Shark SGP-302517, SGP-303037, SGP-353037, SGP-353037E, SGP-403537E Operator's Manual
OPERATOR’S MAN U AL
MODEL # ORDER #
SGP-302517
SGP-303037
SGP-353037
SGP-353037E
SGP-403537E
To locate your local Shark Commercial Pressure Washer Dealer nearest you,
1.110-059.0
1.110-054.0
1.110-055.0
1.110-056.0
1.110-057.0
visit www.shark-pw.com
9.801-192.0
CONTENTS
Introduction & Important Safety Instructions 3-5
Component Identifi cation 6
Assembly Instructions 7
Operating Instructions 8-9
Detergents and Cleaning Tips 10
Shut-Down and Clean Up 11
Storage 11
Maintenance 12-14
Troubleshooting 15-17
Maintenance & Oil Change Charts 18
Exploded View - 059.0 19
Exploded View - 054.0, 055.0, 056.0, 057.0 20-21
Exploded View Parts Lists 22-25
Control Panel -059.0 & Parts List 26-27
Control Panel - 054.0, 055.0, 056.0, 057.0 & Parts List 28-29
Hose & Spray Gun Assembly & Parts List 30
Downstream Injector Assembly 31
Hose Reel Option 32
UU1 Unloader Exploded View and Parts List 33
KS.2 Pump Exploded View and Parts List 34-35
KG.2 Pump Exploded View and Parts List 36-37
Burner Specifi cations 38
Warranty 39
Model Number ______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal at tached
to the pressure washer. You should record both serial number and
date of purchase and keep in a safe place for future ref er ence.
2
9.801-192.0 • Rev. 02/11
INTRODUCTION & IMPORTANT SAFETY INFORMATION
PRESSURE WASHER
Thank you for purchasing this Pressure Washer.
We reserve the right to make changes at any time
without incurring any obligation.
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this pressure washer. Warning information
should be emphasized and understood. If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with
the operator in the operator’s native language by the
purchaser/owner, making sure that the operator comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
The operator must know how to stop the machine
quickly and understand the operation of all controls.
Never permit anyone to operate the engine without
proper instructions.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts, please specify model and
serial number. Use only identical replacement
parts.
This machine is to be used only by trained operators.
IMPORTANT SAFETY
INFORMATION
WARNING: To reduce the risk of
injury, read operating instructions carefully before using.
1. Read the owner's manual
thoroughly. Failure to follow
instructions could cause mal-
READ OPERATOR’S
MANUAL THOROUGHLY
PRIOR TO USE.
2. Know how to stop the machine and bleed pressure
quickly. Be thoroughly familiar with the controls.
3. Stay alert — watch what you are doing.
WARNING
KEEP WATER
SPRAY AWAY FROM
ELECTRICAL WIRING.
function of the machine and
result in death, serious bodily
injury and/or property damage.
WARNING: Keep wand, hose, and
water spray away from electric
wiring or fatal electric shock may
result.
4. All installations must comply
with local codes. Contact
your electrician, plumber,
utility company or the selling
distributor for specifi c details.
9.801-192.0 • Rev. 02/11
WARNING
WARNING: This machine exceeds
85 db appropriate ear protection
must be worn.
EAR PROTECTION
MUST BE WORN
WARNING
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne
and fl y at high speeds. To avoid
personal injury, eye, hand and
foot safety devices must be
USE PROTECTIVE
EYE WEAR
AND CLOTHING
WHEN OPERATING
THIS EQUIPMENT.
worn.
5. Eye, hand, and foot protection
must be worn when using this
equipment.
6. Keep operating area clear of all persons.
WARNING
WARNING: Flammable liquids
can create fumes which can ignite, causing property damage
or severe injury.
WARNING: Risk of explosion —
RISK OF EXPLOSION:
OPERATE ONLY WHERE
OPEN FLAME OR TORCH
IS PERMITTED
WARNING
Operate only where open fl ame
or torch is permitted.
WARNING: Risk of fi re — Do not
add fuel when the product is
operating or still hot.
WARNING: Do not use gasoline
crankcase draining or oil con-
RISK OF FIRE.
DO NOT ADD FUEL
WHEN OPERATING
MACHINE.
taining gasoline, solvents or
alcohol. Doing so will result in
fi re and/or explosion.
WARNING: Risk of fi re — Do not
Spray fl ammable liquids.
