Check IC701, D701 and
The fuse is again blown out.
Check T701 pin (11) voltage
C705.
Check Secondary Main+B
(Approx. 310V at 220V AC)
(Approx. 130V)
D1001 (Power LED Red
brightly) turns on.
D1001 (Power LED Red
dimly) turns on or turns
ON/OFF.
Check
IC801.
Check
Check CRT connector
K1-K5 bias.
C878.
Checking the
protector circuit.
Does horizontal circuit
oscillate ?
21GT-22
Check Q752 and IC801.
TROUBLE SHOOTING TABLE
Check R701, R707
Check D751
Check R619 and R618.
channel for hotel mode.
#1 Ch 1 is your selected
15-1 15-2
Set vol up/down by R/C key.
press the (one/two digit) key and keep pressing it for five second, then you can see
the hotel mode with four digits password.
mode will be enable, you can switch on/off the hotel mode by using R/C (volume up/
down) key.
HOTEL ON
b) Key in the four digits password starting with number "1", "3", "7", "9", then the hotel
GA1 HOTEL MODE APPLICATION
How to enable/disable the "Hotel Mode" ?
Ans: a) Press the R/C (FUNCTION) key until language selection appear, within five second
Input 1, 3, 7 and 9 by R/C key.
PASSWORD ****
Before set the hotel mode, it is better to choose ch 1 & set s-vol level Up to 75% full scale.
After set hotel mode, starting channel will be always ch 1 & maximum sound level out will
be set the half of full scale.
* We recommend
Preset mode
Fine tuning
Skip mode
System selection
When using hotel mode, user can control "contrast", "brightness", "sharpness" and "tint"
function.
But after power off, it will return to the initial setting.
You can't use:--
The others function is allowed to be used.
power off (same as normal operation)
* If you set hotel mode in AV, starting channel will be the last ch which you received before
CONDITION:
15
Page 16
21GT-22
(Continued)
Check pins(16), (17) and
(34) of IC801.
NEITHER VERTICAL NOR
DEFECTIVE VERTICAL AMP.
HORIZONTAL SYNCHRONIZATION
TROUBLE SHOOTING TABLE
CIRCUIT TO BE CHECKED:
» Sync. Separator Circuit.
Readjust vertical size.
(Bus Data)
Vertical linearity and size
abnormal.
Check R501, R521, R503,
R512, R533 and C533.
AND VERTICAL LINEARITY
Check IC501.Check C505 and C509.
Check IC501 bias.
NO VERTICAL SCAN
Check IC801 and
its related circuit.
No snow noise.
(Continued)
Does the noise level increase at max.
Contrast, Brightness and Sound controls ?
Does noise or signal appear at pin (40)
of IC801 ?
Does noise or
signal appear at
pin (38) of IC801 ?
NO PICTURE, NO SOUND
TROUBLE SHOOTING TABLE
Noise increases but no signal is
received.
Check the tuner supply voltage LB must
be approx. 5V, BT must be approx. 32V.
and CH preset data check.
CIRCUITS TO BE CHECKED:
» Tuner.
» PIF.
» Automatic Gain Control.
» (5V), (32V) Power Source.
Check Q253, Q254
and related circuit.
Check pin (1) of
SF201, Tuner and
related circuit.
Check pin (37) of
IC801 and related
circuit.
Check pin (27) of
IC801, Tuner and
related circuit.
Check the tuner AGC at
TP201.
Check pin(38) of
IC801.
Does signal appear at pins(28)
of IC801?
Check C356 and
NO SOUND
Does noise signal appear at
pin (44) of IC801 ?
CIRCUITS TO BE CHECKED:
» Sound system pins (28)
and (44) of IC801.
» Sound Detector Circuit.
» Sound Switch and Att.
Control.
» Audio Output Circuit.
Does signal appear at pins
Check IC801.
peripheral circuit.
(2) and (4) of IC301 ?
Check Q321, pins(4) and (6)
of IC801 and peripheral
circuit.
16-1 16-2
Check P302, IC301 and
peripheral circuit.
16
Page 17
21GT-22
Is the white balance properly
adjusted ?
Is some colour produced in
B/W broadcast reception ?
NO SPECIFIC COLOUR
TROUBLE SHOOTING TABLE (Continued)
Check IC801, R801, R802,
R803, D804, D805, D806
and Q801.
Readjust the white balance.
The picture colour is yellow.The picture colour is magenta.The picture colour is cyan.
Check Q872, Q887 and its
adjacent circuits.
Check Q871, Q883 and
its adjacent circuits.
Check Q870, Q885 and
its adjacent circuits.
17
“PAL”
Check IC801 and bias
control circuit.
Check X1001(12MHz).
NO SPECIFIC COLOUR
(NO COLOUR SYNCHRONIZATION)
17-1 17-2
Page 18
21GT-22
AT24W04
D601A
B709A
85
1
64 33
4
TX0110BM TX0124BM
2SC3207 2PC1815
DX0111CE
BASE COLLECTOR EMITTER
BASE COLLECTOR EMITTER
16 9
18
28 15
114
BCE
KA7808A
123
CATHODE ANODE (RED)
STRG5653
STV9302A
AN7523
PX0013PE
2SD2586
19
+ ~ ~ -
ZR
:BR:
COLLECTOR
COLLECTOR
BASE EMITTER
BASE EMITTER
JC
COLLECTOR
BASE EMITTER
IX3368CE
TDA9821 M52797SP
2SC2735
132
SOLID STATE DEVICE BASE DIAGRAM
TOP VIEW
SIDE VIEW
18-1 18-2
18
Page 19
WAVEFORMS
21GT-22
1) 1.04 Vp-p 3) 3.40 Vp-p 4) 3.12 Vp-p2) 3.32 Vp-p
6) 90.4 Vp-p
5) 84.8 Vp-p
8) 3.16 Vp-p 9) 2.44 Vp-p 10) 122 Vp-p7) 88.6 Vp-p
11) 8.72 Vp-p 13) 140 Vp-p 14) 1200kVp-p 15) 528 Vp-p12) 47.2 Vp-p
16) 27.2 Vp-p (V) 17) 2.00 Vp-p
19
Page 20
21GT-22
CHASSIS LAYOUT
20
Page 21
21GT-22
21
Page 22
21GT22 21GT22
22~23
BLOCK DAIAGRAM
MAIN UNIT
Page 23
21GT-22
HEADPHONE UNIT
MONO BILINGUAL UNIT
24
Page 24
DESCRIPTION OF SCHEMATIC DIAGRAM
21GT-22
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OP­ERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH “å” ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO RE­PLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAIN­ING THE SAFETY AND PERFORMANCE OF THE SET.
