In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
Specifications are subject to change without
prior notice.
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
Page 2
21FL96
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
2
Page 3
2
2
IMPORTANT SERVICE SAFETY PRECAUTION
1.5k ohm
10W
0.15
µ
F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
(Continued)
21FL96
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Page 4
21FL96
LOCATION OF USER'S CONTROL
Front Panel
POWER
Press → On.
Press again
SENSOR AREA FOR
REMOTE CONTROL
MENU
Press
Press again
→ Off.
→ Accesses MAIN MENU.
→ Exits MAIN MENU.
VOLUME UP/DOWN
(+) Increases sound.
(
) Decreases sound.
Basic Remote Control Functions
POWER
Press " On.
Press again " Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASH BACK
Returns to previous channel.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MUTE
Press Mutes sound.
Press again Restores sound.
• CLOSED CAPTION appears when
sound is muted.
VIDEO IN 2 L-AUDIO-R
(INSIDE DOOR)
CHANNEL UP/DOWN
(') Selects next higher channel.
) Selects next lower channel.
(
"
Infrared Transmitter Window
INPUT
Press " Switch to external video input
mode.
Press again " Switch to TV mode.
CHANNEL UP/DOWN
(p)
Selects next higher channel.
(q
) Selects next lower channel.
• Moves the
screen.
MENU
Press " Accesses MAIN MENU.
Press again " Exits MAIN MENU.
DISPL AY
Press " Displays receiving channel for
4 seconds.
Press again " Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
” mark of the MENU
Note:
The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
The degree of illumination will vary depending on the strength of lighting used.
The degree of illumination will decrease with time and depending on the temperature.
The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
Sunlight and fluorescent lighting are the most effective when charging the display.
4
Page 5
21FL96
INSTALLATION AND SERVICE INSTRUCTIONS
Note:(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to P603 Pin3 and make
sure that the voltmeter reads 18.9 ±1.1V.
5. Apply external 24.5V DC at P603 Pin3 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord at least 4
second before plugging in again. Now make sure that
normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 28.6kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
5
Page 6
21FL96
SERVICE MODE
Service Mode Overview
1. Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
2. Service mode is cleared by entering SERVICE key or CH-UP +VOL-DOWN key command during service mode.
3. If key input port (SERVICE) input is LOW, then it is in service mode.
4. During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE or CH-UP + VOLDOWN is disabled.
5. Service mode can be switched to 4 modes as follows by key input MENU;
Option mode
Adjustment mode
Setting mode
Check mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer and Off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M02, M03, M04, M05, and M06.
First mode of service mode when SERVICE key is
pressed.
First mode of service mode when local key
CH-UP + VOL-DOWN is pressed after MCU reset.
