Sega RACE TV User Manual

OWNER'S MANUAL

IMPORTANT

• Before using this product, read this manual carefully to understand the contents herein stated.

• After reading this manual, be sure to keep it near the product or in a convenient place for easy reference when necessary.

WARRANTIES

GAME WARRANTY POLICY

Your new SEGA PRODUCT is covered for a period of ninety (90) days from the date of the shipment. This certifies that all Printed Circuit boards, power supplies and monitors are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered. Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For warranty claims, contact your SEGA Distributor. Should the seller determine, by inspection that the problem was caused by accident, misuse, neglect, alteration, improper repair, installation or testing, the warranty offered will be null and void. Under no circumstances is the seller responsible for any loss of profits, loss of use, or other damages. This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstances shall it extend beyond the period of time listed above.

PARTS WARRANTY POLICY

Sega Amusements USA, Inc. warrants all parts to be free from defective materials and workmanship for a period of thirty (30) days from Sega Amusements USA, Inc. invoice date unless otherwise specified in writing by Sega Amusements USA, Inc.

This limited warranty is invalid for any part that upon examination, is deemed to have been subject to misuse, improper repair or installation, neglect or violation of specification or other instructions published by Sega Amusements USA, Inc. There are no additional warranties described above.

The limited warranties described above shall be in lieu of any other warranty, express or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.

BEFORE USING THE PRODUCT,

To maintain safety:

To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual close to the product or in a convenient place for future reference.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

BE SURE TO READ THE FOLLOWING:

Indicates that mishandling the product by disregarding this pictograph will cause severe injury or death.

Indicates that mishandling the product by disregarding this warning will cause a potentially hazardous situation which can result in death or serious injury.

For the safe usage of the product, the following pictographs are used:

Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this display is attached to places where the Owner's Manual, Serviceman Manual and/or Service Manual should be referred to.

Indicates a "Protective Earth Terminal." Before operating the equipment, be sure to connect it to the Ground. (The step may be omitted for products in which a power cord with earth is used.)

❍ Perform work in accordance with the instructions herein stated.

Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the site maintenance personnel should perform such work.

Indicates that mishandling the product by disregarding this caution will cause a slight hazardous situation which can result in personal injury and/or material damage.

❍ Be sure to turn off the power before working on the machine.

To prevent an electric shock, be sure to turn off the power before carrying out any work that requires direct contact with the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

❍ Be sure to ground the Earth Terminal.

(This is not required in the case where a power cord with earth is used.)

This product is equipped with the Earth Terminal. When installing the product, connect the Earth Terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the product is grounded appropriately, the user can be subject to an electric shock. After performing repair, etc. for the control equipment, ensure that the Earth Wire is firmly connected to the control equipment.

❍ Ensure that the Power Supply used is equipped with an Earth Leakage Breaker.

This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

❍ Be sure to use fuses which meet the specified rating.

(Only for the machines which use fuses.)

Using fuses exceeding the specified rating can cause a fire and an electric shock.

❍ Specification changes (removal of equipment, conversion and addition) not

designated by SEGA are not allowed.

The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and/or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA.

❍ Ensure that the product meets the requirements of appropriate Electrical

Specifications.

Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and an electric shock.

❍ Install and operate the product in places where appropriate lighting is

available, allowing warning labels to be clearly read.

To ensure safety for the customers, labels and printed instructions describing potentially hazardous situations are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated.

❍ When handling the monitor, be very careful.

(Applies only to the product with a monitor.)

Some of the monitor (TV) parts are subject to high tension voltage. Even after turning off the power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only by those technical personnel who have knowledge of electricity and technical expertise.

❍ Be sure to adjust the monitor/projector properly.

(Applies only to the product with a monitor/projector.)

Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor/projector not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers.

❍ When transporting or reselling this product, be sure to attach this manual to

the product.

In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

* Descriptions herein contained may be subject to improvement changes without notice. * The contents described herein are fully prepared with due care. However, should any

question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on the power, check the following points to ensure that the product has been transported in a satisfactory status.