SERVICE PRECAUTION:
THE AREA ENCLOSED BY THIS LINE ( CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANS­FORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.
) IS DIRECTLY
NOTES:
1. The unit of resistance “ohm” is omitted. (K = 1000 ohms, M = Meg ohm).
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless therwise noted. (P = µµF).
VOLTAGE MEASUREMENT CONDITIONS:
1. Voltage in parenthesis measured with no Signal.
2. Voltages without parenthesis measured with PAL Colour-Signal.
3. All the voltages in each point are measured with high impedence volt-meter.
WAVEFORM MEASUREMENT CONDITIONS:
1. Colour bar generator signal of 2.0V peak to peak applied at Base of Video Buffer Amp. Q254.
2. Approximately 4.0 V AGC bias.
25
Page 25
21GT2221GT22
26~27
MAIN UNIT
SCHEMA TIC DIAGRAM
1234567891011 12 13 14 15 16 17 18 19 20
A
B
C
D
E
F
G
H
I
J
Page 26
21GT-22
J
I
H
G
F
CRT UNIT
E
D
C
B
A
HEADPHONE UNIT
12345678910
28
Page 27
21GT-22
29
Page 28
21GT22 21GT22
1234567891011 12 13 14 15 16 17 18 19 20
A
B
C
D
E
F
G
H
I
J
30~31
PWB-A: MAIN UNIT (Copper Side)
PRINTED WIRING BOARD ASSEMBLIES
Page 29
21GT2221GT22
1234567891011 12 13 14 15 16 17 18 19 20
A
B
C
D
E
F
G
H
I
J
32~33
PWB-A: MAIN UNIT (Chip Parts Side)
Page 30
21GT-22
J
I
H
G
(Copper Side)
F
E
D
(Chip Parts Side)
C
PWB-B: CRT UNIT
B
A
12345678910
34
Page 31
21GT-22
J
I
(Copper Side) (Chip Side)
H
PWB-C: HEADPHONE UNIT
G
F
E
D
C3323C3323
(Copper Side)
R3310R3310
C3311C3311
C3313C3313
C3312C3312
C3321C3321
C3320C3320
C3328C3328
RJ3304RJ3304
R3301R3301
RJ3312RJ3312
RJ3314RJ3314
RJ3303RJ3303
C3315C3315
R3300R3300
C3307C3307
R3303R3303
R3302R3302
C3305C3305
C
B
A
12345678910
RJ3301RJ3301
R3306R3306
RJ3308RJ3308
RJ3302RJ3302 RJ3313RJ3313
RJ3305RJ3305
RJ3309RJ3309
Q3301Q3301
RJ3310RJ3310
RJ3315RJ3315
R3313R3313
Q3303Q3303
R3314R3314
(Chip Side)
PWB-D: MONO BILINGUAL UNIT
35
R3308R3308
R3304R3304
C3324C3324
R3309R3309
Q3300Q3300
RJ3307RJ3307
R3316R3316
R3315R3315RJ3311RJ3311
RJ3306RJ3306
Page 32
21GT22
Ref. No. Part No. ★ Description Code
REPLACEMENT PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
MARK : SPARE PARTS-DELIVERY SECTION.
Ref. No. Part No. ★ Description Code
PICTURE TUBE
å V801 VB51LMV20X/~S J Picture Tube å L703 RCiLG0003KJZZ J Degaussing Coil å DY601 RCiLHA028WJZZ J Deflection Yoke
PWB-A DUNTKA541WEE3 - Main Unit — PWB-B DUNTKA542WEB4 - CRT Unit — PWB-C DUNTKA543WEA1 - Headphone Unit — PWB-D DUNTKB232WEA0 - Mono-Billingual Unit —
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
å TU201 VTUVTST5HD970 J VHF Tuner AY
IC301 VHiAN7523++-1 J AN7523 AH
å IC501 VHiSTV9302A-1 J STV9302A, Vert Out
IC601 VHiKA7808AP-1 J KA7808AP AE IC701 VHiSTRG5653-1 J STRG5653, Regulator AQ IC801 RH-iX3368CEN6 J IX3368CE BE IC1005 VHiCAT24W04-1 J CAT24W04
Q201 VS2SC2735//1E~ J 2SC2735 AC Q253 VS2PD601AR/-1~ J 2PD601AR AB Q321 VS2PD601AR/-1~ J 2PD601AR AB Q352 VS2PD601AR/-1~ J 2PD601AR AB Q501 VS2PC1815G+-1+ J 2PC1815G+ AC Q601 VS2SC3207//-1+ J 2SC3207 AC Q602 VS2SD2586//1E J 2SD2586 AM
QEARC2115CEZZ J Ground-Part LHLDW0003PEKZ J ADG Coil Holder AB MSPRT0001PEFJ J CRT Spring AC PMAGF3046CEZZ J Magnet AF
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
DUNTKA541WEE3
PWB-A MAIN UNIT
TUNER
ASSEMBLY NOT INDEPENDENTLY.
