SHARP 21FL94 Diagram

Download

Page 1

SERVICE MANUAL

S64T921FL94//

COLOR TELEVISION

Chassis No. GA-4

21FL94

MODEL

In the interests of user-safety (Required by saf ety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

CONTENTS

» ELECTRICAL SPECIFICATIONS .........................................................................................................1

» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................2

» LOCATION OF USER'S CONTROL .....................................................................................................4

» INSTALLATION AND SERVICE INSTRUCTIONS................................................................................5

» SERVICE MODE ..................................................................................................................................6

» ADJUSTMENT METHOD ...................................................................................................................12

» WAVEFORMS .....................................................................................................................................25

» CHASSIS LAYOUT .............................................................................................................................26

» BLOCK DIAGRAM ..............................................................................................................................27

» DESCRIPTION OF SCHEMATIC DIAGRAM......................................................................................31

» SCHEMATIC DIAGRAMS ...................................................................................................................32

» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................36

» REPLACEMENT PARTS LIST............................................................................................................40

» PACKING OF THE SET ......................................................................................................................46

21FL94

Page

ELECTRICAL SPECIFICATIONS

POWER INPUT....................................... AC 110~220 V, 50/60 Hz

POWER RATING .................................................................... 90W

PICTURE SIZE .......................................... 1,239 cm2 (192sq inch)

CONVERGENCE ............................................................. Magnetic

SWEEP DEFLECTION .................................................... Magnetic

FOCUS .................................................. QFP/UNI-B1 Electrostatic

INTERMEDIATE FREQUENCIES

Picture IF Carrier Frequency ..................................... 45.75 MHz

Sound IF Carrier Frequency...................................... 41.25 MHz

Color Sub-Carrier Frequency .................................... 42.17 MHz

(Nominal)

AUDIO POWER

OUTPUT RATING ........................................4.0 W(RMS) x 2pcs

SPEAKER

SIZE ...................................................................12 x 5 cm, 2pcs

VOICE COIL IMPEDANCE............................. 16 ohm at 400 Hz

ANTENNA INPUT IMPEDANCE

VHF/UHF.....................................................75 ohm Unbalanced

TUNING RANGES

VHF-Channels...............................................................2 thru 13

UHF-Channels ............................................................14 thru 69

CATV Channels ...........................................................1 thru 125

(EIA, Channel Plan U.S.A.)

Specifications are subject to change without prior notice.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

Page 2

21FL94

IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:

WARNING

1. For continued safety, no modification of any circuit should be attempted.

2. Disconnect AC power before servicing.

3. Semiconductor heat sinks are potential shock hazards when the chassis is operating.

4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.

SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE

When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.

2. Replace with tube of the same type number for continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.

X-RADIATION AND HIGH VOLTAGE LIMITS

1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified.

2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically.

3. High voltage should always be kept at the rated value

−no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels.

4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly .

5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry.

6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.

Page 3

IMPORTANT SERVICE SAFETY PRECAUTION

DVM

AC SCALE

1.5k ohm 10W

TO EXPOSED METAL PARTS

CONNECT TO KNOWN EARTH GROUND

(Continued)

21FL94

BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)

Before returning the receiver to the user, perform the following safety checks.

1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc.

3. To be sure that no shock hazard exists, check for leakage current in the following manner.

• Plug the AC cord directly into a 110~220 volt AC outlet, (Do not use an isolation transformer for this test).

• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground.

• Use an AC voltmeter ha ving with 5000 ohm per volt, or higher, sensitivity to measure the A C v oltage drop across the resistor.

• Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.

2345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

SAFETY NOTICE

Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.

Page 4

21FL94

LOCATION OF USER'S CONTROL

Page 5

21FL94

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic

screwdrivers or TV alignment tools.

(2)Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION

The receiver is protected by a 3.15A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.

X-RADIATION PROTECTOR CIRCUIT TEST

After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows:

1. Apply 110~220V AC using a variac transformer for accurate input voltage.

2. Allow for warm up and adjust all customer controls for normal picture and sound.

3. Receive a good local channel.

4. Connect a digital voltmeter to P603 pin3 and make sure that the voltmeter reads 20 ±1.1V.

5. Apply external 27V DC at P603 pin3 by using an external DC supply, TV must be shut off.

6. To reset the protector, unplug the AC cord and mak e a short circuit between P603 pin1 and P603 pin2. Now make sure that normal picture appears on the screen.

7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.

HIGH VOLTAGE CHECK

High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:

1. Connect an accurate high voltage meter between ground and anode of picture tube.

2. Operate receiver for at least 15 minutes at 110~220V AC line voltage, with a strong air signal or a properly tuned in test signal.

3. Enter the service mode and set Y-mute ON by using Service R/C.

4. The voltage should be approximately 28.7kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the v oltage test, make Y-mute off to the normal mode.

Page 6

21FL94

SERVICE MODE

Service Mode Overview

1. Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.

2. Service mode is cleared by entering SERVICE key command during service mode.

3. If key input port (SERVICE) input is LOW, then it is in service mode.

4. During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE is disabled.

5. Service mode can be switched to 4 modes as follows by key input MENU;

Adjustment mode

Setting mode

Check mode

Option mode

6. AFT processing is disabled during service mode. PLL setting data is set to fo data.

7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively in service mode. Energy Save is off.

8. Sleep timer, View timer, on timer and off timer are inactivated in Service mode.

9. Sound is muting in service mode except at Adjustment Items V20, M01, M03, M04, M05, and M06.

First mode of service mode when SERVICE key is pressed.

First mode of service mode when local key CH-UP + VOL-DOWN is pressed after MCU reset.

Page 7

Adjustment Mode Items

No. Item Name IC Register Range Default

V01 SUB-PICTURE 1 Chip CONTRAST 0~127 127 V02 SUB-TINT 1 Chip TINT 0~127 64 V03 SUB-COLOR 1 Chip COLOR 0~127 64 V04 SUB-BRIGHT 1 Chip BRIGHT 0~255 128 V05 SUB-SHARP 1 Chip VIDEO-TONE 0~63 32 V06 V-SHIFT 1 Chip V-SHIFT 0~7 4 V07 H-SHIFT 1 Chip H-PHASE 0~31 16 V08 RF-AGC 1 Chip RF-DELAY 0~127 127 V09 V-SIZE 1 Chip V-SIZE 0~63 32 V10 PIF-VCO 1 Chip VIF-VCO 0~63 32 V11 R-CUTOFF 1 Chip R-CUTOFF 0~255 127 V12 G-CUTOFF 1 Chip G-CUTOFF 0~255 127 V13 B-CUTOFF 1 Chip B-CUTOFF 0~255 127 V14 R-DRIVE 1 Chip R-DRIVE 0~127 64 V15 B-DRIVE 1 Chip B-DRIVE 0~127 64 V16 SUB-COLOR(YUV) 1 Chip COLOR 0~127 64 V17 SUB-TINT(YUV) 1 Chip BASEBAND-TINT 0~127 64 V18 CC-POS MICON CC-POS 0~255 32 V19 SCREEN CUT OFF 1 Chip CUT OFF 0~2 0 V20 SUB-VOL 1 Chip A-ATT 0~127 127

V21 H-VCO 1 Chip H-VCO 0~7 4 M01 MTS-ATT MTS ATT (MTS) 0~15 10 M02 MTS-VCO MTS VCO (MTS) 0~63 32 M03 MTS-FILTER MTS FILTER (MTS) 0~63 28 M04 MTS-WIDEBAND MTS WIDEBAND (MTS) 0~63 27 M05 MTS-SPECTRAL MTS SPECTRAL (MTS) 0~63 32 M06 SUB-VOL MTS VOL (MTS) 0~63 63

21FL94

Page 8

21FL94

SELF ADJUSTMENT

H-VCO

1. When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.

2. H-FREE(1chip) is set to 1.

3. H-OUT is set by intelligent monitor output.

4. IM input is set as TIM input.

5. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.

6. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.

7. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.

RF-AGC

1. When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.

2. AGC-OUT is set by intelligent monitor output.

3. IM input is set as AD input.

4. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the maximum setting value.

5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.

6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.

7. Intelligent monitor output and IM input mode are recovered.

PIF-VCO

1. When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.

2. VIF-DEF(1chip) is set to 1.

3. AFC is set by intelligent monitor output.

4. IM input is set as AD input.

5. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.

6. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.

7. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.