6
Page 7
21FL96
Adjustment Mode Items
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA309 and JA402
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F51
to go into third stage of service mode data, press MENU key
Third stage data from 001 ~ 020
Below is the contents of these data
First Stage
No.Item NameICRegisterRangeDefault
V01SUB-PICTURE1 ChipCONTRAST0~127127
V02SUB-TINT1 ChipTINT0~12764
V03SUB-COLOR1 ChipCOLOR0~12764
V04SUB-BRIGHT1 ChipBRIGHT0~255128
V05 SUB-SHARP 1 Chip VIDEO-TONE 0~63 32
V06 V-SHIFT 1 Chip V-SHIFT 0~7 7
V07H-SHIFT1 ChipH-PHASE0~3116
V08RF-AGC1 ChipRF-Delay0~127127
V09V-SIZE1 ChipV-SIZE0~6332
V10PIF-VCO1 ChipVIF-VCO0~6332
V11 R-CUTOFF 1 Chip R-CUTOFF 0~255 64
V12 G-CUTOFF 1 Chip G-CUTOFF 0~255 64
V13 B-CUTOFF 1 Chip B-CUTOFF 0~255 64
V14R-DRIVE1 ChipR-DRIVE0~12764
V15B-DRIVE1 ChipB-DRIVE0~12764
V16SUB-COLOR(YUV)1 ChipCOLOR0~12764
V17SUB-TINT(YUV)1 ChipBASEBAND-TINT0~12764
V18CC-POSMicron0~25532
V19(Vertical mode)1 ChipV-MUTE,SERVICE0, 1, 20
V20SUB-VOL1 ChipA-ATT0~127127
V21H-VCO1 ChipH-VCO0~74
M01 MTS-ATT MTS ATT 0~15 16
M02 MTS-VCOMTSVCO0~6332
M03 MTS-FILTERMTSFILTER0~6328
M04 MTS-WIDEBANDMTSWIDEBAND0~6327
M05 MTS-SPECTRALMTSSPECTRAL0~6332
M06SUB-VOLMTSVOL0~6363
ADJUSTMENT METHOD
Auto Adjustment Item
1. H-VCO (Currently need manual adj)
2. RF-AGC
3. PIF-VCO
4. MTS-FILTER
7
Page 8
21FL96
Ë
SELF ADJUSTMENT
H-VCO
1. When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
2. H-FREE(1chip) is set to 1.
3. H-OUT is set by intelligent monitor output.
4. IM input is set as TIM input.
5. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
6. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
7. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1. When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
2. AGC-OUT is set by intelligent monitor output.
3. IM input is set as AD input.
4. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1. When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
2. VIF-DEF(1chip) is set to 1.
3. AFC is set by intelligent monitor output.
4. IM input is set as AD input.
5. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
6. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
7. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
MTS-FILTER
Adjustment is performed in the center of the range when FILTER status is OK.
1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B.
2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D.
No ITEM 0 1 DEFAULT
O01 DEM0 Without DEMO With DEMO 1
O02 DOWNLOAD Without V-CHIP OP With V-CHIP OP 1
O03 V-CHIP Without V-CHIP With V-CHIP 1
O04 SPEAKER Without SPEAKER With SPEAKER 1
O05 FAO Without FAO With FAO 1
O06 P.PREF Without P.PREF With P.PREF 1
O07 UNIV+ Without UNIV+ With INIV+ 1
O08 VIEW TIMER Without VIEW TIMER With VIEW TIMER 1
O09 EZ-SETUP EZ-SETUP AUTO PRESET 1
O10 PON-CH Without POWER-ON With POWER-ON 1
O11 FAV-COL FAV-COL COL-TEMP 1
O12 COMPONENT Without COMPONENT With COMPONENT 1
O13 AV Without AV With AV 1
O14 AV2 AV1 system AV2 system 1
O15 MTS Without MTS With MTS 1
O16 TONE-CTRL Without S-ADJ With S-ADJ 1
O17 AUTO-OFF Without AUTO-OFF With AUTO-OFF 1
O18 INIT-LANG ENGLISH SPANISH 1
O19 SETUP-FLAG NO SETUP AUTO SETUP 1
3: Display "FRONT A/V INPUTS" and
"REAR A/V INPUTS" in DEMO mode.
O20 FR.AV (Front, 3
Rear AV)
2: Display "FRONT A/V INPUTS" only in
DEMO mode.
1: Display "REAR A/V INPUTS" only in
DEMO mode.
0: No display of above lines in DEMO mode.
21FL96
Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.
11
Page 12
21FL96
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
654321
12
Page 13
654321
A
B
C
D
E
F
G
H
21FL96
CRT BLOCK DIAGRAM
13
Page 14
21FL96
J
I
H
G
MAIN BLOCK DIAGRAM
F
E
D
C
B
A
12345678910
14
Page 15
21FL96
10111213141516171819
15
Page 16
21FL96
J
I
H
G
MTS BLOCK DIAGRAM
F
E
D
C
B
A
12345678910
16
Page 17
DESCRIPTION OF SCHEMATIC DIAGRAM
21FL96
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
µ
2. All voltages measured with 1000
signal.
V B & W or Color
WAVEFORMS
WAVEFORM MEASUREMENT CONDITIONS:
1.
Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
ç
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES
PIECES RELATIVES A LA SECURITE.
MARQUE
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER2. REF. NO.
