Shark Easy Spray
SK115
OWNER’S GUIDE
™
Steam
WWW.SHARKCLEAN.COM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® Easy
™
STEAM MOP, BASIC SAFETY
Spray
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR SHARK
STEAM MOP.
®
EASY S P R AY
™
DANGER OF SCALDING.
Please use caution when using the steam mop.
The steam emitted from the openings is very
hot.
POLARIZED PLUG:
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature,
this plug will fit into a polarized outlet only
one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
CAUTION:
®
Keep all Shark
reach of children.
Eye irritant. Should some of the Shark
branded cleaners be rubbed or splashed into
the eyes, wash out thoroughly with water. If
irritation continues, contact a physician.
In case of ingestion, drink 16 FL. oz. (2 cups) of
water.
branded cleaners out of the
®
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. Use the system only for its intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance unattended
when plugged in. Always unplug the power
cord from the electrical outlet when not in
use and before servicing.
4. DO NOT allow the appliance to be used
as a toy. Close attention is necessary when
used by or near children, pets or plants.
5.
CAUTION - Shock Hazard. To provide
continued protection against shock,
disconnect from power supply when not in
use.
6. Use only as described in this manual.
7. Use only manufacturer’s recommended
accessories.
8. DO NOT use with damaged cord or
plug. If the appliance is not working as it
should, has been dropped, damaged, left
outdoors, or dropped into water, return
the appliance to EURO-PRO Operating
LLC for examination and repair. Incorrect
re-assembly or repair can cause a risk of
electrical shock or injury to persons when
the appliance is used.
9. To protect against a risk of electric shock,
DO NOT immerse the steam mop into
water or any other liquids.
10. DO NOT handle plug or steam mop with
wet hands or operate appliance without
shoes.
11. DO NOT pull or carry by power cord, use
power cord as handle, close a door on the
power cord, or pull the power cord around
sharp edges or corners. Keep power cord
away from heated surfaces.
TOLL FREE: 1-800-798-7398
12. DO NOT unplug by pulling on power cord.
To unplug, grasp the plug not the power
cord. Do not use extension cords or outlets
with inadequate current carrying capacity.
13. DO NOT put any objects into openings.
Do not use with any opening blocked.
14. DO NOT put hands or feet under the
steam mop. Unit gets very hot.
15. Use ONLY on flat, stable horizontal
surfaces. Do not use on walls, counters,
windows, chairs or tables.
16. DO NOT use on leather, wax polished
furniture or floors, synthetic fabrics, velvet
or other delicate, steam sensitive materials.
17. DO NOT use for space heating purposes.
18. DO NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this
may damage the unit or make it unsafe for
use. If you live in a hard water area, we
recommend using distilled water in your
steam mop.
19. When in use, NEVER turn the appliance
over or on its side. NEVER DIRECT
STEAM TOWARDS PEOPLE,
ANIMALS OR PLANTS.
20. Carefully remove the cleaning pad
immediately after you have unplugged and
allowed the product to cool.
21. When cleaning the steam mop, unplug the
power cord from the electrical outlet and
clean with a dry or damp cloth. Do not
pour water or use alcohol, benzene or paint
thinner on the unit.
22. To reduce the risk of fire, DO NOT use a
flammable or combustible liquid to clean a
floor.
23. Extreme caution should be exercised when
using this appliance to clean stairs.
24. Never use steam mop without a cleaning
pad attached.
25. Keep your work area well lit.
26. Store steam mop indoors in a cool, dry
place.
27. To avoid circuit overload, do not operate
another appliance on the same socket
(circuit) as the steam cleaner.
28. If an extension cord is absolutely
necessary, an extension cord rated a
minimum of 15 ampere, 14 gage cord
should be used. Cords rated for less
amperage may overheat. Care should be
taken to arrange cord so that it cannot be
pulled or tripped over.
29. DO NOT leave unattended when the
system is connected to a power supply
or electrical outlet. Turn off all controls
before unplugging the unit.
30. DO NOT store unit with a damp or wet
cleaning pad attached. Never leave the
steam mop in one spot on any surface for
any period of time with a damp or wet
cleaning pad attached as this will damage
your floors.
