Scientific Atlanta 573480 User Manual

Page 1

If you wish to order additional AllTouch® Remote Controls or an additional user’s guide, refer to the following table.

Item Part Number Remote Control 573480 User’s Guide 573497 Rev B

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by Scientific-Atlanta could void the user's authority to operate this equipment.

is a trademark of Scientific-Atlanta, Inc.

8600 AllTouch is a registered trademark of Scientific-

Atlanta, Inc.

AllTouch

Remote Control

VCR

MENU INFO

GUIDE

PPV

MUTE

PREV. DAY NEXT DAY

AUX

CBL

SELECT

FAV

LAST

C H

BAC

V O L

POWER

United States: Scientific-Atlanta, Inc., 4261 Communications Drive, P.O. Box 6850, Norcross, GA 30091-6850; Tel: 770-903-5000; TWX: 810-799-4912; Telex: 0542898 Europe: Scientific-Atlanta Europe Ltd., Home Park Estate, Kings Langley, Herts WD4 8LZ, England; Tel: +44-1-923-266133; Fax: +44-1-923-269018 Asia-Pacific: Scientific-Atlanta (HK) Ltd., Suite 56-57, 5/F New Henry House, 10 Ice House Street, Central, Hong Kong; Tel: 852-2522-5059; Fax: 852-2522-5624

573497 Rev B

REW

PLAY FF

PAUSE RECSTOP

SET-UP BYPASS

User’s Guide

Page 2

Contents

Introducing the AllTouch Remote Control ............................................ 3

What the buttons do ............................................................................ 4

Setting up the remote control to operate your TV................................. 6

Setting up the remote control to operate your VCR .............................. 7

Setting up the remote control to operate other devices.......................... 8

Reprogramming your cable device button............................................ 9

All Search.......................................................................................... 10

Getting your codes............................................................................. 12

Reassigning mode buttons.................................................................. 13

Volume Lock...................................................................................... 14

Disabling/enabling channel control.................................................... 16

Programming the macro buttons........................................................ 17

Troubleshooting ................................................................................. 18

Television setup codes ........................................................................ 20

VCR setup codes................................................................................ 24

TV/VCR combination setup codes...................................................... 27

CD player (Aux) setup codes............................................................. 28

Home automation (Aux) setup codes ................................................. 30

Digital cable audio (Aux) setup codes................................................ 30

Record of codes.................................................................................. 31

Reassigned mode buttons................................................................... 31

Important reminder!.......................................................................... 32

573497 Rev B

Page 3

Introducing the AllTouch Remote Control

Your new AllTouch® Remote Control can do the job of four separate remote controls. In fact, it can control four devices at one time. These can be any combination of:

• Home Terminals or 8600

• Televisions • VCRs • Home automation devices

• Cable audio receivers • CD players

Setup

When you first receive your AllTouch Remote Control, you will have to tell it each brand of equipment you want it to control. We call this setup. The cable mode is already set up for home terminals/HCT s.

In the back of this guide, is a list of numbers starting on page 19. These are setup codes you must use to set up your remote control.

Remember–you must set up the AllTouch Remote Control for each device you would like it to control.

Batteries are required

Your AllTouch Remote Control has a red light that comes on with each button press when the batteries are good. The light blinks twice when the batteries are installed for the first time. If the batteries are low, the red light blinks twice each time you press a button.

Follow these steps to check the batteries and install new ones if necessary.

Home Communications Terminals (HCTs)

POWER

1. Press

Note: If you have not used your remote control in a while, you may have to press

POWER

times to make the red light stay on.

2. Did the red light stay on?

• If yes, the AllTouch Remote Control batteries are good.

• If no, the batteries are inserted improperly or the voltage is low. If you replace the batteries, use two alkaline AAs.

573497 Rev B

several

B C

AUX

VCR

MENU INFO

+-+-

POWER

CBL

T6051

T6052

Page 4

What the buttons do

5 6

8 9

When you know what the buttons do, your AllTouch Remote Control is easy to use. See the drawing below.

All the button functions listed below represent factory setups. Buttons

LAST

HCT are specified.