3. PART NO.4. DESCRIPTION
« MARK: SPARE PARTS-DELIVERY SECTION
MARK: X-RAY RELATED PARTS
p
Ref. No. Part No. Description Code
PICTURE TUBE
SU V101 VB51QDK690X2E X Picture Tube CB
U L706 RCILG0069PEZZ X Degaussing Coil AP
PRINTED WIRING BOARD ASSEMBLIES
PWB-A DUNTKC522WEB0 X MAIN Unit —
PWB-B DUNTKA599WEG3 X CRT Unit —
PWB-C DUNTKC574WEA0 X MTS Unit —
QEARCA012WJZZ X Grounding Strap AE
(NOT REPLACEMENT ITEM)
PWB-A: DUNTKC522WEB0
MAIN UNIT
TUNER
NOTE:THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDETLY
U TU201 VTUVT1T5UF202 X Tuner AS
INTEGRATED CIRCUITS
IC301VHIAN17820B-1X AN17820BAK
IC401VHIMM1501XN-1Y X MM1501XNAD
IC402VHIMM1501XN-1Y X MM1501XNAD
U IC501VHIAN15525A-1X AN15525AAF
IC601VHIKA78R09AP1X KIA78R09APIAE
U IC701 VHISTRW6753-1 X STR-W6753 AL
U IC702RH-FXA003WJZZX PC123Y82AC
U IC703VHISE125N++-FX SE125NAF
IC801VHIM61251CF1EQ X M61251CPAR
IC1001 RH-IXA983WJZZX RU3AMLF-C4AN
IC1003 VHIBR24L04F-1YX BR24L04F-WE2AD
D201RH-EX0676GEZZY X ZenerDiode 32VAB
D203VHD1SS119//-1YX DiodeAA
D392RH-DX0452CEZZX DiodeAF
D502VRD-RA2BE103JY X 10k1/8W Carbon AA
D503RH-EX0612GEZZY X EX0612GEAB
D505RH-DX0441CEZZY X DiodeAA
D510RH-DX0131CEZZY X DiodeAB
D601VHD1SS119//-1YX DiodeAA
D602VHD1SS244//-1YX DiodeAB
D603RH-EX0665GEZZY X ZenerDiode, 5VAB
D606RH-DX0131CEZZY X DiodeAB
U D701RH-DX0476CEZZX DiodeAE
D702RH-DX0490CEZZY X DiodeAB
D703VHD1SS119//-1YX DiodeAA
D704RH-EX0650GEZZY X Zener Diode 16VAB
D705RH-DX0066GEZZY X DiodeAC
D706RH-DX0066GEZZY X DiodeAC
D707RH-DX0066GEZZY X DiodeAC
D708RH-EX0621GEZZY X ZenerAB
D710VHD1SS119//-1YX DiodeAA
D714VHD1SS119//-1YX DiodeAA
D716RH-EX0601GEZZY X ZenerDiode, 3.7VAB
D751RH-DXA006WJZZX DiodeAD
D752RH-DX0247CEZZX DiodeAD
D801RH-EX1393CEZZY X EX1393CEAB
D802RH-EX0630GEZZY X ZenerDiode 9.1VAB
D803VHD1SS119//-1YX DiodeAA
D806VHD1SS119//-1YX DiodeAA
D1001 RH-PX0013PEZZX LED, ON TIMERAB
D1081 VHD1SS119//-1YX DiodeAA
D1085 RH-EX1393CEZZY X EX1393CEAB
D1086 RH-EX1393CEZZY X EX1393CEAB
C201VCEA0A1CW476M+X 4716VEL.AA
C202VCEA0A0JW108M+X 10006.3VEL.AB
C203VCKYCY1HF103ZYX 0.0150VCeramic AA
C205VCKYCY1HF103ZYX 0.0150VCeramic AA
C206VCEA0A1HW106M+X 1050VEL.AA
C207 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C208VCKYCY1HF103ZYX 0.0150VCeramic AA
C209VCKYCY1HF103ZYX 0.0150VCeramic AA
C210VCKYCY1HF103ZYX 0.0150VCeramic AA
C213VCKYCY1HB102KYX 1000p 50VCeramic AA
C301VCEA0A1CW477M+X 47016VEL.AB
C304VCEA0A1CW106M+X 1016VEL.AA
C308VCKYCY1HB822KYX 8200p 50VCeramic AA
C310VCEA0A1HW105M+X 150VEL.AA
C311VCEA0A1HW105M+X 150VEL.AA