WARNING: Your steam mop is
designed to clean hard floor surfaces
that will withstand high heat. Do not use
on unsealed wood or unglazed ceramic
floors. On surfaces that have been treated
with wax or some no wax floors, the
sheen may be removed by the heat and
steam action. It is always recommended
to test an isolated area of the surface
to be cleaned before proceeding. We
also recommend that you check the
use and care instructions from the floor
manufacturer.
SAVE THESE
INSTRUCTIONS
www.sharkclean.com
Thank you for purchasing the Shark® Easy Spray™
Steam Mop.
This Owner’s Guide is designed to help you get a
complete understanding of your new steam mop.
Please read it carefully and keep for future reference.
For a list of what is included with this model, refer to
inside flap of box.
If you should have a question about your Shark® Easy
Spray™ Steam Mop, please call the Shark® Customer
service line at 800-798-7398.
THIS BOOK COVERS MODEL NUMBER:
SK115 11
REGISTER YOUR PURCHASE:
www.sharkclean.com
800.798.7398
RECORD THIS INFORMATION:
Model Number: ________________________
Date of Purchase (Keep receipt): __________
TECHNICAL SPECIFICATIONS:
Voltage: 120V., 60Hz
Watts: 1550W
Water Capacity: 220 ml (7.4 oz.)
RECOMMENDED SCHEDULE FOR REPLACING
CLEANING PADS:
Washable Pads: Every 3 months
FOR BEST CLEANING PERFORMANCE
See Pad Care on page 7 for more detail.
Euro-Pro, Shark, SaniFiber, Easy Spray and Steam
Energized are trademarks of Euro-Pro Operating LLC. All
other brand names may be trademarks of their respective
owners.
TOLL FREE: 1-800-798-7398
When assembling your Shark
®
Easy Spray
TM
steam mop there may be a little water in or around the water
tank. This is because we test all our steam mops 100% before you buy them, so you get a quality Shark®
Easy Spray
TM
Steam Mop.
c
b
a
d
e
PARTS
g
FIRST THINGS FIRST, YOU NEED TO KNOW
WHAT’S IN THE BOX YOU JUST OPENED:
a Upper Extension Tube with Clip
b Lower Extension Tube
c Steam Mop Base
f
d Shark® Steam Energized™ General
Purpose Cleanser
e Washable Cleaning Pad
f SaniFiber
g Filling Flask
™
Disposable Pad (s)
1www.sharkclean.com
ASSEMBLY
fig. 1
fig. 2
YOUR SHARK® EAS Y SPR AY™ STEAM
MOP IS EASY TO ASSEMBLE
1 First remove all the parts from the package. We
know you’re excited about the Shark
™
Spray
Steam Mop, but don’t plug it in until
®
Easy
it’s fully assembled and you’ve read all of the
following instructions.
2 Slide the upper extension tube (the tube with the
handle) into the lower extension tube (the short
tube). Push the two extension tubes together
until you hear it click into place. See illustration
for a visual explanation. (fig. 1)
3 Insert the pieces you assembled in Step 2 into
the pump actuator (the tube that leads to the
tank). Push the extension tube assembly and
pump actuator together in until you hear it click
into place. Insert cord into cord clip on the shaft
of the steam-mop. (fig. 2)
2 TOLL FREE: 1-800-798-7398
IMPORTANT: Always make sure that your
Easy Spray
™
Steam Mop is unplugged from the
wall before you attach a cleaning pad to avoid
damage to your floor and mop.
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended to
test an isolated area of the surface to be cleaned
before proceeding. We recommend that you
check the use and care instructions from the
floor manufacturer.
fig. 3
USE
ATTACHING THE CLEANING PAD
1 Place the
logo side facing up. Place the Easy Spray
cleaning pad on the floor with the
™
Mop on the top of the pad to attach. (fig. 3)
IMPORTANT: Only add water to the tank.
Chemicals or cleaning solutions may be unsafe
or cause damage.
IMPORTANT: Please wait 3-5 minutes for
your Easy Spray
™
Steam Mop to cool off before
removing the cleaning pad.
Steam
NOTE: Don’t be alarmed if the first time
you use your Easy Spray
™
Steam Mop, you
notice water inside the water tank or drops
of water in the packaging. It’s normal to
see this water. Your Easy Spray
™
Steam Mop
was 100% tested in the factory to ensure
your safety and your floor’s happiness. If
you see water in the unit, it’s from these
tests.
