SciCan SANAO Red Dot,SANAO Blue Dot,SANAO Green Dot Quick Reference Manual

* only E-STATIS Advantage

Displays actual bur rotational speed

5 customizable endo settings*

Presets of all common handpiece
transmissions plus two customizable presets

Programmable motor torque
accommodates all rotary fi le requirements*

Customizable operative modes

Light on/off

User friendly display menu

Red Dot - High Speed Attachment

Up to 200,000 RPM = Gear ratio 1:5
Crown & bridge removal or preparation, caries removal,
endo access

Blue Dot - Low Speed Attachment

Up to 40,000 RPM = Gear ratio 1:1
Polishing, caries removal in dentin, endo access, endo at
torque below 1.5 Ncm

Green Dot - Very Low Speed Attachment

Up to 8,000 RPM = Gear ratio 5:1
Endo at torque of 1.5 Ncm or above

SANAO

™

Handpieces - Quick Reference Guide

WARNING!

Risks when using handpieces with electric micro-motors.

Electric micro-motors generate signifi cantly more energy than conventional air
turbines and air motors. Due to the high torques and speeds poorly serviced,
damaged or misused handpieces may lead to overheating which could infl ict
severe burns on the patient.

Please observe the following:

• Carefully follow the maintenance instructions.

• Inspect the handpiece for external damage before each use.

• Run a test with the handpiece before each use.

Especially pay attention to unusual overheating, conspicuous noises
and vibrations.

• If a handpiece is found to be faulty, its use must be
immediately discontinued.

• Never lift cheeks or tongues with the handpiece.

IMPORTANT!

E-STATIS™ unit must be calibrated to the dental unit.
See reverse for calibration instructions.

SycoTec GmbH

Wangener S trasse 78
88299 Leutkirch Germany

Tel: [phone]
E-Mail: [e-mail]
Internet: ww w.sycotec.eu

SciCan Inc.

701 Technology Dr.
Canonsburg, PA 15317 USA

Tel: [phone]
Toll free: 1-800 -572-1211
Fax: [phone]
[e-mail]

Manufactured by: Distributed by:

SD-468 US EN R2. SANAO, E-STATIS and Your Infection Control Specialist are trademarks of SciCan Ltd.

SD-468 US EN R2_QRG TestDrive_Sanao.indd 1 16-08-19 1:56 PM

SANAO

™

Handpieces - Installation and Commissioning

SD-468 US EN R1. SANAO, E-STATIS and Your Infection Control Specialist are trademarks of SciCan Ltd.

Calibrate Foot Control

Press “Set up” key.
The display then goes in to set up mode.

Pressing the button starts the “psi/bar” calibration process.

Proceed as follows:

1. If “MAX” is not already displayed on the “PSI/BAR” button, press “PSI/BAR” once or twice until
“MAX” appears displayed on the “PSI/BAR” button.

2. When “MAX” is displayed the unit is ready to activate calibrating the maximum pressure.

3. Press the foot control ALL THE WAY DOWN and keep holding it down. Press and HOLD “PSI/
BAR” button, (while “MAX” is displayed and foot control is being held all the way down), until signal
sounds. Maximum pressure has now been calibrated (to equal 100%).

4. The “PSI/BAR” button should now have “MIN” displayed on it. If it does not, then press “PSI/BAR”
once or twice until “MIN” appears displayed on the “PSI/BAR” button

5. When “MIN” is displayed the unit is ready to activate calibrating the minimal pressure.

6. DO NOT PRESS THE FOOT CONTROL AT ALL, and Press and HOLD “PSI/BAR” button, (while
“MIN” is displayed), until signal sounds. Minimum pressure has now been calibrated (to equal 0%).

Calibration is finished.

100%

0%

SD-468 US EN R2_QRG TestDrive_Sanao.indd 2 16-08-19 1:56 PM