Scientific Atlanta 15-100 User Manual

8-in-1 LCD Remote

15-100

Please read this user’s guide before installing,

setting up and using your new product

www.radioshack.com

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Battery Use And Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

To Install Batteries: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Programming a Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Programming a Device by Selecting Its Brand . . . . . . . . . . . 11

Programming a Device by Manually Entering Its Code . . . . . 12

Programming a Device by Searching for Its Code . . . . . . . .14

Using My System Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Control Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

About Control Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

About Device Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Programming My System Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Learning Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Programming a Learned Key . . . . . . . . . . . . . . . . . . . . . . . . .17

Deleting a Single Learning Key. . . . . . . . . . . . . . . . . . . . . . . . 17

Deleting All Learned Keys in a Specific Mode . . . . . . . . . . . . 18

Using Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Programming Keymover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Restoring a Single Keymover Key. . . . . . . . . . . . . . . . . . . . . . 19

Restoring All Keymover Keys in a Single Mode . . . . . . . . . . . 19

Programming Favorite Channel Scan . . . . . . . . . . . . . . . . . . . . . . .20

Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Setting the Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Setting Time Macros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Setting a Daily Time Macro. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Setting a Weekly Time Macro. . . . . . . . . . . . . . . . . . . . . . . . .23

Deleting a Time Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Locking Volume Control to One Mode (Global Volume Lock). 24

Unlocking Volume Control for a Single Device (Individual

Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Unlocking All Volume Control (Restoring Global Unlock) . . . 25

Using Text Edit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Resetting the Remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

RF Emissions Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Limited 90-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . .41

Setup Codes for Audio Accessories . . . . . . . . . . . . . . . . . . . .42

Setup Codes for Audio Receivers. . . . . . . . . . . . . . . . . . . . . .42

Setup Codes for Cable Set-top Boxes . . . . . . . . . . . . . . . . . . 46

Setup Codes for Cable/PVR Combos . . . . . . . . . . . . . . . . . . . 48

Setup Codes for CD Players . . . . . . . . . . . . . . . . . . . . . . . . . .49

Setup Codes for DBS/PVR Combo Boxes . . . . . . . . . . . . . . . .51

Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . . .52

Setup Codes for DVD/PVR Combos. . . . . . . . . . . . . . . . . . . . .56

Setup Codes for Home Automation . . . . . . . . . . . . . . . . . . . .56

Setup Codes for PVRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Setup Codes for Satellite Set-top Boxes . . . . . . . . . . . . . . . .58

Setup Codes for TV/DVD Combos . . . . . . . . . . . . . . . . . . . . . .60

Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . .60

Setup Codes for TV/VCR/DVD Combos . . . . . . . . . . . . . . . . . .62

Setup Codes for Video Accessories . . . . . . . . . . . . . . . . . . . .63

Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

INTRODUCTION

Thank you for purchasing a RadioShack 8-in-1 LCD Remote. Your remote lets you control up to eight home entertainment devices with one easy-to-use, compact unit.

After installing batteries (see next section), you can immediately use the RadioShack 8-in-1 LCD Remote to control Sony home entertainment devices, and a Dish Network satellite receiver. To control other brands, perform the instructions in Programming a Device. For best results, please read and perform all the remaining instructions. Also, keep this guide for future reference.

•LCD Screen – A two-line LCD display

• My System Mode – a custom mode that

groups the most-often-used keys in different modes together for operating convenience in one mode

• Macros – for instant activation of favorite

key sequences

• Learning – to capture unique functions from

your devices’ original remote controls

• Direct Code Setup – for easy device

programming with setup codes

• Innovative Code Search – allows setup of

your devices without looking up codes

• Favorite Channel Scan – for easy channel

surfing of favorite channels

• Vo lu me L oc k – to assign volume controls to

individual devices or to one global device

• Extensive Code Library – largest and most

efficient group of IR remote control codes for virtually every current brand and make

•Text Edit – You can use the keypad on your

remote to edit and enter text that appears on the LCD screen

• Language Selection – You can select

either English or Spanish as the remote’s interface language

INSTALLING BATTERIES

Yo u r RadioShack 8-in-1 LCD Remote requires four AAA batteries (not supplied) for power.

Battery Use And Safety

• Use only fresh batteries of the required size and

recommended type.