Page 9

Setting Mode Items

No. Item Name IC Register Range Default

F01 VIDEO TONE -GAIN (TV) 1 Chips V-TONE 0/1 0 F02 VIDEO TONE -GAIN (AV) 1 Chips V-TONE 0/1 0 F03

VIDEO TONE -GAIN (S-AV) F04 VIDEO TONE -GAIN(YUV) 1 Chips V -T ONE 0/1 0 F05 ABCL 1 Chips ABCL 0/1 0 F06 BS 1 Chips BS-OFF 0/1 0 F07 ABCL-G 1 Chips ABCL-G 0/1 0 F08 SHP-AV OFFSET VIDEO-TONE(OFFSET) -16~+16 0 F09 SHP-SAV OFFSET VIDEO-TONE(OFFSET) -16~+16 0 F10 SHP-YUV OFFSET VIDEO-TONE(OFFSET) -16~+16 0 F11 RGB-CLIP 1 Chips EXTRGB-CLIP 0/1 0 F12 E-SAVE OFFSET CONTRAST(OFFSET) 0~63 30 F13 FAO-VOL 1 Chips A-ATT 0~127 120 F14 PIF-G 1 Chips VIF-GAIN 0~7 4 F15 Y-DELAY(TV) 1 Chips Y-DELAY 0~7 0 F16 Y-DELAY(AV) 1 Chips Y-DELAY 0~7 0 F17 Y-DELAY(SAV) 1 Chips Y-DELAY 0~7 0 F18 Y-DELAY(YUV) 1 Chips Y-DELAY 0~7 0 F19 TINT-AV OFFSET TINT(OFFSET) -32~+32 0 F20 TINT-SAV OFFSET TINT(OFFSET) -32~+32 0 F21 COL-AV OFFSET COLOR(OFFSET) -32~+32 0 F22 COL-SAV OFFSET COLOR(OFFSET) -32~+32 0 F23 R-DRI(R2) OFFSET R-DRI(OFFSET) -32~+32 0 F24 R-DRI( R) OFFSET R-DRI(OFFSET) -32~+32 0 F25 R-DRI(B) OFFSET R-DRI(OFFSET) -32~+32 0 F26 B-DRI(R2) OFFSET B-DRI(OFFSET) -32~+32 0 F27 B-DRI( R) OFFSET B-DRI(OFFSET) -32~+32 0 F28 B-DRI(B) OFFSET B-DRI(OFFSET) -32~+32 0 F29 V-FREE 1 Chips V-FREE 0/1 0 F30 GAMMA 1 Chips GAMMA 0~3 0 F31 TRAP(TV) 1 Chips TRAP-FINE 0~3 2 F32 TRAP(AV) 1 Chips TRAP-FINE 0~3 2 F33 H-FREE 1 Chips H-FREE 0/1 0 F34 1W(TV) 1 Chips V.WINDOW 0/1 0 F35 1W(AV) 1 Chips V.WINDOW 0/1 0 F36 YLPF 1 Chips YSW-LPF 0/1 1 F37 BS-D 1 Chips BS-DISCHARGE 0~3 0 F38 BS-C 1 Chips BS-CHARGE 0~3 0 F39 SL(TV) 1 Chips S-SLICE DOWN 0~3 0 F40 SL(AV) 1 Chips S-SLICE DOWN 0~3 0 F41 SL(SAV) 1 Chips S-SLICE DOWN 0~3 0 F42 SL(YUV) 1 Chips S-SLICE DOWN 0~3 0 F43 AFC2 1 Chips AFC2-G 0/1 0 F44 VD(TV) 1 Chips VSYNC-DET 0/1 0 F45 VD(AV) 1 Chips VSYNC-DET 0/1 0 F46 AS(TV) 1 Chips AUTO-SLICE 0/1 0 F47 AS(AV) 1 Chips AUTO-SLICE 0/1 0 F48 AS(SAV) 1 Chips AUTO-SLICE 0/1 0 F49 AS(YUV) 1 Chips AUTO-SLICE 0/1 0 F50 FBP(TV) 1 Chips FBP VTH 0/1 0 F51 FBP(AV) 1 Chips FBP VTH 0/1 0 F52 FBP(SAV) 1 Chips FBP VTH 0/1 0 F53 FBP(YUV) 1 Chips FBP VTH 0/1 0 F54 C.CLIP LEVEL 1 Chips C.CLIP LEVEL 0/1 0

1 Chips V-TONE 0/1 0

21FL94

Page 10

21FL94

Setting Mode Items (Continued)

No. Item Name IC Register Range Default

F55 PSW MTS PSW 0/1 0 F56 FAO-VOL MTS VOL 0~63 60 F57 CP PLL CHARGE PUMP 0/1 0 F58 CC LEVEL MICON CC LEVEL 0/1 0 F59 OSD POS MICON OSD POS 0/1 0 F60 OFFSET-ADJ-COL 1 Chips COLOR -32~+32 0 F61 OFFSET-ADJ-TINT 1 Chips TINT -32~+32 0 F62 OFFSET-ADJ-TINT-YUV 1 Chips BASEBAND-TINT -32~+32 0 F63 TIMER4-LOW SPEED 1 Chips TIMER4 VALUE 0~225 50 F64 TIMER4-HIGH SPEED 1 Chips TIMER4 VALUE 0~225 125 F65 R-CUT-YUV 1 Chips R-CUT(OFFSET) -63~+63 0 F66 G-CUT-YUV 1 Chips G-CUT(OFFSET) -63~+63 0 F67 B-CUT-YUV 1 Chips B-CUT(OFFSET) -63~+63 0 F68 R-DRI-YUV 1 Chips R-DRI(OFFSET) -63~+63 0 F69 B-DRI-YUV 1 Chips B-DRI(OFFSET) -63~+63 0 F70 CLOCK-ADJ 1 Chips 0~25 25

Page 11

Option Mode Items

21FL94

No 001 DEMO Without DEMO With DEMO 1 002 DOWNLOAD Without V-CHIP OP With V-CHIP OP 0 003 V -CHIP Without V-CHIP With V-CHIP 0 004 SPEAKER Without SPEAKER With SPEAKER 1 005 FAO Without FAO With FAO 1 006 P.PREF Without P.REF With P.REF 1 007 UNIV+ Without UNIV+ With UNIV+ 1 008 VIEW TIMER Without VIEW TIMER With VIEW TIMER 1 009 EZ-SETUP EZ-SETUP A UTO PRESET 0 010 PON-CH Without POWER-ON With POWER-ON 0 011 FAV-COL FAV-COL COL-TEMP 1 012 COMPONENT Without COMPONENT With COMPONENT 1 013 AV Without AV With AV 1 014 AV2 AV1 system AV2 system 1 015 MTS Without MTS With MTS 1 016 TONE-CTRL Without S-ADJ With S-ADJ 1 017 AUTO-OFF Without AUTO-OFF With AUTO-OFF 1 018 INIT-LANG ENGLISH SPANISH 1 019 SETUP-FLAG NO SET UP AUTO SET UP 1 020 AV-FR 021 AV3/S-IN Without AV3/S-IN With AV3/S-IN 0 022 COMB Without COMB With COMB 0 023 AUTO-INPUT Without AUTO-INPUT With AUTO-INPUT 1 024 CLOCK Without CLOCK With CLOCK 1 025 LED SEMEX MODEL SPC MODEL 0 026 FLAT Not FLAT MODEL FLAT MODEL 1 027 BASS BOOST Without BASS BOOST With BASS BOOST 0 028 DSE Without DSE With DSE 0 029 SRS Without SRS With SRS 0

030 WHITE-OUT Without WHITE-OUT With WHITE-OUT 1

OPTION FUNCTION

"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT

Default Data

Check Mode

Micron mask version, software version and ROM correction function status are displayed in check mode.

Page 12

21FL94

ADJUSTMENT METHOD

Caution:to get into the service mode, one of the ways is press direct key for service items. the other ways

is short the main chassis JA301 and JA410

There is three stage of Service Mode data

First stage data from V01 ~ M06 to go into second stage of service mode data, press MENU key Second stage data from F01 ~ F70 to go into third stage of service mode data, press MENU key

Third stage data from 001 ~ 030 Below is the contents of these data First Stage

Data Service Mode Function Range Default Data

V01 SUB-PICTURE CONTRAST 0~127 127 V02 SUB-TINT TINT 0~127 64 V03 SUB-COLOR COLOR 0~127 64 V04 SUB-BRIGHT BRIGHT 0~255 128 V05 SUB-SHARP VIDEO-TONE 0~63 32 V06 V-SHIFT V-SHIFT 0~7 4 V07 H-SHIFT H-PHASE 0~31 16 V08 RF-AGC RF-DELAY 0~127 127 V09 V-SIZE V-SIZE 0~63 32 V10 PIF-VCO VIF-VCO 0~63 32 V11 R-CUTOFF R-CUTOFF 0~255 127 V12 G-CUTOFF G-CUTOFF 0~255 127 V13 B-CUTOFF B-CUTOFF 0~255 127 V14 R-DRIVE R-DRIVE 0~127 64 V15 B-DRIVE B-DRIVE 0~127 64 V16 SUB-COLOR(YUV) COLOR 0~127 64 V17 SUB-TINT(YUV) BASEBAND-TINT 0~127 64 V18 CC-POS CC-POS 0~255 32 V19 SCREEN CUT OFF CUT OFF 0~2 0 V20 SUB-VOL A-ATT 0~127 127 V21 H-VCO H-VCO 0~7 4 M01 MTS-ATT ATT (MTS) 0~15 10 M02 MTS-VCO VCO (MTS) 0~63 32 M03 MTS-FILTER FILTER (MTS) 0~63 28 M04 MTS-WIDEBAND WIDEBAND (MTS) 0~63 27 M05 MTS-SPECTRAL SPECTRAL (MTS) 0~63 32 M06 SUB-VOL VOL (MTS) 0~63 63

Auto Adjustment Item

1. H-VCO

2. RF-AGC

3. PIF-VCO

Page 13

Second Stage

Data Service Mode Function Range Default Data

F01 VIDEO TONE -GAIN (TV) V-TONE 0/1 0 F02 VIDEO TONE -GAIN (AV) V-TONE 0/1 0 F03 VIDEO TONE -GAIN (S-AV) V-TONE 0/1 0 F04 VIDEO TONE -GAIN(YUV) V -T ONE 0/1 0 F05 ABCL ABCL 0/1 0 F06 BS BS-OFF 0/1 0 F07 ABCL-G ABCL-G 0/1 0 F08 SHP-AV VIDEO-TONE(OFFSET) -16~+16 0 F09 SHP-SAV VIDEO-T ONE(OFFSET) -16~+16 0 F10 SHP-YUV VIDEO-TONE(OFFSET) -16~+16 0 F11 RGB-CLIP EXTRGB-CLIP 0/1 0 F12 E-SAVE CONTRAST(OFFSET) 0~63 30 F13 FAO-V OL A-A TT 0~127 120 F14 PIF-G VIF-GAIN 0~7 4 F15 Y -DELAY(TV) Y -DELAY 0~7 0 F16 Y -DELAY(AV) Y-DELA Y 0~7 0 F17 Y -DELAY(SAV) Y-DELA Y 0~7 0 F18 Y -DELAY(YUV) Y-DELAY 0~7 0 F19 TINT -A V TINT(OFFSET) -32~+32 0 F20 TINT -SA V TINT(OFFSET) -32~+32 0 F21 COL-AV COLOR(OFFSET) -32~+32 0 F22 COL-SAV COLOR(OFFSET) -32~+32 0 F23 R-DRI(R2) R-DRI(OFFSET) -32~+32 0 F24 R-DRI( R) R-DRI(OFFSET) -32~+32 0 F25 R-DRI(B) R-DRI(OFFSET) -32~+32 0 F26 B-DRI(R2) B-DRI(OFFSET) -32~+32 0 F27 B-DRI( R) B-DRI(OFFSET) -32~+32 0 F28 B-DRI(B) B-DRI(OFFSET) -32~+32 0 F29 V-FREE V-FREE 0/1 0 F30 GAMMA GAMMA 0~3 0 F31 TRAP(TV) TRAP-FINE 0~3 2 F32 TRAP(AV) TRAP-FINE 0~3 2 F33 H-FREE H-FREE 0/1 0 F34 1W(TV) V.WINDOW 0/1 0 F35 1W(AV) V.WINDOW 0/1 0 F36 YLPF YSW-LPF 0/1 1 F37 BS-D BS-DISCHARGE 0~3 0 F38 BS-C BS-CHARGE 0~3 0 F39 SL(TV) S-SLICE DOWN 0~3 0 F40 SL(AV) S-SLICE DOWN 0~3 0 F41 SL(SAV) S-SLICE DOWN 0~3 0 F42 SL(YUV) S-SLICE DOWN 0~3 0 F43 AFC2 AFC2-G 0/1 0 F44 VD(TV) VSYNC-DET 0/1 0 F45 VD(AV) VSYNC-DET 0/1 0 F46 AS(TV) AUTO-SLICE 0/1 0 F47 AS(AV) AUTO-SLICE 0/1 0 F48 AS(SAV) AUTO-SLICE 0/1 0 F49 AS(YUV) AUTO-SLICE 0/1 0 F50 FBP(TV) FBP VTH 0/1 0 F51 FBP(AV) FBP VTH 0/1 0 F52 FBP(SAV) FBP VTH 0/1 0 F53 FBP(YUV) FBP VTH 0/1 0 F54 C.CLIP LEVEL C.CLIP LEVEL 0/1 0 F55 PSW PSW 0/1 0 F56 FAO-VOL VOL 0~63 60

