|
DUAL INPUT |
EZ1580/EZ1581 |
|
LOW DROPOUT REGULATOR |
EZ1582/EZ1583 |
February 26, 1999 |
TEL:805-498-2111 FAX:805-498-3804 WEB:http://www.semtech.com |
DESCRIPTION
The EZ158X family of high performance positive voltage regulators are designed for use in applications requiring very low dropout voltage at 7, 5, 3 and 1.5 amps. When supplying 2.5V on motherboards where both 5V and 3.3V supplies are available, the superior dropout characteristics of the EZ158X result in reduced heat dissipation compared to regular LDOs, thus allowing heat sink size reduction. Additionally, the EZ158X provides excellent regulation over variations in line, load and temperature. Remote sense operation allows compensating for trace, connector and other resistive losses.
Outstanding features include very low dropout performance at rated current, fast transient response, remote sense, internal current limiting, thermal shutdown and safe operating area protection of the output device. The EZ158X is a five terminal adjustable voltage regulator available in the popular 5 pin TO-220 and TO-263 plastic packages.
ORDERING INFORMATION
DEVICE |
PACKAGE |
IOUT (A) |
VOUT (V) |
EZ1580CT-X.X |
TO-220, |
7 |
See Note (1) |
|
|
|
|
EZ1581CT-X.X |
5-pin |
5 |
|
|
|
|
|
EZ1582CT-X.X |
|
3 |
|
|
|
|
|
EZ1583CT-X.X |
|
1.5 |
|
|
|
|
|
EZ1580CM-X.X |
TO-263, |
7 |
See Note (1) |
|
5-pin(2) |
|
|
EZ1581CM-X.X |
5 |
|
|
EZ1582CM-X.X |
|
3 |
|
|
|
|
|
EZ1583CM-X.X |
|
1.5 |
|
|
|
|
|
Notes:
(1)Where -X.X denotes voltage options. Available voltages are: 1.5V and 2.5V. Leave blank for adjustable version (1.3 to 5.7V).
(2)Add suffix ‘TR’ for tape and reel (TO-263).
FEATURES
•540mV dropout @ 7A in dual supply mode (EZ1580)
•Remote sense operation
•Fast transient response
•0.5% initial accuracy
•5 Pin TO-220 and TO-263 packages
APPLICATIONS
•Microprocessor supplies
•Split plane microprocessor supplies
•Pentium® Processor P54C and P55C
•PowerPC™ 603/604EV
•AMD5K86™, AMD K6
BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Parameter |
Symbol |
Maximum |
Units |
|
|
|
|
Input Voltage |
VP |
7 |
V |
VPOWER |
|||
VCONTROL |
VC |
13.2 |
|
Power |
PD |
Internally |
W |
Dissipation |
|
Limited |
|
Thermal Resistance |
|
|
|
Junction to Case |
|
2 |
|
EZ1580/1 TO-220 |
θ JC |
°C/W |
|
EZ1580/1 TO-263 |
|
2 |
|
EZ1582/3 TO-220 |
|
3 |
|
EZ1582/3 TO-263 |
|
3 |
|
Thermal Resistance |
|
|
|
Junction to Ambient |
|
50 |
°C/W |
EZ158X TO-220 |
θ JA |
||
EZ158X TO-263 |
|
60 |
|
Operating Junction |
TJ |
0 to 125 |
°C |
Temperature Range |
|
|
|
Storage Temperature |
|
|
|
Range |
TSTG |
-65 to 125 |
°C |
Lead Temperature |
TLEAD |
260 |
°C |
(Soldering) 10 Sec. |
|
|
|
Pentium is a registered trademark of Intel Corporation.
PowerPC is a trademark of IBM.
AMD5K86 and K6 are trademarks of Advanced Micro Devices. 1
© 1999 SEMTECH CORP. |
652 MITCHELL ROAD NEWBURY PARK CA 91320 |
|
|
|
|
DUAL INPUT |
EZ1580/EZ1581 |
|
|
|
|
||
|
|
|
|
||
|
|
|
|
LOW DROPOUT REGULATOR |
EZ1582/EZ1583 |
|
|
|
|
|
|
February 26, 1999
PIN CONFIGURATION
PIN DESCRIPTION
Pin |
Pin Name |
Pin Function |
|
|
|
1 |
SENSE |
This pin is the positive side of the reference voltage for this device. With this pin it is possible to |
|
|
Kelvin sense the output voltage at the load. |
2 |
ADJUST / |
This pin is the negative side of the reference voltage for the device. Transient response can be |
|
|
improved by adding a small bypass capacitor from the adjust pin to ground. |
|
GROUND |
This pin is the bottom end of the internal resistor feedback chain for fixed output voltage parts, |
|
|
and should be connected to ground. |
|
|
|
3 |
OUTPUT |
This is the power output of the device, and is electrically connected to the TAB. |
|
|
|
4 |
CONTROL |
This pin is the supply pin for the control circuitry for the device. The current flow into this pin will |
|
|
be approximately 1% of the output current. For the device to regulate, the voltage at this pin must |
|
|
be between 1.0V and 1.3V greater than the output voltage (see dropout specifications). |
5 |
POWER |
This is the collector input to the power device of the EZ158X. The output load current is supplied |
|
|
through this pin. For the device to regulate, the voltage on this pin must be between 0.1V and |
|
|
0.7V greater than the output voltage, depending upon load current (see dropout specifications). |
2
© 1999 SEMTECH CORP. |
652 MITCHELL ROAD NEWBURY PARK CA 91320 |