WARNING: This product contains chemicals known
to the state of California to cause cancer and birth
defects or other reproductive harm. Operation of
this equipment may create sparks that can start
fi res around dry vegetation. A spark arrestor may
be required. The operator should contact: Local
fi re agencies for laws or regulations relating to fi re
prevention requirements.
7. Allow engine to cool for 1-2 minutes before refueling. If any fuel is spilled, make sure the area is
dry before testing the spark plug or starting the
engine. (Fire and/or explosion may occur if this is
not done.)
OPERATOR’S MAN U AL
3
IMPORTANT SAFETY INFORMATION
Gasoline engines on mobile or portable equipment
shall be refueled:
a. outdoors;
b. with the engine on the equipment stopped;
c. with no source of ignition within 10 feet of
the dispensing point; and
d. with an allowance made for expansion of the
PRESSURE WASHER
fuel should the equipment be exposed to a
higher ambient temperature.
In an overfi lling situation, additional precautions are
necessary to ensure that the situation is handled
in a safe manner.
WARNING: Risk of injury. Disconnect battery
ground terminal before servicing.
8. When in use , do not place machine near fl ammable
OPERATOR’S MANUAL
objects as the engine is hot.
9. Oil burning appliances shall be installed only in
locations where combustible dusts and fl ammable
gases or vapors are not present. Do not store or
use gasoline near this machine.
10. Use No. 1 or No. 2 heating oil (ASTM D306) only.
NEVER use gasoline in your fuel oil tank. Gasoline
is more combustible than fuel oil and could result
in a serious explosion. NEVER use crankcase or
waste oil in your burner. Fuel unit malfunction could
result from contamination.
11. Do not confuse gasoline and fuel oil tanks. Keep
proper fuel in proper tank.
WARNING
WARNING: Risk of injury. Hot
surfaces can cause burns. Use
only designated gripping areas
of spray gun and wand. Do not
place hands or feet on non-insulated areas of the pressure
RISK OF INJURY.
HOT SURFACES
CAN CAUSE BURNS
washer.
12. Transport/Repair with fuel tank EMPTY or with fuel
shut-off valve OFF.
CAUTION: Hot discharge fluid.
Do not touch or direct discharge
stream at persons.
WARNING: This machine produces hot water and must have
HOT DISCHARGE FLUID:
DO NOT TOUCH OR
DIRECT DISCHARGE
STREAM AT PERSONS.
insulated components attached
to protect the operator.
WARNING
WARNING: Grip cleaning wand
securely with both hands before
starting. Failure to do this could
result in injury from a whipping
wand.
14. Never make adjustments on
machine while in operation.
TRIGGER GUN KICKS
BACK - HOLD WITH
BOTH HANDS
15. Be certain all quick coupler fi ttings are secured
before using pressure washer.
WARNING
WARNING: High pressure developed by these machines will
cause personal injury or equipment damage. Keep clear of
nozzle. Use caution when operating. Do not direct discharge
RISK OF INJECTION
OR SEVERE INJURY
TO PERSONS. KEEP
CLEAR OF NOZZLE.
WARNING
stream at people, or severe injury or death will result.
WARNING: Protect machine from
freezing.
16. To keep machine in best
operating conditions, it is
important you protect machine
from freezing. Failure to protect
PROTECT FROM
FREEZING
machine from freezing
could cause malfunction of the
machine and result in death,
serious bodily injury, and/or property damage. Follow storage instructions specifi ed in this manual.
17. Inlet water must be clean fresh water and no hotter
then 90°F.
WARNING
WARNING: Risk of asphyxiation.
Use this product only in a well
ventilated area.
18. Avoid installing machines in
small areas or near exhaust
RISK OF
ASPHYXIATION: USE
THIS PRODUCT ONLY
IN A WELL
VENTILATED AREA.
fans. Adequate oxygen is
needed for combustion or
dangerous carbon monoxide
will result.
19. Manufacturer will not be liable for any changes
made to our standard machines or any components
not purchased from us.
20. The best insurance against an accident is precaution and knowledge of the machine.
13. To reduce the risk of injury, close supervision is
necessary when a machine is used near children.
Do not allow children to operate the pressure
4
washer. This machine must be attended during
operation.
9.801-192.0 • Rev. 02/11
IMPORTANT SAFETY INFORMATION
PRESSURE WASHER
WARNING
WARNING: Be extremely careful
when using a ladder, scaffolding
or any other relatively unstable
location. The cleaning area
should have adequate slopes
and drainage to reduce the pos-
RISK OF INJURY
FROM FALLS WHEN
USING LADDER.
21. Do not allow acids, caustic or abrasive fl uids to pass
through the pump.