FAV

T6053

1 VCR Control VCR. 2 AUX Control CD player or

cable digital audio

receiver. 3 TV Control your TV. 4 CBL Control your home

terminal/HCT. 5 POWER Turn on and off your TV,

VCR, AUX, or home

terminal/HCT. 6 INFO While in all modes and

for home terminal or

HCT, display

information about

selected device (for

example, channel

name, number). For

HCT only while in cable

mode, also display the

title and description of

program you are

watching or of program

you have highlighted in

the viewing guide. 7 SELECT While in CBL mode,

choose items from the

on-screen menus. In

other modes, use to

enter channel number. 8 FAV While in CBL or TV

modes, surf from one

favorite channel to the

next.

that work only with an 8600

1234

AUX

POWER

BAC

PLAY FF

SET-UP BYPASS

15 14

CBL

23 22

21 20

VCR

MENU INFO

PPV

MUTE

PREV. DAY NEXT DAY

REW

PAUSE RECSTOP

573497 Rev B

Page 5

What the buttons do, Continued

9 LAST While in any mode, return to last channel viewed or to the

previous menu.

10 CH ▲▼ While in any mode, surf through channels. Tune to the

next higher or lower channel.

11 A B C These macro buttons can be programmed by your cable

operator or subscriber to perform multiple key functions in any mode.

12 NUMBERS While in any mode, change channels by pressing the

number buttons or enter parental control number and pay-per-view access number.

13 NEXT DAY (8600

HCT only) While in the viewing guides, go to the

next day’s schedule or move forward one page.

14 BYPASS While in CBL mode, use RF bypass to switch cable

programming between your home terminal/HCT and TV. Requires optional RF accessories. Your cable company activates this function. While in TV or VCR modes, select an alternate video input source for the device (for example,TV/VCR in VCR mode, TV/Video in TV mode).

15 SET-UP Set up this remote to control the TV, AUX, VCR, and other

devices.

16 VCR Control VCR and AUX device functions.

FUNCTIONS

17 PREV. DAY (8600

HCT only) While in the viewing guides, go to the

previous day’s schedule or move back one page. 18 VOL ▲▼ Adjust volume. 19 MUTE Turn off sound. 20 PPV While in CBL mode, display the list of upcoming pay-per-

view (PPV) programs. For 8600

HCTs: You may purchase

PPV programs automatically.

21 ARROWS For 8600

HCTs: While in CBL mode, highlight items on menus, viewing guides, and screens. For other home terminals: While in CBL mode, use the down arrow button to highlight menu items.

22 GUIDE (8600

HCT only) While in CBL mode, display the

Interactive Viewing Guide to see what’s on cable.

23 MENU While in CBL mode, go to or leave menus.

573497 Rev B

Page 6

Setting up the remote control to operate your TV

To make the remote control work with your TV, follow this procedure. Important! If you are using a TV/VCR combination, you should use the

VCR or TV/VCR combination codes. Go to Setting up the remote control to operate your VCR on the next page.

1. Find the code for your brand of TV in the back of this guide. You may find more than one code for your particular brand. Start with the first choice. Remember: If you are using a TV/VCR combination, use a VCR or TV/VCR combination code.

2. Press and release

, then hold down

SET-UP

until

the red light blinks twice. Note: You may need to wait a few seconds for the

red light to blink twice.

3. Enter your 3-digit TV code–the red light should blink twice again. (If the red light does not blink twice, return to step 1 and try again.)

4. Point your AllTouch Remote Control at your TV and press

POWER

5. Did your TV turn off (or on)?

• If yes, you are finished setting up the remote

control for your TV. Write your TV code on page 31.

• If no, go to step 6. Notes:

• You may want to press VOL ▲▼, MUTE, and CH ▲▼ to

verify that all functions work.

• To disable channel control in TV mode, turn to Disabling/

enabling channel control on page 16 and follow the steps.

6. If your TV did not respond, repeat steps 2 through 5 trying all of the codes (one at a time) under your brand.

7. If your TV still did not respond, turn to All Search on page 10 and follow the steps.

AUX

VCR

POWER

MENU INFO

E D

I U G

PPV

BAC

PREV. DAY NEXT DAY

REW

PLAY FF

PAUSE RECSTOP

SET-UP BYPASS

SET-UP

CBL

SELECT

FAV

T6054

573497 Rev B

Page 7

Setting up the remote control to operate your VCR

To make the remote control work with your VCR, follow this procedure. Important! If you are using a TV/VCR combination, you should set up

your VCR or TV/VCR combination code first, then go back to Setting up the remote control to operate your TV . Use the same VCR code to set up your TV, unless noted in code table on page 15.

1. Find the code for your brand of VCR in the back of this guide. You may find more than one code for your particular brand. Start with the first choice. Remember: If you ar e using a TV/VCR combination, use a VCR code.

2. Press and release

VCR

, then hold down

SET-UP

until

the red light blinks twice. Note: You may need to wait a few seconds for the

red light to blink twice.

3. Enter your 3-digit VCR code–the red light should blink twice again. (If the red light does not blink twice, return to step 1 and try again.)