• Do not mix old and new batteries, different types of

batteries (that is, standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.

CAUTION: If you do not plan to use the remote for an extended period, remove the batteries. They can leak chemicals that can damage electronic parts.

WARNING: Dispose of old batteries promptly and properly. Do not burn or bury them.

To Install Batteries:

1. Open the battery compartment cover (located on

the back of the remote).

2. Place the AAA batteries in the compartment and

match the + and - polarity symbols inside.

3. Replace the cover. NOTE: The RadioShack 8-in-1 LCD Remote will not

lose any setup configurations, even when it loses power.

FEATURES AND FUNCTIONS

Use the illustration below to locate features on the RadioShack 8-in-1 LCD Remote and then study the Key Charts (on the next three pages) to learn how they function.

To find out what type of devices can be controlled by each device key after programming, see “Device Table” on page 9.

Key Charts

Press this key… To…

Enter programming mode.

Turn the selected device on or off, or run the macro you programmed for the Power button (see “Setting the Power Macro” on page 20 for more information).

Select a device to control.

Display the menu for the selected device.

Display the menu for the PVR.

Display the program guide for the selected device.

Move the cursor in the program guide and menu screens.

To choose options in the LCD menu screens and to tune programs from the program guide.

Scroll up or down the menu of your PVR or cable/satellite box one page at a time.

Choose options from the selected device's menu or guide.

Return to live TV on your PVR.

Press this key… To…

Exit the selected device's menu, guide, or program.

Select the next or previous channel. Select the next or previous chapter

on some DVD player models.

Increase or decrease the sound level. NOTE: When the device that is set up

does not support volume functions, the remote will send volume for TV.

Turn the sound off or on.

Switch the TV's, VCR's, CBL/SAT’s, or DVD’s input to view TV or video programs, or to act as your cable box's A/B switch.

Recall the last-viewed channel.

Scan favorite channels (and/or all channels). See “Programming Favorite Channel Scan” on page 20 and “Using Channel Scan” on page 20.

Use MY SYSTEM to create a custom mode with favorite remote control keys from different devices in your home theater system. See “Using My System Mode” on page 15.

Directly enter channels (for example, 09 or 31). You can also use the keypad for text editing and entering the manufacturer’s codes for your home entertainment device. See “Using Text Edit” on page 25 and “Programming a Device” on page 11.

Input channel number entries on some TV models or make a selection on a device's menu.

Press this key… To…

Control your VCR, DVD player, or Vid eo On D ema nd ( VO D) i f ava ilab le on your cable/satellite service.

Control the functions of your PVR.

Control the Picture in Picture (PIP) functions of your TV or VCR.

Record a video program on a recordcapable device (press twice).

Use the light bulb key to turn LED backlighting on or off. Press and hold this key to display the time and date on the LCD. The time and date will display only if the clock has previously been set.

Set the sleep timer of your selected device. This is only available if your device has a sleep function.

Program macros. You can program macro sequences on any of these three keys.

Device Table NOTE: Please refer to the table below when

After programming, the RadioShack 8-in-1 LCD Remote will be able to control the following types of devices:

performing the instructions in “Programming a Device” on page 11.

Device Key Controls these types of devices

Any device type can be assigned via the LCD menu. Device types include: TV, VCR, DVD, AUX, Cable, Satellite, DSS, Receiver, PVR, Amp, Misc. Audio, CD, Home Automation, Video Accessories, and Tuner.

SETTING THE LANGUAGE

Before using your RadioShack 8-in-1 LCD Remote, you must set the default language (either English or Spanish). You cannot use your remote control until you have set the language. To set the language for your remote control for the first time, perform the following steps:

1. After the remote powers up, the LCD displays

English OK or  .

2. Press OK for English or press until Spanish is

displayed. Press OK.

3. The LCD displays Success and returns to normal

operation. To change the language after the initial setup, perform

the following steps:

1. Press and hold P until the LCD displays

Code Set OK or  . The remote is

now in the programming mode.

2. Use the or keys to scroll through the LCD

display until Language is displayed.

3. Press OK once.

4. To set the language to English, press OK once. To set

the language to Spanish, use the  to scroll to

Spanish. Press OK to select Spanish as the remote

control’s language.

5. To exit this menu, press EXIT once, or use the 

key to return to the previous menu.