22. Never run pump dry or leave spray gun closed
longer than 1-2 minutes.
23. Machines with shut-off spray gun should not be
operated with the spray gun in the off position for
extensive periods of time as this may cause damage to the pump.
24. Protect discharge hose from vehicle traffi c and
sharp objects. Inspect condition of high pressure
hose before using or bodily injury may result.
25. Before disconnecting discharge hose from water
outlet, turn burner off and open spray gun to allow water to cool below 100° before stopping the
machine. Then open the spray gun to relieve pressure. Failure to properly cool down or maintain the
heating coil may result in a steam explosion.
26. Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
27. Do not operate this machine when fatigued or under
the infl uence of alcohol, prescription medications,
or drugs.
28. In oil burning models, use only kerosene, No. 1
home heating fuel, or diesel. If diesel is used, add
a soot remover to every tankful.
sibility of a fall due to slippery
surfaces.
Follow the maintenance instructions
specifi ed in the manual.
OPERATOR’S MAN U AL
5
9.801-192.0 • Rev. 02/11
COMPONENT IDENTIFICATION
Gasoline
Tank
Discharge
PRESSURE WASHER
OPERATOR’S MANUAL
Nipple
Collar
Detergent
Injector
Quick
Coupler
Spray
Gun
Pressure
Switch
Unloader
Water Supply
Hose
(not included)
Pump
Battery Box
Swivel
Connector
High Pressure
Hose
Trigger
Pump — Develops high pressure.
Starter Grip — (Not Shown) Used for starting the
en gine man u al ly.
Spray Gun — Controls the application of water and
de ter gent onto cleaning surface with trigger device.
In cludes safe ty latch.
Detergent Injector — Allows you to siphon and mix
de ter gents.
6
9.801-192.0 • Rev. 02/11
Wand Coupler
Nozzle
Quick
Coupler
Variable Pressure
Control wand
Control Wand
Handle
Brass
Soap
Nozzle
Variable Pressure Control Wand — Must be con-
nect ed to the spray gun. This wand handle controls
dishcharge flow from one tube to both wand tubes.
When water is discharged from both tubes you will have
a pres sure loss and allows chemical siphoning when
used in combination with a detergent injector.
High Pressure Hose — Connect one end to water
pump dis charge nipple and the other end to spray
gun.
Note: If trigger on spray gun is released for more
than 2 minutes, water will leak from valve. Warm
water will dis charge from pump protector onto floor.
This sys tem pre vents internal pump dam age.
ASSEMBLY INSTRUCTIONS
PRESSURE WASHER
Spray
Gun
Safety
Latch
High Pressure
Hose
STEP 1: Attach the high
pres sure hose to the spray
gun using teflon tape on hose
threads.
DipStick
Oil Window
Soap
Nozzle
Wand
Coupler
STEP 2: Pull the spring-load ed col lar
of the wand coupler back to in sert your
choice of pres sure noz zle.
Discharge Fitting
Coupler Collar
High Pressure Hose
Pressure
Nozzle
Wand
Coupler
Wand
Collar
STEP 3: Release the coupler col lar
and push the nozzle until the collar
clicks. Pull the nozzle to make sure it
is seated properly.
Cold
Water
Source
Garden
Hose
OPERATOR’S MAN U AL
STEP 4: Remove shipping cap
and install oil dipstick. Check
pump oil level by using dip stick
STEP 5: Connect the high pres sure
hose to the pump discharge fitting. Push
cou pler collar forward until secure.
or observe oil level in oil win dow (if equipped). Use 30 wt.
non detergent oil.
Garden
Hose
Pump
Water Inlet
STEP 7: Connect the garden hose
to pump wa ter inlet. In spect inlets.
CAUTION: Do not run the pump
without wa ter or pump damage
will result.
STEP 6: Connect garden hose to the
cold water source.
7
9.801-192.0 • Rev. 02/11
OPERATING INSTRUCTIONS
Oil Dipstick
PRESSURE WASHER
STEP 1: Check engine oil level. Oil level should be level with the bottom
of the oil filler neck. Be sure the ma chine is level when checking the oil
level. (Refer to the en gine's op er at ing manual included with machine.) We
rec om mend that the oil be changed after the first 5 hours of use, then once
every 50 hours. Note: Im prop er oil levels will cause low oil sensor to shut
OPERATOR’S MANUAL
off engine. IMPORTANT! Do not run engine with high or low oil levels
as this will cause engine damage.