21FL94

Page 14

21FL94

Second Stage (Continued)

Data Service Mode Function Range Default Data

F57 CP CHARGE PUMP 0/1 0 F58 CC LEVEL CC LEVEL 0/1 0 F59 OSD POS OSD POS 0/1 0 F60 OFFSET-ADJ-COL COLOR -32~+32 0 F61 OFFSET-ADJ-TINT TINT -32~+32 0 F62 OFFSET-ADJ-TINT-YUV BASEBAND-TINT -32~+32 0 F63 TIMER4-LOW SPEED TIMER4 VALUE 0~225 50 F64 TIMER4-HIGH SPEED TIMER4 VALUE 0~225 125 F65 R-CUT-YUV R-CUT(OFFSET) -63~+63 0 F66 G-CUT-YUV G-CUT(OFFSET) -63~+63 0 F67 B-CUT-YUV B-CUT(OFFSET) -63~+63 0 F68 R-DRI-YUV R-DRI(OFFSET) -63~+63 0 F69 B-DRI-YUV B-DRI(OFFSET) -63~+63 0 F70 CLOCK-ADJ 0~25 25

Third Stage

Data OPTION FUNCTION DATA = "0" DATA ="1" Default Data

001 DEMO DEMO DISABLE ENABLE 1 002 DOWNLOAD V-CHIP OP DISABLE ENABLE 0 003 V-CHIP V-CHIP DISABLE ENABLE 0 004 SPEAKER SPEAKER DISABLE ENABLE 1 005 FAO FAO DISABLE ENABLE 1 006 P.PREF P.REF DISABLE ENABLE 1 007 UNIV+ UNIV+ DISABLE ENABLE 1 008 VIEW TIMER VIEW TIMER DISABLE ENABLE 1 009 EZ-SETUP EZ-SETUP AUTO PRESET 0 010 * PON-CH POWER-ON DISABLE ENABLE 0 011 FAV-COL FAV-COL COL-TEMP 1 012 COMPONENT COMPONENT DISABLE ENABLE 1 013 AV AV DISABLE ENABLE 1 014 AV2 AV1 AV2 1 015 MTS MTS DISABLE ENABLE 1 016 TONE-CTRL S-ADJ DISABLE ENABLE 1 017 AUTO-OFF AUTO-OFF DISABLE ENABLE 1 018 INIT-LANG ENGLISH SPANISH 1 019 SETUP-FLAG NO SET UP AUTO SET UP 1 020 AV-FR 021 AV3/S-IN AV3/S-IN DISABLE ENABLE 0 022 COMB COMB DISABLE ENABLE 0 023 AUTO-INPUT AUTO-INPUT DISABLE ENABLE 1 024 CLOCK CLOCK DISABLE ENABLE 1 025 LED SEMEX MODEL SPC MODEL 0 026 FLAT FLAT DISABLE ENABLE 1 027 BASS BOOST BASS BOOST DISABLE ENABLE 0 028 DSE DSE DISABLE ENABLE 0 029 SRS SRS DISABLE ENABLE 0 030 WHITE-OUT WHITE-OUT DISABLE ENABLE 1

"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT

*POWER ON BY CH-UP/CH-DOWN KEY

Page 15

BUS SET UP

21FL94

TINT-OF

B-D(R) B-D(B)

B-D(R2)

–

C-OF

AS(AV) FAO-VOL CP

15-2

B-C-YUV

G-C-YUV

REFER AS BELOW STEP RANGE REFER AS BELOW

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

–

REQUIREMENT

CONTENT

–

21FL94

OSD CHECKING

OUTPUT

INPUT

CONDITION

V05 F15 F16 F19 F21 F23 F24 F25 F26 F27 F28

DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA

SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV R-D(R2) R-D(R) R-D(B)

21FL94 50 5 2 -7 4 +8 +3 -2 -18 -8 +6

FUNCTION

DEF

DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA

GAMMA 1W(AV) SL(TV) SL(AV) VD(TV) AS(TV)

F30 F35 F39 F40 F44 F46 F47 F56 F57 F60 F61

21FL94 1 1 1 1 1 1 1 58 1 +10 +8

FUNCTION

ADJUSTMENT

PROCEDURE

F62 F66 F67

TI-YUV

DEF

21FL94 -12 +36 +2

FUNCTION

LED FLAT BASS DSE SRS WHITE

CLOCK

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

OPTION SET UP

REFER AS BELOW STEP RANGE REFER AS BELOW

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

21FL94

OSD CHECKING

INPUT

CONDITION

OUTPUT

001 002 003 004 005 006 007 008 009 010

DEMO DOWNLOAD V-CHIP SP FAO P.PREF UNIV+ VIEW EZ PON-CH

FUNCTION

21FL94 1 0 0 1 1 1 1 1 0 0

BUS OPTION FOR THIRD STAGE SERVICE DATA

009 → “0”=EZ-SETUP “1”=AUTO PRESET

011 012 013 014 015 016 017 018 019 020

DEF “0”=DISABLE “1”=ENABLE

BUS OPTION FOR THIRD STAGE SERVICE DATA

ADJUSTMENT

PROCEDURE

FAV-COL COMP AV AV2 MTS TONE AUTO LAN SETUP AV-FR

FUNCTION

21FL94 1 1 1 1 1 1 1 1 1 3

AV3 COMB A-IN

021 022 023 024 025 026 027 028 029 030

FUNCTION

21FL94 0 0 1 1 0 1 0 0 0 0

018 → “0”=ENGLISH “1”=SPANISH

019 → “0”=NO SET UP “1”=AUTO SETUP

025 → “0”=SEMEX SPEC “1”=SPC SPEC

DEF 011 → ”0”=FAV-COL “1”=COL-TEMP

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

15-1

Page 16

21FL94

V-SIZE

16-2

V09 STEP RANGE 0~63

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

H-POSITION

C CONTROL

OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST

CONTROL

PRE-ADJUST

REQUIREMENT

US 4 CH LION HEAD

AC 220V

CONFIRMATION BY CRT SCREEN

ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS

CONTENT

INPUT

CONDITION

OUTPUT

SPECIFIED BELOW.

CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE

ADJUSTMENT.

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

OVERSCAN 10 ± 2.5%

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

16-1

V07 STEP RANGE 0-31

OF A=B.

1. ADJUST THE V07 BUS DATA TO HA VE A BALANCE POSITION TO SPEC

2. IF CANNOT MAKE IT T O A=B, ADJ FR OM THE BEST POINT SO THAT

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

C BUS CONTROL I

CONTROL

OPTION SET UP, BUS SET UP, CRT-PURITY

US 4 CH LION HEAD (MONOSCOPE)

AC 220V, US MAGNETIC FIELD

CONFIRMATION BY CRT SCREEN

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

B SLIDELY SMALLER THAN A

[CHECKING SPEC]

ADJUSTMENT

PROCEDURE

LEFT AND RIGHT SYMMETRICAL

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 17

CLOSED CAPTION SET UP

TEXT BOX BLK

V18 STEP RANGE 0~255

21FL94

17-2

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

V-PHASE

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP

US 4 CH LION HEAD

PRE-ADJUST

REQUIREMENT

CONTENT

AC 220V

CONFIRMATION ON CRT DISPLAY.

INPUT

CONDITION

OUTPUT

SPEC OF A=B.

1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED .

2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

LEFT AND RIGHT SYMMETRICAL

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

17-1

V06 STEP RANGE 0-7

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP, CRT-PURITY

US 4 CH LION HEAD (MONOSCOPE PATTERN)

PRE-ADJUST

REQUIREMENT

CONTENT

220V, RF INPUT, ZERO MAGNETIC FIELD

CONFIRMATION ON CRT SCREEN

INPUT

CONDITION

OUTPUT

ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL PO-

SITION.

THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL

POSITION

NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD

ENOUGH

ADJUSTMENT

PROCEDURE

[CHECKING CONFIRMATION]

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 18

21FL94

PIF-VCO

18-2

V10 STEP RANGE 0~63

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

H-VCO

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP

NO SIGNAL (RASTER) CONDITION

AC 220V

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

(AT SELF ADJUSTMENT MODE)

CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).

OUTPUT

1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10

SCREEN

2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT

AS SPECIFIED BELOW

3) IF APPEAR “NG” PLS REPEAT STEP2

(AT MANUAL ADJUSTMENT MODE)

1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10

2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

18-1

V21 STEP RANGE 0-7

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP

NO SIGNAL (RASTER) CONDITION

AC 220V

IC 801 PIN 11

(MANUAL ADJ)

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

1) GO TO SERVICE MODE,

2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW

(SELF ADJ)

1) GO TO SERVICE MODE,BY SELECTING THE SERVICE DATA V21

2) PRESS THE R/C TO OPERATE AUTO H-VCO,OSD APPEAR "OK" AT

SCREEN

3) IF APPEAR "NG" PLS REPEAT STEP2

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

FREQ = 15.735 ± 0.2 KHz

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 19

SCREEN

21FL94

19-2

V11,V12,V13 STEP RANGE 0-255

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

RF-AGC

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP

WINDOW PATTERN OR US4CH LION HEAD

PRE-ADJUST

REQUIREMENT

CONTENT

CONFIRMATION ON CRT DISPLAY

220V

INPUT

CONDITION

OUTPUT

64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR

IN CUT-OFF CONDITION

BRIGHT , THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR

IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=R-

1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO

2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW

CUTOFF, V12=G-CUTOFF, V13=B-CUT-OFF, FIX THE DATA OF THE

COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE

OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BE-

COME WHITE.