C312VCEA0A1HW224M+X 0.2250VEL.AA
C313VCKYCY1HB822KYX 8200p 50VCeramic AA
C317VCE9GA1CW106M+X 1016VEL.AB
C318VCEA0A1CW107M+X 10016VEL.AA
C321VCEA0A1HW224M+X 0.2250VEL.AA
C322VCEA0A1HW105M+X 150VEL.AA
C391VCKYPA1HB102K+X 1000p 50VCeramic AA
C392VCQYTA1HM103J+X 0.0150VMylarAA
C393VCEA0A1EW108M+X 100025VEL.AC
C434VCE9GA1CW106M+X 1016VEL.AB
C435VCE9GA1CW106M+X 1016VEL.AB
C436VCKYCY1EF104ZYX 0.125VCeramic AA
C437VCE9GA1HW106M+X 1050VEL.AC
Ref. No. Part No. Description Code
C438VCEA0A1CW106M+X 1016VEL.AA
C439VCKYCY1HF103ZYX 0.0150VCeramic AA
C452VCE9GA1CW106M+X 1016VEL.AB
C505VCEA0A1HW107M+X 10050VEL.AB
C508VCFYAA2AA224J+X 0.22100VM-Poly. AC
C511VCEA0A1VW477M+X 47035VEL.AC
C512VCKYPA2HB102K+X 1000p 500VCeramic AA
C513RC-EZA332WJZZ+X 100035VEL.AD
C515VCEACA1HC335J+X 3.350VEL.AC
C601VCQYTA1HM563J+X 0.05650VMylarAA
C602VCEA0A1HW475M+X 4.750VEL.AA
C603VCEA0A1HW105M+X 150VEL.AA
C604VCEA0A2EW336M+X 33250VEL.AD
C606VCKYPA2HB102K+X 1000p 500VCeramic AA
S U C607VCFPVC3ZA912HX 9100p 1800 V M.Poly. AC
C608VCQYTA2AA103K+X 10000p 100VMylarAB
C610VCEA0A1EW227M+X 22025VEL.AB
C611VCFPVC2DB334JX 0.33250VM-Poly. AC
C642VCEA0A1EW476M+X 4725VEL.AA
C643VCEA0A1AW477M+X 47010VEL.AB
C650VCKYPA2HB101K+X 100p500VCeramic AA
U C701RC-FZ029SCEZZX 0.22250VCeramic AC
C702RC-KZ0029CEZZ+X 0.01AC250V Ceramic AB
C703RC-KZ0029CEZZ+X 0.01AC250V Ceramic AB
C704RC-KZ0029CEZZ+X 0.01AC250V Ceramic AB
U C705RC-EZA097WJZZX 220400VEL.AK
C706VCEA0A1VW226M+X 2235VEL.AA
C708VCKYPA1HB471K+X 470p50VCeramic AA
C709VCEA9M1HW105M+X 150VEL.AA
C710VCQYTA1HM104J+X 0.150VMylarAB
C711VCKYPA1HB681K+X 680p50VCeramic AA
C718VCKYPA2HB472K+X 4700p 500VCeramic AB
C743VCKYPH3DB561KX 560p2kVCeramic AB
U C750VCKYPA2HB102K+X 1000p 500VCeramic AA
C751RC-KZ0106GEZZX 3300p AC250V Ceramic AC
C752VCKYPH3DB561KX 560p2kVCeramic AB
C753RC-EZ0724CEZZX 100160VEL.AE
C754RC-EZ0638CEZZX 33160VEL.AD
C755VCQYTA1HM103J+X 0.0150VMylarAA
C756VCEA0A1EW228M+X 220025VEL.AD
C757VCKYCY1HB471KYX 470p50VCeramic AA
C784RC-KZ0341CEZZX 1000p 2kVCeramic AD
C801VCFYFA1HA105J+X 150VM-Poly. AC
C802VCKYCY1HF103ZYX 0.0150VCeramic AA
C803VCEA9M1CW476M+X 4716VEL.AA
C804VCKYCY1HF103ZYX 0.0150VCeramic AA
C805VCEA0A1HW105M+X 150VEL.AA
C806VCKYCY1HF103ZYX 0.0150VCeramic AA
C807VCEA0A1CW337M+X 33016VEL.AB
C808VCKYCY1HF103ZYX 0.0150VCeramic AA
C809VCKYCY1HF103ZYX 0.0150VCeramic AA
C810VCKYCY1HF103ZYX 0.0150VCeramic AA
C811VCEA9M1CW106M+X 1016VEL.AA
C814VCKYCY1HF103ZYX 0.0150VCeramic AA
C815VCKYCY1HF103ZYX 0.0150VCeramic AA
C816VCKYCY1EF104ZYX 0.125VCeramic AA
C817VCEA9M1CW107M+X 10016 VEL.AB