INTEGRATED CIRCUITS
TRANSISTORS
Ref. No. Part No. ★ Description Code
Q603 VS2PC1815G+-1+ J 2PC1815G+ AC Q751 VS2PC1815G+-1+ J 2PC1815G+, 5V Reg AC Q752 VS2PC1815G+-1+ J 2PC1815G+, 3.3V Reg AC Q801 VS2PB709AR/-1~ J 2PB709AR AB Q802 VS2PB709AR/-1~ J 2PB709AR AB Q804 VS2PD601AR/-1~ J 2PD601AR AB Q1010 VS2PD601AR/-1~ J 2PD601AR AB
DIODES AND LED
D201 RH-EX0676GEZZ~ J Zener, EX0676GE AA D203 RH-DX0045GEZZ~ J DX0045GE D301 VHD1SS119//-1~ J 1SS119 AA D302 VHD1SS119//-1~ J 1SS119 AA D332 RH-DX0445CEZZ J DX0445CE AL D503 RH-DX0045GEZZ~ J DX0045GE D505 RH-DX0441CEZZ~ J DX0441CE AC D506 RH-EX0630GEZZ~ J Zener, EX0630GE AA D507 RH-DX0045GEZZ~ J DX0045GE D508 RH-DX0131CEZZ~ J DX0131CE AC D509 RH-EX0660GEZZ~ J Zener, EX0660GE D531 RH-EX0627GEZZ~ J Zener, EX0627GE AA D532 RH-EX0627GEZZ~ J Zener, EX0627GE AA D601 RH-DX0048GEZZ~ J DX0048GE D602 VHD1SS244//-1~ J 1SS244 AB D603 RH-EX0667GEZZ~ J Zener, EX0667GE AA D604 VHD1SS119//-1~ J 1SS119 AA D606 RH-DX0131CEZZ~ J DX0131CE AC D607 RH-DX0045GEZZ~ J DX0045GE D608 RH-DX0468CEZZ J DX0468CE AE D651 RH-EX0627GEZZ~ J Zener, EX0627GE AA D652 RH-EX0253TAZZ~ J Zener, EX0253TA D653 RH-DX0045GEZZ~ J DX0045GE D701 RH-DX0111PEZZ J DX0111PE AG D705 VHD1SS82///1A~ J 1SS82 AC D706 VHD1SS82///1A~ J 1SS82 AC D707 VHD1SS82///1A~ J 1SS82 AC D751 RH-DX0229CEZZ J DX0229CE AF D752 RH-DX0131CEZZ~ J DX0131CE AC D755 RH-EX0603GEZZ~ J Zener, EX0603GE AA D760 RH-EX0616GEZZ~ J Zener, EX0616GE AA D801 VHD1SS119//-1~ J 1SS119 AA D802 RH-DX0045GEZZ~ J DX0045GE D803 RH-DX0045GEZZ~ J DX0045GE D804 RH-DX0045GEZZ~ J DX0045GE D805 RH-DX0045GEZZ~ J DX0045GE D806 RH-DX0045GEZZ~ J DX0045GE D808 RH-EX0610GEZZ~ J Zener, EX0610GE AA D1001 RH-PX0013PEZZ J PhotoDiode AC D1003 VHD1SS119//-1~ J 1SS119 AA D1004 VHD1SS119//-1~ J 1SS119 AA D1007 RH-EX0263TAZZ~ J Zener, EX0263TA D1012 RH-EX0611GEZZ~ J Zener, EX0611GE AA D1018 RH-EX0263TAZZ~ J Zener, EX0263TA D1019 RH-EX0263TAZZ~ J Zener, EX0263TA D1024 VHD1SS119//-1~ J 1SS119 AA VA701 RH-VX0073CEZZ J Varistor AD
PACKAGED CIRCUITS
PR701 RMPTP0001PEZZ J Packaged Circuit AN X1001 RCRSB0300CEZZ J Crystal, CRSB0300CE AF
FILTERS
CF253 RFiLC0335CEZZ J Filter, FiLC0335CE SF201 RFiLC0442CEZZ J Filter, FiLC0442CE AL
COILS
L202 VP-DF270K0000~ J Peaking, 27µH 0.1 AB L203 VP-DF270K0000~ J Peaking, 27µH 0.1 AB L204 VP-XF1R2K0000~ J Peaking, 1.2µH 0.1 AB L253 VP-XF100K0000~ J Peaking, 10µH 0.1 AB
å L701 RCiLF0096PEZZ J Coil, AF
L751 RCiLP0225CEZZ J Coil, AF L802 VP-DF100K0000~ J Peaking, 10µH 0.1 AB L803 VP-DF100K0000~ J Peaking, 10µH 0.1 AB L1030 VP-DF100K0000~ J Peaking, 10µH 0.1 AB
36
Page 33
21GT22
Ref. No. Part No. ★ Description Code
L1050 VP-DF100K0000~ J Peaking, 10µH 0.1 AB L1051 VP-DF100K0000~ J Peaking, 10µH 0.1 AB L1030 VP-DF100K0000 R Peaking, 10µHAB L1050 VP-DF100K0000 R Peaking, 10µHAB L1051 VP-DF100K0000 R Peaking, 10µHAB
TRANSFORMERS
å T601 RTRNZ0144PEZZ J Transformer AE å T602 RTRNF0229PEZZ J H-Volt Transformer AY å T701 RTRNW0015PEZZ J Transformer AL
CAPACITORS
C201 VCEA0A1CW476M+ J 47 16V Electrolytic AB C202 VCEA0A1AW337M+ J 330 10V Electrolytic AC C203 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C204 VCEA0A0JW477M+ J 470 6.3V Electrolytic AC C205 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C206 VCEA0A1HW106M+ J 10 50V Electrolytic AB C207 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C208 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C209 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C210 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C231 VCKYCY1HF223Z~ J 0.022 50V Ceramic C232 VCKYCY1HB821K~ J 820p 50V Ceramic C233 VCKYCY1HB472K~ J 4700p 50V Ceramic AA C234 VCKYCY1EF104Z~ J 0.1 25V Ceramic AA C251 VCKYCY1HF223Z~ J 0.022 50V Ceramic C252 VCEA0A1CW107M+ J 100 16V Electrolytic AC C301 VCEA0A1CW477M+ J 470 16V Electrolytic AC C304 VCEA0A1CW106M+ J 10 16V Electrolytic AB C306 VCEA0A1CW106M+ J 10 16V Electrolytic AB C310 VCEA0A1HW105M+ J 1 50V Electrolytic AB C311 VCEA0A1HW105M+ J 1 50V Electrolytic AB C312 VCEA0A1HW224M+ J 0.22 50V Electrolytic AB C316 VCEA0A1CW107M+ J 100 16V Electrolytic AC C331 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C332 VCQYTA1HM103J+ J 0.01 50V Mylar AB C333 VCEA0A1CW108M J 1000 16V Electrolytic AD C352 VCEA0A1HW105M+ J 1 50V Electrolytic AB C354 VCEA0A1HW105M+ J 1 50V Electrolytic AB C356 VCKYCY1HB472K~ J 4700p 50V Ceramic AA C359 VCEA0A1CW106M+ J 10 16V Electrolytic AB C360 VCE9GA1HW225M+ J 2.2 50V Electrolytic AB C409 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C410 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C411 