SETTING THE CLOCK

To set the clock on your remote control, perform the following steps:

1. Press and hold P until the LCD displays

Code Set OK or  . The remote is

now in the programming mode.

2. Use the or keys to scroll through the LCD

until Clock set is displayed.

3. Press OK once.

4. The LCD displays the time as previously set, if any.

The first set is the hour. The second set is the

minutes. In the position following the numbers,

the LCD displays A or P for A.M. or P.M.

5. While the number for the first digit is flashing, use

the or keys to select the correct digit. You can

also change the time by pressing the number keys

on your remote control’s keypad.

6. Use the key to change to the next digit, until the

last digit is set. Use  to go back to the previous

digit.

7. After you have set the correct time, use the key to

cursor over to A or P.

8. Use the or keys to select either A or P.

9. Press OK once.

10. The LCD displays Success.

11. The LCD displays a day of the week. Use the or

keys to change the day if it is not correct.

12. Press OK once. The day is now set.

13. The LCD displays Success. NOTE: The LCD does not display the clock on the

screen during normal operation. To view the current time, press and hold the Light bulb key until the LCD displays the time. The clock is used for timed macros. For more information on timed macros, see “Setting Time Macros” on page 22.

PROGRAMMING A DEVICE

The RadioShack 8-in-1 LCD Remote comes preprogrammed to operate Sony TVs, VCRs, DVD players, and audio devices, as well as a Dish Network satellite receiver. To control devices other than these default brands, follow these steps; otherwise, skip this section.

Before proceeding, find the codes for the devices you want to program in Manufacturer's Codes and write them down or highlight them.

The RadioShack 8-in-1 LCD Remote offers three methods for programming a device. You can program a device by selecting its brand (for the top 25 brands only), by manually entering its ID code into the remote control, or by searching for the code.

Programming a Device by Selecting Its Brand

1. Turn on the device (for example, DVD player) and,

if needed, load media (for example, a DVD).

2. Press and hold P until the LCD displays

Code Set OK or  .

3. Press OK.

4. The LCD displays Brand.

5. Press OK. The LCD displays Press Mode or 

.

6. Select the mode on the remote that you would like

to set (for example, TV).

7. The LCD displays Setup CBL. Use the  keys

to scroll through the different types of devices to

set up. Press OK.

8. Select the brand of device you want to control (for

example, Sony), by using the  keys to scroll

through the brand list. You can also select your

brand by using your keypad like the keys on a cell

phone, to jump from letter to letter (for example,

press 2 repeatedly to select either A, B, or C). Press

OK.

9. Aim the remote control at your device (for

example, TV). Press any key but OK , , ,  or

EXIT to test that the remote control works with your

device. Use the  keys to select a different code

within the same brand, if any. Press OK to save.

10. The LCD displays Success.

11. The LCD displays Edit Text. This option allows

you to change the default display for this mode

from the brand of the device (for example, Sony) to

a personalized display (for example, My TV). Press

OK to edit text, or press  to exit without text

editing. See steps 4-5 of “Using Text Edit” on

page 25.

Programming a Device by Manually Entering Its Code

1. Turn on the device (for example, DVD player) and,

if needed, load media (for example, a DVD).

2. Press and hold P until the LCD displays

Code Set OK or  .

3. Press OK once. The LCD displays Brand.

4. Use the  keys to scroll through the

LCD display until it displays ID Set.

5. Press OK.

6. The LCD displays Press Mode OK or  .

Press the mode on the remote for the device you

want to program (for example, TV).

7. The LCD displays Enter ID. Press OK. Enter the

first five-digit code for your device. As you enter

the code numbers, each number displays on the

LCD from right to left.

8. Press OK to confirm the code. NOTE: If you do not press OK, the remote does not

9. The LCD displays Test followed by the code you

NOTE: At this point, you can use function keys other

10. Press OK once. The LCD displays Success. NOTE: If you cannot find a code that works, see

11. The LCD displays Edit Text. This option allows

12. Repeat steps 1 to 11 for each device you want to

save the code you entered.

entered (for example, Test 10000).

than OK,  and test the code.

“Programming a Device by Searching for Its Code” on page 14.

you to change the default display for this mode

from the code of the device (for example, 10000) to

a personalized display (for example, My TV). Press

OK to edit text, or press  to exit without text

editing. See steps 4-5 of “Using Text Edit” on

page 25.

control. For future reference, write down each

working device code in a safe place.