C818VCEA9M1HW475M+X 4.750VEL.AA
C819VCCCCY1HH121JYX 120p50 VCeramic AA
C820VCEA9M1HW474M+X 0.4750VEL.AA
C821VCKYCY1HF153ZYX 0.01550VCeramic AA
C822VCE9GA1HW105M+X 150VEL.AB
C823VCKYCY1EF104ZYX 0.125VCeramic AA
C824VCEA0A1CW337M+X 33016VEL.AB
C825VCE9GA1HW105M+X 150VEL.AB
C826VCKYCY1HF103ZYX 0.0150VCeramic AA
C827VCEA0A1CW476M+X 4716VEL.AA
C828VCKYCY1HF103ZYX 0.0150VCeramic AA
C829VCEA9M1CW476M+X 4716VEL.AA
C831VCKYCY1EF104ZYX 0.125VCeramic AA
R209VRS-CY1JF392JYX 3.9k1/16WM-Ox.AA
R216VRS-RG3LB333J+X 33k3.0WM-Ox.AB
R220VRS-CY1JF221JYX 2201/16WM-Ox.AA
R301VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R302VRN-RL3DBR10J+X 0.102WM-FilmAB
R303VRS-CY1JF473JYX 47k1/16WM-Ox.AA
R304VRD-RA2BE683JYX 68k1/8WCarbon AA
R305VRS-CY1JF274JYX 270k1/16WM-Ox.AA
R307VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R308VRS-CY1JF822JYX 8.2k1/16WM-Ox.AA
R311VRD-RA2BE103JYX 10k1/8WCarbon AA
R314VRS-CY1JF822JYX 8.2k1/16WM-Ox.AA
R315VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R362VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R363VRS-CY1JF564JYX 560k1/16WM-Ox.AA
R365VRS-CY1JF564JYX 560k1/16WM-Ox.AA
R366VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R381VRS-CY1JF564JYX 560k1/16WM-Ox.AA
R382VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R383VRS-CY1JF564JYX 560k1/16WM-Ox.AA
R384VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R431VRS-CY1JF101JYX 1001/16WM-Ox.AA
R432VRS-CY1JF750JYX 751/16WM-Ox.AA
R433VRS-CY1JF750JYX 751/16WM-Ox.AA
R434VRS-CY1JF750JYX 751/16WM-Ox.AA
R435VRS-CY1JF750JYX 751/16WM-Ox.AA
R436VRD-RA2BE101JYX 1001/8WCarbon AA
R437VRS-CY1JF101JYX 1001/16WM-Ox.AA
R438VRS-CY1JF000JYX 001/16WM-Ox.AA
R461VRS-CY1JF750JYX 751/16WM-Ox.AA
R462VRS-CY1JF101JYX 1001/16WM-Ox.AA
R503VRN-RL3DB1R2J+X 1.22WM-FilmAB
R504VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R506VRS-RG3AB331J+X 3301WM-Ox.AB
R507VRD-RM2HD1R0JYX 11/2WCarbon AA
R513VRD-RM2HD333JYX 33k1/2WCarbon AA
R514VRD-RM2HD682JYX 6.8k1/2WCarbon AA
R520VRS-CY1JF153JYX 15k1/16WM-Ox.AA
R524VRD-RA2BE103JYX 10k1/8WCarbon AA
R525VRD-RA2BE102JYX 1k1/8WCarbon AA
R526VRD-RA2BE101JYX 1001/8WCarbon AA
R601VRD-RM2HD220JYX 221/2WCarbon AA
R602VRD-RA2BE393JYX 39k1/8WCarbon AA
R603VRD-RA2BE273JYX 27k1/8WCarbon AA
R604VRD-RA2BE473JYX 47k1/8WCarbon AA
R605VRD-RM2HD104JYX 100k1/2WCarbon AA
U R608VRD-RM2HD102JYX 1.0k1/2WCarbon AA
R609VRD-RM2HD270JYX 271/2WCarbon AA
U R611VRN-RL3AB1R5J+X 1.51WM-FilmAB
U R612VRD-RM2HD270JYX 271/2WCarbon AA
R613VRS-CY1JF000JYX 001/16WM-Ox.AA