Cold
Water
Source
Gas
Tank
STEP 2: Fill gas tank with un lead ed
gasoline. Do not use leaded gas o line. Caution: Read warnings on
pg. 4 and engine manual.
Garden
Hose
STEP 3: Connect garden hose
to the cold water source and turn
wa ter on completely. Never use hot
wa ter.
Fuel
Valve
STEP 4: Trigger the spray gun to
elim i nate trapped air then wait for a
steady flow of water to emerge from
the spray noz zle.
STEP 5: Rotate the fuel shut-off valve to the "On" po si tion. Slide the fuel valve lever to the "ON" position.
When the engine is not in use, leave the fuel valve in
the "OFF" position.
Choke
Lever
STEP 6: Pull the choke lever out to the "Choke" po si tion
(on a warm engine, leave the choke lever in, in the run
po si tion). Push the choke lever to the "Closed" po si tion.
To restart a warm engine, leave the choke lever in the
"Open" position.
8
9.801-192.0 • Rev. 02/11
OPERATING INSTRUCTIONS
Throttle
STEP 7: Turn the engine to "Run" position. STEP 8: Pull the starter grip. If the engine fails to start
after 2 pulls, squeeze the trigger gun to release pres sure
and repeat step. Return start er gently. After the en gine
warms up enough to run smoothly, move choke to run
position and throt tle to fast position.
CAUTION: Small engines may kick back. Do not hold
pull starter grip tightly in hand.
PRESSURE WASHER
OPERATOR’S MAN U AL
Temperature
Gauge
Burner
Swutch
STEP 9: If hot water is required.
Adjust temperature gauge to prop er
temperature (200°). Turn on Burn er
switch to begin heat ing water.
Variable Pressure
Brass Soap
Nozzle
High
Pressure
Nozzle
Variable Pressure
Control Handle
Wand (VP)
Trigger
Safety
Latch
WARNING! Never replace noz zles without engaging the safe ty
latch on the spray gun trig ger.
NOZZLES
The four color-coded quick con nect
noz zles provide a wide array of
spray widths from 0° to 40° and are
easily accessible when placed in
the con ve nient rubber nozzle holder,
which is provided on the front of the
ma chine.
NOTE: For a more gentle rinse,
se lect the white 40° or green 25°
noz zle. To scour the surface, select
the yellow 15° or red 0° nozzle. To
apply de ter gent select the black
noz zle.
Selection of high or low pressure is accompanied by
turn ing the han dle. NOTE: High pressure nozzle must
be in sert ed at end of wand to obtain high pressure. To
apply soap read operator's manual.
9
9.801-192.0 • Rev. 02/11
WARNING
DETERGENTS AND CLEANING TIPS
WARNING: Some de ter gents
may be harm ful if in haled or in gest ed, caus ing severe nau sea,
fainting or poi son ing. The harm ful el e ments may cause prop er ty
dam age or severe injury.
STEP 1: Connect detergent in jec -
PRESSURE WASHER
Connect high pres sure hose to in jec tor with quick
coupler(check to make sure locking coupler sleeves are
in proper position be fore ap ply ing water pressure
Detergent
OPERATOR’S MANUAL
STEP 3: Apply safety latch to spray gun trig ger. Turn
variable pressure control handle until discharge wa ter
exits both tubes. Secure black de ter gent noz zle into
quick cou pler if you have a single wand. NOTE: De ter gent can not be ap plied us ing Red, Yel low, Green or
White noz zles.
the detergent in jec tion sys tem after each use by
plac ing the suction tube into a buck et of clean wa ter, then run the pres sure wash er in low pres sure
for 1-2 min utes.
10
tor to discharge nip ple on ma chine,
Discharge
Nipple
Injector
Control
Handle
High Pressure
Hose
STEP 2: Use detergent de signed
spe cif i cal ly for pres sure washers.
House hold de ter gents could dam age the pump. Pre pare de ter gent
so lu tion as re quired by the man u fac tur er. Fill a con tain er with pres sure wash er de ter gent. Place the
fil ter end of de ter gent suc tion tube
into the de ter gent con tain er.
STEP 4: With the engine run ning,
pull trig ger to op er ate ma chine.
Liq uid detergent is drawn into the
ma chine and mixed with water.
Apply de ter gent to work area.
Do not al low de ter gent to dry on
sur face.