EXIT (for example, POWER) to

AUX Code

Device Type:___________________

CD Code

Device Type:___________________

DVD Code

Device Type:___________________

AUD Cod e

Device Type:___________________

SAT/CBL Code

Device Type:___________________

TV Code

Device Type:___________________

PVR Code

Device Type:___________________

VCR Code

Device Type:___________________

Programming a Device by Searching for Its Code

If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code. For example, to search for a code for your TV:

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Press OK.

3. Use the key to scroll through the LCD display

until the LCD displays Search.

4. Press OK once.

5. Press the mode key on the remote for the device

you want to program (for example, TV).

6. The LCD displays Setup CBL. Use the  keys

to select the device type you want to set up.

7. Press OK.

8. The LCD displays Press Test Key. At this point,

press the test key you would like the remote to

transmit every time it moves to the next code

during the search.

9. The remote displays the next code in the list. Use

the  keys to scroll through the codes. The LCD

displays the code for the current devices (for

example, 10000) and transmits your test function.

10. If the TV responds to your test function (for

example, POWER), press OK. The LCD displays

Success. NOTE: The remote transmits the test key you pressed

in step 8 every time the  or key is pressed. If desired, within each code, any function key except the arrows, OK, and EXIT can be used for testing also.

11. The LCD displays Edit Text. This option allows

you to change the default display for this mode

from the code of the device (for example, 10000) to

a personalized display (for example, My TV).Press

OK to edit text, or press  to exit without text

editing. See steps 4-5 of “Using Text Edit” on

page 25.

12. To search for other device codes, repeat steps 1 to

12, substituting the appropriate device key.

USING MY SYSTEM MODE

The RadioShack 8-in-1 LCD Remote includes a custom Home Theater mode. After the My System key is programmed, it will allow you to access four groups of remote control keys without having to change device modes.

Control Organization About Control Groups

For Home Theater programming, the remote control’s keys are grouped by type of control into the following four control groups:

Playback Group: Transport Controls

(Rewind, Play, Fast Forward, Stop, Pause, Record, Skip Forward, and Skip Back)

Audio Group: VOL, VOL, and

MUTE

Channel Group: CH, CH, TV/

VCR, Keypad (0 – 9), FAV Scan, ENTER, LAST, SLEEP, and INFO

Menu Group: Cursor Controls (Up,

Down, Left, and Right), SELECT, PAGE+, PAGE-, MENU, INFO, GUIDE, and EXIT

About Device Modes

Moreover, the above Control Groups can be used in all modes.

Factory Default Settings

At the factory, the Control Groups are assigned the following modes as default settings:

Playback Group: VCR Audio Group: TV Channel Group: CBL Menu Group: CBL

If the default settings fit your needs, you can skip programming this mode. Otherwise, perform the steps in the following section to assign device modes to the Control Groups.

PROGRAMMING MY SYSTEM MODE

1. Press and hold P until the LCD displays

Code Set OK or  . Use the 

keys to sc roll throug h the LCD unt il My

System OK or   is displayed.

Press OK.

2. The LCD displays Channel OK or . Press OK.

3. The LCD displays Press Mode or .

4. Press the mode key for the device you want to

control the channel (for example, TV). The LCD

displays Success TV.

5. The LCD displays Volume OK or . Press OK.

Press the mode key for the device that you want to

control volume (for example, AUDIO). The LCD

displays Success.

6. The LCD displays Transport OK or . Press OK.

7. Press the mode key for the device you want to

control transport (for example, VCR). The LCD

displays Success VCR.

8. The LCD displays Menu Nav OK or . Press OK.

9. Press the mode key for the device you want to

control menu navigation (for example, CBL/SAT).

The LCD displays Success SAT.

10. When programming is complete, the LCD displays

Complete and exits the My System setup.

USING LEARNING

The RadioShack 8-in-1 LCD Remote includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g.,VCR T

racking Up or Down). However, there are some

considerations

Learning Precautions

• Your original remote controls must be in working

order for learning to work properly.

• Learned keys are mode-specific, so each one can

store a unique function for each mode.

• Learning capacity is approximately 34 to 50 keys,

depending on the code being learned.