3) TURN THE SCREEN VR OF FBT SO THA T CUT-OFF LINE JUST DIS-

ADJUSTMENT

APPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE Y -

MUTE SO THAT PICTURE APPEAR IN NORMAL MODE.

[VOLTAGE CONFIRMATION]

PROCEDURE

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

19-1

V08 STEP RANGE 0-127

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP

US10CH HALF COLOR BAR

RF INPUT

FIELD STRENGTH 53dBµV (FIX)

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN.

(AT SELF ADJUSTMENT MODE)

1. GO TO SERVICE MODE

2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC

TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION

3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.

OUTPUT

COME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE.

SURE THERE IS NO NOISE

THAT THERE IS NO CROSS MODULATION BEAT.

(AT MANUAL ADJUSTMENT MODE)

1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BE-

2. CHANGE THE ANTENNA INPUT SIGNAL T O 63-67 dB µV, AND MAKE

3. CHANGE THE ANTENNA INPUT SIGNAL T O 90-95 dBµV T O BE SURE

ADJUSTMENT

PROCEDURE

[VOLTAGE CONFIRMATION]

MAX - 0.1V dc

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 20

21FL94

BLACK

US14

WHITE

BLACK

US14

SUB-BRIGHT

20-2

V04 STEP RANGE 0-255

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

WHITE BALANCE

C CONTROL

OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE

CONTROL

PRE-ADJUST

WINDOW PATTERN

REQUIREMENT

CONTENT

220V

INPUT

CONDITION

CRT SCREEN DISPLAY.

1) LET THE GUN POINT AT BLACK POSITION (AS ATT A CH DRAWING),

OUTPUT

ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN

STEP DOWN MORE 4 STEP

ADJUSTMENT

PROCEDURE

[VOLTAGE CONFIRMATION]

BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

20-1

V14,V15,V11,V12,V13 STEP RANGE 0-127, 0~255

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

C BUS CONTROL I

CONTROL

OPTION SET UP, BUS SET UP, SCREEN

23CH 501RE WINDOW PATTERN

PRE-ADJUST

REQUIREMENT

CONTENT

220V

CRT SCREEN DISPLAY.

INPUT

CONDITION

OUTPUT

ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN

LET THE GUN POINT AT WHITE POSITION (AS DRAWING A TTACH),

FIRST LET THE GUN POINT AT BLACK POSITION (AS DRAWING

1) WHITE (HIGH BEAM)

ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST

THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS

OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280

AW AY FROM THE DAT A ADJUSTED IN STEP 1), ADJUST AGAIN THE

TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST

LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED

2) BLACK (LOW BEAM)

ADJUSTMENT

SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.

THIS ADJUSTMENT.

*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING

PROCEDURE

**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.

[CHECKING CONFIRMATION]

X=0.273, Y=0.280 (11,600°K + 1 MPCD)

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 21

US14

WHITE

SUB-TINT

V02 STEP RANGE 0-127

B-AMP BASE (TP853)

MUST BE IN STEPPING

LEVEL

21FL94

21-2

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

SUB-PICTURE

C CONTROL I

CONTROL

OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC

US 10 CH HALF COLOR BAR PATTERN

PRE-ADJUST

REQUIREMENT

CONTENT

220V

B-AMP TR BASE (TP853)

CONFIRRM WITH OSCILLOSCOPE

INPUT

CONDITION

OUTPUT

1) GET IN Y-MUTE FUNCTION BY R/C.

2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.

3) DISABLE THE Y -MUTE

**PLS TAKE NOTE THAT SERVICE MODE DATA F61 NEED TO SET +8

ADJUSTMENT

PROCEDURE

[CONFIRMATION]

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

21-1

ADJUSTMENT

ITEM

ADJUSTMENT

V01 STEP RANGE 0-127

C BUS CONTROL

POSITION

CONTROL

THE SPEC

ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2.

1) LET THE GUN POINT AT WHITE POSITION (AS A TTACH DRAWING),

OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS

WINDOW PATTERN

220V

CRT SCREEN DISPLAY.

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH

ADJUSTMENT

PROCEDURE

[VOLTAGER CONFIRMATION]

BRIGHTNESS Y=150 cd/m2

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 22

21FL94

100% WHITE

WY RBMg

Cy G

X-RAY PROTECTION OPERATING CONFIRMATION

–

22-2

– STEP RANGE –

26± 1.1V DC 27V

TP VOLT AGE OPERATION V OLT AGE

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

SUB-COLOR

CONTROL

PRE-ADJUST

AFTER ALL ADJUSTMENT FINISHED.

US 4 CH LION HEAD (MONOSCOPE PATTERN)

REQUIREMENT

CONTENT

AC 220V, RF INPUT

CONFIRMATION BY THE CRT

INPUT

CONDITION

OUTPUT

SET THE USER CONTROL TO SHIPMENT POSITION.

[VOLTAGE CONFIRMATION]

CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.

[OPERATION CONFIRMATION]

SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PRO-

TECTOR IS FUNCTIONED.

HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.

[RECOVER INFORMATION]

PULL OUT THE AC CORD.

[CAUTION]

FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC

CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUG-

ADJUSTMENT

PROCEDURE

GING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN

RESET.)

[VOLTAGE CONFIRMATION]

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

22-1

V03 STEP RANGE 0-127

C BUS CONTROL

OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TNT

US 10 CH HALF COLOR BAR PATTERN

220V

R-AMP TR BASE (TP851)

CONFIRRM WITH OSCILLOSCOPE

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

OF COLOR BAR BEAT AT THE SAME LEVEL

1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW

2) THIS W AVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS

*PLEASE TAKE NOTE THAT SERVICE DATA F60 MUST SET TO +10

ADJUSTMENT

PROCEDURE

[CHECKING CONFIRMATION]

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 23

MS LEVEL ADJUSTMENT

M01 STEP RANGE 0~15

21FL94

23-2

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

HIGH VOL T A GE

C BUS CONTROL

OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC

CONTROL

–

MONORAL SIGNAL (400HZ 100% MODULATION)

PRE-ADJUST

REQUIREMENT

CONTENT

AC 220V, RF INPUT

IC 3001 39 PIN

INPUT

CONDITION

OUTPUT

COME AS SPECIFIED BELOW.

1) SET THE SOUND VOLUME CONTROL MORE THAN 1.

2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BE-

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)

SYMBOL REVISED CONTENT,

HISTOR Y

OF REVISION

23-1

– STEP RANGE –

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

AFTER ALL ADJUSTMENT FINISHED.

US 4 CH LION HEAD (MONOSCOPE PATTERN)

REQUIREMENT

CONTENT

AC 220V, RF INPUT

CRT ANODE VOLTAGE

INPUT

CONDITION

OUTPUTΩ

HIGH VOL T A GE

SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH

ON Y-MUTE BY R/C CONFIRM THE V OLTAGE OF CRT ANODE BY HIGH

VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.

BELOW 30kV

ADJUSTMENT

PROCEDURE

[CAUTION POINT]

USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/

DHHS STANDARD TO MAKE CORRECTION AND CONTROL.

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

Page 24

21FL94

24-2

SEPARTION ADJUSTMENT

M04, M05 STEP RANGE 0~63

C BUS CONTROL

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER

STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz

SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz

PRE-ADJUST

REQUIREMENT

CONTENT

RF INPUT

IC 3001 39 PIN

INPUT

CONDITION

OUTPUT

BECOME MINIMUM LEVEL.

AGE OF 39 PIN BECOME MINIMUM LEVEL.

1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNTIL THE OF 39 PIN

2) INPUT SIGNAL 2, ADJUST BUS DATA OF M05 UNTIL THE AC VOLT-

3) REPEAT STEP 1) AND 2).

SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE

READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC

AS SPECIFIED BELOW.

ADJUSTMENT

PROCEDURE

[CHECKING SPEC]

OVER 25 dB (CHECKING SPEC : OVER 20 dB)

SYMBOL REVISED CONTENT,

HISTORY

OF REVISION

24-1

Page 25

WAVEFORMS

21FL94

Page 26

21FL94

CHASSIS LAYOUT

654321

Page 27

654321

21FL94

CRT BLOCK DIAGRAM

Page 28

21FL94

MAIN BLOCK DIAGRAM

12345678910

Page 29

21FL94

10 11 12 13 14 15 16 17 18 19

Page 30

21FL94

MTS BLOCK DIAGRAM

12345678910

Page 31

DESCRIPTION OF SCHEMATIC DIAGRAM

21FL94

NOTES:

1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ)

2. All resistors are 1/16 watt, unless otherwise noted.

3. All capacitors are µF, unless otherwise noted. (P=pF=µµF)

4. (G) indicates ±2% tolerance may be used.

5. indicates line isolated ground.

VOLTAGE MEASUREMENT CONDITIONS:

1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set f or normal picture unless otherwise indicated.

2. All voltages measured with 1000µV B & W or Color signal.

WAVEFORM MEASUREMENT CONDITIONS:

Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control.

2. indicates waveform check points (See chart, waveforms are measured from point indicated to

chassis ground.)

AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS.

MARK= X-RAY RELATED PARTS.

DRGANNES MARQUES åET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ç : PIECS RELATIVE AUX RAYONS X.

This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.