❐ Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? ❐ Are Casters and Adjusters damaged? ❐ Do the power supply voltage and frequency requirements meet with those of the location? ❐ Are all wiring connectors correctly and securely connected? Unless connected in the correct

way, connector connections can not be made accurately. Do not insert connectors forcibly.

❐ Do power cords have cuts and dents? ❐ Do the fuses used meet specified ratings? Is the Circuit Protector in an energized status? ❐ Are all accessories available? ❐ Can all Doors and Lids be opened with the Accessory Keys? Can Doors and Lids be firmly

closed?

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:

TABLE OF CONTENTS .......................................................................................i

INTRODUCTION ................................................................................................iv

1 HANDLING PRECAUTIONS .........................................................................1

2 PRECAUTIONS REGARDING INSTALLATION LOCATION ........................5

2-1 LIMITATIONS OF USAGE ................................................................................................5

2-2 OPERATION AREA ..........................................................................................................6

3 PRECAUTIONS REGARDING PRODUCT OPERATION .............................7

4 PART DESCRIPTIONS ................................................................................11

5 ACCESSORIES ...........................................................................................12

6 ASSSEMBLY AND INSTALLATION ............................................................15

6-1 FIXATION TO INSTALLATION SITE ..............................................................................18

6-2 TURNING ON THE POWER (SOFTWARE INSTALLATION) ........................................17

6-3 CHECKING ASSEMBLY (SETUP) .................................................................................22

TABLE OF CONTENTS

7 PRECAUTIONS WHEN MOVING THE MACHINE ...........................................................................25

8 GAME DESCRIPTION ......................................................................................................................27

8-1 GAME OVERVIEW .........................................................................................................27

8-2 GAME FLOW ..................................................................................................................29

8-3 MODE OVERVIEW .........................................................................................................32

8-3-1 MULTI PLAYER GAME .........................................................................................32

8-3-2 SINGLE PLAYER GAME .......................................................................................32

8-4 PASSWORDS .................................................................................................................33

8-5 TIME RELEASE ..............................................................................................................34

9 TEST MODE ................................................................................................ 35

9-1 SWITCH UNIT AND COIN METER ................................................................................36

9-2 SYSTEM TEST MODE ...................................................................................................38

9-3 GAME TEST MODE .......................................................................................................39

9-3-1 GAME TEST MODE Menu ....................................................................................39

9-3-2 INPUT TEST ..........................................................................................................40

TABLE OF CONTENTS

9-3-3 OUTPUT TEST ......................................................................................................41

9-3-4 FORCE FEEDBACK .............................................................................................42

9-3-5 INPUT ASSIGNMENTS .........................................................................................43

9-3-6 GAME ASSIGNMENTS .........................................................................................47

9-3-7 BOOKKEEPING ....................................................................................................49

9-3-8 BACKUP DATA CLEAR ........................................................................................51

10 CONTROL PANEL (HANDLE MECHA) ......................................................52

10-1 REMOVING THE CONTROL PANEL ...........................................................................53

10-2 ADJUSTING/REPLACING THE VOLUME ...................................................................54

10-3 GREASING ...................................................................................................................56

11 SHIFT LEVER ..............................................................................................57

11-1 REMOVING THE SHIFT LEVER ..................................................................................57

11-2 SWITCH REPLACEMENT ............................................................................................58

12 ACCELERATOR & BRAKE .........................................................................59

12-1 VOLUME ADJUSTMENT AND REPLACEMENT ........................................................60

12-2 GREASING ...................................................................................................................62

13 MONITOR ..........................................................................................................................................63

13-1 CAUTIONS AND WARNINGS CONCERNING

THE SAFETY FOR HANDLING THE MONITORS ......................................................63

13-2 CLEANING THE CRT SURFACES ..............................................................................66

13-3 ADJUSTMENT PROCEDURE ......................................................................................67

14 FLUORESCENT LIGHT/OTHER LAMPS REPLACEMENT.............................................................69

15 PERIODIC INSPECTION ..................................................................................................................73

16 TROUBLESHOOTING ......................................................................................................................75

16-1 TROUBLESHOOTING (WHEN NO ERROR MESSAGE IS SHOWN) .........................75

16-2 ERROR MESSAGES ....................................................................................................79