4. Point your AllTouch Remote Control at your VCR and press

POWER

5. Did your VCR turn off (or on)?

• If yes, you are finished setting up the remote

control for your VCR. Write your VCR code on page 31.

• If no, go to step 6.

VCR

AUX

VCR

POWER

MENU INFO

GUIDE

PPV

T E

BAC

PREV. DAY NEXT DAY

REW

PLAY FF

PAUSE RECSTOP

SET-UP BYPASS

SET-UP

CBL

T6055

E L E

C T

FAV

Notes:

• You may want to insert a tape and try

REW

and program, press

to verify that all functions work. To record a

REC

twice.

PLAY

• All VCR functions also work in TV and CBL modes.

6. If your VCR did not respond, repeat steps 2 through 5 trying all of the codes (one at a time) under your brand.

7. If your VCR still did not respond, turn to All Search on page 10 and follow the steps.

573497 Rev B

Page 8

Setting up the remote control to operate other devices

You can use the

AUX

button on your AllTouch Remote Control to set up

your:

• Cable digital audio receiver

• CD player

• Home automation device

To make the remote control work with other devices, follow this procedure.

1. Find the code for your brand of device in the back of this guide. You may find more than one code for your particular brand. Start with the first choice.

2. Press and release

AUX

, then hold down

SET-UP

until

the red light blinks twice. Note: You may need to wait a few seconds for the

red light to blink twice.

3. Enter your 3-digit device code–the red light should blink twice again. (If the red light does not blink twice, return to step 1 and try again.)

4. Point your AllTouch Remote Control at your device and press

POWER

5. Did your device turn off (or on)?

AUX

VCR

MENU INFO

ID U G

PPV

MUTE

V O L

PREV. DAY NEXT DAY

REW

PAUSE RECSTOP

SET-UP BYPASS

• If yes, you are finished setting up your device. Write your code on page 31.

SET-UP

• If no, go to step 6.

Note: You may want to try several functions of your device to

verify operation. Button operation (for example, CH ▲▼, LAST, INFO, etc.) will depend on the AUX device programmed.

6. If your device did not respond, repeat steps 2 through 5 trying all of the codes (one at a time) under your brand.

7. If your device still did not respond, turn to All Search on page 10 and follow the steps.

CBL

POWER

S E L

FAV

C H

BAC

PLAY FF

T6056

E C

573497 Rev B

Page 9

Reprogramming your cable device button

Your AllTouch Remote Control is already set up to operate a ScientificAtlanta home terminal/HCT. If your remote control loses its code for the home terminal/HCT, you need to reprogram your cable device button. Follow the instructions below.

Notes:

• Not all cable functions work with older Scientific-Atlanta home terminals.

• In the cable mode, the VOL button will not control the volume through the home terminal/HCT unless you program it to do so. See Volume Lock on page 14. The Volume Lock defaults to TV mode.

The code for your brand of home terminal/HCT is 491.

1. Press and release

CBL

, then hold down

SET-UP

until

the red light blinks twice. Note: You may need to wait a few seconds for the

red light to blink twice.

2. Enter

9 1 – the red light should blink twice again. (If the red light does not blink twice, return to step 1 and try again.)

3. Point your AllTouch Remote Control at your home terminal/HCT and press

POWER

4. Did your home terminal/HCT turn off (or on)?

• If yes, you are finished setting up your home

terminal/HCT.

SET-UP

• If no, go to step 5. Note: All VCR functions (

PLAY

mode. To record a program, press

, etc.) also work in CBL

REC

twice.

5. If your home terminal/HCT did not respond, repeat steps 1 through 4.

6. If your home terminal/HCT still did not respond, contact your service provider.

AUX

VCR

MENU INFO

GUIDE

PPV

MUTE

V O L

PREV. DAY NEXT DAY

REW

PAUSE RECSTOP

SET-UP BYPASS

CBL

POWER

FAV

C H

BAC

PLAY FF

T6057

E L E

C T

573497 Rev B

Page 10

All Search

If your device does not respond after trying all of the codes for your brand, try the All Search procedure.

During All Search, the AllTouch Remote Control searches through a library of codes until it finds the right one for your device. The AllTouch Remote Control then completes the setup automatically.

Follow the steps below to do an All Search.

1. Turn on the device that you could not set up using the codes. For example, if all the codes for your brand of VCR did not respond, turn off your VCR. If the device is a CD Player, turn it on and insert a disc.

2. Press and release the appropriate button on the remote control.

Device Button

VCR Auxiliary (such as a CD player) TV HCT/Home Terminal

3. Press and hold

9 9

4. Press

1. The red light blinks twice.

SET-UP

until the red light blinks twice.