• Some keys cannot be learned: Mode keys (for

example, TV), P, and the Light bulb key.

• Certain device functions are not learnable,

including multi-frequency types, some high frequency ones, and other unusual formats.

• For optimum learning, avoid high levels of ambient

light such as natural sunlight or energy-efficient fluorescent lights.

NOTE: Please have your original remote controls

handy before programming learning.

Programming a Learned Key

1. Press and hold P until the LCD displays

Code Set OK or  . Use the 

keys to scroll through the LCD display

until Learn is displayed. Press OK.

2. The LCD displays Add Learn OK or . Press OK.

3. The LCD displays Press Mode or .

4. Press a mode key once (i.e., TV, VCR , PVR, CBL/SAT,

CD, DVD, AUX, or AUDIO) to assign a mode to learn

onto.

5. Place the RadioShack 8-in-1 LCD Remote head-to-

head (about 2" apart) from your original remote

control. Also locate the key (on your original

remote control) that you want the RadioShack 8-

in-1 LCD Remote to learn.

6. Press the key on your RadioShack 8-in-1 LCD

Remote that wish to assign learning.

7. On the original remote, press and hold the key.

Continue holding the key on the original remote

until the RadioShack 8-in-1 LCD Remote’s LCD

displays either Success or Learn Fail. NOTE: Immediately after you have pressed the key

that will learn, the LED flashes rapidly and the LCD displays Learning. The remote times out after five seconds and returns to step 6.

8. Repeat steps 4 through 7 for another mode and/or

key or press EXIT to exit programming. Repeat

steps 5 through 7 if learning failed.

Deleting a Single Learning Key

his process returns the key to its original programmin

g for the mode you select. You can also delete learned programming by teaching a different function to the key (see “Programming a Learned Key” on page 17).

1. Press and hold P until the LCD displays

Code Set OK or  . Use the  keys to scroll through the LCD display

until Learn is displayed. Press OK.

2. Use the  keys to scroll through the

LCD display until Dlt Learn is displayed. Press

OK.

3. The LCD displays Press Mode or .

4. Press the mode key once (i.e., TV, VCR , PVR, CBL/

SAT, CD, DVD, AUX, or AUDIO) for the mode you want to delete the learned key from.

5. The LCD displays DLT Key or  . Press OK.

6. The LCD displays Select Key or .

7. Press the key containing the learned function to be

deleted. The LCD displays Are U Sure OK or .

8. Press OK. The LCD displays Success.

9. Repeat steps 5 through 7 for another key.

Deleting All Learned Keys in a Specific Mode

1. Press and hold P until the LCD displays

Code Set OK or  . Use the  keys to scroll through the LCD display

until Learn is displayed. Press OK.

2. Use the  keys to scroll through the LCD

display until Dlt Learn is displayed. Press OK.

3. The LCD displays Press Mode or .

4. Press the mode key once (i.e., TV, VCR , PVR, CBL/

SAT, CD, DVD keys for that mode.

5. The LCD displays DLT Key. Press  until the

LCD displays DLT All. Press OK.

6. The LCD displays Are U Sure OK or . Press OK.

7. The LCD displays Success and exits

programming.

8. Repeat steps 3 to 7 for another mode.

, AUX, or AUDIO), to clear all learned

USING KEYMOVER

The RadioShack 8-in-1 LCD Remote includes a Key mover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode).

PROGRAMMING KEYMOVER

For example, if your DVD player does not have volume control, you can map those keys (i.e., VOL, VOL,

and MUTE) from the TV mode to DVD mode as follows:

1. Press and hold P until the LCD displays

Code Set OK or  . The remote is now in the programming mode.

2. Use the or keys to scroll through the

LCD display until Key Mover is displayed. Press OK.

3. The LCD displays Move Key. Press OK.

4. The LCD displays Press from Mode.

5. For the source mode, press a desired device key

once (i.e., AUX, CBL/SAT, CD, TV, DVD, AUDIO, VCR, or PVR). For this example, press TV once.

6. The LCD displays Press From Key. For the source

key, press a key to be moved once. For this example press VOL once.

7. The LCD displays Press To Mode. For the

destination mode, press a desired device key once (i.e., AUX, CBL/SAT, CD, TV, DVD, AUDIO, VCR, or PVR). For this example, press DVD once.