R614VRD-RA2BE154JYX 150k1/8WCarbon AA
R615VRD-RA2BE102JYX 1k1/8WCarbon AA
R616VRD-RA2BE102JYX 1k1/8WCarbon AA
R617VRS-CY1JF123JYX 12k1/16WM-Ox.AA
R618VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R621VRN-RL2HC4R7J+X 4.71/2WM-FilmAB
R622VRS-VV3DB682JX 6.8k2WM-Ox.AA
R631VRS-KT3LB391JX 3903WM-Ox.AD
R637VRD-RA2BE331JYX 3301/8WCarbon AA
R638VRD-RA2BE181JYX 1801/8WCarbon AA
R639VRD-RM2HD271JYX 2701/2WCarbon AA
R642VRN-RL3DB2R2J+X 2.22WM-FilmAB
R661VRD-RA2BE102JYX 1k1/8WCarbon AA
R662VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R701VRW-KQ3NC1R5KX 1.57WCement AC
R702VRD-RM2HD154JYX 150k1/2WCarbon AA
R704VRD-RA2BE101JYX 1001/8WCarbon AA
U R705VRN-RL3DBR47J+X 0.472WM-FilmAB
28
Page 29
21FL96
Ref. No. Part No. Description Code
PWB-A: DUNTKC522WEB0
MAIN UNIT
RESISTORS
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
U R706 VRN-RL3DBR39J+ X 0.39 2W M-Film AB
R710VRD-RM2HD220JYX 221/2WCarbon AA
R711VRD-RA2EE122JYX 1.2k1/4WCarbon AA
R712VRD-RA2BE102JYX 1k1/8WCarbon AA
R713VRD-RA2BE102JYX 1k1/8WCarbon AA
R725VRD-RM2HD821JYX 8201/2WCarbon AA
R726VRN-RL2HCR47J+X 0.471/2WM-FilmAB
R753VRD-RM2HD124JYX 120k1/2WCarbon AA
R754VRN-RL3AB8R2J+X 8.21WM-FilmAB
R756VRS-RG3DB121J+X 1202WM-Ox.AB
R801VRS-CY1JF561JYX 5601/16WM-Ox.AA
R802VRS-CY1JF682JYX 6.8k1/16WM-Ox.AA
R803VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R804VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R805VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R806VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R807VRS-CY1JF222JYX 2.2k1/16WM-Ox.AA
R808VRD-RA2BE273JYX 27k1/8WCarbon AA
R812VRS-CY1JF101JYX 1001/16WM-Ox.AA
R814VRS-CY1JF473JYX 47k1/16WM-Ox.AA
R815VRS-CY1JF473JYX 47k1/16WM-Ox.AA
R816VRS-CY1JF223JYX 22k1/16WM-Ox.AA
R817VRS-CY1JF473JYX 47k1/16WM-Ox.AA
R823VRD-RA2BE101JYX 1001/8WCarbon AA
R824VRD-RA2BE101JYX 1001/8WCarbon AA
R826VRD-RA2BE101JYX 1001/8WCarbon AA
R827VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R828VRS-CY1JF471JYX 4701/16WM-Ox.AA
R829 VRD-RA2BE472JY X 4.7k 1/8W Carbon AA
R830VRS-CY1JF393JYX 39k1/16WM-Ox.AA
R831VRS-CY1JF271JYX 2701/16WM-Ox.AA
R832VRS-CY1JF822JYX 8.2k1/16WM-Ox.AA
R833VRS-CY1JF221JYX 2201/16WM-Ox.AA
R835VRS-CY1JF332JYX 3.3k1/16WM-Ox.AA
R836VRD-RA2BE470JYX 471/8WCarbon AA
R838VRD-RA2BE105JYX 1 M1/8WCarbon AA
R839VRS-CY1JF101JYX 1001/16WM-Ox.AA
R840VRS-CY1JF124JYX 120k1/16WM-Ox.AA
R841VRD-RA2BE821JYX 8201/8WCarbon AA
R842VRS-CY1JF471JYX 4701/16WM-Ox.AA
R843VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R847VRS-CY1JF475JYX 4.7M1/16WM-Ox.AA