Page 32

21FL94

SCHEMATIC DIAGRAM: MAIN Unit

12345678910

Page 33

21FL94

10 11 12 13 14 15 16 17 18 19

Page 34

21FL94

SCHEMATIC DIAGRAM: CRT Unit

654321

Page 35

654321

21FL94

SCHEMATIC DIAGRAM: MTS Unit

Page 36

21FL94

PRINTED WIRING BOARD ASSEMBLIES

PWB-A: MAIN Unit (Wiring Side)

654321

Page 37

654321

21FL94

Z1 A1

RJ8

FDC2

R617

R613

RJ15

RJ14

R1027

RJ16

R1024

RJ17

C1016

RJ31

RJ32

R626

R624

R623

R618

R1006

R1008

R1009

R1003

R1007

R303

R714

R1081

R709

Q702

Q701

R707

RJ3

R662

RJ30

Q604

R528

R520

C519

C518

R504

RJ9

R432

R431

IC402

R438

RJ21RJ6

C439

R1002

R314

R315

C313

R305

C308

R307

R308

R1802

R801

Q801

R1043

R1032

C1004

RJ10R1072

IC1003

RJ12

RJ18C1015

R437

R846

IC403

C401

RJ19

C436

RJ2

R462

IC401

Q803

R377

R353

R372

R374

IC305

R378

R363

R458

C453R362

R461

R1083

Q1072

R1079

Q1070

Q1073

R1895

R1896

D801

C808

D810

R840R843

R804

C809

D811

R1851

R1852

D812R805

R806

R1853

C810

RJ29

R807

C814

R1063

R842

Q804

R817

C1009

C1011

C1013

R1064

R1065

C1855

R1066

R1074

R1098R1097

R373

R366

R365

R433

R1056

Q1002

R1085

R1078

R1087

R1849

R827

Q805

R821

R831

C845

R835RJ26

R839

C846

R828

C804

FDC3

R802

C802

C806R1850

R803

IC801

R847

R1062

C815

C816

R812

C819

R816

R814

C821

R832

R815

C823

C826

R1061

C1008

D1086

R1055

R1048

R1047

D1089

D1085

IC1001

R1059

R1096

R1044

R1037

R1036

R1076

R1034

R1033

R1090

R1091

R1038

C1864

C1862R1046

R1867R1049

R1041

C1861

C1863

C205

R1861

R435

R1862

R434

R384

R383

R3006

IC3002

C3081

C839

R833

C847RJ4

C841

C1867

C836

R845

C832

R853C85 3

C833

C831

R844

C830

C828

R1854

C1856

R1077

R301

Q1001

R1039

RJ11

RJ5

R213

IC1007

Q202

R206

Q201

R208

C207

R205

C209

R212

C213R209

C212C1896

RJ27

D202

RJ28

C203

R201

R202

R381

R382

FDC1

RJ24

R3009

RJ23

RJ13

RJ25

RJ20R44 1

R439

R220

C208

R207

R440

RJ22

C210

R210

RJ7

R211

R830

RJ1

PWB-A: MAIN Unit (Chip Parts Side)

Page 38

21FL94

PWB-B: CRT Unit (Wiring Side)

654321

Page 39

654321

21FL94

PWB-C: MTS Unit (Wiring Side)

RJ101

R30 04

R3001

C3031

C3032

C3028

C3033C3026

C3025

C3024

C3023

R3002

C3027

C30 43

R3035

R30 30

R3031

R3032

R3018

R3016

R3015R3033

R3085

Q3007

R3017R3036

R3028

Q30 05

R30 84

R30 82

R3083

Q3006

Q3001

R3027

Q30 02

C3042

R3019

Q3004

R30 29

R3034

R3026

R30 14R3021

R3011

R3007

C3036

R3025

R3005

C3008

C3013

R3008

IC3001

R3012

R3003

C3002

C3035

R3013

R3010

PWB-C: MTS Unit (Chip Parts Side)

Page 40

21FL94

Ref. No. Part No. ★ Description Code

REPLACEMENT PARTS LIST

PARTS REPLACEMENT

Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the following informations.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

MARK : SPARE PARTS-DELIVERY SECTION.

Ref. No. Part No. ★ Description Code

PICTURE TUBE

å L706 RCiLG0069PEZZ X Degaussing Coil AH

VB51QDK191X1E X Picture Tube BV QEARCA012WJZZ X Grounding Strap AC

PRINTED WIRING BOARD ASSEMBLIES

(NOT REPLACEMENT ITEM)

PWB-A DUNTKC522WEA0 - MAIN Unit — PWB-B DUNTKA599WED5 - CRT Unit — PWB-C DUNTKC574WEA0 - MTS Unit —

DUNTKC522WEA0 PWB-A MAIN UNIT

TUNER

NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN

ASSEMBLY NOT INDEPENDENTLY.

å TU201 VTUVT1T5UF202 X VHF Tuner AP

INTEGRATED CIRCUITS

IC301 VHiAN17820B-1 X AN17820B AG IC401 VHiMM1501XN-1Y X MM1501XN AC IC402 VHiMM1501XN-1Y X MM1501XN AC

å IC501 VHiSTV9302A-1 X STV9302A AD

IC601 VHiKA78R09AP1 X KA78R09AP AC

å IC701 VHiSTRW6753-1 X STRW6753 AG å IC702 RH-FXA003WJZZ X FXA003WJ AB å IC703 VHiSE125N++-F X SE125N++ AD

IC801 VHiM61251CF1EQ X M61251CF1 AN IC1001 RH-iXA983WJZZ X IXA983WJ AK IC1003 VHiBR24L04F-1Y X BR24L04F

TRANSISTORS

Q201 VS2SC2735//1EY X 2SC2735 AB Q601 VS2SC2235Y/1E+ X 2SC2235Y Q602 VSTT2140+++-F X TT2140+++ AD Q603 VS2SC3198-G-1+ X 2SC3198-G AB

Ref. No. Part No. ★ Description Code

Q604 VS2SD601AR/-1Y X 2SD601AR AB Q751 VS2SD468-C/-1+ X 2SD468-C AB Q752 VS2SD468-C/-1+ X 2SD468-C AB Q753 VS2SC3198-G-1+ X 2SC3198-G AB Q754 VS2SD468-C/-1+ X 2SD468-C AB Q801 VS2SD601AR/-1Y X 2SD601AR AB Q804 VS2SB709AR/-1Y X 2SB709AR AB Q805 VS2SD601AR/-1Y X 2SD601AR AB Q1001 VS2SD601AR/-1Y X 2SD601AR AB Q1002 VS2SD601AR/-1Y X 2SD601AR AB Q1073 VS2SD601AR/-1Y X 2SD601AR AB

DIODES AND LED

D201 RH-EX0676GEZZY X Zener, EX0676GE AB D203 VHD1SS119//-1Y X 1SS119 AA D392 RH-DX0452CEZZ X DX0452CE D502 RH-EX0652GEZZY X Zener, EX0652GE AB D503 RH-EX0612GEZZY X Zener, EX0612GE AB D505 RH-DX0441CEZZY X DX0441CE AB D510 RH-DX0131CEZZY X DX0131CE AB D601 VHD1SS119//-1Y X 1SS119 AA D602 VHD1SS244//-1Y X 1SS244 AB D603 RH-EX0667GEZZY X Zener, EX0667GE D606 RH-DX0131CEZZY X DX0131CE AB

å D701 RH-DX0476CEZZ X DX0476CE AC

D702 RH-DX0490CEZZY X DX0490CE AB D703 VHD1SS119//-1Y X 1SS119 AA D704 RH-EX0650GEZZY X Zener, EX0650GE AB D705 RH-DX0066GEZZY X DX0066GE AB D706 RH-DX0066GEZZY X DX0066GE AB D707 RH-DX0066GEZZY X DX0066GE AB D708 RH-EX0621GEZZY X Zener, EX0621GE AB D710 VHD1SS119//-1Y X 1SS119 AA D714 VHD1SS119//-1Y X 1SS119 AA D716 RH-EX0601GEZZY X Zener, EX0601GE AB D751 RH-DXA006WJZZ X DXA006WJ AB D752 RH-DX0247CEZZ X DX0247CE D801 RH-EX1393CEZZY X Zener, EX1393CE AB D802 RH-EX0630GEZZY X Zener, EX0630GE AB D803 VHD1SS119//-1Y X 1SS119 AA D806 VHD1SS119//-1Y X 1SS119 AA D810 RH-EX0263TAZZY X Zener, EX0263TA AB D811 RH-EX0263TAZZY X Zener, EX0263TA AB D812 RH-EX0263TAZZY X Zener, EX0263TA AB D1001 RH-PX0013PEZZ X PhotoDiode AB D1081 VHD1SS119//-1Y X 1SS119 AA D1085 RH-EX1393CEZZY X Zener, EX1393CE AB D1086 RH-EX1393CEZZY X Zener, EX1393CE AB D1089 RH-EX1393CEZZY X Zener, EX1393CE AB D1091 VHD1SS119//-1Y X 1SS119 AA D1094 VHD1SS119//-1Y X 1SS119 AA D1095 VHD1SS119//-1Y X 1SS119 AA D1801 VHD1SS119//-1Y X 1SS119 AA VA701 RH-VX0073CEZZ X Varistor AB

PACKAGED CIRCUITS

å PR701 RMPTP0001PEZZ X Packaged Circuit AE å R751 RR-DZ0049CEZZY X Resistor AB å R752 RR-DZ0049CEZZY X Resistor AB

X801 RCRSAA009WJZZ X Crystal, CRSAA009WJ AC

FILTERS

CF201 RFiLC0447CEZZ X Filter, FiLC0447CE AB CF802 RFiLC0446CEZZ X Filter, FiLC0446CE AB SF201 RFiLC0405CEZZ X Filter, FiLC0405CE AD

COILS

L202 VP-CF270K0000Y X Peaking, 27µHAB L203 VP-DF270K0000Y X Peaking, 27µHAB L204 VP-XF1R2K0000Y X Peaking, 1.2µHAB L602 RCiLP0223CEZZ X Coil, 3.3µHAB L701 RCiLFA060WJZZ X Coil, CiLFA060WJ AD L751 RCiLP0179CEZZ+ X Coil, CiLP0179CE AB L801 VP-DF100K0000Y X Peaking, 10µHAB

Page 41

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

21FL94

L802 VP-DF100K0000Y X Peaking, 10µHAB L803 VP-DF100K0000Y X Peaking, 10µHAB L804 VP-XF150K0000Y X Peaking, 15µHAB L806 VP-DF100K0000Y X Peaking, 10µHAB L807 VP-XF1R2K0000Y X Peaking, 1.2µHAB L1861 VP-XF8R2K0000Y X Peaking, 8.2µHAB L1862 VP-XF8R2K0000Y X Peaking, 8.2µHAB

TRANSFORMERS

å T602 RTRNFA095WJZZ X Transformer AR å T603 RTRNZA058WJZZ X Transformer AB å T701 RTRNWA137WJZZ X Transformer

CAPACITORS

C201 VCEA0A1CW476M+X 47 16V Electrolytic AB C202 VCEA0A0JW108M+ X 1000 6.3V Electrolytic AB C203 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C205 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C206 VCEA0A1HW106M+X 10 50V Electrolytic AB C207 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C208 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C209 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C210 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C213 VCKYCY1HB102KYX 1000p 50V Ceramic AA C301 VCEA0A1CW477M+X 470 16V Electrolytic AB C304 VCEA0A1CW106M+X 10 16V Electrolytic AA C308 VCKYCY1HB822KYX 8200p 50V Ceramic AA C310 VCEA0A1HW105M+X 1 50V Electrolytic AB C311 VCEA0A1HW105M+X 1 50V Electrolytic AB C312 VCEA0A1HW224M+X 0.22 50V Electrolytic AB C313 VCKYCY1HB822KYX 8200p 50V Ceramic AA C317 VCE9GA1CW106M+X 10 16V Electrolytic, AB