VCR

AUX

CBL

5. Point your AllTouch Remote Control directly at the device.

T6058

6. Press

VCR

(

POWER

AUX, TV

(or

, or

PLAY

for CD player) then the appropriate button

CBL

). Repeat this step until your device turns on

or starts to play. You may have to repeat this 50 or 60 times. Important! Be patient and go slowly. Allow enough time for the

device to turn on or for the CD player to start.

573497 Rev B

Page 11

All Search, Continued

7. When your device turns on or starts to play, press and hold

SET-UP

until the red light blinks twice. This step programs the code into the AllTouch Remote Control.

Your remote control now has the correct code for your device. Note: Press several keys on the remote control for the device

(VOL ▲, CH ▲,

PLAY

, etc.) to verify that all functions work

correctly.

8. Next, you need to find your device codes. See Getting your codes on the next page to find the code(s) for your device(s). Write the codes on page 31.

Notes:

• You may want to inset a disc into your CD player and use

PLAY

the

button on the remote instead of the

search. When your CD player starts to play, press

POWER

button to

SET-UP

to lock

in your code.

• If a device is not found, please make note of its brand, model

number, description, size, etc., and contact your service provider.

• When you have searched through the complete device code

library, the red light will blink three times. The search will then start over again from the beginning of the library.

573497 Rev B

Page 12

Getting your codes

After doing an All Search, find your 3-digit device codes. Follow the steps below to find your codes.

1. Press and release the appropriate button for the device on the AllTouch Remote Control. For example, if you are getting the

code for your VCR, press and release

Device Button

VCR

VCR Auxiliary TV HCT/Home Terminal

2. Press and hold

3. Press

9 9

0. The red light blinks twice.

SET-UP

until the red light blinks twice.

VCR

AUX

CBL

4. Press and release the 1, 2, or 3 buttons on the remote control to find each digit of the 3-digit code.

After pressing each button, count the number of times the red light blinks. This number indicates the digit. There is a delay of a few seconds before the blinks start. If the red light does not blink, the digit is zero. Record your findings below.

Press this Record the Number of Blinks Number Button VCR AUX TV

Enter the number of blinks here

and on page 31.

3 1

5. Important! Remember to write the codes on page 31.

6. Repeat steps 1 through 5 for each device.

573497 Rev B

Page 13

Reassigning mode buttons

Y our mode buttons ar e

VCR

AUX, TV

, and

CBL

. They represent your VCR, auxiliary device, television, and your home terminal/HCT. You can reassign these buttons to control other devices if you choose. To reassign a mode button, you copy the features of one button to another button.

For example, you may want your AllTouch Remote Control to control two TVs instead of a TV and a VCR. You can turn your VCR button into a second TV button.

To reassign a mode button, follow the steps below.

1. Press and hold

2. Press

9 9 2

SET-UP

until the red light blinks twice.

. The red light blinks twice.

3. Press the button you want to copy (source button).

4. Press the button you want to reassign (target button). The red light blinks twice.

5. Set up the reassigned button with the correct device code to control your device.

To set up for... Go to page...

TV 6 VCR 7 Other devices (AUX) 8 Cable 9

6. Write your changes and new codes in the following table and on page 31.

Device VCR Aux TV CBL

Reassigned button (New device)

Code

573497 Rev B

Page 14

Volume Lock

After you program your TV code into your remote control, it will automatically control the TV’s volume while operating in the TV, VCR, or CBL modes. You can also program the remote control so that you can control the volume through the HCT or TV/VCR combination while operating in TV, VCR, or CBL modes. We call this Volume Lock.

Note: Volume Lock programming will remain active even if batteries are removed for an extended period of time.

To switch your volume control to a device other than your TV, follow the steps below.

SET-UP

1. Hold down

2. Press

9 9

3. Press the appropriate device mode button ( light blinks twice. Your volume control is now locked to your selected device mode.

Device Button Result

until the red light blinks twice.

CBL

VCR

). The red

Home

CBL

Y our r emote contr ol will now contr ol the

Terminal volume through your home terminal. TV/VCR

VCR

Y our r emote contr ol will now contr ol the

combination volume through your TV/VCR combination.

Important! If you have a TV/VCR combination unit, you need to enter a TV code to control volume. Once you enter the TV code, the volume control will work in any mode. In most cases the TV code is the same as the VCR or TV/VCR combination code already entered, but for the codes noted in the table on page 15, a different TV code is required for volume control.

Note: Your AllTouch Remote Control automatically controls only the volume of your Aux device (CD Player) while in the AUX mode. You cannot lock the volume to the AUX mode.