IMPORTANT: You must flush
Quick
Coupler
9.801-192.0 • Rev. 02/11
THERMAL PUMP PROTECTION
If you run the engine on your pres sure wash er for 3-5
min utes with out pressing the trig ger on the spray gun,
cir cu lat ing water in the pump can reach high tem per a tures. When the water reaches this tem per a ture, the
pump pro tec tor engages and cools the pump by dis charg ing the warm water onto the ground. This ther mal
de vice pre vents internal dam age to the pump.
CLEANING TIPS
Pre-rinse clean ing surface with fresh water. Place de ter gent suc tion tube di rect ly into clean ing solution and
ap ply to sur face at low pressure (for best re sults, limit
your work area to sec tions approximately 6’ square
and always ap ply de ter gent from bottom to top). Allow
de ter gent to re main on sur face 1-3 min utes. Do not al low de ter gent to dry on sur face. If sur face appears to
be drying, sim ply wet down sur face with fresh water. If
need ed, use brush to re move stub born dirt. Rinse at
high pres sure from top to bottom in an even sweep ing
mo tion keep ing the spray nozzle ap prox i mate ly 1’ from
cleaning sur face. Use over lap ping strokes as you clean
and rinse any sur face. For best surface clean ing action
spray at a slight an gle.
Recommendations:
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
dis tance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use
ex treme caution as pressure washer may re move
the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
sur face you plan to clean. High pressure wash a
small area, then check the surface for damage. If no
dam age is found, continue to pressure wash ing.
CAUTION - Never use:
• Bleach, chlorine and other corrosive chem i cals
• Liquids containing solvents (i.e., paint thinners,
gas o line, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam age the surface being cleaned.
RINSING
It will take a few sec onds for the de ter gent to clear.
Apply safe ty latch to spray gun. Re move black soap
noz zle from the quick cou pler. Select and in stall the
de sired high pres sure noz zle. NOTE: You can also stop
de ter gent from flow ing by sim ply re mov ing de ter gent
si phon tube from bottle.
SHUTTING DOWN AND CLEAN-UP
STEP 1: Re move detergent suc tion
tube from container and insert into
1 gallon of fresh water. Turn vari able
pressure wand handle for low pres sure or connect the black de ter gent
noz zle. Pull trig ger on spray gun and
si phon water for one minute.
On-Off
Switch
STEP 2: Turn off the engine. STEP 3: Turn off water
supply.
PRESSURE WASHER
OPERATOR’S MAN U AL
Water
Inlet
STEP 4: Press
trig ger to re lease
wa ter pres sure.
STEP 5: Disconnect the gar den hose from the water inlet
on the machine.
STEP 6: Disconnect the high
pres sure hose from high pres sure out let.
STORAGE
CAUTION: Al ways store your pressure washer in a
lo ca tion where the temperature will not fall be low
32°F (0°C). The pump in this machine is sus cep ti ble
to permanent dam age if fro zen. FREEZE DAM AGE
IS NOT COV ERED BY WAR RAN TY.
1. Stop the pressure washer, squeeze spray gun trig ger to release pressure.
2. Detach water supply hose and high pressure
hose.
3. Turn on the machine for a few seconds, until re main ing water exits. Turn engine off im me di ate ly.
4. Drain the gas and oil from the engine.
5. Do not allow high pressure hose to become
kinked.
6. Store the machine and accessories in a room which
does not reach freezing temperatures.
CAUTION: Fail ure to follow the above di rec tions will
result in dam age to your pres sure washer.
When the pres sure washer is not being operated or is
be ing stored for more than one month, follow these
in struc tions:
1. Replenish engine oil to up per level.
2. Drain gas o line from fuel tank, fuel line, fuel valve
and carburetor.
3. Pour about one teaspoon of engine oil through
the spark plug hole, pull the starter grip several
9.801-192.0 • Rev. 02/11
High Pressure
Outlet
Safety
Latch
STEP 7: En gage the
spray gun safe ty lock.
times and re place the plug. Then pull the starter
grip slow ly until you feel increased pres sure which
indicates the pis ton is on its com pres sion stroke and
leave it in that position. This closes both the intake
and ex haust valves to prevent rusting of cylinder.
4. Cover the pressure washer and store in a clean, dry
place that is well ventilated away from open fl ame
or sparks. NOTE: The use of a fuel additive, such
as STA-BIL
®
, or an equivalent, will minimize the
for mu la tion of fuel deposits during shortage. Such
ad di tives may be added to the gasoline in the fuel
tank of the engine, or to the gasolinee in a storage
con tain er.
After Extended Storage
CAUTION: Prior to restarting, thaw out any
pos si ble ice from pressure washer hos es,
spray gun or wand.