(N.P) C318 VCEA0A1CW107M+X 100 16V Electrolytic AB C321 VCEA0A1HW224M+X 0.22 50V Electrolytic AB C322 VCEA0A1HW105M+X 1 50V Electrolytic AB C391 VCKYPA1HB102K+ X 1000p 50V Ceramic AA C392 VCQYTA1HM103J+ X 0.01 50V Mylar AB C393 VCEA0A1EW108M+X 1000 25V Electrolytic AB C434 VCE9GA1CW106M+X 10 16V Electrolytic, AB

(N.P) C435 VCE9GA1CW106M+X 10 16V Electrolytic, AB

(N.P) C436 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C437 VCE9GA1HW106M+X 10 50V Electrolytic, AB

(N.P) C438 VCEA0A1CW106M+X 10 16V Electrolytic AA C439 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C452 VCE9GA1CW106M+X 10 16V Electrolytic, AB

(N.P) C505 VCEA0A1HW107M+X 100 50V Electrolytic AB C508 VCFYAA2AA224J+ X 0.22 100V AC C511 VCEA0A1VW477M+X 470 35V Electrolytic AB C512 VCKYPA2HB102K+ X 1000p 500V Ceramic AB C513 RC-EZA332WJZZ+ X Capacitor AB C514 VCFYSA1JB273J+ X 0.027 63V AB C515 VCEACA1HC335J+ X 3.3 50V Electrolytic AB C518 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C601 VCQYTA1HM563J+ X 0.056 50V Mylar AA C602 VCEA0A1HW475M+X 4.7 50V Electrolytic AB C603 VCEA0A1HW105M+X 1 50V Electrolytic AB C604 VCEA0A2EW336M+X 33 250V Electrolytic AB C606 VCKYPA2HB102K+ X 1000p 500V Ceramic AB

å C607 VCFPFD3ZA912H X 9100p 1800V

MetalIzed Polypro Film C608 VCQYTA2AA103K+ X 0.01 100V Mylar C610 VCEA0A1EW227M+X 220 25V Electrolytic AB C611 VCFPVC2DB334J X 0.33 200V AB

MetalIzed Polypro Film C642 VCEA0A1EW476M+X 47 25V Electrolytic AB C643 VCEA0A1AW477M+X 470 10V Electrolytic C650 VCKYPA2HB101K+ X 100p 500V Ceramic AB

å C701 RC-FZ029SCEZZ X Capacitor AB

C702 RC-KZ0029CEZZ+ X 0.01 250V Ceramic AB C703 RC-KZ0029CEZZ+ X 0.01 250V Ceramic AB C704 RC-KZ0029CEZZ X 0.01 250V Ceramic

å C705 RC-EZA097WJZZ X 220 400V AG

C706 VCEA0A1VW226M+X 22 35V Electrolytic AB C708 VCKYPA1HB471K+ X 470p 50V Ceramic AA C709 VCEA9M1HW105M+X 1 50V Electrolytic AA C710 VCFYFA1HA104J+ X 0.1 50V AB C711 VCKYPA1HB681K+ X 680p 50V Ceramic AA C718 VCKYPA2HB472K+ X 4700p 500V Ceramic AB C743 VCKYPH3DB561K X 560p C750 VCKYPA2HB102K+ X 1000p 500V Ceramic AB C751 RC-KZ0106GEZZ X 3300p 250V Ceramic AB C752 VCKYPH3DB561K X 560p 2KV Ceramic AB C753 RC-EZ0724CEZZ X 100 160V Electrolytic AC C754 RC-EZ0638CEZZ X 33 160V Electrolytic AC C755 VCQYTA1HM103J+ X 0.01 50V Mylar AB C756 VCEA0A1EW228M+X 2200 25V Electrolytic C784 RC-KZ0341CEZZ X 1000p 25V C801 VCFYFA1HA105J+ X 1 50V Mylar AB C802 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C803 VCEA9M1CW476M+X 47 16V Electrolytic AA C804 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C805 VCEA0A1HW105M+X 1 50V Electrolytic AB C806 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C807 VCEA0A1CW337M+X 330 16V Electrolytic AB C808 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C809 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C810 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C811 VCEA9M1CW106M+X 10 16V Electrolytic AA C814 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C815 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C816 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C817 VCEA9M1CW107M+X 100 16V Electrolytic AB C818 VCEA9M1HW475M+X 4.7 50V Electrolytic C819 VCCCCY1HH121JYX 120p 50V Ceramic AA C820 VCEA9M1HW474M+X 0.47 50V Electrolytic AA C821 VCKYCY1HF153ZY X 0.015 50V Ceramic AA C822 VCE9GA1HW105M+X 1 50V Electrolytic, AB

C823 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C824 VCEA0A1CW337M+X 330 16V Electrolytic AB C825 VCE9GA1HW105M+X 1 50V Electrolytic, AB

C826 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C827 VCEA0A1CW476M+X 47 16V Electrolytic AB C828 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C829 VCEA9M1CW476M+X 47 16V Electrolytic AA C831 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C833 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C834 VCEA0A1CW107M+X 100 16V Electrolytic AB C835 VCEA0A1CW106M+X 10 16V Electrolytic AA C836 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C837 VCEA9M1HW105M+X 1 50V Electrolytic AA C839 VCCCCY1HH680JY X 68p 50V Ceramic AA C840 VCFYFA1HA105J+ X 1 50V AB C841 VCCCCY1HH101JYX 100p 50V Ceramic AA C842 VCEA9M1HW474M+X 0.47 50V Electrolytic AA C843 VCEA0A1HW105M+X 1 50V Electrolytic AB C845 VCKYCY1CF224ZY X 0.22 16V Ceramic AA C846 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C847 VCCCCY1HH220JY X 22p 50V Ceramic AA C848 VCEA9M1HW105M+X 1 50V Electrolytic AA C1001 VCEA0A1AW107M+X 100 10V Electrolytic AA C1003 VCEA0A1CW106M+X 10 16V Electrolytic AA C1004 VCKYCY1CF474ZY X 0.47 16V Ceramic AB C1006 VCEA0A1HW225M+X 2.2 50V Electrolytic AB C1007 VCEA0A1CW107M+X 100 16V Electrolytic AB C1008 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C1009 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C1011 VCKYCY1HB221KY X 220p 50V Ceramic AA C1012 VCEA0A1HW105M+X 1 50V Electrolytic AB C1013 VCKYCY1HB102KY X 1000p 50V Ceramic AA C1014 VCE9GA1HW475M+X 4.7 50V Electrolytic, AB

C1015 VCCCCY1HH101JY X 100p 50V Ceramic AA C1016 VCKYCY1EF104ZY X 0.1 25V Ceramic AA C1020 VCEA0A0JW477M+ X 470 6.3V Electrolytic AB C1081 VCQYTA1HM104J+ X 0.1 50V Mylar AB

(N.P)

2000V

Ceramic AB

Page 42

21FL94

Ref. No. Part No. ★ Description Code

C1849 VCFYFA1HA223J+ X 0.022 50V AA C1855 VCKYCY1HB561KY X 560p 50V Ceramic AA C1856 VCKYCY1HB102KY X 1000p 50V Ceramic AA C1861 VCCCCY1HH221JY X 220p 50V Ceramic AA C1862 VCKYCY1HB102KY X 1000p 50V Ceramic AA C1863 VCCCCY1HH221JY X 220p 50V Ceramic AA C1864 VCKYCY1HB102KY X 1000p 50V Ceramic AA C1868 VCEA9M1CW336M+X 33 16V Electrolytic

RESISTORS

RJ1 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ3 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ5 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ9 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ10 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ12 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ13 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ14 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ17 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ18 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ19 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ20 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ22 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ25 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ26 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ29 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ30 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA RJ101 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA R201 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R202 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R205 VRS-CY1JF680JY X 68 1/16W Metal Oxide AA R206 VRS-CY1JF122JY X 1.2k 1/16W Metal Oxide AA R207 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R208 VRS-CY1JF331JY X 330 1/16W Metal Oxide AA R209 VRS-CY1JF392JY X 3.9k 1/16W Metal Oxide AA R216 VRS-RG3LB333J+ X 33k 3W Metal Oxide AB R220 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R301 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R302 VRN-RL3DBR10J+ X 0.1 2W Metal Film R303 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA R304 VRD-RA2BE683JY X 68k 1/8W Carbon AA R305 VRS-CY1JF274JY X 270k 1/16W Metal Oxide AA R307 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R308 VRS-CY1JF822JY X 8.2k 1/16W Metal Oxide AA R311 VRD-RA2BE103JY X 10k 1/8W Carbon AA R314 VRS-CY1JF822JY X 8.2k 1/16W Metal Oxide AA R315 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R362 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R363 VRS-CY1JF564JY X 560k 1/16W Metal Oxide AA R365 VRS-CY1JF564JY X 560k 1/16W Metal Oxide AA R366 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R381 VRS-CY1JF564JY X 560k 1/16W Metal Oxide AA R382 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R383 VRS-CY1JF564JY X 560k 1/16W Metal Oxide AA R384 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R431 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R432 VRS-CY1JF750JY X 75 1/16W Metal Oxide AA R433 VRS-CY1JF750JY X 75 1/16W Metal Oxide AA R434 VRS-CY1JF750JY X 75 1/16W Metal Oxide AA R435 VRS-CY1JF750JY X 75 1/16W Metal Oxide AA R436 VRD-RA2BE101JY X 100 1/8W Carbon AA R437 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R438 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA R461 VRS-CY1JF750JY X 75 1/16W Metal Oxide AA R462 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R502 VRS-RG3AB102J+ X 1k 1W Metal Oxide AB R503 VRN-RL3DB1R2J+ X 1.2 2W Metal Film AB R504 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R506 VRS-RG3AB331J+ X 330 1W Metal Oxide AB R507 VRD-RM2HD1R0JY X 1 1/2W Carbon AA R513 VRD-RM2HD333JY X 33k 1/2W Carbon AA R514 VRD-RM2HD682JY X 6.8k 1/2W Carbon AA R520 VRS-CY1JF123JY X 12k 1/16W Metal Oxide AA R524 VRD-RA2BE103JY X 10k 1/8W Carbon AA R525 VRD-RA2BE122JY X 1.2k 1/8W Carbon AA R526 VRD-RA2BE101JY X 100 1/8W Carbon AA

