SEH myUTN-2500 Quick guide

USB Deviceserver

myUTN-2500

Quick Installation Guide

MHAB-QI-myUTN2500
Version: 2.1 | 2018-11

Overview

This 'Quick Installation Guide' describes the hardware installation and initial
setup of the myUTN-2500.

Table of contents

1.

Do you need assistance? Contact us!

Monday to Thursday
Friday

8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)

[phone]

[e-mail]

www.seh-technology.com

Überblick

Dieser 'Quick Installation Guide' beschreibt die Hardware-Installation und
Inbetriebnahme des myUTN-2500.

Inhaltsverzeichnis

14.

Benötigen Sie Hilfe? Kontaktieren Sie uns!

Montag–Donnerstag
Freitag

8:00–16:45 Uhr
8:00–15:15Uhr

[phone]

[e-mail]

www.seh.de

 Contents

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Purpose .....................................................................................................................................2

Scope of Supply .....................................................................................................................2

Technical Data.........................................................................................................................3

LED Display ..............................................................................................................................4

Type Plate.................................................................................................................................4

Safety Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting the SEH UTN Manager ........................................................................................9

Assigning an IP Address to the UTN Server................................................................10

Adding the UTN Server to the Selection List.............................................................11

Connecting the USB Device to the Client...................................................................12

Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Regulatory Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

1 [en] Quick Installation Guide

 General Information

Purpose

The USB Deviceserver 'myUTN-2500' allows you to access non-network-ready
USB devices (e.g. hard disks, etc.) in the network. For this purpose, the USB
devices will be connected to the USB ports of the myUTN-2500. The software
tool 'SEH UTN Manager' handles the access to the USB devices.

The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network. The SEH UTN Manager shows the availability of all UTN
servers in the network and establishes a connection between the client and the
USB port including the connected USB device.

The administration of the myUTN-2500 is done via the 'myUTN Control Center'.

Scope of Supply

Check the package content before getting started:

UTN server USB Deviceserver 'myUTN-2500'

Quick
Installation
Guide

Power pack External power pack

The Quick Installation Guide provides a brief
description of the installation of the myUTN-

2500.
(This document)

Quick Installation Guide [en] 2

Technical Data

Link LED

(green)

Activity LED

(yellow)

USB ports 1–3

(port 3 = port for charging, 1.5 A)

LED for the USB ports 1–3

(green/orange)

Power LED

(yellow)

Status LED

(green)

Connector for the

included power pack

Reset buttonNetwork connector (RJ-45)

Properties Values

Network connector

logical:

physical:
Device connection 3 × USB 3.0 SuperSpeed
Current input • 200 mA at 12VDC without load

IEEE 802.3 (1000BaseT, 100BaseTX, and 10BaseT)
1 × RJ-45 (STP, category 5 or better)

• 2400 mA at 12VDC
with full load on the USB ports

Power consumption • approx. 2.9 W without load

• approx. 30 W with full load on the USB ports

• approx. 26 kWh/year

Operating Environment Ambient temperature: 5–40 °C

Relative humidity: 20–80 %

Dimensions Width: 140 mm

Height 32 mm
Depth: 99 mm
Weight: 160 g

3 [en] Quick Installation Guide

LED Display

The LEDs of the UTN server provide information about its status.

LED Action Color Description

Link permanently on

green–There is a connection to the network.

permanently off

Activity blinks at

irregular
intervals

Status permanently off

blinks 3 times

blinks 2 times

Power permanently on

permanently off

USB ports

permanently off

1–3

permanently on

There is no connection to the
network.

yellow Indicates the exchange of network

data packets.

–

If the activity LED blinks periodically
at the same time, the BIOS mode is
signalized.

green

Indicates the assignment of a
Zeroconf IP address.

green

Indicates the assignment of an IP
address that does not correspond to

0.0.0.0 or that comes from outside
the Zeroconf range.

yellow–The device is powered.

