8KG
TOP LOAD
WASHING MACHINE
SC-8000AU7TL
INSTRUCTION
MANUAL
Please read this manual carefully before using, and keep it for future reference.
CONTENTS
General Safety 4
Product Overview 8
Getting Started 10
Levelling the appliance 11
Connecting the water inlet hose 12
Connecting the Drain Hose 13
Instructions 14
Operations 17
Cleaning and Maintenance 18
FAQs 21
Specifications 22
Customer Helpline 24
GENERAL SAFETY
IMPORTANT INFORMATION
Read this manual thoroughly before you start using the Top Load Washing
Machine. The safety precautions instructions reduces the risk of fire, electric
shock and injury when correctly complied to.
Please follow all instructions and take notice of all warnings.
Pay close attention to messages that follow this safety alert symbol or the words DANGER,
WARNING or CAUTION. These words will be used to alert you of potential hazards that and
injure you and others. Following these instruction will tell you how to reduce the chance of
injury and the possible dangers if instructions aren’t followed.
WARNING
CAUTION
This symbol indicates when there is a serious risk of injury if
you do not pay attention to the warnings.
This symbol indicates when to be careful to
avoid a serious risk of injury to oneself or
damage to property.
4
GENERAL SAFETY INSTRUCTIONS (Cont.)
ELECTRICAL SAFETY
• Voltage: Plug the appliance to a 240V ~ 50Hz, properly earthed power outlet, it
must be in good working order.
• Power connection: Do not use an adaptor or an extension cord. Plug the power
plug directly into a separate power point that cannot be accidentally turned o, and that
is easily accessible so you can switch it o if needed.
• Power cord: Do not kink or damage the power supply cord. Make sure it is behind
the appliance so no one can step on or place anything on the power supply cord or
against it. A damaged power plug may overheat and cause a fire.
• Damaged cord: Do not use a cord that shows cracks or damage. Any damage to the
cord may cause a short circuit, fire and/or electric shock. Contact our support centre
on 1300 296 699 for advice
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard
• Disconnection: Never pull the power cord to unplug appliance. Grip the plug and
pull straight out from the power point.
• Electrical work: If the installation of this appliance requires any electrical work,
make sure it is carried out by an electrician.
To reduce risk of fire, electric shock or injury, always follow these basic precautions and
accident prevention measures when using this appliance, including the below:
NOTE: This appliance should be installed by an authorised technician else warranty
will be void.
INSTALLATION
• The product is heavy, be careful when moving it. To avoid back or other injury, have 2
people lift or mechanical aid when installing.
• When unboxing, thoroughly inspect the appliance carefully for any damage. If there
is any damage, do not install the appliance. Contact our support centre on
1300 296 699 for advice.
• While installing the appliance make sure that the power cord is not bent or flattened.
• Make sure to remove all packaging materials such as foams and tapes before
installing the appliance.
• Make sure if the machine is to be placed on carpet that the ventilation openings in
the base are not obstructed
• Install the washing machine on a flat level and stable ground.
• Allow for 20mm of space on all sides of the washing machine.
• The openings shall not obstructed by carpet.
• This appliance is intended to be used in household and similar applications such as
- Sta kitchen areas in shops, oces and other working environments;
- Farm houses
- By clients in hotels, motels and other residential type environments;
- Bed and breakfast type environments;
- Areas for communal use in blocks of flats or in launderettes.
5
GENERAL SAFETY INSTRUCTIONS (Cont.)
USAGE CONDITIONS AND RESTRICTIONS
• Supervision over children is to ensure that they do not play with the appliance.
Never allow them to use, play with or crawl inside the appliance. Cleaning and
maintenance must not be done by children.
• This appliance is not to be used by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they are being supervised or been given instructions on how to use of the appliance in a
safe way and understand the hazards with using this appliance incorrectly.
• Only for indoor domestic use only. It is not to be used for industrial or commercial use.
• Do not use this product for anything other than its intended purpose, and only
use it as described in this manual. Do not attempt to alter or modify this appliance.
• In the process of a hot wash, the door window can become hot. Make sure not to
touch it or that no children or pets come into contact with the door window.
• Ensure that emptying all pockets of every item to make sure that there is no
hard, sharp objects such as coins, safety pins, bra wires, nails or screws can cause
damage to the appliance and has a chance to block the pump.
• Damage or malfunction caused from foreign objects is not covered by your
warranty to the appliance.
• Do not operate this appliance outdoors.
• Incorrect use can result in property damage, injury or death. We assume no
liability for misuse of the appliance or noncompliance with these instructions.
6
GENERAL SAFETY INSTRUCTIONS (Cont.)
CLEANING AND MAINTENANCE
• Before cleaning or maintenance, always unplug the appliance from the power socket.
Make sure you pull by the plug, not the cord as this can damage the power cord and
cause a hazard.
• Only the filter requires regular cleaning, everything else is non user-serviceable
parts. Do not try to repair, disassemble or modify the appliance.