Replacement cleaning pads are available
at www.sharkclean.com or by calling
1-80 0 -798-739 8.
3www.sharkclean.com
USE
The water tank cap has an arrow to indicate the locked and unlocked position.
fig. 4
FILLING THE WATER TANK
IM PORTANT: Before you fill up the tank, make
sure your Easy Spray
TM
Steam Mop is unplugged
from the wall.
1 First, remove the water tank cap by turning it
counter clockwise to the unlocked position. See
illustration for a visual explanation. (fig. 4)
4 TOLL FREE: 1-800-798-7398
2 The filling flask included with your Easy
™
Spray
Steam Mop makes filling the water
tank as simple as getting a glass of water
from the sink. Fill the flask with water
and pour it into the tank. Be sure to keep
the water under the MA X FILL line; just
one flask of water is enough for your Easy
™
Spray
Steam Mop. See illustration for a
visual explanation.
3 Replace the water tank cap by turning it
clockwise to the locked position.
Now comes the part you’ve been waiting for – it’s time to use your Easy Spray
™
steam mop. When you
use your steam mop for the first time or haven’t used the unit in awhile, it may take a minute or two
for the water to make its way through the pump and into the heater to create steam. Get it started
by pumping the handle a few times. If you’ve waited a few minutes and you still don’t see any steam,
reference the troubleshooting section on page 8.
USE
fig. 5
IM PORTANT: Your Easy Spray™ Steam Mop
needs water to make steam! Never use your Easy
™
Spray
Steam Mop without water in the tank.
Sweep or vacuum your floors before using your
Easy Spray
™
Steam Mop. Your Easy Spray™ Steam
Mop was designed to get rid of stuck-on gunk,
grime, paw/footprints and it will do a better job
if yesterday’s cereal crumbs aren’t in the way.
Visit www.sharkclean.com for other great
quick cleaning products to complement your
Easy Spray
1
Pull and twist the quick release cord holder to
™
Steam Mop.
unwrap the power cord completely. Plug into an
electrical outlet. The LED light around the Shark
logo will turn on. Success! If your light doesn’t
turn on reference the Troubleshooting section on
page 8.
(fig. 5)
®
5www.sharkclean.com
USE
When your Easy Spray™ Steam Mop stops steaming, it could be out of water. Unplug the
power cord from the electrical outlet and refill the water tank at anytime.
fig. 6
2 Spray the Shark® Steam Energized™ Cleanser
freely on the mess or stain you aim to clean.
(fig. 6)
3 It takes about 30 seconds for the steam to get
going. Now pump the handle a few times to
prime the pump and activate steam.
4 Mop with a forward and backward motion to
customize steam output automatically.
6 TOLL FREE: 1-800-798-7398
(fig. 7)
fig. 7
IM PORTANT: Never leave the Easy Spray
Steam Mop with a damp/wet cleaning pad on
any floor surface for any amount of time as this
may damage the floor.
5 When not using the cleanser, clip the spray
bottle to the handle of the steam mop. The spray
bottle will stay secure during
mop usage.
™
Always remove the cleaning pad from the Easy Spray™ Steam Mop head when you store your
Easy Spray
™
Steam Mop to avoid damage to your floors.
MAINTENANCE
KEEPING YOUR CLEANING PAD AS GOOD
AS NEW
Your steam activated cleaning pad works
wonders for you, so return the favor by giving it
the care it deserves.
1 Wash pads in warm water. Wash separately from
other laundry.
Only use liquid detergent. (no powder detergent)
Don’t use any fabric softeners.
Line dry or dry on a low dryer setting.
2 If there are loose threads on the pad careful cut
the thread with scissors. Don’t pull on them or
cut at the base.
KEEPING YOUR EASY SPRAY
IN TIP-TOP SHAPE
If you love your Easy Spray
show. Caring for your Easy Spray
TM
STEAM MOP
™
Steam Mop, let it
™
Steam Mop
and properly storing it means you’ll get the
same super steam action you expect each time
you use it.
IM PORTANT: Both your Easy Spray
™
Steam Mop
and the water inside it can get very hot, so let it
cool down completely before you store it.