17 GAME BOARD ..................................................................................................................................81

17-1 REMOVING THE LINDBERGH ....................................................................................81

17-2 COMPOSITION OF THE GAME BOARD .....................................................................83

18 COMMUNICATION PLAY ............................................................................84

18-1 INSTALLATION PRECAUTIONS .................................................................................84

18-2 CONNECTING THE COMMUNICATION CABLE ........................................................86

18-3 NETWORK PLAY SETTINGS ......................................................................................87

18-4 NETWORK PLAY PRECAUTIONS ..............................................................................88

19 DESIGN-RELATED PARTS .........................................................................89

20 PARTS LIST .................................................................................................90

21 WIRE COLOR CODE TABLE ....................................................................102

22 WIRING DIAGRAM ....................................................................................103

TABLE OF CONTENTS

iii

INTRODUCTION

This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product, “SEGA-RaceTV.”

This manual is intended for the owners, personnel and managers in charge of operation of the product.

INTRODUCTION

Operate the product after carefully reading and sufﬁ ciently understanding the instructions.

In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician to touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the outlet, and contact the ofﬁ ce listed below or the point of purchase for this product.

Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special attention are indicated by bold text, the word “IMPORTANT” and the symbol below.

Indicates important information that, if ignored, may result in the mishandling of the product and cause faulty operation or damage to the product.

Sega Amusements U.S.A., Inc.

800 Arthur Avenue, Elk Grove Village, IL 60007-5215, U.S.A.

TEL: 1-847-364-9787 TOLL FREE: 1-888-877-2669 FAX: 1-847-427-1065

SPECIFICATIONS

Dimensions: Unit : 36.5” [Width] x 69.1” [Depth] x 74.5” [Height]

Weight: Unit : 562.2 lbs.

Power, maximum current: 540 W, 4.5 A (AC 120 V, 60 Hz)

Monitor: 29 Type Color Monitor

NOTE: The contents herein described are subject to change without notice.

Deﬁ nition of 'Site Maintenance Personnel or Other Qualiﬁ ed Individuals'

Procedures not described in this manual or marked as 'to be carried out by site maintenance personnel or other qualiﬁ ed professionals' should not be carried out by personnel without the necessary skill or technology. Work carried out by unqualiﬁ ed persons may cause serious accidents, including electrocution.

Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel or other qualiﬁ ed professionals. This manual includes directions for potentially dangerous procedures which should only be carried out by professionals with the appropriate specialized knowledge.

The site maintenance personnel or other qualiﬁ ed professionals mentioned in this manual are deﬁ ned as follows:

Site maintenance personnel:

Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the supervision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/ expendable parts.

Activities to be carried out by site maintenance personnel:

Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable parts.

INTRODUCTION

Other qualiﬁ ed professionals:

Persons employed by amusement equipment manufacturers, or involved in design, production, testing or maintenance of amusement equipment. The individual should have either graduated from technical school or hold similar qualiﬁ cations in electrical/electronics/mechanical engineering.

Activities to be carried out by other qualiﬁ ed professionals:

Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.

HANDLING PRECAUTIONS

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

• Before performing work, be sure to turn the power off. Performing the work without turning the power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect.

• To avoid an electric shock or short circuit, do not plug in or unplug quickly.

• To avoid an electric shock, do not plug in or unplug with a wet hand.

• Do not expose power cords or earth wires on the surface, (ﬂ oor, passage, etc.). If exposed, the power cords and earth wires are susceptible to damage. Damaged cords and wires can cause an electric shock or short circuit.

• To avoid causing a ﬁ re or an electric shock, do not put things on or damage the power cords.

HANDLING PRECAUTIONS

• When or after installing the product, do not unnecessarily pull the power cord. If damaged, the power cord can cause a ﬁ re or an electric shock.

• In case the power cord is damaged, ask for a replacement through where the product was purchased from or the ofﬁ ce herein stated. Using the cord as is damaged can cause ﬁ re, an electric shock or leakage.

• Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock.

• Be sure to use fuses meeting the speciﬁ ed rating. Using fuses other than the speciﬁ ed rating can cause a ﬁ re or an electric shock.

• Be sure that connections such as IC BD are made properly. Insufﬁ cient insertion can cause an electric shock.

• Speciﬁ cation changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

- Failure to observe this may cause a ﬁ re or an electric shock. Non-compliance with this instruction can have a bad inﬂ uence upon physical conditions of the players or the onlookers, or result in injury during play.

- SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by speciﬁ cation changes not designated by SEGA.

• Do not perform any work or change parts not listed in this manual. Doing so may lead to an accident.

If you need to perform any work not listed in this manual, request work from the

ofﬁ ce indicated in this manual or the point of purchase, or inquires for details.

• Be sure to perform periodic maintenance inspections herein stated.

• For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard.

• When cleaning the CRT surfaces, use a soft and dry cloth. Do not apply

HANDLING PRECAUTIONS

chemicals such as thinner, benzene, etc.

• Static electricity from your body may damage some electronics devices on the IC board. Before handling the IC board, touch a grounded metallic surface so that the static electricity can be discharged.

• Some parts are not designed and manufactured speciﬁ cally for this game machine. The manufacturers may discontinue, or change the speciﬁ cations of such general-purpose parts. If this is the case, SEGA cannot repair or replace a failed game machine whether or not a warranty period has expired.

CONCERNING THE STICKER DISPLAY CONCERNING WARNING DISPLAYS

This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical Speciﬁ cations. It also has a Sticker describing where to contact for repair and for purchasing parts. When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker. The Serial Number indicates the product register. Identical machines could have different parts depending on the date of production. Also, improvements and modiﬁ cations might have been made after the publication of this manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.

This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing maintenance, be very careful of the warning displays. It is especially important that any complex repair and replacement work not mentioned herein should be performed by those technical personnel who have knowledge of electricity and technical expertise. In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.

HANDLING PRECAUTIONS

SEE A

PRECAUTIONS REGARDING INSTALLATION LOCATION

This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a ﬁ re, electric shock, injury and/or malfunction.

- Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and/or shower, etc.

- Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc.

- Places ﬁ lled with inﬂ ammable gas or vicinity of highly inﬂ ammable/volatile chemicals or hazardous matter.

- Dusty places.

- Sloped surfaces.

- Places subject to any type of violent impact.

- Vicinity of anti-disaster facilities such as ﬁ re exits and ﬁ re extinguishers.

- Areas where the temperature exceeds the applicable temperature (ambient temperature) range of 5 to 30 degrees centigrade.

PRECAUTIONS REGARDING INSTALLATION LOCATION

2-1 LIMITATIONS OF USAGE

• Be sure to check the Electrical Speciﬁ cations. Ensure that this product is compatible with the location's power supply, voltage, and frequency requirements. A plate describing Electrical Speciﬁ cations is attached to the product. Non-compliance with the Electrical Speciﬁ cations can cause a ﬁ re and electric shock.

• This product requires a breaker and earth mechanism as part of the location facilities. Using the product without these can cause a ﬁ re and electric shock.

• Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC single phase 100 V ~ 120 V area). Non-compliance with the Electrical Speciﬁ cations can cause a ﬁ re and electric shock.

• Be sure to use an independent power supply equipped with an earth leakage breaker. Using a power supply without an earth leakage breaker can cause an outbreak of ﬁ re if a power surge occurs.

• Putting many loads on one electrical outlet can cause generation of heat and a ﬁ re resulting from overload.

• When using an extension cord, ensure that the cord is rated at 15 A or higher (AC 100 V ~ 120 V area). Using a cord rated lower than the speciﬁ ed rating can cause a ﬁ re and electric shock.

PRECAUTIONS REGARDING INSTALLATION LOCATION

2-2 OPERATION AREA

• For safe operation, use and operate this product in an area measuring at least

1.67 m (65.7 in) in width and 2.3 m (90.6 in) in depth. The area prescribed in this manual is absolutely necessary, for if one should fall over and hit their head against something, there could be a serious accident.

• Be sure to provide sufﬁ cient space speciﬁ ed in this manual. Do not allow objects to block the ventilation ports. It can cause generation of heat and a ﬁ re.

• SEGA shall not be held responsible for damage or compensation for damage to a third party, resulting from the failure to observe this instruction.

• If the machine does not ﬁ t through the entryway to the installation location, do not disassemble it without ﬁ rst consulting the instructions. The machine should only be disassembled in accordance with the instructions listed in this manual; do not attempt to disassemble it in any other way. This may cause electric shock or short circuits.

To install this product, the entrance must be at least 1 m in width and 1.8 m in height.

PRECAUTIONS REGARDING PRODUCT OPERATION

To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.

BEFORE OPERATION

In order to avoid accidents, check the following before starting the operation:

• To ensure maximum safety for the players and the customers, ensure that where the product is operated has sufﬁ cient lighting to allow any warnings to be read. Operation under insufﬁ cient lighting can cause bodily contact with each other, hitting accident, and/or trouble between customers.

• Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's ﬂ ickering or deviation as is. Failure to observe this can have a bad inﬂ uence upon the players' or the customers' physical conditions.

• It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest.

• Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.

PRECAUTIONS REGARDING PRODUCT OPERATION

Ensure that all of the anti tip brackets are in contact with the floor.

3 FIG. 01

Ensure that all of the adjusters are in contact with the floor.

• Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage.

• Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step ladder.

PRECAUTIONS REGARDING PRODUCT OPERATION

• To avoid electric shock, check to see if door & cover parts are damaged or omitted.

• To avoid electric shock, short circuit and/or parts damage, do not put the following items on or in the periphery of the product. Flower vases, ﬂ owerpots, cups, water tanks, cosmetics, and receptacles/containers/vessels containing chemicals and water.

• During daily cleaning, be sure to check the surface of the steering wheel, gear shifter, and other parts that the player touches with his hands for damage, cracks, or loose screws. If a player uses the machine while it is damaged, cracked, or has a loose screw, the player may become injured.

• During daily cleaning, be sure to check the seat for any abnormality, wetness, etc. Failure to do this may result in deliberate tampering or negligence being left undetected.

• To avoid injury, be sure to provide sufﬁ cient space by considering the potentially crowded situation at the installation location. Insufﬁ cient installation space can cause making bodily contact with each other, hitting accidents, and/or trouble between customers.

DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

• For safety reasons, do not allow any of the following people to play the game.

- Those who need assistance such as the use of an apparatus when walking.

- Those who have high blood pressure or a heart problem.

- Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.

- Those who have neck or spinal cord problems.

- Those who are intoxicated or under the inﬂ uence of drugs.

- Pregnant women.

- Persons susceptible to motion sickness.

- Persons who disregard the product's warning displays.

• Even players who have never been adversely affected by light stimulus might experience dizziness or headache depending on their physical condition when playing the game. Small children are especially likely to experience these symptoms. Caution guardians of small children to keep watch on their children during play.

• Instruct those who feel sick during play to have a medical examination.

PRECAUTIONS REGARDING PRODUCT OPERATION

• To avoid injury from falls and electric shocks due to spilled drinks, instruct the player not to place heavy items or drinks on the product.

• To avoid electric shocks and short circuits, do not allow customers to put hands and ﬁ ngers or extraneous matter in the openings of the product or small openings in or around the doors.

• To avoid falls and resulting injury, immediately stop the customer from leaning against or climbing on the product, etc.

• To avoid electric shock and short circuit, do not allow customers to unplug the power plug without a justiﬁ able reason.

• This game is for one player only. If two or more customers attempt to sit in the seat and play at the same time, it may results in players falling over, falling off, or catching body parts in the ride.

• Persons other than the player should not be allowed to touch the controls during play. They may brush against or collide with the controls or the player, possibly resulting in accidents.

3 FIG. 02

PRECAUTIONS REGARDING PRODUCT OPERATION

• Customers should be warned not to place children on their laps while they play the game. Doing so may cause the child to become trapped between the player and the control panel and/or cause the machine to tip over.

3 FIG. 03

Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down.

PART DESCRIPTIONS

PARTS DESCRIPTIONS

4 FIG. 02 Rear View

Conﬁ rm that the accessories listed in the table below are present when setting up the product. Accessories marked “Spare” in the note column are consumable items but included as spares.

5 T ABLE 01

ACCESSORIES

OWNER’S MANUAL 542-30-300 (1) This manual

5 TABLE 02 SOFTWARE KIT XKT-1675-D -EX1 <USA>

DVD SOFTWARE KIT (1)

ACCESSORIES

ACCABLE(PowerCode)COMMUNICATIONCABLE5m 99-00-017(1)

KEY CHIP (1)

CUSION SPONGE 601-11137 (1)

Disc Protector

DVD-ROM DISC (1)

DISC CASE (1)

When you order the DVD-ROM disc only, specify the part number 610-0726-0044 (DVD SOFT RTV).

NOTE; The game software has been pre-installed in the main PCB and the key chip has been pre-set to the main PCB. Please use the DVD software, only when necessary for some reason such as replacing the main PCB. However to install the software, the DVD DRIVE and USB(mini type) cabele need to be prepared separately. Those are not included in the unit and available separately at SEGA.

ASSEMBLY AND INST ALLATION

• Perform assembly work by following the procedure herein stated. Failure to comply with the instructions can cause electric shock.

• Perform assembling as per this manual. Since this is a complex machine, incorrect assembling can cause an electric shock, machine damage and/or improper functioning as per speciﬁ ed performance.

• When assembling, more than one person is required. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage.

• Ensure that connectors are properly connected. Improper connections can cause electric shock.

• This work should be carried out by the site maintenance personnel or other qualiﬁ ed professionals. Work performed by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. If no one with proper technological expertise is available, request service from the ofﬁ ce indicated in this document or the point of purchase so as to ensure safety.

ASSEMBL Y AND INST ALLATION

• Provide sufﬁ cient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difﬁ cult.

• To perform work safely and avoid serious accident such as the cabinet falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

• Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a risk of ﬁ re.

• Do not leave power cords, ground wires, or network cables exposed in areas of heavy foot trafﬁ c. Doing so may cause them to become damaged, possibly resulting in electric shock and/or short circuits. When laying wiring across the ﬂ oor, always use safety covers to protect the wires.

• The power cord for this product has a ground terminal. Make sure to use this ground terminal when plugging it in to an indoor outlet. Failure to properly ground the product could lead to electrocution. It can also lead to malfunction.

ASSEMBL Y AND INST ALLATION

• When opening/closing, attaching/removing doors or lids, be careful that your hand or ﬁ nger does not get caught in anything.

• To perform the operation safely and accurately you must use a safe, steady footstool or stepladder. Working without this may lead to a fall and possible injury.

• Wear appropriate work clothing so that work can be performed safely. Use gloves and safety shoes to prevent accidents or injuries.

• When installing a wire protection cover over a ﬂ oor, use a material shaped so that no one passing by will stumble over it. Using a material that could be stumbled over might lead to an accidental fall.

• Handle plastic parts with care. Excessive weight or pressure may cause them to break and the broken pieces may cause injury.

When carrying out the assembling and installation, follow the following 6-item sequence.

6-1 Fixation to installation site

6-2 Turning on the power (Software Installation)

6-3 Checking assembly (Setup)

Tools necessary for work

24mm

Spannerwithmeasuringdistanceof24mmtooppositeside(forM16hexagonbolts)

6-1 FIXATION TO INSTALLATION SITE

Make sure that all the adjusters contact the ﬂ oor. Otherwise the cabinet could move, causing an accident.

This product has 4 casters and 4 adjusters.

Up to 4 machines can be connected for multi-player games. If several machines are to be installed, refer to Chapter

19.

Move the product to the installation site. See Chapter 19 for an example of installation. Make sure to leave

1 2

enough passage space for the player to get into the seat. Also leave some space on the back lid side for performing maintenance work later.

Have all the adjusters make contact with the ﬂ oor. Adjust the adjuster’s height by using a wrench so that the

machine position is kept level.

After making adjustment, fasten the adjuster nut upward and secure the height of adjuster.

ASSEMBL Y AND INST ALLATION

6-2 FIG. 02

ADJUSTER

CASTER

Tighten nut upwards.

About 5 mm

ADJUSTER

ASSEMBL Y AND INST ALLATION

Attach the anti tip brackets to the left and right sides. Remove the 2 hexagon bolts from each side. These

6-2 FIG. 03

will be used to fasten the anti tip brackets.

1,670 mm (65.7 in)

928 mm (36.5 in)

700 mm (27.6 in) over

Provide ventilation space for the ventilation opening. Allow more than 70 cm (approx. 28 in) of space for customer trafﬁ c.

150 mm (5.9 in)

VENTILATION SPACE 200 mm (7.9 in)

2,300 mm (90.6 in)

6-2 FIG. 05

6-2 TURNING ON THE POWER (SOFTWARE INSTALLATION)

The software installation is not necessary for this game, as it is pre-installed into the main PCB. Please refer to the following section, only when necessary.

• Be careful not to damage the DVD wire by getting it caught between objects, etc. Doing so may cause a short circuit or ﬁ re.

• The following explanation assumes that the product has been assembled properly as explained above. If there is an error or if the product operates in a manner other than as indicated below, cut off the power supply immediately. Failure to do so may result in a ﬁ re or electrical shock.

• If you look directly at the laser beam in the DVD DRIVE, you could suffer vision impairment. Do not look inside the DVD DRIVE.

• Do not use or store the DVD DRIVE or DVD wire in any of the following locations, as this may result in serious damage.

ASSEMBL Y AND INST ALLATION

[Do not use or store in these locations]

- Anywhere which may vibrate or shock the equipment

- In direct sunlight

- In damp or dusty places

- In places with a sharp change in temperature

- Close to anything that gives off heat (a heater, etc.)

- Close to anything with a strong magnetic ﬁ eld (magnets, monitor, speakers, radio, etc.)

- Anywhere that is likely to get wet (kitchen, etc.)

- Anywhere with a slope or incline

- Anywhere with corrosive gas in the air (chlorine, hydrogen sulﬁ de, ammonia, sulfur dioxide, etc.)

- Anywhere with strong static electricity

[Do not use in these locations]

- Close to anything that is highly retentive of heat (carpet, sponge, cardboard, etc.)

- Anywhere that blocks the DVD DRIVE air vent.

• The DVD DRIVE is a delicate piece of equipment. Avoid the following.

- Dropping or shaking it violently.

- Getting water or other liquids on it, or placing small items on top of it.

- Placing large or heavy items on top of it.

- Drinking or smoking close to the DVD DRIVE.

• Do not turn off the power to the DVD DRIVE when its access lamp is on or ﬂ ashing, as this could cause damage to the device.

ASSEMBL Y AND INST ALLATION

• Do not allow any foreign materials, such as liquids, metals or smoke inside the DVD DRIVE.

• Use a soft, dry cloth to wipe off any dirt or marks on the DVD DRIVE.

- If you need to use a cleaning agent, always use a “neutral” agent diluted in water.

- Never use products or cleaning agents containing benzene, alcohol, thinners, etc.

• Do not touch the lens inside the DVD DRIVE. Doing so may prevent it from reading accurately.

• The chip components on IC boards can be damaged by electrostatic discharge from the human body. Before handling an IC board, always neutralize any static charge in the body by touching a grounded metal surface.

• Some parts are not designed and manufactured speciﬁ cally for the kit. The manufacturers may discontinue, or change the speciﬁ cations of such general purpose parts. If this is the case, SEGA cannot repair or replace a failed kit whether or not a warranty period has expired.

Handling the DVD-ROM Disc

• Do not use a DVD-ROM with a damaged front. This may cause a malfunction.

• Insert the DVD-ROM into the DVD DRIVE with the label facing upwards.

• Do not get ﬁ ngerprints or dust particles on the disc. Contaminated discs may lower audio and video quality, and may result in read malfunctions.

ASSEMBL Y AND INST ALLATION

• When cleaning the disc, do not use volatile chemicals (benzene, thinner, etc.), cleaning sprays, or antistatic agents.