573497 Rev B

Page 15

Volume Lock, Continued

TV/VCR combinations’ volume control codes:

VCR code TV code

049 065 062 107 074 061 095 068 176 264

Note: All other TV/VCR combinations use the same VCR or TV/VCR code for the Volume Lock sequence to activate volume control.

573497 Rev B

Page 16

Disabling/enabling channel control

This function enables or disables TV and VCR mode controls including Channel Up/Down, Digits 0-9, Last Channel, and Favorite Channel. With this programmable feature, the TV and VCR remains on the correct output channel (either 3 or 4) so that the HCT operates properly.

The channel control in TV and VCR mode is enabled as the factory default.

To disable channel control in TV and VCR modes:

1. Press and hold

SET-UP

until the red light blinks twice.

2. Press

9 9

6. The red light blinks twice.

3. Press CH ▼. The red light blinks twice.

To enable channel control in TV and VCR modes:

SET-UP

1. Press and hold

2. Press

9 9

6. The red light blinks twice.

until the red light blinks twice.

3. Press CH ▲. The red light blinks twice.

Note: When TV and VCR channel control is disabled, the cable mode channel control will be available in these modes.

573497 Rev B

Page 17

Programming the macro buttons

The AllTouch Remote Control provides users with three definable macro buttons (A, B, and C), which can be programmed by the cable operator or subscriber . Pr ogramming one of the macr o buttons enables you to per form several functions by pressing that key such as switching to cable, turning on HCT power , and switching to channel 25.

To program a macro button (A, B, or C):

1. Press and hold

SET-UP

until the red light blinks twice.

2. Press

9 9

5. The red light blinks twice.

3. Press macro button (A, B, or C).

4. Press one of the mode buttons (

VCR

AUX, TV

, or

CBL

5. Press the function button desired. You may use up to three function buttons.

6. Press and hold

SET-UP

until the red light blinks twice.

Each macro button may have up to three functions with each function having no more than four button presses.

To clear a macro button (A, B, or C):

1. Press and hold

2. Press

9 9

SET-UP

until the red light blinks twice.

5. The red light blinks twice.

3. Press macro button (A, B, or C).

4. Press and hold

SET-UP

until the red light blinks twice.

W rite the function of each macro button in the following table.

Macro button Function

573497 Rev B

Page 18

Troubleshooting

Refer to the following table for solutions if you have trouble operating your AllTouch Remote Control.

Problem Possible Cause Check and Correct

The red light •The battery Replace the batteries. Use does not blink voltage is low. two AA alakaline batteries. when you press •The batteries are Check that the batteries’

POWER

. inserted incorrectly. plus (+) and minus (–) symbols

match the illustration inside the battery compartment.

The remote You may have the Press: control does not remote control in • work properly or the wrong mode. • home terminal/ • HCT functions • do not work.

You may have used Follow these steps to program an incorrect code to your remote control with the program the remote correct code: control. 1. Try all the codes listed

VCR

for VCR

AUX

for auxiliary device

for TV

CBL

for cable

under the brand of your device.

2. Try All Search and be sure to go slowly. (See page 10.)

Important! Be sure to point your AllT ouch Remote Contr ol directly at your device when you press

POWER

PLAY

573497 Rev B

Page 19

Troubleshooting, Continued

Problem Possible Cause Check and Correct

The remote You may have used Try All Sear ch again (see page control responds an incorrect code to 10). Keep progressing through to some of the program the remote the library until you discover codes but with control. the code that supports all the wrong result. of your features.

(Unfortunately, many devices use very similar remote contr ol codes. While sear ching the library with All Search, you may have locked onto a similar code for which only some commands work.)

Your device is Your device has not Make a note of the brand, not found been included in number, description (size, etc.), during an the All Search and contact your service All Search. database. provider.

573497 Rev B

Page 20

Television setup codes (Most popular codes listed first)

Television brand 3-digit codes

A-Mark 017

Television brand 3-digit codes

Celebrity 014 Abex 046 Admiral 107 Adventura 060 Aiko 106 Akai 044 Alaron 193, 197 Ambassador 191 Anam 082, 194 Anam National 069 AOC 017, 033, 044, 066,

151, 199 Archer 017 Astro Text 393 Audiovox 017, 106, 194, 465 Baysonic 194 Belcor 033 Bell & Howell 030, 168 Bradford 194 Brockwood 033 Broksonic 017, 250, 477 Candle 044, 060, 070, 200 Carnivale 044 Carver 068 CCE 231, 343