Ref. No. Part No. ★ Description Code

R528 VRS-CY1JF683JY X 68k 1/16W Metal Oxide AA R601 VRD-RM2HD820JY X 82 1/2W Carbon R602 VRD-RA2BE393JY X 39k 1/8W Carbon AA R603 VRD-RA2BE273JY X 27k 1/8W Carbon AA R604 VRD-RA2BE473JY X 47k 1/8W Carbon AA R605 VRD-RM2HD104JY X 100k 1/2W Carbon AA R607 VRD-RM2HD121JY X 120 1/2W Carbon

å R608 VRD-RM2HD102JY X 1k 1/2W Carbon AA

R609 VRD-RM2HD270JY X 27 1/2W Carbon AA

å R611 VRN-RL3AB1R0J+ X 1 1W Metal Film AB å R612 VRD-RM2HD270JY X 27 1/2W Carbon AA

R613 VRS-CY1JF000JY X 0 1/16W Metal Oxide AA R614 VRD-RA2BE154JY X 150k 1/8W Carbon AA R615 VRD-RA2BE102JY X 1k 1/8W Carbon AA R616 VRD-RA2BE102JY X 1k 1/8W Carbon AA R617 VRS-CY1JF123JY X 12k 1/16W Metal Oxide AA R618 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R621 VRN-RL2HC4R7J+ X 4.7 1/2W Metal Film AB R622 VRS-VV3DB682J X 6.8k 2W Metal Oxide AA R631 VRS-KT3LB391J X 390 3W Metal Oxide AB R637 VRD-RA2BE331JY X 330 1/8W Carbon AA R638 VRD-RA2BE181JY X 180 1/8W Carbon AA R639 VRD-RM2HD271JY X 270 1/2W Carbon R642 VRN-RL3DB2R2J+ X 2.2 2W Metal Film R661 VRD-RA2BE102JY X 1k 1/8W Carbon AA R662 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R701 VRW-KQ3NC1R5K X 1.5 7W Cement AB R702 VRD-RM2HD154JY X 150k 1/2W Carbon AA R704 VRD-RA2BE101JY X 100 1/8W Carbon AA

å R705 VRN-RL3DBR47J+ X 0.47 2W Metal Film å R706 VRN-RL3DBR39J+ X 0.39 2W Metal Film

R710 VRD-RM2HD220JY X 22 1/2W Carbon AA R711 VRD-RA2EE122JY X 1.2k 1/4W Carbon AA R712 VRD-RA2BE102JY X 1k 1/8W Carbon AA R713 VRD-RA2BE102JY X 1k 1/8W Carbon AA R725 VRD-RM2HD821JY X 820 1/2W Carbon AA R726 VRN-RL2HCR47J+ X 0.47 1/2W Metal Film AB R753 VRD-RM2HD124JY X 120k 1/2W Carbon AA R754 VRN-RL3AB8R2J+ X 8.2 1W Metal Film AB R756 VRS-RG3DB121J+ X 120 2W Metal Oxide AB R801 VRS-CY1JF561JY X 560 1/16W Metal Oxide AA R802 VRS-CY1JF682JY X 6.8k 1/16W Metal Oxide AA R803 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R804 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R805 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R806 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R807 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R808 VRD-RA2BE273JY X 27k 1/8W Carbon AA R812 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R814 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA R815 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA R816 VRS-CY1JF223JY X 22k 1/16W Metal Oxide AA R817 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA R818 VRD-RS2BE102JY X 1K 1/8W Carbon AA R823 VRD-RA2BE101JY X 100 1/8W Carbon AA R824 VRD-RA2BE101JY X 100 1/8W Carbon AA R826 VRD-RA2BE101JY X 100 1/8W Carbon AA R827 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R828 VRS-CY1JF471JY X 470 1/16W Metal Oxide AA R829 VRD-RA2BE472JY X 4.7k 1/8W Carbon AA R830 VRS-CY1JF393JY X 39k 1/16W Metal Oxide AA R831 VRS-CY1JF271JY X 270 1/16W Metal Oxide R832 VRS-CY1JF822JY X 8.2k 1/16W Metal Oxide AA R833 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R835 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R836 VRD-RA2BE470JY X 47 1/8W Carbon AA R838 VRD-RA2BE105JY X 1M 1/8W Carbon AA R839 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R840 VRS-CY1JF124JY X 120k 1/16W Metal Oxide AA R841 VRD-RA2BE821JY X 820 1/8W Carbon AA R842 VRS-CY1JF471JY X 470 1/16W Metal Oxide AA R843 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R847 VRS-CY1JF475JY X 4.7M 1/16W Metal Oxide AA R1002 VRS-CY1JF183JY X 18k 1/16W Metal Oxide AA R1003 VRS-CY1JF822JY X 8.2k 1/16W Metal Oxide AA R1006 VRS-CY1JF822JY X 8.2k 1/16W Metal Oxide AA

Page 43

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

R1007 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1008 VRS-CY1JF183JY X 18k 1/16W Metal Oxide AA R1009 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1011 VRD-RA2BE101JY X 100 1/8W Carbon AA R1012 VRD-RA2BE101JY X 100 1/8W Carbon AA R1023 VRD-RA2BE271JY X 270 1/8W Carbon AA R1024 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R1027 VRS-CY1JF104JY X 100k 1/16W Metal Oxide AA R1031 VRD-RA2BE101JY X 100 1/8W Carbon AA R1032 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1034 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1035 VRD-RA2BE101JY X 100 1/8W Carbon AA R1036 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1037 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1038 VRS-CY1JF562JY X 5.6k 1/16W Metal Oxide AA R1039 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R1040 VRD-RA2BE273JY X 27k 1/8W Carbon AA R1041 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1042 VRD-RA2BE101JY X 100 1/8W Carbon AA R1043 VRS-CY1JF104JY X 100k 1/16W Metal Oxide AA R1044 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R1045 VRD-RA2BE101JY X 100 1/8W Carbon AA R1046 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R1047 VRS-CY1JF183JY X 18k 1/16W Metal Oxide AA R1048 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R1049 VRS-CY1JF183JY X 18k 1/16W Metal Oxide AA R1051 VRD-RA2BE473JY X 47k 1/8W Carbon AA R1053 VRD-RA2BE101JY X 100 1/8W Carbon AA R1054 VRD-RA2BE101JY X 100 1/8W Carbon AA R1055 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R1056 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R1059 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1061 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R1062 VRS-CY1JF105JY X 1M 1/16W Metal Oxide AA R1063 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1064 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1065 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1066 VRS-CY1JF561JY X 560 1/16W Metal Oxide AA R1072 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R1073 VRD-RA2BE101JY X 100 1/8W Carbon AA R1074 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1076 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R1081 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1087 VRS-CY1JF391JY X 390 1/16W Metal Oxide AA R1096 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1097 VRS-CY1JF472JY X 4.7k 1/16W Metal Oxide AA R1098 VRS-CY1JF104JY X 100k 1/16W Metal Oxide AA R1801 VRD-RA2BE222JY X 2.2k 1/8W Carbon AA R1802 VRS-CY1JF124JY X 120k 1/16W Metal Oxide AA R1849 VRS-CY1JF222JY X 2.2k 1/16W Metal Oxide AA R1850 VRS-CY1JF472JY X 4.7k 1/16W Metal Oxide AA R1851 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R1852 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R1853 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R1854 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R1855 VRD-RA2BE102JY X 1 k 1/8W Carbon AA R1861 VRS-CY1JF121JY X 120 1/16W Metal Oxide AA R1862 VRS-CY1JF121JY X 120 1/16W Metal Oxide AA R1894 VRD-RA2BE103JY X 10k 1/8W Carbon AA R1895 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA R1896 VRS-CY1JF473JY X 47k 1/16W Metal Oxide AA

BALUN

FB601 RBLN-0091GEZZY X Balun, BLN-0091GE

SWITCHES

S1001 QSW-K0202PEZZ+ X Switch, CH-Up AB S1002 QSW-K0202PEZZ+ X Switch, CH-Down AB S1003 QSW-K0202PEZZ+ X Switch, VOL-Up AB S1004 QSW-K0202PEZZ+ X Switch, VOL-Down AB S1005 QSW-K0202PEZZ+ X Switch, MENU AB S1006 QSW-K0114CEZZ X Switch, POWER AC

å FH702 QFSHD1014CEZZ+ X Fuse Holder AB

J401 QJAKGA015WJZZ X Jack, 5Pin AD J402 QJAKE0108CEZZ X Jack, 3Pin AB J403 QJAKE0183CEZZ X Jack, 3Pin AB J404 QJAKE0184CEZZ X Jack, 3Pin AB J405 QJAKG0093CEZZ X Jack, 9Pin AE J406 QJAKFA008WJZZ X Jack, 4Pin AC P302 QPLGN0461CEZZA X Plug, 4Pin (S) AB P601 QPLGN0660CEZZ X Plug, 6Pin (K) AB P602 QPLGN0461CEZZA X Plug, 4Pin AB P603 QPLGN0361CEZZA X Plug, 3Pin (TP651-3) AB P701 QPLGN0260CEZZ X Plug, 2Pin (M) AB P702 QPLGN0269GEZZ X Plug, 2Pin AB P1001 QPLGN0561CEZZA X Plug, 5Pin AB P1002 QPLGN0561CEZZ X Plug, 5Pin (BC) AA RDA301 PRDARA121WJFW X Heat Sink, IC301 AB RDA501 PRDARA120WJFW X Heat Sink, IC501 AB RDA601 PRDARA131WJFW X Heat Sink, IC601 RDA602 PRDAR0337PEFW X Heat Sink AB RDA701 PRDARA119WJFW X Heat Sink, IC701 AC RMC1001

å RY701 RRLYJA006WJZZ X Relay AC

RRMCUA009WJZZ X Remote Receiver AC LHLDP1066PE00 X Holder AB

DUNTKA599WED5

PWB-B CRT UNIT

Q853 VS2SC3789//2E X 2SC3789 AB Q854 VS2SC3789//2E X 2SC3789 AB Q855 VS2SC3789//2E X 2SC3789 AB Q894 VS2SA1015Y/1E+ X 2SA1015Y AB