• Check and clean the lint filter on a regular basis
• Service: Never try to repair, modify or replace any part of the appliance, unless this
manual says you can do so. All other servicing is to be done by a qualified technician,
or contact our support centre on 1300 296 699 for advice.
7
PRODUCT OVERVIEW
8
PRODUCT OVERVIEW (Cont.)
CONTROL PANEL
1 2 3 4 5 6 7
1. FUNCTION: This will show the types of spins in process according to the cycle thats
in progress.
2. WATER LEVEL: Before washing, you can select the water level according to how dirty
the items are, materials or the weight.
3. DELAY: Press and hold the “DELAY” button and every 0.5secs it will increase by
an hour at a time, let go to reach your desired hour for your wash to start
its cycle. If you go to 24hours, it will beep once then return back to 0.
4. PROGRAM: Before starting the washing machine, continously press the
“PROGRAM” button to select your desired program.
(REFER TO PAGE 17 FOR PROGRAMS
5. TEMP: Press the button to select the water temperature.
6. START/PAUSE: Press this button to start or pause the washing cycle.
7. ON/OFF: ON/OFF button allows you to turn the appliance off or on.
CHILD LOCK: When you commence a washing cycle,
Press and hold - (1) FUNCTION and (2) WATER LEVEL to lock the
washing machine control panel. Press and hold the same buttons
to unlock.
9
GETTING STARTED
Before installing your appliance, read all safety instructions in this manual,
especially the sections on electrical safety and installation.
UNPACKING
• When unpacking the appliance, be sure to keep all the packaging materials until
you have made sure your new appliance is undamaged and in good working
order. Plastic can be a suffocation hazard for babies and young children,
make sure the materials are out of their reach.
TRANSPORTATION
• CAUTION: VERY HEAVY! Be sure to team lift the appliance with someone or
mechanical aid is required when moving the appliance. Keep the appliance
upright as possible when moving the appliance.
IMPORTANT! Installing the bottom cover
• Make sure the power cord is unplugged from the
mains supply.
• Place some padding (such as a soft mat, blanket or
thick towel) on the floor and gently lay the washing
machine on the padding, back side down. Take care
not to dent the housing.
• Insert the bottom cover into the hooks of the leg,
pushing it straight until it reaches into the
front hooks.
• Ensure to fasten the bottom cover with the
supplied screws.
• Carefully set the washer upright.
10
GETTING STARTED (Cont.)
LEVELLING THE APPLIANCE
IMPORTANT! Make sure to level the appliance carefully with a spirit level to ensure the
most accurate levelling of the appliance. This is a must if your floor in unbalanced to level
the washing machine.
• Make sure to position the appliance on a level and stable ground. If the floor is uneven
you can adjust the feet by twisting the feet. Make sure to slightly incline the appliance first
then adjust the leveling feet by twisting it clockwise or counter clockwise depending if you
are raising or lowering the feet.
• By placing a spirit level ontop of the appliance you can check correctly to aid you in
adjusting the feet levelling nuts to adjust the appliance to be completely level.
Note: Make sure to avoid direct sunlight onto the appliance.
11
GETTING STARTED (Cont.)
CONNECTING THE WATER INLET HOSE
IMPORTANT! To prevent leakage or water damage please follow the below
instructions. Do not kink, crush, modify or sever the water inlet hose.
• Connect the inlet pipe as indicated, there are two ways of connecting
the inlet pipe.
• Minimum Inlet Water Pressure: 0.03MPa
Maximum Inlet Water Pressure: 0.8MPa
Connect the other end of the inlet
pipe to the inlet valve on the back
of the appliance and fasten the
pipe tightly clockwise.
12
GETTING STARTED (Cont.)
CONNECTING THE DRAIN HOSE
• Do not kink or protract the drain hose. Position the drain hose correctly other
wise damage will result in water leakage.
• The height of the water drain hose can be from 86 to 100cm.
• Do not bend the drain hose or place it under the washing machine.
• Be sure to only use new hose sets when connecting the Washing Machine.
Do not re-use old hoses.
13
INSTRUCTIONS
BEFORE FIRST USE
• Make sure the washing machine is completely level as to previous instructions
on how to level your washing machine.
• Make sure the water inlet hose is installed correctly.
• Make sure that the washing machine is plugged into the power socket.
• When the water inlet hose is installed, turn on the water supply on the tap.
• Properly install and set up the upper drain hose at no less then the
height of 860mm, the water will overflow if it is below the recommended
height of 860mm.
After the above steps have been completed, In a few simple steps you can select the type of
wash you want and get started.
14
INSTRUCTIONS (Cont.)
• Make sure that the appliance is in a correct working temperature (0-40˚C). If the
appliance is used under 0˚C the inlet valve and draining system may be damaged.
• Make sure that all labels are checked on items if they can be washed.