8. The LCD displays Press To Key. For the

destination key, press a key to be moved once. For this example press VOL once.Upon keymoving, the LCD displays Success.

9. Repeat steps 3 to 8 to move additional keys. For this

example, repeat steps 3 to 8 two more times to map the remaining volume control keys, substituting VOL and MUTE as source and destination keys in

steps 6 and 7. Upon completion of the above procedure, you can now use your RadioShack 8-in-1 LCD Remote to control the TV’s volume and mute in the DVD mode, as well as in the TV mode.

Restoring a Single Keymover Key

1. Press and hold P until the LCD displays

Code Set.

2. Use the or keys to scroll through the

LCD display until Key Mover is displayed. Press

OK.

3. The LCD displays Move key.

4. Use the or keys to scroll to Clear Move and

press OK.

5. The LCD displays Press from Mode.

6. Press the source mode once where the keymoved

key is stored.

7. The LCD displays Press From Key. Then press

the source key once. Upon key restoration, the LCD

displays Success.

8. If desired, repeat steps 4 through 6 to restore

another key.

Restoring All Keymover Keys in a Single Mode

1. Press and hold P until the LCD displays

Code Set.

2. Use the or keys to scroll through the

screen until Keymover is displayed. Press OK.

3. Use the or 

OK.

4. The LCD displays Press Mode or . Press the

mode you want to delete all keymoved keys from.

5. The LCD displays Are U Sure. Press OK.

6. The LCD displays Success and exits.

keys to scroll to Clear All. Press

PROGRAMMING FAVORITE CHANNEL SCAN

The remote allows you to store a list of up to 10 favorite channels, in any order, that are immediately scanned when you press FAV (SCAN).

NOTE: You can only store channels from one device

for Favorite Channel Scan.

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the use the or keys to scroll

through the LCD display until Fav Ch is

displayed. Press OK.

3. The LCD displays Select Mode or .

4. Select the mode you want to program for Favorite

Channel Scan (for example, TV).

5. The LCD displays 1st Fav OK or . Press OK.

6. The LCD displays Enter Chan OK or . Enter a

channel number (for example, 039). Press OK. NOTE: If you press  after programming your first

Favorite Channel, the remote saves the last Favorite Channel selection and exits back to the main Favorite Channel screen.

7. The LCD displays 2

Enter the next channel number (for example, 055).

Press OK.

8. Continue entering channel numbers until you get

up to 10 channels programmed.

9. As soon as you enter the 10th channel, the LCD

displays Success and exits (if you decide you

need fewer than 10 channels, then press EXIT or

). NOTE: Whenever you want to add or replace one or

more favorite channels, all previously entered favorite channels are cleared.

Fav CH OK or . Press OK.

USING CHANNEL SCAN

Use FAV (SCAN) to start a three-second scan of all favorite channels (if programmed; see “Programming Favorite Channel Scan” on page 20) or all channels (if Favorite Channel Scan is not programmed).

1. Press a device key.

2. Press SCAN once.

3. To stop scanning channels at any time, press any

key once.

SETTING THE POWER MACRO

You can use your new RadioShack 8-in-1 LCD Remote to program a power macro that turns your devices off or on in the sequence you choose.

To set the Power macro:

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the or keys to scroll through the

LCD display until Macro is displayed. Press OK.

3. The LCD displays PWR Macro. Press OK.

4. The LCD displays Add Macro. Press OK. The LCD

displays Press Mode IN or  .

5. Press the mode key for each device you want to add

to the power macro in the order they should

execute when the macro is activated.

6. The LCD displays Hold P to save or  after the

first mode key is pressed.

7. After entering the modes, press and hold P until

the LED blinks twice, then release. The LCD

displays Success. Now, when you press and hold the Power key for about 2 seconds, the remote executes the series of commands you entered.

NOTE: You may not include the user keys in the Power macro. User keys are any key other than the mode keys.

To Clear the Power Macro

To clear the Power macro, repeat steps 1-3 above, then perform the following steps:

1. The LCD displays Add Macro.

2. Press   until the LCD displays DLT Macro.

Press OK.

3. The LCD displays Are u sure OK or . Press OK.

The LCD displays Success and the remote exits.