D859 VHD1SS119//-1Y X 1SS119 AA D898 VHD1SS119//-1Y X 1SS119 AA

L851 VP-MK820K0000+ X Peaking, 82µHAB

C851 VCKYPA1HB221K+ X 220p 50V Ceramic AA C852 VCKYPA1HB221K+ X 220p 50V Ceramic AA C853 VCKYPA1HB221K+ X 220p 50V Ceramic AA C880 RC-KZ0153CEZZ X 1000p 3KV Ceramic AB C893 VCEA0A1CW336M+X 33 16V Electrolytic AA

R849 VRD-RA2BE221JY X 220 1/8W Carbon AA R850 VRD-RA2BE470JY X 47 1/8W Carbon AA R851 VRD-RA2BE470JY X 47 1/8W Carbon AA R852 VRD-RA2BE470JY X 47 1/8W Carbon AA R854 VRD-RA2BE271JY X 270 1/8W Carbon AA R855 VRD-RA2BE271JY X 270 1/8W Carbon AA

å R859 VRS-VV3DB123J X 12k 2W Metal Oxide AA å R861 VRS-VV3DB123J X 12k 2W Metal Oxide AA å R863 VRS-VV3DB123J X 12k 2W Metal Oxide AA

R864 VRD-RA2BE470JY X 47 1/8W Carbon AA R876 VRD-RA2BE121JY X 120 1/8W Carbon AA R877 VRD-RA2BE121JY X 120 1/8W Carbon AA R878 VRD-RA2BE121JY X 120 1/8W Carbon AA R880 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA R881 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA R882 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA R889 VRD-RA2BE821JY X 820 1/8W Carbon AA R891 VRD-RA2BE561JY X 560 1/8W Carbon AA R892 VRD-RA2BE391JY X 390 1/8W Carbon AA R894 VRD-RA2BE152JY X 1.5k 1/8W Carbon AA R895 VRD-RA2BE561JY X 560 1/8W Carbon AA

TRANSISTORS

DIODES

COIL

CAPACITORS

RESISTORS

MISCELLANEOUS PARTS

å F701 QFS-C3229CEZZ X Fuse, T3. 15AL AB

MISCELLANEOUS PARTS

å FH701 QFSHD1013CEZZ+ X Fuse Holder AB

P860 QPLGN0461CEZZ X Plug, 4Pin AA P880 QPLGN0561CEZZ X Plug, 5Pin AA SC851 QSOCV0933CEZZ X Socket, 12Pin AC

21FL94

Page 44

21FL94

Ref. No. Part No. ★ Description Code

DUNTKC574WEA0

PWB-C MTS UNIT

INTEGRATED CIRCUIT

IC3001 VHiCXA2194Q-1Y X CXA2194Q AP

TRANSISTORS

Q3001 VS2SD601AR/-1Y X 2SD601AR AB Q3002 VS2SD601AR/-1Y X 2SD601AR AB Q3004 VS2SD601AR/-1Y X 2SD601AR AB Q3005 VS2SD601AR/-1Y X 2SD601AR AB Q3006 VS2SD601AR/-1Y X 2SD601AR AB Q3007 VS2SD601AR/-1Y X 2SD601AR AB

CAPACITORS

C3001 VCE9GA1HW475M+X 4.7 50V Electrolytic, AB

(N.P) C3002 VCKYCY1HB562KY X 5600p 50V Ceramic AA C3003 VCQYTA1HM123K+X 0.012 50V Mylar AB C3004 VCEA0A1HW105M+X 1 50V Electrolytic AB C3005 VCEA0A1HW475M+X 4.7 50V Electrolytic AB C3006 VCEA0A1CW106M+X 10 16V Electrolytic AA C3007 VCEA0A1HW475M+X 4.7 50V Electrolytic AB C3008 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C3009 VCEA0A1CW227M+X 220 16V Electrolytic AB C3010 VCE9GA1HW475M+X 4.7 50V Electrolytic, AB

(N.P) C3011 VCEA0A1HW475M+X 4.7 50V Electrolytic AB C3012 VCE9GA1HW475M+X 4.7 50V Electrolytic, AB

(N.P) C3013 VCKYCY1HB272KY X 2700p 50V Ceramic AA C3014 VCQYTA1HM473K+X 0.047 50V Mylar AB C3015 VCEACA1HC335K+ X 3.3 50V Electrolytic AB C3016 VCE9GA1HW475M+X 4.7 50V Electrolytic, AB

(N.P) C3017 VCEACA1CC106K+ X 10 16V Electrolytic AB C3018 VCEA0A1HW105M+X 1 50V Electrolytic AB C3019 VCEA0A1CW106M+X 10 16V Electrolytic AA C3020 VCEA0A1CW106M+X 10 16V Electrolytic AA C3021 VCEA0A1CW106M+X 10 16V Electrolytic AA C3022 VCEA0A1CW106M+X 10 16V Electrolytic AA C3023 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C3024 VCKYCY1HF103ZY X 0.01 50V Ceramic AA C3025 VCKYCY1HF473ZY X 0.047 50V Ceramic AB C3026 VCKYCY1HF473ZY X 0.047 50V Ceramic AB C3030 VCQYTA1HM682K+X 6800p 50V Mylar C3031 VCKYCY1HF682ZY X 6800p 50V Ceramic AA C3034 VCEA0A1HW224M+X 0.22 50V Electrolytic AB C3037 VCEA0A1HW335M+X 3.3 50V Electrolytic AA C3038 VCEA0A1HW335M+X 3.3 50V Electrolytic AA C3039 VCEA0A1HW224M+X 0.22 50V Electrolytic AB C3042 VCKYCY1HB681KY X 680p 50V Ceramic AA C3043 VCKYCY1HB681KY X 680p 50V Ceramic AA C3044 VCEA0A1EW476M+X 47 25V Electrolytic AB C3045 VCEA0A1HW335M+X 3.3 50V Electrolytic AA C3046 VCEA0A1HW335M+X 3.3 50V Electrolytic AA C3047 VCEA0A1HW335M+X 3.3 50V Electrolytic AA C3048 VCEA0A1HW335M+X 3.3 50V Electrolytic AA

Ref. No. Part No. ★ Description Code

R3016 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3018 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3019 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3021 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3025 VRS-CY1JF272JY X 2.7k 1/16W Metal Oxide AA R3026 VRS-CY1JF331JY X 330 1/16W Metal Oxide AA R3027 VRS-CY1JF392JY X 3.9k 1/16W Metal Oxide AA R3028 VRS-CY1JF683JY X 68k 1/16W Metal Oxide AA R3029 VRS-CY1JF392JY X 3.9k 1/16W Metal Oxide AA R3030 VRS-CY1JF683JY X 68k 1/16W Metal Oxide AA R3031 VRS-CY1JF182JY X 1.8k 1/16W Metal Oxide AA R3032 VRS-CY1JF223JY X 22k 1/16W Metal Oxide AA R3033 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3034 VRS-CY1JF182JY X 1.8k 1/16W Metal Oxide AA R3035 VRS-CY1JF223JY X 22k 1/16W Metal Oxide AA R3036 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3082 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R3083 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R3084 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA R3085 VRS-CY1JF103JY X 10k 1/16W Metal Oxide AA

MISCELLANEOUS PARTS

P3007 QPLGZ0610CEZZ X Plug, 6Pin AB P3008 QPLGZ0610CEZZ X Plug, 6Pin AB P3009 QPLGZ0810CEZZ X Plug, 8Pin AB

R3001 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA

RESISTORS

R3002 VRS-CY1JF221JY X 220 1/16W Metal Oxide AA R3003 VRS-CY1JF105JY X 1M 1/16W Metal Oxide AA R3004 VRS-CY1JF104JY X 100k 1/16W Metal Oxide AA R3005 VRS-CY1JF623JY X 62k 1/16W Metal Oxide AA R3006 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R3007 VRS-CY1JF332JY X 3.3k 1/16W Metal Oxide AA R3008 VRS-CY1JF302JY X 3k 1/16W Metal Oxide AA R3009 VRS-CY1JF101JY X 100 1/16W Metal Oxide AA R3010 VRS-CY1JF392JY X 3.9k 1/16W Metal Oxide AA R3011 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3012 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3013 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA R3014 VRS-CY1JF102JY X 1k 1/16W Metal Oxide AA

Page 45

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

21FL94

MISCELLANEOUS PARTS

å ACC701 QACCZA020WJPZ X AC Cord AC

SP301 VSP1205PB09WA X Speaker AK

LHLDK0014PEZZ X AC Cord Holder AB LHLDZA096WJZZ X Holder AB LHLDZA107WJZZ X Holder AB TCAUH3045GJZZ X Caution Card AB QCNW-A871WJZZ X Connecting Cord AB QCNW-A872WJZZ X Connecting Cord AC QCNW-A873WJZZ X Connecting Cord AC QPLGA0017CEZZ X Plug AC

SUPPLIED ACCESSORIES

ACCESSORIES

RRMCGA108WJSA X Infrared R-C AT TiNS-B246WJZZ X Operation Manual

PACKING PARTS

(NOT REPLACEMENT ITEM)

SPAKCB318WJZZ - Packing Case — SPAKPA055WJZZ - Wrapping Paper — SPAKXA145WJZZ - Buffer Material — SSAKA0101GJZZ - Polyethylene Bag — TLABM0005GJZZ - Model Label — TLABZA713WJZZ - Label —

CABINET PARTS LOCATION

CABINET PARTS

1 CCABAA596WEH0 X Front Cabinet Ass'y 1-1 Not Avairable - Front Cabinet — 1-2 HBDGB3155CESA X SHARP Badge AD 1-3 HDECQA403WJSA X LED, R/C Cover 1-4 JBTN-A070WJKD X Power Button 1-5 MSPRC0005PEFW X Power Button Spring AA 1-6 GDORFA015WJKD X Door 1-7 MSPRPA012WJFW X Door Spring AB 1-8 HiNDPA194WJSA X Indication Plate AC 1-9 GBFL-A007WJZZ X Speaker Baffer AC 2 GCABBA088WJKA X Rear Cabinet AX

Page 46

21FL94

Ref. No. Part No. ★ Description Code

PACKING OF THE SET

Ref. No. Part No. ★ Description Code

Page 47

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

- M E M O -

21FL94

Page 48

21FL94

Ref. No. Part No. ★ Description Code

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

TQ1756-S

Jun 2004 Printed in Japan

In Japan gedruckt

Design and Production Information Design : SEM Production : SEMEX

MY. DS

SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan