Scotsman SW 12 USPH-S Service Manual

Pagina 1

Pagina 1

SCOTSMAN EUROPE - FRIMONT SPA
Via Puccini, 22 - 20010 Pogliano M.se - Milano - Italy
Tel. [phone] (Aut. Sel.)- Telefax [phone]
Direct Line to Service & Parts:
Phone [phone] - Fax [phone]
Website: www.scotsman-ice.com
E-Mail: [e-mail]

ISO 9001 - Cert. n. 0080

SERVICE MANUAL

SW 12

USPH-S

S

Water Cooler

REV. 05/2012

Pagina 2

Pagina 2

CONFORMANCE STATEMENT

SW 12 has been manufactured with
suitable materials for drinking
water.The unit conform to L.D. 108
dated 25.01.1992. The appliance

and approved by the WRAS
(WATERREGULATION ADVISORY
SCHEME)

Water cooler is:

• EC approved

• Respects EC requirements safety

objectives of the “Low Voltage”
2006/95/CEE;

• Approved for protection requisites

of "EMC" 2004/108/CEE.

1 INTRODUCTION

This manual provides specifications and step by
step procedures for unpacking installation,
operation and maintenance.

• Keep this book for further use.

• When unpacking the unit check about any
transport damage. Anything occured must be
reported to your carrier within 24 hours.

If the unit has been shipped lay or up side
down, wait approx 8 hours before start
up. This is for cooling system safety.

• Make sure that installation and electrical wiring
are carried out by a qualified technician
according to the manufacturer’s instructions
and to the local norms in force. The electrical
system must be equipped with an effective
earth according to the law (46/90)

Before carrying out any maintenance
or cleaning operation, disconnect unit
from power.

The data and characteristics indicated in this
manual do not bind the manufacturer, who
reserves the right for modifications.

Failure to comply with any of these safety
regulations could cause fires, electric
shocks or damage the machine

PLACE OF INSTALATION

• Do not place the machine near inflammable
solvents such as alcohol or diluents.

• Do not install the machine in excessively damp
and dusty places, exposed to direct sunlight,
outdoors or near to heat sources.

Installation in these places could cause fires or

electric shocks.

• The appliance is not suitable for use in open
places.

• During connection of the appliance to the mains
water supply, all preexisting tubes, gaskets and
joints placed between the appliance and the
water mains connection must be replaced with
new material to avoid contamination.

ELECTRIC POWER SUPPLY

• Do not connect or disconnect the machine from
the socket with wet hands.

• Do not damage, modify, stretch, bend or twist
the power cable.

Do not place heavy objects on the power cable.

• Do not connect the machine to a socket together
with other equipment (extensions, 2 or 3 plug
adaptors, etc.)

• Do not use the machine if the power cable is tied
or knotted.

• If smoke, unusual smells or strange noises are
found coming from the machine, disconnect it
immediately from the socket and contact the
local retailer or technical service assistance.
Use of the machine in these conditions could
cause fires or electric shocks.

• Do not spray water on the device; this could
cause electric shocks or fires.

• The appliance must not be installed where
water jets can be generated.

• Use a damp cloth to clean the machine. Do not
use inflammable solvents such as alcohol,
benzene or diluents. If inflammable substances
come in contact with the electrical components
inside the machine, they can cause fires or
electric shocks.

• Before cleaning the machine, switch it off and
disconnect it from power. Whether unit is
electrically connected during cleaning could
cause injuries to persons or damages to the
machine.

000100 0102

MANUFACTURER

Mod.

..................

..........V ..........Hz ..........W ..........A

Freon R134a kg............. ClasseT

MADE IN ITALY

WATER COOLERS

1

5
4

2

3

768

1 Model
2 Power supply
3 Ref. charge
4 Class

5 Watts
6 Cycles
7 Serial number
8 Manufacturing year-month

Pagina 3

Pagina 3

• Cut straps A and remove carton B, polystyrene
D and external plastic bag C.

• Remove the base E.

• Place the appliance in its installation site
(pitc 5).

2.1 ADVICE ON HOW TO PROTECT THE

ENVIRONMENT

Packaging

Packaging material is 100% recyclable.
For its disposal follow your local regulations.
The packaging material (plastic bags, polystyrene
parts etc.) must be kept out of children’s reach as
it could be dangerous.

Information

This appliance does not contain CFCs (the cooling
circuit contains a gas that is not harmful to the
ozone layer).
For further details, please refer to the serial data
plate on the appliance.

Produkt

This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE). By
ensuring this product is disposed of correctly,
you will help prevent potential negative conse­quences for the environment and human health,
which could otherwise be caused by inappropriate
waste handling of this product.

The symbol on the product, or on the
documents accompanying the product,
indicates that this appliance may not be
treated as household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment.

2 REMOVAL OF PACKAGING

Disposal must be carried out in accordance with
local environmental regulations for waste
disposal.For more detailed information about
treatment, recovery and recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.

3

DESCRIPTION OF THEAPPLIANCE

These water coolers are designed to offer
maximum hygiene and easy maintenance.
They are manufactured with a high level perfor­mance.
The direct water cooling system guarantees an
optimal hygiene for factories, offices, communities
and public places.
Can be used free standing or wall tight to avoid
unsightly connections.
Exclusive Projector Design: 2-stream mound­building projector and automatic stream regulator.
Plumbing Connections: enter directly into cabinet.
Waste 24 mm (1”) IPS.
Supply 8 mm (3/7”) IPS.
Finish: stainless steel.

1 Front panel
2 Dispensing water plate
3 Front panel screws
4 Water stream projector
5 Aeration grill (do not cover)
6 Push button actuator
7 Water INLET connection 8 mm (3/7”) with No Return

valve optional
8 Electrical box
9 Thermostat box
10 Water temperature
11 Unit nameplate adjusting screw

Pagina 4

Pagina 4

4 TECHNICAL CHARACTERISTICS

l/h gal/h

Water production

50 13,2

°C °F

Water outlet temperature

8 - 12 46 - 53

Compressor HP 1/4
Rated input W 250
Supply Volt/Hz 230/50-60

Kg Lbs

Net weight

33 73

Kg Lbs

Gross weight

36 79

goz

Freon 134a charge

160 5,6

Conditions of surroundings

Dimensions

Pagina 5

Pagina 5

5 INSTALLATION

Warning! The installation should be
carried out by a qualified operator.

• Remove screws and front panel (pitc 4).

• For wall mounting be carefull while drilling fitting
holes and use anchor bolts (pitc 5).

• Locate a suitable water drain base position and
drill a hole for hose passing through (pitc 6).

• Predispose holes for the water supply pipe and
water supply cable (pitc 11).

• Connect the water supply pipe 8 mm (3/7”) to
the inlet fitting (pitc10).
The No return valve is an optional.

Install a water tap on water inlet line.

• Connect the power supply cable inside the
electrical box (pitc 9).

The supply socket must be equipped
with an efficient earth plate and it
must be sized for the load of the
appliance (see technical characteristics).
Make sure that the mains voltage
corresponds with what is specified on
the data plate.
Make sure that there is an omnipolar
switch above the socket with a
minimum contact break of 3 mm (0.12”)
protected by fuses of suitable
amperage for the absorption of the
appliance itself (see technical
characteristics and data plate).

• Open the water tap G (pitc 11) and adjust the
water flow using a screwdriver on the central
button tap (pitc 8).

5

4

7 8

9

10

11

5 6

F

H

G