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C412 VCEA0A1CW477M+ J 470 16V Electrolytic AC C501 VCKYPA1HB102K+ J 1000p 50V Ceramic AA C504 VCKYCY1HB103K~ J 0.01 50V Ceramic AA C505 VCEA0A1HW107M+ J 100 50V Electrolytic AB C507 VCKYCY1HB103K~ J 0.01 50V Ceramic AA C508 VCFYSA1JB224J+ J 0.22 63V AD C509 VCEA0A1CW477M+ J 470 16V Electrolytic AC C510 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C514 VCFYSA1JB473J+ J 0.047 63V AC C529 VCKYCY1CB823K~ J 0.082 16V Ceramic AH C531 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C532 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C533 VCQYTA1HM104J+ J 0.1 50V Mylar AB C601 VCQYTA1HM563J+ J 0.056 50V Mylar AB C602 VCEA0A1HW475M+ J 4.7 50V Electrolytic AB C603 VCEA0A1HW105M+ J 1 50V Electrolytic AB C604 VCEA0A2EW106M J 10 250V Electrolytic AD C605 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C606 VCFPVC2DB474J J 0.47 200V AE
MetalIized Polypro Film
C607 VCFPVC3CA802H J 8000p 1600V
MetalIized Polypro Film C608 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C610 VCEA0A1CW108M J 1000 16V Electrolytic AD C611 VCEA0A1EW476M+ J 47 25V Electrolytic AB C612 VCEA0A1CW477M+ J 470 16V Electrolytic AC C620 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C640 VCFYSB2EB823J J 0.082 250V M.Polyester AD C651 VCQYTA1HM222J+ J 2200p 50V Mylar AA C652 VCQYTA1HM472J+ J 4700p 50V Mylar AB
Ref. No. Part No. ★ Description Code
C653 VCEA0A1HW105M+ J 1 50V Electrolytic AB C654 VCKYCY1HF223Z~ J 0.022 50V Ceramic C655 VCEA0A1HW106M+ J 10 50V Electrolytic AB C656 VCEA0A1HW474M+ J 0.47 50V Electrolytic AB C657 VCKYCY1EF104Z~ J 0.1 25V Ceramic AA C658 VCKYCY1EF104Z~ J 0.1 25V Ceramic AA
å C701 RC-FZ031SCEZZ J 0.1 275V AD
C702 RC-KZ0029CEZZ+ J 0.01 250V Ceramic AC C703 RC-KZ0029CEZZ+ J 0.01 250V Ceramic AC C704 RC-KZ0029CEZZ+ J 0.01 250V Ceramic AC C705 RC-EZA097WJZZ J 220 400V Electrolytic C709 RC-KZ0039CEZZ J 680p 2kV Ceramic AB C710 VCEA0A1HW476M+ J 47 50V Electrolytic AB C711 VCKYPA1HB102K+ J 1000p 50V Ceramic AA C712 VCKYPA1HB471K+ J 470p 50V Ceramic AA
å C751 RC-KZ0102GEZZ J 680p
C752 VCKYPH3DB561K J 560p C753 RC-EZ0776CEZZ J 100 160V Electrolytic AF C754 RC-EZA069WJZZ J 33 160V Electrolytic AE C755 VCEA0A1CW108M J 1000 16V Electrolytic AD C756 VCQYTA1HM103J+ J 0.01 50V Mylar AB C759 VCEA0A0JW477M+ J 470 6.3V Electrolytic AC C760 VCEA0A0JW228M J 2200 6.3V Electrolytic AD C801 VCEA0A1HW105M+ J 1 50V Electrolytic AB C803 VCEA0A1CW107M+ J 100 16V Electrolytic AC C804 VCKYCY1HB222K~ J 2200p 50V Ceramic AA C805 VCKYD41HB102K~ J 1000p 50V Ceramic AA C806 VCKYD41HB102K~ J 1000p 50V Ceramic AA C807 VCKYD41HB102K~ J 1000p 50V Ceramic AA C808 VCEA0A1CW107M+ J 100 16V Electrolytic AC C809 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C810 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C811 VCEA0A1CW107M+ J 100 16V Electrolytic AC C812 VCFYFA1HA224J+ J 0.22 50V Mylar AB C813 VCFYFA1HA224J+ J 0.22 50V Mylar AB C814 VCKYCY1HB471K~ J 470p 50V Ceramic AB C816 VCKYCY1HB471K~ J 470p 50V Ceramic AB C1001 VCEA0A0JW107M+ J 100 6.3V Electrolytic AB C1002 VCEA0A0JW107M+ J 100 6.3V Electrolytic AB C1003 VCEA0A1CW106M+ J 10 16V Electrolytic AB C1004 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C1005 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C1006 VCEA0A1CW106M+ J 10 16V Electrolytic AB C1008 VCCCCY1HH330J~ J 33p 50V Ceramic AA C1009 VCCCCY1HH330J~ J 33p 50V Ceramic AA C1010 VCEA0A0JW107M+ J 100 6.3V Electrolytic AB C1011 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C1012 VCKYCY1CF474Z~ J 0.47 16V Ceramic AB C1013 VCEA0A0JW107M+ J 100 6.3V Electrolytic AB C1014 VCEA0A1CW106M+ J 10 16V Electrolytic AB C1016 VCQYTA1HM104J+ J 0.1 50V Mylar AB C1018 VCKYCY1HB221K~ J 220p 50V Ceramic AA C1019 VCEA0A1HW225M+ J 2.2 50V Electrolytic AB C1024 VCQYTA1HM104J+ J 0.1 50V Mylar AB
MetalIized Polypro Film
AC250V
Ceramic AE
2000V
Ceramic AC
RESISTORS
RJ2 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ4 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ9 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ10 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ13 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ14 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ15 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ16 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ17 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ19 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ21 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ24 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ26 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ28 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ32 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ33 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ35 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ37 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ38 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA
37
Page 34
21GT22
Ref. No. Part No. ★ Description Code
RJ41 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ42 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ43 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ46 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ48 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ49 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ51 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ52 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ53 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ56 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ71 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ73 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ75 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ76 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ77 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ78 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ80 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ81 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ82 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ84 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ85 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ86 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ87 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ89 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R201 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R202 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R205 VRS-CY1JF680J~ J 68 1/16W Metal Oxide AA R206 VRS-CY1JF122J~ J 1.2k 1/16W Metal Oxide AA R207 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R208 VRS-CY1JF122J~ J 1.2k 1/16W Metal Oxide AA R209 VRS-CY1JF392J~ J 3.9k 1/16W Metal Oxide AA R216 VRS-VV3LB223J J 22k 3W Metal Oxide AB R219 VRD-RA2BE392J~ J 3.9k 1/8W Carbon AA R220 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R230 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R231 VRD-RA2BE681J~ J 680 1/8W Carbon AA R232 VRS-CY1JF272J~ J 2.7k 1/16W Metal Oxide AA R233 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R234 VRS-CY1JF391J~ J 390 1/16W Metal Oxide AA R257 VRS-CY1JF181J~ J 180 1/16W Metal Oxide AA R258 VRS-CY1JF151J~ J 150 1/16W Metal Oxide AA R259 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R262 VRS-CY1JF561J~ J 560 1/16W Metal Oxide AA R263 VRS-CY1JF561J~ J 560 1/16W Metal Oxide AA R301 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R304 VRS-CY1JF100J~ J 10 1/16W Metal Oxide AA R305 VRS-CY1JF274J~ J 270k 1/16W Metal Oxide AA R310 VRS-CY1JF473J~ J 47k 1/16W Metal Oxide AA R311 VRS-CY1JF473J~ J 47k 1/16W Metal Oxide AA R313 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R314 VRS-CY1JF472J~ J 4.7k 1/16W Metal Oxide AA R315 VRS-CY1JF272J~ J 2.7k 1/16W Metal Oxide AA R316 VRS-CY1JF272J~ J 2.7k 1/16W Metal Oxide AA R318 VRD-RA2BE680J~ J 68 1/8W Carbon AA R334 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R335 VRS-CY1JF564J~ J 560k 1/16W Metal Oxide AA R353 VRS-CY1JF681J~ J 680 1/16W Metal Oxide AA R359 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R360 VRS-CY1JF103J~ J 10k 1/16W Metal Oxide AA R361 VRS-CY1JF104J~ J 100k 1/16W Metal Oxide AA R364 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R366 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R430 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R432 VRS-CY1JF820J~ J 82 1/16W Metal Oxide AA R458 VRS-CY1JF103J~ J 10k 1/16W Metal Oxide AA R459 VRD-RA2BE680J~ J 68 1/8W Carbon AA R501 VRD-RA2BE562J~ J 5.6k 1/8W Carbon AA R502 VRD-RM2HD102J~ J 1k 1/2W Carbon AA R503 VRN-VV3AB2R2J J 2.2 1W Metal Film AA R504 VRS-CY1JF181J~ J 180 1/16W Metal Oxide AA R505 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R506 VRS-VV3AB391J J 390 1W Metal Oxide AA R507 VRN-VV3AB1R0J J 1 1W Metal Film AA R508 VRD-RA2BE153J~ J 15k 1/8W Carbon AA R509 VRD-RA2BE153J~ J 15k 1/8W Carbon AA R511 VRS-CY1JF181J~ J 180 1/16W Metal Oxide AA R512 VRD-RM2HD5R6J~ J 5.6 1/2W Carbon
Ref. No. Part No. ★ Description Code
R521 VRD-RA2BE562J~ J 5.6k 1/8W Carbon AA R529 VRD-RA2BE223J~ J 22k 1/8W Carbon AA R530 VRS-CY1JF334J~ J 330k 1/16W Metal Oxide AA R531 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R532 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R533 VRD-RA2BE393J~ J 39k 1/8W Carbon AA R601 VRS-SV2HC102J J 1k 1/2W Metal Oxide AA R602 VRD-RA2BE393J~ J 39k 1/8W Carbon AA R603 VRD-RA2BE223J~ J 22k 1/8W Carbon AA R604 VRD-RA2BE393J~ J 39k 1/8W Carbon AA R605 VRD-RM2HD823J~ J 82k 1/2W Carbon R606 VRN-VV3DB1R2J J 1.2 2W Metal Film AA R607 VRD-RM2HD270J~ J 27 1/2W Carbon AA R609 VRD-RA2BE154J~ J 150k 1/8W Carbon AA R610 VRD-RA2BE102G~ J 1k 1/8W Carbon R611 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R612 VRS-CY1JF123J~ J 12k 1/16W Metal Oxide AA R613 VRS-CY1JF103J~ J 10k 1/16W Metal Oxide AA R614 VRS-SV2HC100J J 10 1/2W Metal Oxide AA R615 VRS-VV3DB682J J 6.8k 2W Metal Oxide AA R616 VRN-VV3ABR47J J 0.47 1W Metal Film AA R618 VRS-VV3DB391J J 390 2W Metal Oxide AA R619 VRS-VV3LB562J J 5.6k 3W Metal Oxide AB R620 VRS-VV3AB472J J 4.7k 1W Metal Oxide AA R622 VRD-RA2BE102J~ J 1k 1/8W Carbon AA R623 VRD-RM2HD184J~ J 180k 1/2W Carbon AA R624 VRS-CY1JF472J~ J 4.7k 1/16W Metal Oxide AA R625 VRN-VV3DB4R7J J 4.7 2W Metal Film AB R626 VRD-RM2HD470J~ J 47 1/2W Carbon AA R633 VRD-RA2BE333J~ J 33k 1/8W Carbon AA R634 VRD-RA2BE103J~ J 10k 1/8W Carbon AA R641 VRN-SV2HCR47J J 0.47 1/2W Metal Film AA R651 VRS-CY1JF223J~ J 22k 1/16W Metal Oxide AA R652 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R653 VRS-CY1JF822J~ J 8.2k 1/16W Metal Oxide AA R654 VRS-CY1JF273J~ J 27k 1/16W Metal Oxide AA R655 VRS-CY1JF391J~ J 390 1/16W Metal Oxide AA R656 VRS-CY1JF100J~ J 10 1/16W Metal Oxide AA R658 VRD-RA2BE101J~ J 100 1/8W Carbon AA R663 VRD-RA2BE101J~ J 100 1/8W Carbon AA R701 VRW-KQ3NC3R9K J 3.9 7W Cement AE R704 VRN-SV2HC1R0J J 1 1/2W Metal Film AA R707 VRS-VV3DB104J J 100k 2W Metal Oxide AB R708 VRD-RA2BE681J~ J 680 1/8W Carbon AA R709 VRN-VV3DBR47J J 0.47 2W Metal Film AB R710 VRN-VV3DBR39J J 0.39 2W Metal Film AA R711 VRD-RA2BE682J~ J 6.8k 1/8W Carbon AA R712 VRD-RA2BE152J~ J 1.5k 1/8W Carbon AA R716 VRD-RA2BE562J~ J 5.6k 1/8W Carbon AA
å R751 VRC-UA2HG825K~ J 8.2M 1/2W Solid AA å R752 VRC-UA2HG825K~ J 8.2M 1/2W Solid AA
R753 VRD-RM2HD124J~ J 120k 1/2W Carbon AA R754 VRD-RM2HD150J~ J 15 1/2W Carbon AA R755 VRD-RA2BE221J~ J 220 1/8W Carbon AA R756 VRD-RM2HD220J~ J 22 1/2W Carbon AA R757 VRS-CY1JF331J~ J 330 1/16W Metal Oxide AA R765 VRS-CY1JF331J~ J 330 1/16W Metal Oxide AA R801 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R802 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R803 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R804 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R805 VRS-CY1JF822J~ J 8.2k 1/16W Metal Oxide AA R806 VRS-CY1JF123J~ J 12k 1/16W Metal Oxide AA R807 VRS-CY1JF103J~ J 10k 1/16W Metal Oxide AA R808 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R809 VRD-RA2BE224J~ J 220k 1/8W Carbon AA R812 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R813 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R1001 VRS-CY1JF221J~ J 220 1/16W Metal Oxide AA R1002 VRS-CY1JF331J~ J 330 1/16W Metal Oxide AA R1003 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R1004 VRS-CY1JF821J~ J 820 1/16W Metal Oxide AA R1005 VRS-CY1JF181J~ J 180 1/16W Metal Oxide AA R1011 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1012 VRD-RA2BE271J~ J 270 1/8W Carbon R1013 VRD-RA2BE101J~ J 100 1/8W Carbon AA R1014 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA
38
Page 35
21GT22
Ref. No. Part No. ★ Description Code
R1015 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R1016 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1017 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R1019 VRS-CY1JF392J~ J 3.9k 1/16W Metal Oxide AA R1020 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1021 VRS-CY1JF153J~ J 15k 1/16W Metal Oxide AA R1022 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1023 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1024 VRS-CY1JF122J~ J 1.2k 1/16W Metal Oxide AA R1025 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1026 VRS-CY1JF224J~ J 220k 1/16W Metal Oxide AD R1028 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1030 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R1031 VRD-RA2BE562J~ J 5.6k 1/8W Carbon AA R1032 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R1034 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1035 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R1036 VRS-CY1JF332J~ J 3.3k 1/16W Metal Oxide AA R1037 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1038 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1039 VRS-CY1JF223J~ J 22k 1/16W Metal Oxide AA R1040 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1041 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1042 VRD-RA2BE101J~ J 100 1/8W Carbon AA R1046 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1048 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R1050 VRS-CY1JF392J~ J 3.9k 1/16W Metal Oxide AA R1051 VRS-CY1JF683J~ J 68k 1/16W Metal Oxide AA R1072 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R1073 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA
BALUN
FB601 RBLN-0091GEZZ~ J Balun, BLN-0091GE AB
SWITCHES
å S702 QSW-PA006WJZZ J Switch
S1001 QSW-K0003AJZZ+ J Switch, CH Up AB S1002 QSW-K0003AJZZ+ J Switch, CH Down AB S1003 QSW-K0003AJZZ+ J Switch, VOL Up AB S1004 QSW-K0003AJZZ+ J Switch, VOL Down AB S1005 QSW-K0003AJZZ+ J Switch, Picture/Preset AB
MISCELLANEOUS PARTS
å ACC701 QACCZ3008KJSA J AC Cord å F701 QFS-C3229CEZZ J Fuse, T3. 15A 250V AD å FH701 QFSHD1013CEZZ+ J Fuse Holder AC å FH702 QFSHD1014CEZZ+ J Fuse Holder AC
J402 QJAKE0210CE04 J Jack, 3Pin AC J403 QJAKE0210CE09 J Jack, 3Pin AC J409 QJAKH0044AJZZ J Jack, 12Pin AE P302 QPLGN0461CEZZ J Plug, 4Pin AB P303 QPLGN0561CEZZ J Plug, 4Pin AB P601 QPLGN0660CEZZ J Plug, 6Pin AC P602 LHLDW1104PEZZ J Holder AB P603 QPLGN0341CEZZ J Plug, 3Pin AA P701 QPLGN0260CEZZ J Plug, 2Pin AC P702 QPLGA0201PEZZ J Plug, 2Pin P1001 LHLDW1105PEZZ J Holder AB P1002 QPLGN0561CEZZ J Plug, 5Pin AB RDA302 PRDAR0340PEFW J Heat Sink, IC301 AE RDA501 PRDAR0118GJFW J Heat Sink, IC501 AD RDA602 PRDAR0224PEFW J Heat Sink, Q602 AF RDA701 PRDAR0298PEFW J Heat Sink, IC701 AF RMC1001 TP201 QLUGP0102PEZZ J Lug AA
LHLDP1066PE00 J Holder AC
RRMCU0222CEZZ J Remote Receiver AL
DUNTKA542WEB4
PWB-B CRT UNIT
Q870 RH-TX0110BMZZ+ J TX0110BM AC Q871 RH-TX0110BMZZ+ J TX0110BM AC
TRANSISTORS
Ref. No. Part No. ★ Description Code
Q872 RH-TX0110BMZZ+ J TX0110BM AC Q883 RH-TX0124BMZZ+ J TX0124BM AC Q885 RH-TX0124BMZZ+ J TX0124BM AC Q887 RH-TX0124BMZZ+ J TX0124BM AC
DIODES
D881 VHD1SS244//-1~ J 1SS244 AB D882 VHD1SS244//-1~ J 1SS244 AB D883 VHD1SS244//-1~ J 1SS244 AB D884 VHD1SS119//-1~ J 1SS119 AA D885 VHD1SS119//-1~ J 1SS119 AA D886 VHD1SS82///1A~ J 1SS82 AC D887 VHD1SS82///1A~ J 1SS82 AC D888 VHD1SS82///1A~ J 1SS82 AC
CAPACITORS
C871 VCCCCY1HH471J~ J 470p 50V Ceramic AA C872 VCCCCY1HH471J~ J 470p 50V Ceramic AA C873 VCCCCY1HH471J~ J 470p 50V Ceramic AA C875 VCKYPA2HB102K+ J 1000p 500V Ceramic AA C876 RC-KZ0150CEZZ J 1000p 3kV Ceramic AB C878 VCEA0A2EW106M+ J 10 250V Electrolytic AD C880 VCCCCY1HH471J~ J 470p 50V Ceramic AA C881 VCKYPA1HB471K+ J 470p 50V Ceramic AA C882 VCKYPA1HB471K+ J 470p 50V Ceramic AA C886 VCKYPA2HB102K+ J 1000p 500V Ceramic AA
RESISTORS
R879 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R880 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R881 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R882 VRS-VV3DB153J J 15k 2W Metal Oxide AA R883 VRD-RM2HD272J~ J 2.7k 1/2W Carbon AA R884 VRS-VV3DB153J J 15k 2W Metal Oxide AA R885 VRD-RM2HD272J~ J 2.7k 1/2W Carbon AA R886 VRS-VV3DB153J J 15k 2W Metal Oxide AA R887 VRD-RM2HD272J~ J 2.7k 1/2W Carbon AA R892 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R893 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R894 VRS-CY1JF102J~ J 1k 1/16W Metal Oxide AA R895 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R896 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R899 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA
MISCELLANEOUS PARTS
å SC883 QSOCV0016PEZZ J Socket, 11Pin AF
P882 LHLDW1105PEZZ J Holder, 5Pin AB P884 LHLDW1104PEZZ J Holder, 4Pin AB
DUNTKA543WEA1
PWB-C HEADPNONE UNIT
RESISTORS
RJ60 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ61 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ62 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R370 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA R371 VRS-CY1JF471J~ J 470 1/16W Metal Oxide AA
MISCELLANEOUS PARTS
J351 QJAKJ0101SEZZ J Jack, 7Pin AE P351 QPLGN0461CEZZ J Plug, 4Pin AB
DUNTKB232WEA0
PWB-D MONO-BILLINGUAL UNIT
INTEGRATED CIRCUITS
IC3300 VHiTDA9821/-1 J TDA9821 AR IC3301 VHiM52797SP-1 J M52797SP AP
39
Page 36
21GT22
Ref. No. Part No. ★ Description Code
TRANSISTORS
Q3300 VS2PD601AR/-1~ J 2PD601AR AB Q3301 VS2PD601AR/-1~ J 2PD601AR AB Q3303 VS2PD601AR/-1~ J 2PD601AR AB
FILTER
CF3300 RFiLC0338CEZZ J Filter, FiLC0338CE AG
COILS
L3300 VP-DF1R0K0000~ J Peaking, 1µH 0.1 AB L3301 VP-DF1R0K0000~ J Peaking, 1µH 0.1 AB