IM PORTANT: Always store the Easy Spray
™
Steam Mop in a safe place away from children
and high traffic areas.
NOTE: It’s a good idea to use distilled water in
your tank to help prolong the life of your Easy
™
Spray
Steam Mop, especially if you live in an
area with hard water.
7www.sharkclean.com
TROUBLESHOOTING
PROBLEM POSSIBLE REASONS & SOLUTIONS
™
The Easy Spray
Steam
Mop will not turn-on.
™
Easy Spray
Steam Mop
will not make steam.
™
Easy Spray
Steam Mop
leaves water on the floor.
™
Easy Spray
Steam Mop
left white spot on the
floor.
Floors are cloudy, streaky
or spotty after steaming.
TM
Easy Spray
Steam Mop
is hard to push.
Your steam-mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
If your unit still doesn’t work, give us a call 1-800-798-7398.
Is there water in the water tank? If not, add water to your Steam Mop
following instructions.
Do not leave the steam mop on the floor with a damp cleaning pad.
If you are using tap water, we recommend switching to distilled water.
Make sure that the cap is securely placed on the water tank.
Check to see if the cleaning pad is soaked through. We recommend that
you unplug the unit and replace the cleaning pad.
The cleaning pad may be dirty. Change cleaning pad.
The mop may have been left in one spot for too long.
This may be leftover from past cleaners used on the floor surface.
Uvse the mop a few more times again with a clean pad and see if the
cloudiness is removed. If this does not work, we suggest rinsing the floor
with water, letting it dry and then steam mopping again with a clean pad.
One of more rinses generally removes the residue. A more stubborn case
may require you to rinse the floor with a mix of one part vinegar and two
parts water.
Make sure the cleaning pad is on properly.
Check to see if the cleaning pad is excessively dirty. If so, replace with a
clean pad.
8 TOLL FREE: 1-800-798-7398
NOTE: Select cleaning accessories are included. Others are available for purchase at www.SharkClean.
com or by calling 800.798.7398.
For a list of what is included with this model, refer to inside flap of box.
ACCESSORY
Shark® Steam Energized™ Cleanser
Combine Steam & Cleanser for a superior level of
cleaning performance.
XSTENER10
Washable Cleaning Pads
Wipes out tough messes. Keeps cleaning room after
room. Lasts up to 20 washes! Unique bumper design
for enhanced edge cleaning.
™
SaniFiber
Disposable Cleaning Pads
P141GHF
The ONLY disposable pads with the cleaning
performance of a washable!
DXT100
ACCESSORIES
9www.sharkclean.com
Notes
10 TOLL FREE: 1-800-798-7398
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, return the complete appliance and accessories, freight prepaid. For Customer
Service support, call 1 (800) 798-7398 or visit our website www.sharkclean.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating
LLC will repair or replace it free of charge. Proof of purchase date and $ 19.95 to cover the cost of
return shipping and handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and does
not apply to any unit that has been tampered with or used for commercial purposes. This limited
warranty does not cover damage caused by misuse, abuse, negligent handling or damage due
to faulty packaging or mishandling in transit. This warranty does not cover damage or defects
caused by or resulting from damages from shipping or repairs, service or alterations to the product
or any of its parts, which have been performed by a repair person not authorized by EURO-PRO
Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is
limited to the specific obligations expressly assumed by it under the terms of the limited warranty.
In no event is EURO-PRO Operating LLC liable for incidental or consequential damages
of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of
incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to
include proof of purchase date and to attach tag to item before packing with
your name, complete address and phone number with a note giving purchase
information, model number and what you believe is the problem with the item.
We recommend you insure the package (as damage in shipping is not covered
by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within
ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number
along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By
registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.
11www.sharkclean.com
EURO-PRO Operating LLC
U.S.: Newto n, MA 02459
Canada: Vill e St. Laurent, Q uébec H4S 1A7
1-8 00 -798-739 8
www.sharkclean.com
COPYRI GHT © 2013 EURO-PRO O PERATING LLC
PRINTED IN CHINA
Euro-Pro, Shark, SaniFiber, Easy Spray and Rotator are trademarks of
Euro-Pro Operating LLC.
SK115. E.131223 .1
Illustrations may differ from actual product.
Loading...