R1002 VRS-CY1JF183JYX 18k1/16WM-Ox.AA
R1003 VRS-CY1JF822JYX 8.2k1/16WM-Ox.AA
R1006 VRS-CY1JF822JYX 8.2k1/16WM-Ox.AA
R1007 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1008 VRS-CY1JF183JYX 18k1/16WM-Ox.AA
R1009 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1011 VRD-RA2BE101JYX 1001/8WCarbon AA
R1012 VRD-RA2BE101JYX 1001/8WCarbon AA
R1013 QJUM-0001AJFWYX Jumper WireAA
R1023 VRD-RA2BE271JYX 2701/8WCarbon AA
R1024 VRS-CY1JF101JYX 1001/16WM-Ox.AA
R1027 VRS-CY1JF104JYX 100k1/16WM-Ox.AA
R1031 VRD-RA2BE101JYX 1001/8WCarbon AA
R1032 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1034 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1035 VRD-RA2BE101JYX 1001/8WCarbon AA
R1036 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1037 VRS-CY1JF103JYX 10k1/16WM-Ox.AA
R1038 VRS-CY1JF562JYX 5.6k1/16WM-Ox.AA
R1039 VRS-CY1JF102JYX 1k1/16WM-Ox.AA
R1040 VRS-CY1JF273JYX 27k1/16WM-Ox.AA
C851VCKYPA1HB221K+X 220p50VCeramic AA
C852VCKYPA1HB221K+X 220p50VCeramic AA
C853VCKYPA1HB221K+X 220p50VCeramic AA
C880RC-KZ0153CEZZX 1000p 3kVCeramic AB
C893VCEA0A1CW336M+ X 3316VEL.AA
RESISTORS
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
R849VRD-RA2BE221JYX 2201/8WCarbon AA
R850VRD-RA2BE470JYX 471/8W Carbon AA
R851VRD-RA2BE470JYX 471/8W Carbon AA
R852VRD-RA2BE470JYX 471/8W Carbon AA
R854VRD-RA2BE271JYX 2701/8WCarbon AA
R855VRD-RA2BE271JYX 2701/8WCarbon AA
U R859VRS-VV3DB123JX 12k2WM-Ox.AA
U R861VRS-VV3DB123JX 12k2WM-Ox.AA
U R863VRS-VV3DB123JX 12k2WM-Ox.AA
R864VRD-RA2BE470JYX 471/8W Carbon AA
R876VRD-RA2BE121JYX 1201/8WCarbon AA
R877VRD-RA2BE121JYX 1201/8WCarbon AA
R878VRD-RA2BE121JYX 1201/8WCarbon AA
R880VRD-RM2HD332JYX 3.3k1/2WCarbonAA
R881VRD-RM2HD332JYX 3.3k1/2WCarbonAA
R882VRD-RM2HD332JYX 3.3k1/2WCarbonAA
R889VRD-RA2BE821JYX 8201/8WCarbon AA
R891VRD-RA2BE561JYX 5601/8WCarbon AA
R892VRD-RA2BE391JYX 3901/8WCarbon AA
R894VRD-RA2BE152JYX 1.5k1/8WCarbon AA
R895 VRD-RA2BE561JY X 560 1/8W Carbon AA
C3001VCE9GA1HW475M+ X 4.750VEL.AB
C3002VCKYCY1HB562KYX 5600p 50VCeramic AA
C3003VCQYTA1HM123J+X 0.01250VMylarAA
C3004VCEA0A1HW105M+ X 150VEL.AA
C3005VCEA0A1HW475M+ X 4.750VEL.AA
C3006VCEA0A1CW106M+ X 1016VEL.AA
C3007VCEA0A1HW475M+ X 4.750VEL.AA
C3008VCKYCY1HF103ZYX 0.0150VCeramic AA
C3009VCEA0A1CW227M+ X 22016VEL.AB
C3010VCE9GA1HW475M+ X 4.750VEL.AB
C3011VCEA0A1HW475M+ X 4.750VEL.AA
C3012VCE9GA1HW475M+ X 4.750VEL.AB
C3013VCKYCY1HB272KYX 2700p 50VCeramic AA
C3014VCQYTA1HM473J+X 0.04750VMylarAA
C3015VCEACA1HC335K+X 3.350VEL.AC
C3016VCE9GA1HW475M+ X 4.750VEL.AB
C3017VCEACA1CC106K+X 1016VEL.AC
C3018VCEA0A1HW105M+ X 150VEL.AA
C3019VCEA0A1CW106M+ X 1016VEL.AA
C3020VCEA0A1CW106M+ X 1016VEL.AA
C3021VCEA0A1CW106M+ X 1016VEL.AA
C3022VCEA0A1CW106M+ X 1016VEL.AA
C3023VCKYCY1HF103ZYX 0.0150VCeramic AA
C3024VCKYCY1HF103ZYX 0.0150VCeramic AA
C3025VCKYCY1HF473ZYX 0.04750VCeramic AA
C3026VCKYCY1HF473ZYX 0.04750VCeramic AA
C3030VCQYTA1HM682J+X 6800P 50VMylarAA
C3031VCKYCY1HF682ZYX 6800p 50VCeramic AA
C3034VCEA0A1HW224M+ X 0.2250VEL.AA
C3037VCEA0A1HW335M+ X 3.350VEL.AA
C3038VCEA0A1HW335M+ X 3.350VEL.AA
C3039VCEA0A1HW224M+ X 0.2250VEL.AA
C3042VCKYCY1HB681KYX 680p50VCeramic AA
C3043VCKYCY1HB681KYX 680p50VCeramic AA
C3044VCEA0A1EW476M+ X 4725VEL.AA
C3045VCEA0A1HW335M+ X 3.350VEL.AA
C3046VCEA0A1HW335M+ X 3.350VEL.AA
C3047VCEA0A1HW335M+ X 3.350VEL.AA
C3048VCEA0A1HW335M+ X 3.350VEL.AA
P3007 QPLGZ0610CEZZ X plug 6Pin AC
P3008 QPLGZ0610CEZZ X plug 6Pin AC
P3009 QPLGZ0810CEZZ X plug 32" AD
Ref. No. Part No. Description Code
CABINET PARTS
1CCABAB110WEH3X Front Cabinet Ass'yBH
1-1Not Avairable— Front Cabinet
1-2HBDGB3155CESAX BadgeAF
1-3HDECQA403WJSAX LED, R/C CoverAF
1-4JBTN-A070WJKDX Power ButtonAF
1-5MSPRC0005PEFWX Spring(Power Button)AA
1-6GDORFA015WJKDX DoorAG
1-7MSPRPA012WJFWX Spring (Door)AB
1-8HINDPA194WJSAX Indication PlateAE
1-9GBFL-A007WJZZX Speaker BafferAF
2GCABBA088WJKAX Rear CabinetBC
CABINET PARTS LOCATION
MISCELLANEOUS PARTS
U ACC701 QACCZA050WJPZ X AC Cord AG
VSP1205PB09WA X speaker AN
LHLDK0014PEZZ X AC Cord holder AB
LHLDZ0133PEZZ X Anode Clamp AB
LHLDW1047PEZZ X Holder AB
TCAUH3045GJZZ X caution card AB
QCNW-A871WJZZ X Wire (H) 5 pin AD
QCNW-A872WJZZ X Wire (K) 4 pin AD
QCNW-A873WJZZ X Wire (speaker) AF
XTAS730P12000 X Screw(BTN) AA
XTAS740P16000 X Screw (Cab) AA
XTAS740P20000 X Screw (Cab) AA
QPLGA0017CEZZ X PLUG AC ADAPTOR AE
SUPPLIED ACCESSORIES
RRMCGA257WJSA X Infrared R-C Unit AM
TINS-C482WJZZ X Operation manual AH
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKCC692WJZZ X Packing Case AX
SPAKP0109GJZZ X Lamifoam AF
SPAKXA145WJZZ X Packing foam AQ
SSAKA0101GJZZ X Plastic bag AC
TLABM0005GJZZ X Model Label AC
TLABZA713WJZZ X Label AE
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
QRC0011-L
April. 2006
Modify : SEMEX
Design and Production Information
Design: SEM
Production : SEMEX
J B
SHARP ELECTRONICA MEXICO S. A. DE C. V.
Quality & Reliability Control Center
Blvd. SHARP No. 3510 Parque Industrial Rosarito
Playas de Rosarito, México B. C. 22710
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.