Wipe the disc with a soft cloth, working from the center outwards.

6-5 FIG. 01

• Do not use a cracked, warped, or damaged disc. Do not attach papers or seals onto the disc to avoid scratching it. Do not use a disc with signs of peeled seals, tape, etc. If such a disc is placed in the DVD-ROM DRIVE, malfunctions, such as the inability to remove the disc from the drive, may result.

• When cleaning a heavily contaminated disc, use a clean cloth that has been soaked in water and squeezed. After wiping, remove any remaining moisture with a clean, dry cloth.

• How to Hold a Disc

When handling a disc, be careful not to contaminate it with your ﬁ ngerprints.

With both hands:

Put your thumbs and forefingers on 4 opposite sides of the disc.

With one hand:

Insert your forefinger into the center hole, while placing your thumb and middle finger on opposite sides of the disc.

6-5 FIG. 02

6-5 FIG. 03

• The software is not installed on the game board (LINDBERGH) when the power supply is engaged, so the “Error 22” message is not a malfunction. However, if there is another error display, or if there is no video output at all, there might have been an error in product assembly, wiring connections might be faulty, or the LINDBERGH might not be functioning properly.

• After the power supply is engaged, wait for “Error 22” message to be displayed. If the product is indiscriminately operated in any way beforehand, there could be unexpected problems or malfunctions, as well as damage to parts.

• Once “Error 22” is displayed, set the DVD-ROM in the DVD DRIVE and re-engage the power supply. Installation takes place.

• After the power supply is engaged, the DVD DRIVE tray will not come out for about 30 seconds even if you press the switch. This is due to DVD DRIVE initialization.

ASSEMBL Y AND INST ALLATION

• The DVD DRIVE tray can come out or return only while the power supply is engaged. The tray cannot be opened or closed while the power is off.

• Even after the software has been installed, store the DVD software kit, DVD DRIVE and DVD wire in a secure location.

• If for any reason installation cannot be completed, an error is displayed. Refer to the LINDBERGH service manual and take corrective action.

Take out the DVD software kit provided.

Turn on the MAIN POWER switch on the AC unit.

The LINDBERGH startup image appears on the screen. However, it does take several minutes for the

2 3

projector image to become visible. Wait for at least one minute. An error will occur. Check to see if it is “Error 22.” If it is “Error 22,” proceed to the next operation. If it is not “Error 22,” take corrective measures as indicated in the LINDBERGH service manual.

Remove 1 urea (resin-head) screw, and then

remove DVD DRIVE case lid.

CASE LID

6-5 FIG. 04

Press the DVD DRIVE switch. The DVD DRIVE

tray comes out. Set the DVD from the DVD software kit into the tray. Always have the DVD label side facing upward.

6-5 FIG. 05

5 6 7 8

Press the DVD DRIVE switch and the tray returns to its original position.

Reset power. Turn the MAIN POWER switch to OFF, wait for at least 10 minutes, and then turn the switch

to ON. Wait until the projector lamp cools.

Software installs automatically from the DVD to the LINDBERGH. In some cases, it may take as long as

30 minutes for the software to install to the LINDBERGH.

After the software installation, the game image

appears automatically.

6-5 FIG. 06 ADVERTISE SCREEN

ASSEMBL Y AND INST ALLATION

Press the DVD DRIVE switch to have the tray come out, and then remove the DVD.

Press the DVD DRIVE switch to have the tray return. When the power is cut off the tray will not move.

Set the MAIN POWER switch to OFF.

Remove 2 DVD wires from the DVD DRIVE.

Refer to steps 1-13 in “6-3 ATTACHING DVD DRIVE AND KEY CHIP” and follow the steps in reverse

13 14

order to detach the DVD wire (2 m) from the cabinet.

Attach DVD DRIVE case lid and fasten it with 1 urea (resin-head) screw. Store DVD DRIVE and DVD software kit at a location where there is no dust or cigarette smoke.

Turn on the MAIN POWER switch on the AC unit. When the game image appears, installation is complete.

+ 84 hidden pages