CAPACITORS
C3300 VCEA0A1HW225M+ J 2.2 50V Electrolytic AB C3301 VCEA0A1HW225M+ J 2.2 50V Electrolytic AB C3302 VCEA0A1HW225M+ J 2.2 50V Electrolytic AB C3303 VCEA0A1HW225M+ J 2.2 50V Electrolytic AB C3304 VCEA0A1CW107M+ J 100 16V Electrolytic AC C3305 VCKYCY1HF223Z~ J 0.022 50V Ceramic C3306 VCKYPA1HB222K+ J 2200p 50V Ceramic AA C3307 VCKYCY1HB223K~ J 0.022 50V Ceramic C3308 VCKYPA1HF103Z+ J 0.01 50V Ceramic AA C3309 VCQYTA1HM102J+ J 1000p 50V Mylar AB C3310 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3311 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C3312 VCCCCY1HH221J~ J 220p 50V Ceramic AA C3313 VCCCCY1HH221J~ J 220p 50V Ceramic AA C3314 VCEA0A1CW107M+ J 100 16V Electrolytic AC C3315 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C3316 VCEA0A1CW107M+ J 100 16V Electrolytic AC C3317 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3318 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3319 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3320 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C3321 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C3322 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3323 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C3324 VCKYCY1HF103Z~ J 0.01 50V Ceramic AA C3325 VCEA0A1CW226M+ J 22 16V Electrolytic AB C3326 VCEA0A1HW106M+ J 10 50V Electrolytic AB C3327 VCEA0A1CW106M+ J 10 16V Electrolytic AB C3328 VCKYCY1HB102K~ J 1000p 50V Ceramic AA C3330 VCEA0A1CW106M+ J 10 16V Electrolytic AB
Ref. No. Part No. ★ Description Code
MISCELLANEOUS PARTS
SP301 RSP-Z0005KJZZ J Speaker AQ SP302 RSP-Z0005KJZZ J Speaker AQ
QCNW-A230WJZZ J Connecting Cord AD QCNW-A500WJZZ J Connecting Cord AD QCNW-0026KJZZ J Connecting Cord AF QCNW-2452PEZZ J Connecting Cord AE
SUPPLIED ACCESSORIES
ACCESSORIES
RRMCG0018KJSA J Infrared R-C AX TiNS-A458WJZZ J Operation Manual
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKCA245WJZZ - Packing Case — SPAKP0697CEZZ - Wrapping Paper — SPAKXA126WJZZ - Packing Add. — SPAKXA166WJZZ - Packing Add. — SSAKA0230CEZZ - Polyethylene Bag — TLABMA181WJZZ - Model Label — TLABN0148KJZZ - Serial Label — TLABVA093WJZZ - Bar Code Label — TLABZA105WJZZ - Label —
RJ3301 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ3307 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ3309 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ3312 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA RJ3314 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R3300 VRS-CY1JF122J~ J 1.2k 1/16W Metal Oxide AA R3301 VRS-CY1JF122J~ J 1.2k 1/16W Metal Oxide AA R3302 VRS-CY1JF273J~ J 27k 1/16W Metal Oxide AA R3303 VRS-CY1JF153J~ J 15k 1/16W Metal Oxide AA R3304 VRS-CY1JF561J~ J 560 1/16W Metal Oxide AA R3305 VRD-RA2BE101J~ J 100 1/8W Carbon AA R3306 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R3307 VRD-RA2BE561J~ J 560 1/8W Carbon R3308 VRS-CY1JF102J~ J 1 k 1/16W Metal Oxide AA R3309 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R3310 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R3311 VRD-RA2EE680J~ J 68 1/4W Carbon AA R3312 VRD-RA2EE680J~ J 68 1/4W Carbon AA R3313 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA R3314 VRS-CY1JF102J~ J 1 k 1/16W Metal Oxide AA R3315 VRS-CY1JF101J~ J 100 1/16W Metal Oxide AA R3316 VRS-CY1JF000J~ J 0 1/16W Metal Oxide AA
MISCELLANEOUS PARTS
P3300 QPLGZ0810CEZZ J Plug, 8Pin AD P3301 QPLGZ0810CEZZ J Plug, 8Pin AD P3302 QPLGZ0810CEZZ J Plug, 8Pin AD
RESISTORS
40
Page 37
21GT22
Ref. No. Part No. ★ Description Code
CABINET PARTS
1 CCABAA134WEA0 Front Cabinet Ass'y 1-1 Not Avairable - Front Cabinet — 1-2 HBDGB0001KJSC J SHARP Badge AE 1-3 GCOVAA184WJSA J RC/LED Cover 1-4 JBTN-A062WJSA Control Button 1-5 JBTN-A063WJSA J Power Button 1-6 MSPRC0005PEFW J Power Button Spring AB 2 CCABB0064WEA0 J Rear Cabinet Ass’y 2-1 Not Avairable - Rear Cabinet —
CABINET PARTS LOCATION
Ref. No. Part No. ★ Description Code
1-6
1-5
1-3
1-2
1-4
41
Page 38
21GT22
Ref. No. Part No. ★ Description Code
P ACKING OF THE SET
Ref. No. Part No. ★ Description Code
42
Page 39
21GT22
Ref. No. Part No. ★ Description Code
- M E M O -
Ref. No. Part No. ★ Description Code
43
Page 40
21GT22
Ref. No. Part No. ★ Description Code
Ref. No. Part No. ★ Description Code
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
TQ1457-S
Dec. 2002 Printed in Japan
In Japan gedruckt
Design and Production Information Design : SEM Production : STTM
MY. DS
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
44
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use