The device is not powered.

–

No USB device is connected to the
respective port.

green

A USB device is connected to the
respective port.

permanently on

orange

The connection to the respective
port and the attached USB device is
activated.

Important:

During the activation procedure, the behavior of the
LEDs differs from this description.

Type Plate

The type plate gives important product information, such as hardware and
certification information as well as the serial number. The serial number
contains the production date: nnn YYYY MM nnnnn.

This information helps you e.g. during maintenance and you need it for support
requests as well as for the guarantee extension.

Quick Installation Guide [en] 4

 Safety Regulations

UTN servers are network devices for use in office environments. The myUTN­2500 is designed for the integration of USB devices into TCP/IP networks.

Important:

Before starting the installation and the initial setup
procedure as well during the operation of the UTN
server, note the following safety regulations. Their
purpose is to protect yourself and others from personal
injuries, and to avoid damage to the equipment.

• Read the documentation and make sure that your system meets the require­ments listed therein.

• Avoid contact with humidity or liquids.

• The device must only be connected and operated if it is in perfect condition.

• Make sure that no-one steps on or stumbles over the cables.

• If the supplied power cord cannot be used in your country, acquire an appro­priate power cord that suits national provisions. For more information, con­sult your retailer.

• Do not connect a telephone cable to the RJ-45 connector. The RJ-45 connec­tor may only be connected to SELV voltages. For the connection to the RJ-45
connector only STP cabling (category 5 or better) may be used. The shielding
must fit flushly to the connector.

• Do not open the housing. Unauthorized modifications to the device can af­fect the product certification and are forbidden.

• The device must not be directly connected to outdoor lines.

• The device must only be operated using the power pack included in the
package.

• Only use a certified USB cable (< 3 m) listed at www.usb.org

• Electrostatic discharges (ESD) may impair device performance.

• An interruption of the supply voltage may impair device performance or
cause malfunctions.

.

5 [en] Quick Installation Guide

 Hardware Installation

USB devices

myUTN-2500

network

clients with software tool
'SEH UTN Manager'

USB 3.0

USB 3.0

USB 3.0

You can directly connect three USB devices to the myUTN-2500.

1. Connect the USB device to a USB port of the UTN server.

Important:

USB device and UTN server can be connected via a USB
cable, if required.
Only use USB cables shorter than 3 meters.

2. Repeat step 1 if you want to connect more than one USB device.)

3. Connect the network cable (RJ-45) to the UTN server.

4. Connect the power cord to the UTN server.
 The UTN server boots and then is ready for use.

Quick Installation Guide [en] 6

 Software Installation

The software tool 'SEH UTN Manager' organizes the access of the USB devices.
The SEH UTN Manager is available in two versions:

•Complete version

• Minimal version (only command-line interface)

The complete version has a graphical user interface and offers additional
features. A detailed description can be found in the myUTN User Manual.

The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network. Different installation files are available, depending on the
operating system.

First, you have to download the installation file for the SEH UTN Manager from
the website of SEH Computertechnik GmbH:

http://www.seh-technology.com/services/downloads/

download-deviceserver/myutn-2500.html

System requirements:
– Windows 7 or later except for Windows Server 20081;

OS X respectively macOS 10.9 or later

– The installation can only be carried out by users with administrative rights.

Important:

The SEH UTN Manager is also available for selected
Linux systems.
All information necessary for installing and using the
SEH UTN Manager in Linux environments can be found
in the myUTN User Manual Linux. The documentation is
available via the link given above.

1. Start the installation file.

2. Install the complete version of the SEH UTN Manager (including graphical

user interface). To do so, follow the installation routine.

 The SEH UTN Manager is installed on your client.

1. Windows 7 and Windows Server 2008 R2: KB3033929 (https://technet.microsoft.com/en-us/li-

brary/security/3033929) must be installed.

7 [en] Quick Installation Guide