• Use non-foaming or less-foaming detergents which are more suitable for washing machines
to wash correctly.
WARNING
• Never use the washing machine to wash a single item at any given time, if you need to
urgently wash an item, we suggest placing a few clothing items in there.
• Make sure that all labels are checked on items if they can be washed.
• Use non-foaming or less-foaming detergents which are more suitable for washing machines
to wash correctly.
• Maximum mass of dry clothes is 8kg
15
INSTRUCTIONS (Cont.)
WASH CARE SYMBOLS
When choosing a wash program, check for any labels on your clothes and follow
the instructions. below are some commonly used symbols.
16
OPERATIONS
PROGRAMS
Select the desired programs according to the clothes that are being washed.
PROGRAMS
Normal Normal fabric washing program suitable to wash
Quick Suitable to wash lightly stained clothes.
cotton fabrics.
Anti-Wrinkle The wash time is short and rinses clothes many times
Heavy Suitable for washing large load size such as curtains
Jeans Suitable for washing heavy stained clothes and jeans.
Air Dry Air dry your clothes with just air, remove particular
*Normal- is the normal washing programs to which the information in the energy
efficiency label relates, and they are suitable to clean normal soiled cotton laundry and
they are the most efficient programs in terms of energy and water consumption for
washing that type of cotton laundry, the actual water temperature may differ from the
declared cycle temperature.
with high water levels to thoroughly wash the clothes.
and bed sheets. There additional 15 mins of soaking
time during wash process.
smells and air your clothes.
17
CLEANING AND MAINTENANCE
WARNING:
• Before starting maintenance, ensure that the appliance is unplugged and close the tap.
CLEANING THE CABINET
Proper maintenance on the washing machine can extend its working life. The surface can
be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any
water overflow, use a wet cloth to wipe it off immediately. Make sure no sharp items are
used to clean the appliance.
• Use a gentle cloth to wipe off the water and dirt on the surface of the washing machine
after every use. Detergent, properllant and other chmicals are not allowed to be used to
clean the washing machine surface as it can damage the plastic accessories.
CLEANING THE WATER INLET
1 Switch on the power, followed by shutting off the tap
2 Let the washer work for 5 seconds so that the water flows into the tub through the
hose, then turn off the power.
3 Unload the water inlet hose and clean the mesh bag, then re-install everything.
18
CLEANING AND MAINTENANCE (Cont.)
CLEANING THE INLET FILTER
1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long noise pliers and reinstall it back after being washed.
3. Use the brush to clean the filter.
4. Reconnect the inlet pipe.
CLEANING LINT FILTER
1. There is a built-in Lint filter in your washing machine. It can help to collect
lint during a washing cycle.
2. It is suggested to clean the lint filter every 10 cycles.
3. Take out and clean the filter with water. Then place it back into the washer.
19
CLEANING AND MAINTENANCE (Cont.)
CLEANING THE DRAIN PUMP FILTER
1 Drain the water out of the pump
under which you use a container to
collect the water.
3 Take out the lint filter.
2 Loosen the pump cover.
(anti-clockwise)
4 Clean the filter.
5 Restore it and adjust the
convex place to align at the
pump hole.
20
6 Tighten the pump cover
(clockwise)
FAQs
Please be sure to contact our call centre on 1300 296 699 if you cannot identify
the issue with the below information.
Problem Solution
• Check to see if the power is on
• The water supply is cut off or the water
pressure is too low.
• The inlet hose is properly connected and the
No water is flowing in
No washing
Abnormal draining
Abnormal Spin
water tap is opened.
• The filtering screen of inlet valve is blocked by dirt.
• The coil of the inlet valve is damaged.
• Make sure the Start/Pause button hasnt
been pressed.
• If the power is off or fuse has burned out
• The power supply voltage is too low
• The water amount reaches to the requiredwater
level. (The washer will not work if the water
amount does not reach the required water level)
• If it is set on “delay” then the washer will not
start until time is reached.
• The water drain hose is placed to high.
• The internal rubber ring of drain valve is blocked.
• Make sure the door lid is closed.
• If all clothing piled largely at one side of the barrel.
• The appliance must be placed completely level for
it to work correctly.
NOTE: During the de spin process of a washing cycle. If the washing is piled at one side
it will cause an unbalance of the barrel. The washing machine computer will feel this
unbalance and will automatically try to correct it, if its unable to correct in in three tries,
then you will have to manually open, pause the cycle and evenly place the clothing inside
the barrel to solve the problem.
21
SPECIFICATIONS
Power Supply 240V~50Hz
Standard Water Pressure 0.03MPa~0.8MPa
Washing Capacity 8KG
Rated Input Power 560W
Dimensions 580(w) x 605(d) x 980 (h) mm - (1200mm door open)
Weight Net: 42 kg / Gross: 47 kg
22
23
24
CUSTOMER HELPLINE:
1300 296 699
DISTRIBUTED BY:
Ayonz Pty Ltd
Loading...