SETTING KEY MACROS

Yo u r RadioShack 8-in-1 LCD Remote allows you to set up key macros to activate certain ke ys in a spe cific order. For example, you can set up a key macro to change the channels on your TV, raise or lower the volume, and start recording on your VCR, all with the touch of one key. The M1, M2, and M3 keys are reserved for macros.

To set a key macro, perform the following steps:

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the or keys to scroll through the

LCD display until Macro is displayed. Press OK.

3. The LCD displays PWR Macro. Press until the

LCD displays Key Macro OK or  . Press

OK.

4. The LCD displays Add Macro. Press OK.

5. The LCD displays Sel Macro Key or . Press

the key you want to program the macro on. NOTE: Any function key like M1, M2, or M3, other

than EXIT or  can be a macro key.

6. The LCD displays Press Keys In. When you press

 you can continue reading instructions. Press the

keys for the macro in the order they should occur.

For example, press TV and then Chan .

7. When you have finished programming your key

macro, press and hold P until the LCD displays

Success and exits.

DELETING A KEY MACRO

To delete a key macro, perform the following steps:

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the or keys to scroll through the

LCD display until Macro is displayed.

Press OK.

3. The LCD displays Pwr Macro. Press  until

the LCD displays Key Macro. Press OK.

4. Press . The LCD displays DLT Macro. Press OK.

5. The LCD displays Press the Key or . Press the

key for the macro you want to delete.

6. The LCD displays Are U Sure. Press OK.

7. The LCD displays Success and exits.

SETTING TIME MACROS

Yo u r RadioShack 8-in-1 LCD Remote allows you to set up time macros to schedule certain commands in advance, either daily or weekly. For example, you could set up the remote to record a certain program for you on a daily or weekly basis.

NOTE: If you have not yet set the time, the LCD

Setting a Daily Time Macro

To set up a daily time macro, perform the following steps:

1. Press and hold P until the LCD displays

2. Use the or keys to scroll through the

3. Use the or keys to scroll through the LCD

4. The LCD displays Add Macro. Press OK.

5. The LCD displays Enter Time. Press OK. The LCD

6. Set the time for your macro using the same

7. The LCD displays Daily OK or  . Press OK.

displays Set Clock and the remote returns to the main setup screen. See “Setting the Clock” on page 10.

Code Set OK or  .

LCD display until Macro is displayed.

Press OK.

display until Time Macro is displayed. Press OK.

displays the time of the current macro set, if any.

procedure as for setting the clock. See “Setting the

Clock” on page 10. Press OK after setting the clock.

8. The LCD displays Press Keys In. When you press

 you can continue reading instructions. Press

keys in the order they should occur in your time

macro.

9. After the first key press, the LCD displays Hold P

to Save. Press and hold P until the LCD displays

Success and exits.

Setting a Weekly Time Macro

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the or keys to scroll through the

LCD display until Macro is displayed.

Press OK.

3. Use the or keys to scroll through the LCD

display until Time Macro is displayed. Press OK. NOTE: If you have not yet set the time, the LCD will

display Set Clock and the remote will return to the main setup screen. See “Setting the Clock” on page 10.

4. The LCD displays Add Macro OK or  .

Press OK.

5. The LCD displays Enter Time. Press OK. The LCD

displays the time of the current macro set, if any.

6. Set the time for your macro using the same

procedure as for setting the clock. See “Setting the

Clock” on page 10.

7. The LCD displays Daily OK or  . Press .

8. The LCD displays Weekly OK or  . Press

OK.

9. The LCD displays Sunday. Use the   keys to

select the day you want the time macro to execute.

Press OK.

10. The LCD displays Press Keys In. When you press

 you can continue reading instructions.Press

keys in the order they should occur in your macro.

11. After you have completed your macro sequence,

press and hold P until the LCD displays Success

and exits.

Deleting a Time Macro

1. Press and hold P until the LCD displays

Code Set OK or  .

2. Use the or keys to scroll through the

LCD display until Macro is displayed.

Press OK.

3. Use the or keys to scroll through the LCD

display until Time Macro is displayed. Press OK.

4. The LCD displays Add Macro OK or  .

Press .

5. The LCD displays DLT Macro or  . Press

OK.

6. The LCD displays the currently set time macro.

Press OK.

+ 51 hidden pages