Cineral 106, 465 Citizen 044, 053, 060, 070,

074, 106, 200, 294 Clairtone 199 Concerto 070 Contec 171, 172, 194, 199 Craig 194 Crosley 068 Crown 053, 194 Curtis Mathes 030, 044, 053, 074, 061,

065, 068, 070, 168, 429,

465 CXC 194 Daewoo 465, 033, 053, 105, 106 Daytron 033 Denon 159 Dumont 031, 033 Electroband 014, 199 Electrohome 395, 403, 423 Emerson 250, 477, 033, 052, 053,

168, 172, 191, 192, 193,

194, 196, 197, 199, 250,

294, 296, 477 Envision 044 Fisher 168, 173 Fujitsu 193

573497 Rev B

Page 21

Television setup codes, Continued

Television brand 3-digit codes

Funai 185, 193, 194 Futuretech 194 GE 061, 035, 041, 043,

065, 069, 149, 188,

192, 293, 296, 465 Gibralter 031, 033, 044 GoldStar 070, 015, 033, 044, 046,

120, 192, 423 Gradiente 067, 070, 406 Grunpy 193, 194 Hallmark 192

Harley Davidson 193

Harman/Kardon 092 Harvard 082, 194 Hitachi 159, 165, 046, 052,

070, 293, 423, 427 Infinity 068 Inteq 031 Janeil 060 JBL 068 JCB 014 JVC 067, 083, 174, 196 Kawasho 172 Kaypani 066 KEC 194 Kenwood 033, 044

Television brand 3-digit codes

Kloss 038, 060, 092 KMC 120 KTV 044, 053, 194, 197,

Logik 030 Luxman 070 LXI 061, 068, 162, 168,

Magnavox 068, 034, 038, 042, 044,

Majestic 029, 030 Marantz 044, 068 Matsushita 264 Megatron 017, 159, 192 MEI 199 Memorex 030, 070, 120, 164,

MGA 033, 044, 164, 192 Midland 031, 046, 053, 061,

Minutz 035 Mitsubishi 164, 033, 107, 192,

Motorola 069, 107 MTC 033, 044, 070, 074,

Multitech 194, 231

199, 231, 294

170, 192

110, 193, 200, 201, 400

168, 192

065, 149

255

105, 199

573497 Rev B

Page 22

Television setup codes, Continued

Television brand 3-digit codes

NAD 170, 180, 192 NEC 044, 033, 070 Nikko 044, 106, 192 Noblex 444 Noshi 032 NTC 106 Onwa 194 Optimus 168, 180, 264 Optonica 107, 179 Orion 193, 250, 477 Panasonic 264, 065, 069, 240 Penney 017, 032, 033, 035,

041, 044, 046, 053,

061, 065, 070, 074,

149, 163, 170, 192 Philco 068, 033, 034, 042,

044, 110, 159, 477 Philips 068

Pilot 033, 044, 053 Pioneer 180, 052 Portland 033, 053, 106 Prism 065 Proscan 061 Proton 017, 066, 192 Pulsar 031, 033 Quasar 264, 065, 069, 179

Television brand 3-digit codes

Radio Shack 033, 044, 046, 053,

RCA 061, 032, 033, 043,

Realistic 033, 044, 046, 053, 070,

Rhapsody 197, 199 Runco 031, 044 Sampo 044, 046, 053, 066 Samsung 074, 033, 044, 046,

Samsux 053 Sansei 465 Sanyo 168, 173, 160, 498 Sansui 477 Scimitsu 033 Scotch 192 Scott 033, 192, 193, 194, 250 Sears 029, 061, 068, 070,

Servivox 194 Sharp 107, 179, 053, 171,

Semp 170 Shogun 033

061, 070, 168, 179, 192, 194, 423

052, 065, 104, 149, 188, 292

168, 179, 192, 194

070, 192, 343, 441, 496

160, 162, 163, 168, 170, 173, 185, 192, 193

400

573497 Rev B

Page 23

Television setup codes, Continued

Television brand 3-digit codes

Signature 030 Simpson 200, 201 Sony 014, 025, 094, 125 Soundesign 192, 193, 194, 200 Spectricon 017, 151 Squareview 185 SSS 033, 194 Starlite 194 Supre-Macy 060 Supreme 014 Sylvania 068, 034, 042, 044,

110, 395 Symphonic 185 Tandy 107 Tatung 017, 069 Technics 065, 264 Technol Ace 193 Techwood 017, 065, 070 Teknika 030, 033, 053, 068,

070, 074, 106, 164,

193, 194, 200, 326

Television brand 3-digit codes

Telefunken 070 TMK 070, 191, 192 Toshiba 170, 074, 163, 168 Tosonic 199 Totevision 053 Trical 171 Universal 041 V ector Research 044 Victor 067 Vidikron 068, 256 Vidtech 033, 192 Viking 060, 326 Wards 030, 033, 034, 035,