Engine Maintenance
During the winter months, rare atmosheric conditions
may develop which will cause an icing con di tion in the
car bu re tor. If this de vel ops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
en gine over the carburetor area. NOTE: Refer to the
en gine man u fac tur er's manual for service and main te nance of the engine.
11
MAINTENANCE
PREVENTATIVE MAINTENANCE
1. Check to see that the water pump is properly lu bri cat ed.
2. Follow Winterizing Procedures to prevent freeze
dam age to the pump and coils.
3. Always neutralize and fl ush detergent from system
af ter use.
PRESSURE WASHER
4. If water is known to be high in mineral content, use
a water softener in your water system or de-scale
as needed.
5. Do not allow acidic, caus tic or abrasive fl uids to be
pumped through system.
6. Always use our high grade quality cleaning prod ucts.
OPERATOR’S MANUAL
7. Never run pump dry for extended periods of time.
8. Use clean fuel: kerosene, No. 1 fuel oil or diesel.
Re place fuel fi lter every 100 hours of operation.
Avoid water contaminated fuel as it will seize up
the fuel pump.
9. If machine is operated with smoking or eye burning
ex haust, coils will soot up, not letting water reach
max i mum operating temperature. (See section on
Air Adjustments.)
10. Never allow water to be sprayed on or near engine
or burner assembly or any electrical com po nent.
11. Periodically delime coils as per instructions.
12. Check to see that engine is properly lubricated.
It is advisable, periodically, to visually inspect the
burn er. Check air inlet to make sure it is not clogged or
blocked. Wipe off any oil spills and keep this equipment
clean and dry.
The areas around the pressure washer should be kept
clean and free of combustible materials, gasoline and
other flam ma ble vapors and liquids.
The flow of combustion and ventilating air to the burner
must not be blocked or obstructed in any manner. Con sult factory if vent stacking is going to be used.
MAINTENANCE AND SERVICE
Unloader Valves:
Unloader valves are preset and tested at the fac to ry
be fore shipping. Oc ca sion al adjustment of the unloader
may be nec es sary to main tain correct pressure. Call
your lo cal dealer for assistance.
Winterizing Procedure:
Damage due to freezing is not covered by warranty. Ad here to the following cold weather pro ce dures when ev er
the wash er must be stored or operated out doors under
freez ing conditions.
12
9.801-192.0 • Rev. 02/11
During winter months, when tem per a tures drop below
32°F, protecting your machine against freezing is nec es sary. Store the machine in a heated room. If this is not
pos si ble then mix a 50/50 solution of anti-freeze/water
into a 5 gal lon buck et. Place a short section of garden
hose into the buck et and connect it to the ma chine.
El e vate the buck et and turn the pump on to si phon the
anti-freeze through the ma chine. If com pressed air is
available, an air fitting can be screwed into the inlet
con nec tor and, by injecting com pressed air, all water
will be blown out of the system.
High Limit Hot Water Thermostat:
For safety, each machine is equipped with a high limit
con trol switch. In the event that the temperature of the
water should exceed its operating temperature, the
high limit con trol will turn the burner off until the water
cools.
Pumps:
Use only SAE 30W non-detergent oil. Change oil after
the first 50 hours of use. Thereafter, change the oil ev ery
three months or at 500 hour intervals. Oil level should be
checked by using the dipstick found on top of the pump
or the red dot visible through the oil gauge win dow. Oil
should be maintained at that level.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate
rap id ly inside the coil pipes. This growth is increased by
the extreme heat build up in the coil. The best pre ven tion
for liming conditions is to use high quality cleaning de ter gents. In areas where alkaline water is an extreme
prob lem, pe ri od ic use of our Deliming Powder (part
#9-028008) will remove lime and other deposits before
coil becomes plugged. (See Deliming Instructions for
use of Deliming Powder.)
Deliming Coils:
Periodic flushing of coils is recommended.
1. Fill a container or optional fl oat tank with 4 gallons
of wa ter, then add 1 lb. of deliming powder. Mix
thor ough ly.
2. Remove wand assembly from spray gun and put
spray gun into container. Secure the trigger on the
spray gun into the open position.
3. Attach a short section (3-5 ft.) of garden hose to
ma chine to siphon solution from an elevated con tain er. Turn pump switch on, allowing solution to
be pumped through coils back into the container.
So lu tion should be al lowed to circulate 2-4 hours.
4. After circulating solution fl ush entire system with
fresh water. Reinstall wand assembly to spray
gun.
Loading...