Yamaha 033, 044 Zenith 031, 030, 106 Zonda 017

041, 042, 043, 044, 068, 070, 094, 110, 125, 188, 192, 193

573497 Rev B

Page 24

VCR setup codes (Most popular codes listed first)

VCR brand 3-digit codes

Admiral 062

VCR brand 3-digit codes

Daytron 034 Adventura 014 Aiko 292 Aiwa 014, 051 Akai 055, 063, 067, 075,

120 American High 049 Asha 254 Audiovox 051 Beaumark 254 Bell & Howell 118 Broksonic 016, 223, 198, 135,

225, 309, 375, 493 Calix 051 Canon 049, 116 Capehart 034 Carver 095 CCE 086, 292 Cineral 292 Citizen 051, 292 Colt 086 Craig 051, 061, 086, 254,

285

Denon 056 Dynatech 014 Electrohome 051 Electrophonic 051 Emerex 046 Emerson 198, 223, 493, 014,

016, 050, 051, 057, 075, 082, 102, 135, 222, 225, 226, 292,

308, 309, 375 Fisher 118, 061, 068, 080 Fuji 047, 049 Funai 014 Garrard 014 GE 062, 074, 049, 079,

216, 254 Go Video 246, 293, 446 Goldstar 051, 052 Gradiente 014, 022, 422 Grundig 209

Harley Davidson 014

Harman/Kardon 052, 089

Curtis Mathes 049, 055, 074, 176 Cybernex 065, 254 Daewoo 292, 034, 059

Harwood 082, 086 Headquarter 060 HI-Q 061

573497 Rev B

Page 25

VCR setup codes, Continued

VCR brand 3-digit codes

Hitachi 056, 014, 055, 079,

096, 119, 180, 410

Jensen 055

VCR brand 3-digit codes

Mitsubishi 057, 062, 075, 081,

089, 187, 457

Motorola 049, 062

JVC 081, 022, 055, 220 KEC 051, 292 Kenwood 052, 055, 081 KLH 086 Kodak 049, 051 Lloyd’s 014, 222 Logik 086 LXI 051 Magnasonic 292 Magnavox 014, 095, 049, 053,

124, 163 Magnin 254 Marantz 049, 095 Marta 051 Matsushita 049, 176, 468 MEI 049 Memorex 014, 049, 051, 053,

060, 061, 062, 118,

176, 254 MGA 057, 075, 254

MGN Technology 254

Minolta 056, 119

MTC 014, 254 Multitech 014, 086 NAD 072 NEC 052, 054, 055, 081,

096, 118 Nikko 051 Nikon 048, 267 Noblex 254 Olympus 049, 240 Optimus 051, 062, 072, 118,

176, 446, 468 Optonica 076 Orion 016, 198, 309, 493 Panasonic 176, 049, 091, 116,

239, 240, 392, 468 Penney 049, 051, 052, 054,

056, 068, 254 Pentax 056, 079, 119 Philco 049, 223, 493 Philips 049, 076, 095, 124 Pilot 051 Pioneer 072, 081, 176 Portland 034

573497 Rev B

Profitronic 254

Page 26

VCR setup codes, Continued

VCR brand 3-digit codes

Proscan 074, 216 Protec 086 Pulsar 053, 065 Quarter 060 Quartz 060 Quasar 176, 049, 091, 468 Radio Shack 014, 051 Radix 051 Randex 051 RCA 049, 062, 216, 056,

074, 079, 091, 119, 120, 163, 254

Realistic 014, 049, 051, 060,

061, 062, 076, 080,

118 Ricoh 048, 267 Runco 053 Salora 089 Samsung 254, 059, 065, 067

Sanky 053, 062 Sansui 014, 055, 081, 096,

285, 493 Sanyo 060, 061, 118, 254 Scott 057, 059, 135, 198,

224, 225, 226 Sears 014, 049, 051, 056,

060, 061, 068, 080,

118, 1 19 Sharp 062, 076

VCR brand 3-digit codes

Shintom 086 Shogun 065, 254 Singer 086 Sony 014, 046, 047, 048,

049, 267 STS 056 Sunpak 267 Sylvania 095, 049, 014, 057,

124 Symphonic 014 Tatung 055 Teac 014, 055 Technics 049, 176 Teknika 014, 049, 051 Thomas 014 TMK 050, 222, 254 Toshiba 059, 057, 080, 224,

226, 380 Totevision 051, 254 Unitech 254 Vector 059 Vector Research 052, 054 Video Concepts 054, 059, 075 Videosonic 254 Wards 014, 049, 056, 061,

062, 074, 076, 086,

095, 163, 226, 254 White

Westinghouse 292 XR-1000 014, 049, 086 Yamaha 052 Zenith 014, 053, 047, 048

573497 Rev B

Page 27

TV/VCR combination setup codes

TV/VCR combination brand 3-digit codes

Broksonic 016, 106, 493 Curtis Mathes 049 Daewoo 292 Emerson 016, 106, 493 Funai 014 GE 049, 074, 062, 254 Hitachi 014 MGA 254 Magnavox 049, 095, 014 Memorex 051, 176 Mitsubishi 062

TV/VCR combination brand 3-digit codes

Orion 016, 493 Panasonic 049 Penney 049, 254 Quasar 049, 176 RCA 049, 074, 062 Sansui 014, 493 Sanyo 254 Sears 014, 051 Symphonic 014 Zenith 014

573497 Rev B

Page 28

CD player (Aux) setup codes

CD Player brand 3-digit codes

ADC 032 Adcom 169, 248 Aiwa 138, 171 Akai 170 Audio Alchemy 208 Audio-T echnica 184 BSR 208, 259 Burmester 434

California Audio Lab 043

Carrera 208 Carver 171, 193, 451 DAK 259 Denon 017 DKK 014 Emerson 169, 178, 319, 483 Fisher 062, 102, 188, 193,

356 Garrard 259, 294, 407, 434 GE 023 Genexxa 046, 178, 319 Harman/Kardon 440 Hitachi 046, 169 JVC 086 Kenwood 042, 051, 062, 204 Kodak 301 Krell 171 Kyocera 032 Linn 171 Luxman 107

CD Player brand 3-digit codes

LXI 319 Magnavox 171, 319 Marantz 043, 171, 194 McIntosh 301 MCS 043 Mission 171 MTC 434 NEC 248 Nikko 178, 184, 188 NSM 171 Onkyo 115 Optimus 014, 046, 051, 062,

101, 159, 193, 208, 210, 294, 319, 356,

434, 440, 451, 482 Panasonic 043, 317, 381, 766 Parasound 208, 434 Philips 171, 301 Pioneer 046, 258, 319, 482 Proton 171 QED 171 Quasar 043 RCA 023, 067, 169, 193,

319, 778 Realistic 169, 178, 193, 194,

434 Rotel 171, 434 SAE 171 Sansui 171, 216, 319 Sanyo 101, 193

573497 Rev B

Page 29

CD player (Aux) setup codes, Continued

CD Player brand 3-digit codes

Scott 169, 178, 319 Sears 319 Sharp 051, 194 Sherwood 194, 210, 440 Sony 014, 199, 619, 741 Soundesign 159 STS 032 Tascam 434

CD Player brand 3-digit codes

Teac 188, 194, 407, 434 Technics 043, 317 Vector Research 208 Victor 086 Wards 171, 067 Yamaha 050, 184, 201 Yorx 475

573497 Rev B

Page 30

Home automation (Aux) setup codes

Brand 3-digit codes

Cableshare 551 GE 254 One For All 181 Radio Shack 254

Brand 3-digit codes

Security System 181

Universal X10 181 X10 181

Digital cable audio (Aux) setup codes

Brand 3-digit codes

Jerrold 473, 534 Scientific-Atlanta 474 Starcom 473

573497 Rev B

Page 31

Record of codes

Use this table to write your codes.

CBL TV VCR AUX

Reassigned mode buttons

Use this table to write your reassigned mode buttons.

573497 Rev B

Device VCR AUX TV CBL

Reassigned button (New device)

Code

Page 32

Important reminder!

When you pick up most remote controls, you press a button to perform a specific action. Since the AllTouch Remote Control can control several different devices, you must first press a mode button and then the button for the specific action. The remote control remains in this mode until you press another button.

Example:

If you want to change the channel on your HCT/home terminal, press

CBL

the change the channel on your VCR, press the

CH ▲▼ button. The remote control remains in the VCR mode until you press another mode button.

button and then the CH ▲▼ button. If you now want to

VCR

button and then the

AUX

POWER

CBL

Press this button first to put remote control

SELECT

in CBL mode.

VCR

MENU INFO

GUIDE

PPV

MUTE

V O L

BAC

PREV. DAY NEXT DAY

REW

PLAY FF

PAUSE RECSTOP

SET-UP BYPASS

FAV

LAST

C H

Then, press this button to change channels on your HCT/home terminal.

T6059

573497 Rev B